User Tools

Site Tools


inbox:huawei:huawei_hg659_b

Huawei HG659 b

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

This router is manufactured by Huawei for Spark, Vodafone and Dodo in New Zealand and Australia to ADSL/vDSL & Fibre customers.

HG659b Spark Router

OpenWrt support

Not supported.

Supporting activities

OEM Firmware

Firmware is interchangeble with the HG659 from Vodafone, it only loads through the cfe web interface though.

Images

Default passwords

  • Spark: admin/admin
  • Vodafone: Admin/VF-NZhg659 or Admin/@[Last 8 digits of the serial number] or vfremote/@[Last 8 digits of the serial number]
  • Dodo: admin/admin@HG659

Experimental firmware

List experimental firmware download links here.

None at this time.

  • External image (add link)
  • trunk image (add link)

Installation

Installing OpenWrt

Flashing ANY Firmware

You must set your TCP/IP v4 protocol to:

  1. IP: 192.168.1.100
  2. Netmask: 255.255.255.0
  3. Gateway: 192.168.1.1

Then:

  1. Power off the router.
  2. Press reset button.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Acces to http://192.168.1.1 and upload binary file.
  5. Wait until router reboots.

Hardware

highlights

SoC Ram Flash Network USB Serial JTag
BCM63168@400MHz 128MiB 128MiB 4 + 1 2 x 2.0 Yes (5-Pin) ?

Info

Architecture: MIPS
Vendor: Broadcom
Bootloader: CFE 1.0.38-114.174
Board ID: 963268_hg659v3
System-On-Chip: Broadcom BCM63168
CPU/Speed BCM631683D0 / 400 MHz
NAND flash: 128 MiB (TOSHIBA TC58NVG0S3E, id 0x98d1 block 128KB size 131072KB)
RAM 128 MiB / DDR2
Wireless BCM6362 802.11b/g/n (SoC)
Antenna 2x
Ethernet: BCM53124
USB Yes
Power adapter 12V DC 2A / HW-120200U6W
Serial: Yes
JTAG: ?

Photos

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

N/A

Flash Layout

FIXME Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

$ cat /proc/mtd
dev:    size   erasesize  name
mtd0: 02300000 00020000 "rootfs"
mtd1: 08000000 00020000 "all"
mtd2: 00d20000 00020000 "config"
mtd3: 000a0000 00020000 "equip"
mtd4: 000a0000 00020000 "upgflag"
mtd5: 00020000 00020000 "blrom"
mtd6: 000a0000 00020000 "rootfstag"
mtd7: 02940000 00020000 "reserved"
mtd8: 038a0000 00020000 "html"
mtd9: 001a0000 00020000 "wlanrf"
mtd10: 07ea0000 00020000 "kernel"
mtd11: 05ba0000 00020000 "kernelbak"

<5>Creating 12 MTD partitions on "brcmnand.0":

<5>0x000000000000-0x000008000000 : "all" *
<5>0x000000000000-0x000000020000 : "blrom"
<5>0x000000020000-0x0000000c0000 : "rootfstag"
   0x0000000c0000-0x000000160000 "rootfstagbak"  ** Guessed slave
<5>0x000000160000-0x000008000000 : "kernel"
<5>0x000000160000-0x000002460000 : "rootfs"
<5>0x000002460000-0x000008000000 : "kernelbak"
   0x000002460000-0x000004600000 : "rootfsbak"  ** Guessed slave
<5>0x000004760000-0x000008000000 : "html"
<5>0x000004760000-0x0000070a0000 : "reserved"
<5>0x0000070a0000-0x000007dc0000 : "config"
<5>0x000007dc0000-0x000007e60000 : "equip"
<5>0x000007e60000-0x000008000000 : "wlanrf"
<5>0x000007e60000-0x000007f00000 : "upgflag"

The "equip" partition stores some info used by the OEM firmware

"equip" /dev/mtd3
offsets info example
0x0028-0x0037 Serial Number U7D8W15914001530
0x0108-0x0127 WLAN SSID SPARK-SY7RB7
0x0128-0x014F WLAN Key LDKE3SAAXX
0x01f8-0x0217 WLAN SSID (5G) SPARK-SY7RB7-5G
0x0218-0x023F WLAN Key (5G) LDKE3SAAXX

Opening the case

It only has two philip screws and then you need to apply some pressure to open the case.

Serial

Use a serial TTL 3.3V adapter to connect your PC with HG659b. With an USB adapter connect only TX, RX and GND.

