User Tools

Site Tools


arv7519

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

arv7519 [2013/01/18 21:52]
— (current)
Line 1: Line 1:
-====== Arcadyan ARV7519PW ====== 
-This device is distributed in the Netherlands by KPN as the `KPN Experia Box` 
- 
-===== Known Supported Versions ===== 
-^ Ver. ^ OpenWrt Version Supported ^ 
-| ?   | ?| 
- 
-===== Hardware Highlights ===== 
-^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ UART ^ 
-| Lantiq Xway Danube @333Mhz Dual Core | 64MB | 8MB | 4 Ports | Yes | Yes | Yes | 
- 
-The PCB looks very similar to [[toh:​astoria:​ARV752DPW22]] when looking at the CPU, RAM, power supply and ethernet connectors. The ARV7519 has the same design origin but has only 1 USB connection and no ISDN capabilities. So porting should be easy if one is able to upload custom firmware 
-==== Openwrt status ==== 
- 
-==== Flash Layout ==== 
-Please check out the article [[doc:​techref:​Flash Layout]]. It contains an example and a couple of explanations. 
- 
-^  Modified Flash Layout ​ ^^^^^ 
-^ partition ^ start ^ end ^ size ^ description ^ 
- 
-===== Hardware ===== 
-==== Info ==== 
-| **Architecture:​** MIPS |  
-| **Vendor:** Arcadyan |  
-| **Bootloader:​** [[doc:​techref:​bootloader:​brnboot]] |  
-| **System-On-Chip:​** ​ [[http://​www.lantiq.com/​products/​broadband-customer-premises-equipment/​adsl/​xwaytm-danube/​xwaytm-danube/​|Lantiq Danube PSB 50702 E Rev 1.3 or 1.5 (MIPS 24Kec)]]| ​ 
-| **CPU/​Speed** 333 Mhz Dual Core | 
-| **Flash-Chip:​** EN29LV640L | 
-| **Flash size:** 8Mbyte |  
-| **RAM:** 64 MiB |  
-| **RAM Chip:** Zentel A3S12D40ETP-G6| 
-| **Wireless:​** Ralink rt3062F |  
-| **Ethernet:​** RTL8306G| 
-| **Internet:​** ADSL2+ 
-| **USB:** Yes 1 x 2.0 |  
-| **Phone:​** ​ 2x FXS + 1 shared with ADSL| 
-| **Serial:** [[#​Serial|Yes]] |  
-| **JTAG:** No | 
- 
-===== Serial ===== 
--> [[doc:​hardware:​port.serial]]. 
- 
-Board voltage is 3.3V so you will need resistors if you want to connect it directly to PC serial port, or you can use usb to serial adapters which are already at 3.3v. 
- 
-===== Pictures ==== 
-{{:​experia_pxb.jpg|}} 
- 
-==== Bootstrap settings ==== 
-The bootstrap options is  similar to the [[toh:​arcadyan:​ARV752DPW]]. The PCB design underneath the SoC is almost identical. The bootstrap option described for the ARV752DPW work on the ARV7519 as well. The resistor numbers (R65 and R80) are equal as are the points of soldering. 
- 
-===== Bootlog ====== 
- 
-==== Normal boot ==== 
-<​code>​ 
-ROM VER: 1.0.3 
-CFG 01 
-Read� 
-ROM VER: 1.0.3 
-CFG 01 
-Read EEPROMX 
- X 
- 
- 
- 
-======================================================================= 
-Wireless ADSL Gateway DANUBE Loader v2.00.11 build Jul  1 2010 10:19:30 
-                    Arcadyan Technology Corporation 
-======================================================================= 
-EON EN29LV640L top boot 16-bit mode found 
- 
-Copying boot params.....DONE 
- 
-Press Space Bar 3 times to enter command mode ... 
-Flash Checking [1] Passed. 
-Image[1] at 0xb0870000, len:​1709697,​ type:0 
-Image[2] at 0xb0a11800, len:6893, type:10 
-Image[3] at 0xb0a13400, len:225078, type:11 
-Image[4] at 0xb0a4a400, len:225005, type:12 
-Image[5] at 0xb0a81400, len:168592, type:50 
-Image[6] at 0xb0aaa800, len:452618, type:90 
-Firmware image at 0, ART image at -1 
- 
-Run-up Normal Firmware... 
- 
-Unzipping firmware [1(6)] at 0x80002000 ... [ZIP 3] [ZIP 1]  done 
-Run-time code running ... 
- 
-In c_entry() function ... 
-install_exception ​ 
-Co config = 80008483 
-[INIT] Interrupt ... 
-##### _ftext ​     = 0x80002000 
-##### _fdata ​     = 0x80687550 
-##### __bss_start = 0x80756574 
-##### end         = 0x83017AC8 
-allocate_memory_after_end>​ len 847908, ptr 0x8301fad0 
-##### Backup Data from 0x80687550 to 0x8301FAC8~0x830EEAEC len 847908 
-##### Backup Data completed 
-##### Backup Data verified 
-[GPIO FLOW] SetGpio() Begin .. 
-gptu: totally 6 16-bit timers/​counters 
-Init timer = 0 
-[GPIO FLOW] SetGpio() End. 
-[INIT] System Log Pool startup ... 
-[INIT] MTinitialize .. 
-[INIT] usrclk 
-CPU Clock 333333334 Hz 
-mips_counter_frequency:​166666667 
-r4k_offset: 00028b0a(166666) 
-init_US_counter : time1 = 260430 , time2 = 40260482, diff 40000052 
-US_counter = 48 
- cnt1 40987778 cnt2 40990033, diff 2255 
-Runtime code version: 01.01.111 
-System startup... 
-[INIT] Memory COLOR 0, 3000000 bytes .. 
-[INIT] Memory COLOR 1, 262144 bytes .. 
-[INIT] Memory COLOR 2, 4565152 bytes .. 
-EON EN29LV640L top boot 16-bit mode found 
- 
- 
-</​code>​ 
- 
-==== Reset button pressed ==== 
-This is the bootlog when booting with the reset button pressed. It also launches a webserver at 192.168.2.254. The webserver reports to be Apache 0.6.5, which seems false. 
-<​code>​ 
-ROM VER: 1.0.3 
-CFG 01 
-Read� 
-ROM VER: 1.0.3 
-CFG 01 
-Read EEPROMX 
- X 
- 
- 
- 
-======================================================================= 
-Wireless ADSL Gateway DANUBE Loader v2.00.11 build Jul  1 2010 10:19:30 
-                    Arcadyan Technology Corporation 
-======================================================================= 
-EON EN29LV640L top boot 16-bit mode found 
- 
-Copying boot params.....DONE 
- 
-RESET_BTN was pressed... 1 
-RESET_BTN was pressed... 2 
- 
-Wake up Tiny_ETCPIP_KERNEL... 
- 
-Unzipping Tiny Kernel at 0x80002000 ... [ZIP 1]  done 
-Tiny ETCPIP running ... 
- 
-</​code>​ 
- 
-===== Tags ===== 
-{{tag>​FastEthernet 4Port USB 64RAM 4Flash MIPS MIPS32 24K ADSL2plus fxo}} 
  
arv7519.1358542345.txt.bz2 · Last modified: 2013/01/18 21:52 (external edit)