User Tools

Site Tools


inbox:toh:netgear.cg3200

Netgear CG3200

Wireless Cable Voice Gateway used by the danish ISP "YouSee".

Hardware Highlights

CPU Ram Flash Modem Network USB Serial Pots JTag
ARMv6-compatible processor rev 4 (v6b) 64MiB 16MiB Docsis 3.0 4 x 1 Yes Yes 2 ?

Hardware

Info

Architecture: ARMv6
Vendor: TI/Intel
Bootloader: PSPU-Boot(BBU) 1.0.1.7
System-On-Chip: Puma5 TNETC4800
CPU Speed: 400 MHz
Flash-Chip: Spansion S25FL128P
Flash size: 16 MiB
RAM: 64 MiB
Wireless: mini-PCI
Ethernet: 4 x 10/100/1000
USB: Yes
Serial: Yes
JTAG: ?

Photos

Model Number

Front:

Photo of front

Back:

Photo of back

Opening the case

Note: This will void your warranty!

  • To remove the cover simply unscrew 6 screws in bottom of device.
  • There are four screws under the rubber feets.

Main PCB

Photo of PCB (coming as soon i learn howto upload)

Serial

This model has an 6-pin header (J6) that exposes a 3.3V serial port. Pins are listed below:

Pin 1 3,3V
Pin 2 RxD
Pin 3 nc
Pin 4 nc
Pin 5 TxD
Pin 6 GND

Serial connection parameters are : 115200,8N1

JTAG

Conectors

F-connector WAN port
4 * RJ45 LAN
2 * RJ11 Phone pots
1 * USB

Buttons

The device has 3 buttons, the reset i located under the device.

BUTTON Event
Reset reset
wifi
security

Other Info

ifconfig

br0       Link encap:Ethernet  HWaddr 00:1E:2A:03:87:C0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:1 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:28 (28.0 B)  TX bytes:0 (0.0 B)

cni0      Link encap:Ethernet  HWaddr 00:50:F1:80:00:00
          UP BROADCAST RUNNING PROMISC MULTICAST  MTU:1500  Metric:1
          RX packets:3 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:60 (60.0 B)  TX bytes:0 (0.0 B)

esafe0    Link encap:Ethernet  HWaddr 00:00:00:00:00:00
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

eth0      Link encap:Ethernet  HWaddr 00:1E:2A:03:87:C0
          UP BROADCAST RUNNING PROMISC MULTICAST  MTU:1500  Metric:1
          RX packets:136 errors:0 dropped:0 overruns:0 frame:0
          TX packets:128 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:10633 (10.3 KiB)  TX bytes:29756 (29.0 KiB)
          Base address:0xe000

lan0      Link encap:Ethernet  HWaddr 00:18:4D:FF:FF:04
          inet addr:192.168.101.1  Bcast:192.168.101.255  Mask:255.255.255.0
          inet6 addr: fe80::218:4dff:feff:ff04/64 Scope:Link
          UP BROADCAST RUNNING PROMISC MULTICAST  MTU:1500  Metric:1
          RX packets:48 errors:0 dropped:0 overruns:0 frame:0
          TX packets:52 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:4595 (4.4 KiB)  TX bytes:3688 (3.6 KiB)

lbr0      Link encap:Ethernet  HWaddr 00:50:F1:00:00:00
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:45 errors:0 dropped:0 overruns:0 frame:0
          TX packets:45 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:3150 (3.0 KiB)  TX bytes:4547 (4.4 KiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:42 errors:0 dropped:0 overruns:0 frame:0
          TX packets:42 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:3180 (3.1 KiB)  TX bytes:3180 (3.1 KiB)

mta0      Link encap:Ethernet  HWaddr 00:26:F2:66:29:51
          UP BROADCAST RUNNING  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

/proc/devices

Character devices:
  1 mem
  4 ttyS
  5 /dev/tty
  5 /dev/console
  5 /dev/ptmx
 10 misc
 32 docsis_mng
 36 soc_if_driver
 89 i2c
 90 mtd
128 ptm
136 pts
180 usb
189 usb_device
249 docsis_pp_counters
250 docsis_fltr_class
251 DOCINT
252 docsis_dbridge_mdf
254 led