Settings:

  • Baudrate: 115200
  • Data bits: 8
  • Parity: None
  • Stop bits: 1

Used an FT232RL ttl converter.

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootlogs

OEM bootlog

HELO CPUI L1CI HELO CPUI L1CI DRAM ---- PHYS STRF 400H PHYE DDR3 SIZ4 SIZ3 SIZ2 DINT USYN LSYN MFAS LMBE RACE PASS ---- ZBSS CODE DATA L12F MAIN CFE version 1.0.38-114.174 for BCM963268 (32bit,SP,BE) Build Date: Tue Jul 7 09:07:57 CST 2015 (tangwen@tangwen) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name , id 0x98d1 block 128KB size 131072KB External switch id = 53125 Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 134217728 bytes (128MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Boot image (0=latest, 1=previous) : 0 Board Id (0-9) : 963268_hg659v3 Number of MAC Addresses (1-32) : 10 Base MAC Address : 00:11:22:44:55:66 PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Boot :e=192.168.1.1:ffffff00 h=192.168.1.100 g= r=f f=vmlinux i=bcm963xx_fs_kernel d=1 p=0 *** Press any key to stop auto run (3 seconds) *** Auto run second count down: 0 Power down external PHY port. Boot from main system! SIGN CHK ALWAYLYS. get bootflag = 1 check tag at block 1 crc ok Check Image Crc Success I have find vmlinux.lz at block 11 I have get vmlinux.lz size at block 24 Decompression OK! Entry at 0x803d1f90 Closing network. no Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x803d1f90 init started: BusyBox vv1.9.1 () starting pid 308, tty '': '/etc/init.d/rcS' RCS DONE starting pid 310, tty '': '/bin/sh' BusyBox vv1.9.1 () built-in shell (ash) Enter 'help' for a list of built-in commands. rootdir=/ table='/etc/devicetable' mount config success mount coredump success -/bin/sh: cannot create /proc/tty/mode: nonexistent directory Loading drivers and kernel modules... Start mic now ... GlobeMac Init OK load cfm ok. ##sendmsg return 16, errno 0. INSMOD START...... retry xhci retry xhci done INSMOD Done INSMOD ETH START...... INSMOD ETH Done ethcmdVportEnable--------SUPPORT_ATP_ETH_BCM_EXT_SWITCH_53125----- ARL table flush done MASK- ifconfig [eth0]********** device eth0 is not a slave of br0 [tv_sec:25 tv_usec:31660] FILE: wlancmsinit.c FUNC: ATP_WLAN_Init LINE: 239: Enter in the ATP_WLAN_Init. INSMOD wlan START...... INSMOD wlan Done Chain FWD_DEFAULT doesn't exist. Chain FWD_DEFAULT doesn't exist. LedcmswpsChgProc :9 Setting SSID: "SPARK-SY7RB7" WlanSetSsid: SSID=SPARK-SY7RB7 wlctl: Unsupported wlancms: events/0 is running as Real Time process. wlancms: events/1 is running as Real Time process. begin WlanStartServices... wlan wps enabled... begin WlanUpInterfaces... wps_gpio_led_init Setting SSID: "SPARK-SY7RB7-5G" WlanSetSsid: SSID=SPARK-SY7RB7-5G wps_gpio_led_cleanup wlctl: Unsupported wlancms: events/0 is running as Real Time process. wlancms: events/1 is running as Real Time process. Sorry, rule does not exist. Sorry, rule does not exist. Sorry, rule does not exist. Sorry, rule does not exist. begin WlanStartServices... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0x1008 acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0xe03a OFF wlan wps enabled... wps_gpio_led_init begin WlanUpInterfaces... 0x06a4 atp: cur kernel version:[2.6.30] 1 Open file /var/radvd/radvdlocalbr0.conf faild !FILE[ipv6commoncms.c] LINE[584] Open file /var/radvd/radvdlocalbr0.conf faild !FILE[radvdcms.c] LINE[2578] RadvdULACtlSetLocalCfg meet error !FILE[radvdcms.c] LINE[2422] Open file /var/radvd/radvdlocalbr1.conf faild !FILE[ipv6commoncms.c] LINE[584] Open file /var/dhcp/dhcp6s/dhcp6slocalbr0.conf faild !FILE[ipv6commoncms.c] LINE[584] Open file /var/dhcp/dhcp6s/dhcp6slocalbr1.conf faild !FILE[ipv6commoncms.c] LINE[584] Sorry, rule does not exist. lBridgeKey is 0 ============GET