1. Table of Contents
Contents
2. Siemens Gigaset SX551
The Siemens Gigaset SX551 is an WLAN DSL Router. This device is also distibuted with a modified firmware by the Dutch provider KPN as the first generation Experia box (silver version). This is the version I (SA007) have.
3. Basic hardware info
The device has the following connectors on the rear (left to right).
- Auxiliary antenna.
- Telephone 1 connector (POTS).
- Telephone 2 connector (POTS).
- Line connector (Fallback).
- ADSL input connector.
- 4 numbered RJ45 10/100 MBit connectors.
- One USB 2.0 Port (2nd can be added with soldering).
- Reset button.
- Large On/Off button.
- Power connector (12V 1.2A).
- Main antenna.
It supports ADSL/ADSL2/ADSL2+ connections, WEP/WPA. Standard the USB port can be used for a fileserver (FAT only) or a very small number of printers.
4. Opening the casing
First remove the 4 screws on the bottom site (inside the U shaped anti-skid pads). Around the device there are 5 clips, to click them open you must pull the underside outward. The clips are:
- Rear.
- Above the reset button.
- Sides.
- Centered.
- Front.
- Around OK LED.
- Around Tel1 LED.
5. Extended hardware information
5.1. Main processor
The main processor is an Texas Instruments TNETD7300AZDW Processor, covered by a soldered in place cooler, an AR7 that should work with the AR7Port of openWRT (yet untested).
5.2. Memory
Onboard is a PSC A2V46S40BTP 256Mbit (32MiB) SDRAM Memory chip.
5.3. Flash
The flash chip is an Excelsemi ES29LV160DB-70RTG 16Mbit (2MiB) 3.0V Flash memory, hopefully this is enough for OpenWRT.
5.4. USB 2.0 Controller
The device probably will not have any USB problems since the USB controller is a seperate chip. The controller is a VIA VT6212L. A 4-port USB 2.0 Host controller. Unfortunatly only one port is external by default, but this can be expanded to 2 ports by adding some components and a larger connector, as soon as this works it will be posted here.
5.5. VoIP Controller
VoIP is done by a VoicePump VP101X12DQC Chip (located at the bottom side of the PCB). This chip is not yet supported. An LegerIty Le9502BTC Provides a ringing interface circuit. Some other inferfacing is done by a LiteLink CPC5621A Phone Line Interface IC Both seem to connect to the VoicePump.
5.6. Switch chip
The internal switch is a Marvell 88E6060-RCJ1 6-port (4 external, 1 to the router itself, 1 unused) 10/100 switch with autosensing.
5.7. Wireless card
I removed the wlan card from the SX551 and plugged it into my laptop:
# lspci
02:02.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
# lspci -n
02:02.0 0200: 168c:0013 (rev 01)
# lspci -v
02:02.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
Subsystem: Accton Technology Corporation Unknown device 4412
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at c0210000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
# lspci -vv
02:02.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
Subsystem: Accton Technology Corporation Unknown device 4412
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
Region 0: Memory at c0210000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Which means it is an normal Atheros card which should work flawlessly with MadWifi.
5.8. Hardware with unknown function
Texas Instruments TNETV100PZ, probably some sort of companion chip of the AR7.
This may be a VLYNQ to PCI bridge, used for the WiFi and USB controllers.
6. Pinouts
I'm still figuring out pinouts. Most headers are useless and only used to glue the wireless wires to.
Userless headers:
- P1 - Next to the wlan card.
- P2 - At the far side of the wlan card.
- P3 - At an slight angle nest to the 4-port RJ45 block.
- P4 - In the corner of the auxilery antenna.
- P5 - Between the USB 2.0 controller and the main processor.
JP4 - 4 Pin, directly connects to the Line port on the rear of the modem. J4 - 10 Pin. Serial console.
- Not connected.
- Not connected.
- RXD.
- Not connected.
- TXD.
- Not connected.
- Not connected.
- Not connected.
- Gnd.
- +3.3V.
7. Serial console
A serial console can be conneced to J4, according to the pinout above.
The serial signals are at a 3.3V level, so you need to use a level convertor, see OpenWrtDocs/Customizing/Hardware/Serial Console
The serial signal itself is 115200 baud, 8 databits, 1 stopbit, no parity (8N1).