Block devices:
  7 loop
 31 mtdblock

/proc/mtd

dev:    size   erasesize  name
mtd0: 00020000 00010000 "U-Boot"
mtd1: 00010000 00010000 "env1"
mtd2: 00010000 00010000 "env2"
mtd3: 00620000 00010000 "UBFI1"
mtd4: 00620000 00010000 "UBFI2"
mtd5: 000dd4f0 00010000 "Kernel"
mtd6: 003c3c00 00010000 "RootFileSystem"
mtd7: 00330000 00010000 "APImg"
mtd8: 00050000 00010000 "nvram"

BootLog

This is console output from boot

U-Boot 1.2.0 (May 26 2009 - 10:16:19) PSPU-Boot(BBU) 1.0.1.7 DRAM: 64 MB Spansion S25FL128P flash found Flash: 16 MB In: serial Out: serial Err: serial Press SPACE to abort autoboot in 2 second(s) *** ACTIMAGE = 2, will try to boot UBFI2 stored @0x48660000 ## Executing script at 48660000 ============== Running script ========= *** Running from UBFI2 partition @0x48660000 Load address = 0x486612bc (0x12bc) Kernel address = 0x48661308 (0x1308) kernel size = 0xdd4f0 FS address = 0x4873e7f8 (0xde7f8) FS size = 0x3c3c00 NVRAM offset = 0xfb0000 NVRAM size = 0x50000 *** UBFI2 bootscript executed successfully. Start booting... ## Booting image at 486612bc ... Image Name: Multi Image File Image Type: ARM Linux Multi-File Image (uncompressed) Data Size: 4854012 Bytes = 4.6 MB Load Address: 80a00000 Entry Point: 80a00000 Contents: Image 0: 906480 Bytes = 885.2 kB Image 1: 3947520 Bytes = 3.8 MB Verifying Checksum ... OK OK Starting kernel ... Starting LZMA Uncompression Algorithm. Compressed file is LZMA format. Linux version 2.6.18_pro500 (jimmy@build2.foxconn.com) (gcc version 4.2.0 20070126 (prerelease) (MontaVista 4.2.0-2.0.0.custom 2007-02-12)) #1 PREEMPT Fri Nov 6 11:04:10 CST 2009 CPU: ARMv6-compatible processor [410fb764] revision 4 (ARMv6TEJ), cr=00c538ff Machine: puma5 Ignoring unrecognised tag 0x00000000 Memory policy: ECC disabled, Data cache writethrough Reserved 2048k DSP memory starting from Physical 0x83e00000 CPU0: D VIPT write-back cache CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Real-Time Preemption Support (C) 2004-2006 Ingo Molnar Built 1 zonelists. Total pages: 15872 Kernel command line: root=/dev/mtdblock6 mtdparts=spansion:0x20000(U-Boot)ro,0x10000(env1),0x10000(env2),0x620000@0x40000(UBFI1),0x620000@0x660000(UBFI2),0xdd4f0@0x661308(Kernel),0x3c3c00(RootFileSystem),0x330000@0xc80000(APImg),0x50000@0xfb0000(nvram) console=ttyS0,115200n8 ethaddr0=00:1e:2a:03:87:c0 usbhostaddr=00.00.00.00.00.00 WARNING: experimental RCU implementation. Interrupt controller revision : 4e822100 PID hash table entries: 256 (order: 8, 1024 bytes) Power & Sleep Controller @ 0xd8621000 Initialized [id-0x44822905] Initialized Peripheral Port Remap Register to base : 0x50000000 Puma5 Timer0 initialized Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 62MB = 62MB total Memory: 60244KB available (2036K code, 527K data, 80K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 Off chip memory allocated: 153088 QMgr Init: buffer after alignment: 803c0000 avalanche_ppd_init: PP system initialized successfully. avalanche_ppd_init(494):return code 0x00 SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub musb_hdrc: version 