Interface Failed devName:nas0 Create interface OVER sleep count [0] sleep count [1] main 564 devName:nas0 rm: cannot remove '/var/wan/wan2interface': No such file or directory Start Eth Oam! mv: cannot rename '/var/wan/temp': No such file or directory After [50] ms, [pppc -I ppp258] start with pid [2227]============GET Interface Failed WAN:InternetGatewayDevice.WANDevice.4.WANConnectionDevice.1.WANPPPConnection.1 check not init. ************************Write db to flash now ... done sync iptables: No chain/target/match by that name iptables: No chain/target/match by that name iptables: No chain/target/match by that name iptables: No chain/target/match by that name iptables: No chain/target/match by that name iptables: No chain/target/match by that name Current sntp process is 2431! WAN: file[guestnetworkcmsinit.c] line[20] Init Guest network Sorry, rule does not exist. Sorry, rule does not exist. [(INFO)00:00:00.103-voice_init.c:L1282] ---VOIPER ENHANCE YOUR LIFE!--- [(INFO)00:00:00.103-voice_init.c:L1283] COMPILE DATE: Jul 7 2015, TIME = 09:07:29 [(DBG)00:00:00.104-voice_init.c:L1285]In the AppStart, the PID is 2435, and the PPID is 1 [(DBG)00:00:00.390-LineMngSipDnsFlow.c:L410]In the LINE_DnsThreadMain, the PID is 2528, and the PPID is 2526 [(DBG)00:00:00.443-tapi.c:L2710]TAPI CREATE Oper Succ![obj:0xffffffff, dev:24, chres:0, call:PSTN] [(DBG)00:00:00.444-tapi.c:L2465]Alloc PSTN_UP 0 channel Succ. [dev=24, Chres = 0] [(DBG)00:00:00.444-tapi.c:L2710]TAPI CREATE Oper Succ![obj:0xffffffff, dev:25, chres:1, call:ISDN] [(DBG)00:00:00.445-tapi.c:L2523]Alloc ISDN_UP 0 channel Succ. [dev=25, Chres = 1] [(DBG)00:00:00.445-tapi.c:L2710]TAPI CREATE Oper Succ![obj:0xffffffff, dev:26, chres:2, call:ISDN] [(DBG)00:00:00.445-tapi.c:L2523]Alloc ISDN_UP 1 channel Succ. [dev=26, Chres = 2] TAPI_AllocResource() OK! [(DBG)00:00:00.448-tapi.c:L742]TAPI thread thread started with pid 2538BOS: Enter bosInit bosTimerInit Enter bosAppInit Exit bosAppInit BOS: Exit bosInit Created message queue "HDSP", depth 40, id 1 [(DBG)00:00:00.452-tapi_cb.c:L66]Start TCB Succ! [(DBG)00:00:00.527-sstptdadaptor.c:L461]In the TptdPktRecv, the PID is 2550, and the PPID is 2526 [(DBG)00:00:00.528-stackinit.c:L243]--------<=LEAVE:SipStackInit -------- =OpenBcmPwrMngtCfg=1111==== =OpenBcmPwrMngtCfg=1111==== =OpenBcmPwrMngtCfg=1111==== ==========ATP_SYS_SetConsole_Type======[0] [(DBG)00:00:01.452-player_nut.c:L288]In the PLAYER_FeedPktThread, the PID is 2580, and the PPID is 2526 [(ERR)00:00:01.453-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.453-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.454-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.454-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.454-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.454-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.454-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.454-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.454-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.454-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.455-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.455-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.455-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.455-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.455-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.455-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.455-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.456-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.456-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.456-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.456-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.456-