8. Rescue mode
The SX551 has a rescue mode, which is reached by holding start while powering on the device, and then pressing 'reset' three times. In this mode, the router is reachable at 192.168.2.1 and runs a webserver. The webpages on that are password-protected: the username and password have been found, though. The username is root, the password is LAYS?8<}HJ?]W.i&c*oV[ouHwzM:QMV]9:XQ(u (yes, the complete string). This mode is quite useless, though: First of all, it'll only accept files which have BRN4519JW[null] as the last few bytes. A bit of hexediting can solve this, but the second problem is that it doesn't seem to recognize the flash: at the serial console, this shows up:
upgrade CGI > process content-type...
boundary=-----------------------------3334805413133863571136168153
endbound=-----------------------------3334805413133863571136168153--
content-length: 1485187
lens_up=0, call recv(), recv() returned, lens_up=512...
remove 0xD, 0xA
remove 0xD, 0xA
remove 0xD, 0xA
parse file upload
value: sx551-w-a-fw1_08_SWD-for-bootloader.bin
remove 0xD, 0xA
content-type upg_buf = Content-Type: application/octet-stream
remove 0xD, 0xA
remove 0xD, 0xA
remove 0xD, 0xA
remove 0xD, 0xA
#####8<#####
count=1484810
comparing UI...
comparing FW...
found signature: 78h 56h 34h 12h
ulImgLens=254705, LENGTH[2]-12=1769460
length checking OK
search_signature: image's lens = 254976
write to flash task...
period_task running 1200
update UI and FW, length=1484800...
Flash not found
9. Original bootlog
===========================================================
TI ADSL AR7300 Loader 0.71.4 build Oct 18 2005 11:13:40
Broad Net Technology, INC.
===========================================================
ESS ES29LV160D bottom boot 16-bit mode found
Copying boot params.....DONE
Flash Checking Passed.
Unzipping web at 0x94f30000 ... [LZMA] done
Unzipping code at 0x94000000 ... [LZMA] done
That really is all...
In the rescue-mode, which can be reached by pressing the reset when you start de device and then pressing the reset three times after that. (tnx equinoxe for that tip)
Then the output becomes:
===========================================================
TI ADSL AR7300 Loader 0.71.4 build Oct 18 2005 11:13:40
Broad Net Technology, INC.
===========================================================
ESS ES29LV160D bottom boot 16-bit mode found
Copying boot params.....DONE
Reset button was pressed
Click 1...
Click 2...
Click 3...
Activating recovery tool...
Unzipping web at 0x94f30000 ... [ZIP] done
Unzipping code at 0x94000000 ... [ZIP] done
Boot ETCPIP running ...
In C_Entry() function ...
install_exception
sys_irq_init
system startup...
tcpip_startup...
ESS ES29LV160D bottom boot 16-bit mode found
pBootParams=B01F0000
Set flash memory layout to BPARAMS+RECOVER_KERNEL
Bootcode version: 0.71.4
Serial number: J622411250
Hardware version: 01
!!No configuration file present!!
default route: 0.0.0.0
BufferInit:
BUF_HDR_SZ=16 BUF_ALIGN_SZ=0 BUFFER_OFFSET=80
BUF_BUFSZ0=384 BUF_BUFSZ1=1632
NUM_OF_B0=500 NUM_OF_B1=500
BUF_POOL0_SZ=200000 BUF_POOL1_SZ=824000
Buf0_Block b4330bc0 Buf1_Block b42678f0
BUF0[0]=0xb4330bc0 BUF1[0]=0xb42678f0
buffer0 pointer init OK!
buffer1 pointer init OK!
init_if() ; gConfig.Interface[0].Link_Type is [4]
Interface 0 ip = 127.0.0.1
init_if() ; gConfig.Interface[1].Link_Type is [1]
MAC Address: 00:01:e3:da:90:69
MAC1 [RX=128 TX=1]: TI External PHY
Interface 1 ip = 192.168.2.1
init_if() ; gConfig.Interface[2].Link_Type is [0]
RUNTASK id=1 if_task if0...
RUNTASK id=2 if_task if1...
RUNTASK id=3 timer_task...
RUNTASK id=4 period_task...
RUNTASK id=5 dhcp_daemon...
RUNTASK httpd...
RUNTASK id=8 dhcpd_mgmt_task...
Starting Multitask...
MTstart2() begin ...
period_task running!!!
httpd: listen at 192.168.2.1:80
dhcpd_mgmt_task started...
period_task running 60
In this mode it does respond to some input.
Pressing u or U gives a list of some (non-intresting) debug info about transmitted and received packets.
Those are the only 2 ascii characters the console responds to with a message other than "I'm still alive ..."
10. OpenWRT status
Untested