2.2a/db-0.5.1, cppi-dma, host, debug=2 VBUS off(0)-GPIO14(HIGH) musb_hdrc: USB Host mode controller at d3300000 using DMA, IRQ 24 musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected VBUS on(1)-GPIO14(LOW) HIL Core: Profile intrusive has been Loaded. NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -1, 2048 bytes) TCP established hash table entries: 2048 (order: 4, 65536 bytes) TCP bind hash table entries: 1024 (order: 2, 28672 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered squashfs: version 3.3 (2007/10/31) Phillip Lougher squashfs: LZMA suppport for slax.org by jro JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. Initializing Cryptographic API io scheduler noop registered (default) watchdog: TI Avalanche Watchdog Timer: timer margin 42 sec TI LED driver initialized [major=254] Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO map 0x8610f03 mem 0xd8610f03 (irq = 8) is a TI 16550A serial8250: ttyS1 at MMIO map 0x8610e03 mem 0xd8610e03 (irq = 7) is a TI 16550A loop: loaded (max 8 devices) Loading cpgmac driver for puma5 TI CPGMAC_F Linux DDA version 0.1 - CPGMAC_F DDC version 0.2 Cpmac: Installed 1 instances. i2c /dev entries driver Serial Flash [Bus:0 CS:0] : s25fl128p 16384KB, 256 sectors each 64KB 9 cmdlinepart partitions found on MTD device spansion partitions[0] = {.name = U-Boot, .offset = 0x00000000,.size = 0x00020000 (128K) } partitions[1] = {.name = env1, .offset = 0x00020000,.size = 0x00010000 (64K) } partitions[2] = {.name = env2, .offset = 0x00030000,.size = 0x00010000 (64K) } partitions[3] = {.name = UBFI1, .offset = 0x00040000,.size = 0x00620000 (6272K) } partitions[4] = {.name = UBFI2, .offset = 0x00660000,.size = 0x00620000 (6272K) } partitions[5] = {.name = Kernel, .offset = 0x00661308,.size = 0x000dd4f0 (885K) } partitions[6] = {.name = RootFileSystem, .offset = 0x0073e7f8,.size = 0x003c3c00 (3855K) } partitions[7] = {.name = APImg, .offset = 0x00c80000,.size = 0x00330000 (3264K) } partitions[8] = {.name = nvram, .offset = 0x00fb0000,.size = 0x00050000 (320K) } Creating 9 MTD partitions on "spansion": 0x00000000-0x00020000 : "U-Boot" 0x00020000-0x00030000 : "env1" 0x00030000-0x00040000 : "env2" 0x00040000-0x00660000 : "UBFI1" 0x00660000-0x00c80000 : "UBFI2" 0x00661308-0x0073e7f8 : "Kernel" mtd: partition "Kernel" doesn't start on an erase block boundary -- force read-only 0x0073e7f8-0x00b023f8 : "RootFileSystem" mtd: partition "RootFileSystem" doesn't start on an erase block boundary -- force read-only 0x00c80000-0x00fb0000 : "APImg" 0x00fb0000-0x01000000 : "nvram" Serial Flash [Bus:0 CS:1] : No device found ti_spi.0: AVALANCHE SPI Controller driver at 0xd8612500 (irq = 0) ti_codec_spi.0: TI Codec SPI Controller driver at 0xd86040c8 (irq = 0) usbmon: debugfs is not available Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver IPv4 over IPv4 tunneling driver TCP bic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 VFS: Mounted root (squashfs filesystem) readonly. Freeing init memory: 80K init started: BusyBox v1.4.2 (2009-11-06 11:05:28 CST) multi-call binary init started: BusyBox