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.456-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.456-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.457-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.457-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.457-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.457-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.457-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.457-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.457-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.457-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.458-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.458-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.458-Dplan_dmm.c:L603]FunOp Seek Fail [(ERR)00:00:01.458-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.458-Dplan_dmm.c:L563]FunPref Seek Fail [(ERR)00:00:01.458-voice_dplan_interface.c:L328]Del Tbl Fail [(ERR)00:00:01.458-Dplan_dmm.c:L563]FunPref Seek Fail [(ERR)00:00:01.458-voice_dplan_interface.c:L328]Del Tbl Fail [(DBG)00:00:01.459-voice_profilecfg.c:L172]--------=>ENTER:CUSTOM_ReadProfileBody -------- [(DBG)00:00:01.459-voice_profilecfg.c:L207]1_1:UE.CallWaitEnable=1 [(DBG)00:00:01.459-voice_profilecfg.c:L207]1_2:UE.MultiCallEnable=1 [(DBG)00:00:01.459-voice_profilecfg.c:L207]1_3:UE.ConferenceEnable=1 [(DBG)00:00:01.460-voice_profilecfg.c:L207]1_4:UE.CallTransferEnable=1 [(DBG)00:00:01.460-voice_profilecfg.c:L207]1_5:UE.OnHookEctEnable=1 [(DBG)00:00:01.460-voice_profilecfg.c:L207]1_12:UE.FlashAnswerCallWaiting=1 [(DBG)00:00:01.460-voice_profilecfg.c:L207]2_1:SIP.InfoMessageBodyMethod=1 [(DBG)00:00:01.460-voice_profilecfg.c:L207]2_2:SIP.SpecCharTransformString=# [(DBG)00:00:01.460-voice_profilecfg.c:L207]2_3:SIP.GetRemoteUserFromHeaderPAI=1 [(DBG)00:00:01.461-voice_profilecfg.c:L207]2_4:SIP.UriAddUserParameter=1 [(DBG)00:00:01.461-voice_profilecfg.c:L207]2_5:SIP.DTMF2833PayloadType=97 [(DBG)00:00:01.461-voice_profilecfg.c:L207]2_19:SIP.SendrecvAsSessionAttr=1 [(DBG)00:00:01.461-voice_profilecfg.c:L207]3_1:PBX.AutoSwitchTobackgroundCallDurBusyTone=0 [(DBG)00:00:01.461-voice_profilecfg.c:L207]3_2:PBX.BusyToneLastBeforeAutoSwitch=5 [(DBG)00:00:01.462-voice_profilecfg.c:L207]3_3:PBX.DailShortAndLongTimerEnable=0 [(DBG)00:00:01.462-voice_profilecfg.c:L207]4_1:LINEMNG.SipMainRegisterServerPreferredUsing=1 [(DBG)00:00:01.462-voice_profilecfg.c:L207]4_2:LINEMNG.SipDeRegisterWhenServerSwitchBack=0 [(DBG)00:00:01.462-voice_profilecfg.c:L207]4_3:LINEMNG.SipRegisterRandomDelay=30 [(DBG)00:00:01.462-voice_profilecfg.c:L207]4_4:LINEMNG.LineMngSipRemoveBindByFirstRegisterFail=1 [(DBG)00:00:01.462-voice_profilecfg.c:L207]4_5:LINEMNG.SipRemoveBindForEachDomainServer=0 [(DBG)00:00:01.463-voice_profilecfg.c:L207]4_6:LINEMNG.SipSwitchDelayTimeBetweenIPs=15 [(DBG)00:00:01.807-voice_profilecfg.c:L207]4_7:LINEMNG.SipDelayTimeBetweenServers=60 [(DBG)00:00:01.807-voice_profilecfg.c:L207]4_8:LINEMNG.SipDelayTimeBetweenRounds=900 [(DBG)00:00:01.808-voice_profilecfg.c:L207]4_9:LINEMNG.SipDelayTimeForPollLineBusy=60 [(DBG)00:00:01.808-voice_profilecfg.c:L207]4_10:LINEMNG.CallDelayTimeForSipAccountChange=10 [(DBG)00:00:01.808-voice_profilecfg.c:L207]4_11:LINEMNG_SipDelayTimerAferDnsTTL0=0 [(DBG)00:00:01.808-voice_profilecfg.c:L207]4_12:LINEMNG.OptionsDetectProxy=1 [(DBG)00:00:01.808-voice_profilecfg.c:L207]4_13:LINEMNG.OptionsDependOnRegister=0 [(DBG)00:00:01.809-voice_profilecfg.c:L207]4_14:LINEMNG.OptionsDelayTimeBetweenIPs=15 [(DBG)00:00:01.809-voice_profilecfg.c:L207]4_15:LINEMNG.OptionsDelayTimeBetweenServers=60 [(DBG)00:00:01.809-voice_profilecfg.c:L207]4_16:LINEMNG.OptionsDelayTimeBetweenRounds=300 [(DBG)00:00:01.809-voice_profilecfg.c:L207]5_1:DPLAN.CfuActiveDM=*21*[*X].