1. MyLoader
MyLoader is the bootloader only seen so far on Compex wireless routers. If you have seen this bootloader on other devices that you own please add them to the bottom of the page. Unlike CFE or Redboot, MyLoader is a menu driven bootloader like the standard one on all adm5120 platforms by Edimax, Sweex and others. There are more details on the standard bootloader available on the midge website: http://midge.vlad.org.ua
The following data is for COMPEX WP54AG (non WRT version) and is probably valid also for COMPEX NP27G:
Images used for updating firmware consist of update header(offset 0) and system image(size+crc32+gziped kernel+cramfs; offset 0x100f8). After verifying update header, system image is saved to the first mtd partition (mtd1, memory address: 0x1fc00000). When booting, MyLoader verifies(crc) flash stored image, ungzips it and runs kernel....
firmware update image description:
address: size description --------update header---------------------- 0x00000: 4B MAGIC (004d594c) 0x00004: 4B CRC?? (unknown checksum, can be disabled by setting to 00000000) 0x00010: 8B 2xDEVICE ID 0x00050: 4B size of system image (from 0x100f8) -------system image------------------------ 0x100f8: 4B size of gzipped kernel+cramfs 0x100fc: 4B crc32 of gzipped kernel+cramfs (from 0x10100 to eof) 0x10100: n/a gziped linux kernel + cramfs filesystem
(note: there is a lot of another data in update header, but you have to modify only size (0x50) and disable checksum (0x4) to load modified system image)
Below is a set of instructions which can be used to update the bootloader to CFE using the bundle provided for the WP54-WRT. I have tried this on my WP54G-1D but after a few seconds the board freezes (EDIT: this is probably because CFE for WP54-WRT checks for "security device" attached to GPIO0, GPIO1 and will not run on non WRT versions of WP54). Also JTAG seems to be a bit odd on these boxes, and as yet I have to get some sensible looking results from it.
MyLoader version 2.32.0515 System memory: 16MB ram, 4MB flash Probe Flash Device: 00400000 at bfc00000 Flash Device: Found 1 x16 devices at 0x0 in 16-bit mode Amd/Fujitsu Extended Query Table v1.1 at 0x0040 number of CFI chips: 1 Load Firmware Loading Firmware CRC error. Update Firmware (Image Mode) Mini TFTP Server 1.0 (IP : 192.168.168.1) Usage (Windows 2000/XP) : tftp -i 192.168.168.1 put <filename> Main Menu 1 - Load Firmware 2 - Load Program 3 - BIOS Setup 4 - Fdisk Utility 5 - Update Flash (Binary Mode) 6 - Update Firmware (Image Mode) 7 - Reboot System Please select :
As you can see I have pre-broken my image, MyLoader checks the whole image against a CRC before booting. At this point you can select 5, Update Flash which opens a new menu.
Update Flash (Binary Mode) 1 - Update BIOS 2 - Update System Paramters 3 - Update Board Paramters 4 - Update Partition Table 5 - Update Partition Please select :
Then select 1 - Update BIOS. You can send any binary file, and it will just overwrite the bootloader.Warning -- This will toast your router if you send a bad file.
Update BIOS Mini TFTP Server 1.0 (IP : 192.168.168.1) Usage (Windows 2000/XP) : tftp -i 192.168.168.1 put <filename>
You then TFTP your file to the router and given any luck you should see:
Starting the TFTP download from IP (192.168.168.2)... ........ TFTP download completed... Update BIOS ......................... Done Update Flash (Binary Mode) 1 - Update BIOS 2 - Update System Paramters 3 - Update Board Paramters 4 - Update Partition Table 5 - Update Partition Please select :
Escape out of that menu:
Main Menu 1 - Load Firmware 2 - Load Program 3 - BIOS Setup 4 - Fdisk Utility 5 - Update Flash (Binary Mode) 6 - Update Firmware (Image Mode) 7 - Reboot System Please select :
Then select 7. This is the point of no return. If you were sensible enough to save a copy of the previous images then continue at your leasure.
Reboot System CFE version 1.2.5 for WP54G (32bit,SP,LE,MIPS) Build Date: Wed Aug 16 09:09:30 SGT 2006 (ttyaw@linux01) Initializing Arena. Initializing PCI. [normal] PCI bus 0 slot 0/0: ADMtek ADM5120 Host Bridge (host bridge) PCI bus 0 slot 2/0: Atheros product 0x001a (ethernet network, rev 0x01) Initializing Devices. CPU type 0x1800B: 175MHz Total memory: 0x1000000 bytes (16MB) Total memory used by CFE: 0x80F83000 - 0x80FFFAE0 (510688) Initialized Data: 0x80FBA824 - 0x80FBCA50 (8748) BSS Area: 0x80FBCA50 - 0x80FBDAE0 (4240) Local Heap: 0x80FBDAE0 - 0x80FFDAE0 (262144) Stack Area: 0x80FFDAE0 - 0x80FFFAE0 (8192) Text (code) segment: 0x80F83000 - 0x80FBA115 (225557) Boot area (physical): 0x00F42000 - 0x00F82000 Relocation Factor: I:E1383000 - D:E1383000 CFE>
At which point I can enter commands for a few seconds, but after that it freezes for me.