v1.4.2 (2009-11-06 11:05:28 CST) multi-call binary Starting pid 141, console /dev/tts/0: '/bin/sh' ======================================================== TI U12C121T10 release 1.4.1.19 Build date: Friday, November 06 2009, 11:05:53 Copyright (c) 2006 - 2008 Texas Instruments Incorporated ======================================================== ATHR_PORT0_CTRL: 0x6004 ATHR_PORT1_CTRL: 0x6004 ATHR_PORT2_CTRL: 0x6004 ATHR_PORT3_CTRL: 0x6004 ATHR_PORT4_CTRL: 0x6004 ATHR_PORT5_CTRL: 0x6004 ATHR_PORT0_VLAN: 0x3e0001 ATHR_PORT1_VLAN: 0x3d0001 ATHR_PORT2_VLAN: 0x3b0001 ATHR_PORT3_VLAN: 0x370001 ATHR_PORT4_VLAN: 0x2f0001 ATHR_PORT5_VLAN: 0x1f0001 Autoconfiguration disabled for eth0 Thu Jan 1 00:00:03 UTC 1970 Recover the switch ...WRITE: address = 0x03000008, value = 0x012E9B66 WRITE: address = 0x03000100, value = 0x0000007E WRITE: address = 0x03000600, value = 0x0000007E WRITE: address = 0x03000200, value = 0x00000200 WRITE: address = 0x03000300, value = 0x00000200 WRITE: address = 0x03000400, value = 0x00000200 WRITE: address = 0x03000500, value = 0x00000200 WRITE: address = 0x03000104, value = 0x00004204 WRITE: address = 0x03000204, value = 0x00006104 WRITE: address = 0x03000304, value = 0x00006104 WRITE: address = 0x03000404, value = 0x00006104 WRITE: address = 0x03000504, value = 0x00006104 WRITE: address = 0x03000604, value = 0x00006104 WRITE: address = 0x03000108, value = 0x003E0003 WRITE: address = 0x03000208, value = 0x001D0001 WRITE: address = 0x03000308, value = 0x001B0001 WRITE: address = 0x03000408, value = 0x00170001 WRITE: address = 0x03000508, value = 0x000F0001 WRITE: address = 0x03000608, value = 0x00010002 WRITE: address = 0x0300002C, value = 0x003F003F WRITE: address = 0x03000030, value = 0x21F005F2 PING 192.168.101.254 (192.168.101.254): 56 data bytes --- 192.168.101.254 ping statistics --- 1 packets transmitted, 0 packets received, 100% packet loss WRITE: address = 0x03000104, value = 0x00006004 WRITE: address = 0x03000204, value = 0x00006004 WRITE: address = 0x03000304, value = 0x00006004 WRITE: address = 0x03000404, value = 0x00006004 WRITE: address = 0x03000504, value = 0x00006004 WRITE: address = 0x03000604, value = 0x00006004 WRITE: address = 0x03000001, value = 0x00000104 WRITE: address = 0x03000001, value = 0x00000204 WRITE: address = 0x03000001, value = 0x00000304 WRITE: address = 0x03000001, value = 0x00000404 WRITE: address = 0x03000001, value = 0x00000504 WRITE: address = 0x03000001, value = 0x00000604 PASS Daemon Successfully forked (pid: 288) ===== Wait for AP ready ===== ....Rx Channel TearDown Descriptor Found 803d8b00 numBD = 65 Tx Channel Teardown Descriptor found! 