#|*21# [(DBG)00:00:01.810-voice_profilecfg.c:L207]5_2:DPLAN.CfuDeactiveDM=#21*[*X].#|#21# [(DBG)00:00:01.810-voice_profilecfg.c:L207]5_3:DPLAN.CfuCheckDM=*#21*[*X].#|*#21# [(DBG)00:00:01.810-voice_profilecfg.c:L207]5_4:DPLAN.CfbActiveDM=*67*[*X].#|*67# [(DBG)00:00:01.811-voice_profilecfg.c:L207]5_5:DPLAN.CfbDeactiveDM=#67*[*X].#|#67# [(DBG)00:00:01.811-voice_profilecfg.c:L207]5_6:DPLAN.CfbCheckDM=*#67*[*X].#|*#67# [(DBG)00:00:01.811-voice_profilecfg.c:L207]5_7:DPLAN.CfnrActiveDM=*61*[*X].#|*61# [(DBG)00:00:01.812-voice_profilecfg.c:L207]5_8:DPLAN.CfnrDeactiveDM=#61*[*X].#|#61# [(DBG)00:00:01.812-voice_profilecfg.c:L207]5_9:DPLAN.CfnrCheckDM=*#61*[*X].#|*#61# [(DBG)00:00:01.812-voice_profilecfg.c:L207]5_10:DPLAN.McidDM=*39#|*392# [(DBG)00:00:01.813-voice_profilecfg.c:L207]5_11:DPLAN.CcbsActiveDM=*37# [(DBG)00:00:01.813-voice_profilecfg.c:L207]5_12:DPLAN.CcbsDeactiveDM=#37# [(DBG)00:00:01.813-voice_profilecfg.c:L207]5_13:DPLAN.CcbsCheckDM=*#37# [(DBG)00:00:01.814-voice_profilecfg.c:L207]5_14:DPLAN.AnswerOtherPortCIDDM=**09#|**09[*X].# [(DBG)00:00:01.814-voice_profilecfg.c:L207]5_15:DPLAN.StartWlanDM=***91# [(DBG)00:00:01.815-voice_profilecfg.c:L207]5_16:DPLAN.StopWlanDM=**#91# [(DBG)00:00:01.815-voice_profilecfg.c:L207]5_17:DPLAN.StartAnycallDM=***92# [(DBG)00:00:01.815-voice_profilecfg.c:L207]5_18:DPLAN.StopAnycallDM=**#92# [(DBG)00:00:01.816-voice_profilecfg.c:L207]5_19:DPLAN.ClirCode=*31# [(DBG)00:00:01.816-voice_profilecfg.c:L207]5_20:DPLAN.ClipCode=#31# [(DBG)00:00:01.816-voice_profilecfg.c:L207]5_21:DPLAN.SipUrgCallPriorLogicFault=1 [(DBG)00:00:01.817-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.817-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.817-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.817-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.818-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.818-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.818-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.818-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.818-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.818-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.819-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.819-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.819-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.819-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.819-LineMng.c:L708]Line[].CfgChgFlag = 0x0 [(DBG)00:00:01.819-LineMng.c:L708]Line[].CfgChgFlag = 0x000:01:11 Endpoint Event task started with pid 2589... [(DBG)00:00:03.618-tapi_cms.c:L627]TAPI_CMS thread started with pid 2602 ------------- gwSipStartup OK! ------------ CS PCM_READ thread started with pid 2605 [(DBG)00:00:03.827-voice_init.c:L299]***************************************** [(DBG)00:00:03.827-voice_init.c:L300] Voice Msg Process Start [(DBG)00:00:03.827-voice_init.c:L301]*****************************************Recvd netlink msg now ... Cms netlink msg 543256164 finished. Recvd netlink msg now ... Cms netlink msg 543256164 finished. temps:45 temps:47 Inetd app upnp:2204 exited: signal number [0], exit code [0]. Recvd netlink msg now ... Cms netlink msg 543256164 finished. Recvd netlink msg now ... Cms netlink msg 543256164 finished. Recvd netlink msg now ... Cms netlink msg 543256164 finished. Recvd netlink msg now ... Cms netlink msg 543256164 finished. Recvd netlink msg now ... Cms netlink msg 543256164 finished. Recvd netlink msg now ... Cms netlink msg 543256164 finished. temps:49 temps:50


OpenWrt bootlog

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


Notes

Tags

inbox/huawei/huawei_hg659_b.txt · Last modified: 2017/06/22 15:08 by Shad0w_General