803d8020 Using DOCSIS Initialization process parameters: -ds_channels 4 -us_channels 4 -debug_options 1048576 Using DOCSIS MAC Driver parameters: -1st_freq 294000000 Using DOCSIS MAC Manager parameters: -x -m Starting pid 385, console /dev/tts/0: '/bin/sh' BusyBox v1.4.2 (2009-11-06 11:05:28 CST) Built-in shell (ash) Enter 'help' for a list of built-in commands. # pcd: Starting TI Process Control Daemon. pcd: Loaded 76 rules. pcd: Initialization complete. pcd: Starting process /usr/sbin/watchdog_rt (Rule SYSTEM_WATCHDOG). TI Watchdog-RT daemon started <kick interval = 10 seconds> pcd: Starting process /usr/sbin/logger (Rule SYSTEM_LOGGER). pcd: Rule SYSTEM_WATCHDOG: Success (Process /usr/sbin/watchdog_rt (386)). TI Logger: Init complete pcd: Rule SYSTEM_LOGGER: Success (Process /usr/sbin/logger (387)). pcd: Starting process /usr/sbin/gptimer (Rule SYSTEM_GPTIMER). pcd: Rule SYSTEM_GPTIMER: Success (Process /usr/sbin/gptimer (388)). pcd: Rule SYSTEM_LASTRULE: Success. pcd: Starting process /bin/sh (Rule BBU_INITDRV). BBU Kernel module - installing <4>BbuIsRev2: rev 1 BBU Kernel module installed - 0 pcd: Rule BBU_INITDRV: Success (Process /bin/sh (390)). pcd: Starting process /usr/sbin/bbusm (Rule BBU_SM). pcd: Rule BBU_SM: Success (Process /usr/sbin/bbusm (401)). pcd: Starting process /bin/sh (Rule BBU_DLMRMMOD). pcd: Rule BBU_LASTRULE: Success. pcd: Starting process echo (Rule DOCSIS_APPRUN). pcd: Rule DOCSIS_APPRUN: Success (Process echo (404)). pcd: Starting process /usr/sbin/docsis_init_once (Rule DOCSIS_INITONCE). pcd: Starting process insmod (Rule DOCSIS_BRIDGE). Dbridge MDF control init done pcd: Rule DOCSIS_BRIDGE: Success (Process insmod (406)). pcd: Starting process insmod (Rule DOCSIS_CNI). pcd: Rule DOCSIS_CNI: Success (Process insmod (411)). pcd: Rule DOCSIS_INITONCE: Success (Process /usr/sbin/docsis_init_once (405)). pcd: Starting process /usr/sbin/ledd (Rule DOCSIS_LED). pcd: Rule DOCSIS_LED: Success (Process /usr/sbin/ledd (416)). pcd: Starting process insmod (Rule DOCSIS_HALVLYNQ). pcd: Starting process /usr/sbin/cm_status (Rule DOCSIS_CMSTATUS). VLYNQ driver initialization complete. pcd: Rule DOCSIS_HALVLYNQ: Success (Process insmod (417)). pcd: Starting process insmod (Rule DOCSIS_SOCIFDRV). pcd: Rule DOCSIS_CMSTATUS: Success (Process /usr/sbin/cm_status (418)). pcd: Rule DOCSIS_SOCIFDRV: Success (Process insmod (421)). pcd: Starting process mknod (Rule DOCSIS_MKNODSOCIFDRV). pcd: Rule DOCSIS_MKNODSOCIFDRV: Success (Process mknod (423)). pcd: Starting process insmod (Rule DOCSIS_MNG). pcd: Rule DOCSIS_MNG: Success (Process insmod (424)). pcd: Starting process mknod (Rule DOCSIS_MKNODMNG). pcd: Starting process insmod (Rule DOCSIS_KINTR). pcd: Rule DOCSIS_MKNODMNG: Success (Process mknod (426)). pcd: Starting process insmod (Rule DOCSIS_FILTERCLASS). pcd: Rule DOCSIS_KINTR: Success (Process insmod (427)). pcd: Starting process /usr/sbin/hal_event_mbox (Rule DOCSIS_HALEVENTMBOX). pcd: Starting process /usr/sbin/hal_cmd_mbox (Rule DOCSIS_HALCMDMBOX). pcd: Rule DOCSIS_HALCMDMBOX: Success (Process /usr/sbin/hal_cmd_mbox (437)). pcd: Rule DOCSIS_FILTERCLASS: Success (Process insmod (434)). pcd: Starting process /bin/sh (Rule DOCSIS_FCDEV). pcd: Rule DOCSIS_HALEVENTMBOX: Success (Process /usr/sbin/hal_event_mbox (436)). pcd: Starting process /usr/sbin/mlx (Rule DOCSIS_MLX). pcd: Rule DOCSIS_MLX: Success (Process /usr/sbin/mlx (441)). pcd: Rule DOCSIS_FCDEV: Success (Process /bin/sh (439)). pcd: Starting process /usr/sbin/hal_tuner_mgr (Rule DOCSIS_HALTUNERMGR). pcd: Starting process /usr/sbin/dbridge_init (Rule DOCSIS_DBRIDGEINIT). pcd: Rule DOCSIS_HALTUNERMGR: Success (Process /usr/sbin/hal_tuner_mgr (452)). Ingress Hook on eth0 Dbridge Init SUCSESS Autoconfiguration disabled for br0 pcd: Rule DOCSIS_HALREADY: SucceHAL_MacDsUnicastDataFilterAdd: system_rev = 1 ss. pcd: Starting process /usr/Autoconfiguration disabled for lbr0 sbin/qos_dsx_sm (Rule DOCSIS_QOSDSXSM). ATHR_PORT0_CTRL: 0x6004 pcd: Starting process /usr/sbin/dispatcher (Rule DOCSIS_DISPATCHER). pcd: Starting process /usr/sbin/bpi_auth (Rule DOCSIS_BPIAUTH). ATHR_PORT1_CTRL: 0x6004 ATHR_PORT2_CTRL: 0x6004 ATHR_PORT3_CTRL: 0x6004 ATHR_PORT4_CTRL: 0x6004 ATHR_PORT5_CTRL: 0x6004 ATHR_PORT0_VLAN: 0x3e0003 ATHR_PORT1_VLAN: 0x1d0001 ATHR_PORT2_VLAN: 0x1b0001 ATHR_PORT3_VLAN: 0x170001 ATHR_PORT4_VLAN: 0xf0001 ATHR_PORT5_VLAN: 0x10002 Autoconfiguration disabled for eth0 netlink_open: initialized fd 6 pcd: Rule DOCSIS_DISPATCHER: Success (Process /usr/sbin/dispatcher (459)). pcd: Starting process /usr/sbin/docsis_mac_driver (Rule DOCSIS_MACDRIVER). HAL_MacDsUnicastDataFilterAdd: system_rev = 1 Autoconfiguration disabled for lan0 Autoconfiguration disabled for wan0 HAL_MacDsUnicastDataFilterAdd: system_rev = 1 Autoconfiguration disabled for cni0 pcd: Rule DOCSIS_DBRIDGEINIT: Success (Process /usr/sbin/dbridge_init (453)). pcd: Starting process /bin/sh (Rule FOXCONN_SWITCH_CHK). pcd: Starting process /usr/foxconn/bin/push_buttond (Rule FOXCONN_PUSH_BUTTOND). pcd: Starting process /bin/sh (Rule FOXCONN_INIT_SW). pcd: Starting process /usr/foxconn/bin/evtMonitor (Rule FOXCONN_EVT_MONITOR). pcd: Starting process /usr/sbin/snmp_agent_cm (Rule DOCSIS_SNMPAGENT). pcd: Starting process /bin/sh (Rule DOCSIS_DBRIDGEMDFINIT). pcd: Rule DOCSIS_QOSDSXSM: Success (Process /usr/sbin/qos_dsx_sm (458)). pcd: Rule FOXCONN_EVT_MONITOR: Success (Process /usr/foxconn/bin/evtMonitor (475)). pcd: Rule FOXCONN_PUSH_BUTTOND: Success (Process /usr/foxconn/bin/push_buttond (473)). pcd: Rule FOXCONN_SWITCH_CHK: Success (Process /bin/sh (472)). pcd: Rule DOCSIS_BPIAUTH: Success (Process /usr/sbin/bpi_auth (460)). pcd: Starting process /usr/sbin/bpi_tek (Rule DOCSIS_BPITEK). pcd: Starting process /usr/sbin/bpi_sa_map (Rule DOCSIS_BPISAMAP). Polling interval is 250, 250 Reset default time is 5000, 5000 read factory mode: routing isFactoryMode:0 pcd: Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR4). pcd: Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR3). pcd: Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR2). pcd: Starting process /usr/sbin/downstream_manager (Rule DOCSIS_DSMNGR1). WRITE: address = 0x03000104, value = 0x00004204 pcd: Rule DOCSIS_DBRIDGEMDFINIT: Success (Process /bin/sh (477)). pcd: Starting process insmod (Rule DOCSIS_PP). WRITE: address = 0x03000204, value = 0x00006104 WRITE: address = 0x03000304, value = 0x00006104 WRITE: address = 0x03000404, value = 0x00006104 pcd: Rule DOCSIS_BPISAMAP: Success (Process /usr/sbin/bpi_sa_map (481)). WRITE: address = 0x03000504, value = 0x00006104 WRITE: address = 0x03000604, value = 0x00006104 WRITE: address = 0x03000108, value = 0x003E0003 WRITE: address = 0x03000208, value = 0x001D0001 WRITE: address = 0x03000308, value = 0x001B0001 pcd: Rule DOCSIS_BPITEK: Success (Process /usr/sbin/bpi_tek (480)). WRITE: address = 0x03000408, value = 0x00170001 WRITE: address = 0x03000508, value = 0x000F0001 WRITE: address = 0x03000608, value = 0x00010002 WRITE: address = 0x0300002C, value = 0x003F003F WRITE: address = 0x03000030, value = 0x21F005F2 pcd: Rule FOXCONN_INIT_SW: Success (Process /bin/sh (474)). pcd: Starting process /sbin/utelnetd (Rule FOXCONN_TELNETD). pcd: Rule FOXCONN_TELNETD: Success (Process /sbin/utelnetd (539)). Create DOCSIS Packet Processor counters char device done Init Docsis Packet Processor counters DB done. DOCSIS Packet Processor counters control init done DOCSIS Packet Processor control init done pcd: Rule DOCSIS_PP: Success (Process insmod (513)). pcd: Starting process /bin/sh (Rule DOCSIS_PPDEV). pcd: Rule DOCSIS_DSMNGR2: Success (Process /usr/sbin/downstream_manager (505)). pcd: Rule DOCSIS_DSMNGR4: Success (Process /usr/sbin/downstream_manager (501)). pcd: Rule DOCSIS_DSMNGR3: Success (Process /usr/sbin/downstream_manager (502)). pcd: Rule DOCSIS_DSMNGR1: Success (Process /usr/sbin/downstream_manager (506)). pcd: Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR1). pcd: Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR2). pcd: Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR3). pcd: Starting process /usr/sbin/upstream_manager (Rule DOCSIS_USMNGR4). SNMPA_CreateSocketEntry : type 0, addr = 0, port = 0, ifname = /var/tmp/cm_snmp_ctrl List = (nil) Cntl Entry created telnetd: starting port: 23; interface: any; login program: /bin/login PGA Type: MT1570 resetEnabled:1 pcd: Rule DOCSIS_USMNGR3: Success (Process /usr/sbin/upstream_manager (555)). pcd: Rule DOCSIS_USMNGR4: Success (Process /usr/sbin/upstream_manager (556)). pcd: Rule DOCSIS_USMNGR1: Success (Process /usr/sbin/upstream_manager (553)). pcd: Rule DOCSIS_PPDEV: Success (Process /bin/sh (541)). pcd: Rule DOCSIS_USMNGR2: Success (Process /usr/sbin/upstream_manager (554)). pcd: Rule DOCSIS_MACDRIVER: Success (Process /usr/sbin/docsis_mac_driver (463)). Unloading the BBU DLM BBU module is down! pcd: Rule BBU_DLMRMMOD: Success (Process /bin/sh (403)). pcd: Rule DOCSIS_SNMPAGENT: Success (Process /usr/sbin/snmp_agent_cm (476)). SNMPA_CreateSocketEntry : type 1, addr = c0a86501, port = 161, ifname = lan0 List = 0x69750 SNMPA_CreateSocketEntry : type 1, addr = c0a86501, port = 162, ifname = lan0 List = 0x69750 pcd: Starting process /usr/sbin/eventmgr_cm (Rule DOCSIS_EVENTMNGR). pcd: Rule DOCSIS_EVENTMNGR: Success (Process /usr/sbin/eventmgr_cm (1014)). pcd: Starting process /usr/sbin/docsis_mac_manager (Rule DOCSIS_MACMANAGER). pcd: Rule DOCSIS_MACMANAGER: Success (Process /usr/sbin/docsis_mac_manager (1015)). pcd: Rule DOCSIS_LASTRULE: Success. pcd: Starting process insmod (Rule PACM_MTANI). mtani: Network interface initialized successfully RTNL: assertion failed at net/ipv4/devinet.c (987) RTNL: assertion failed at net/ipv6/addrconf.c (2170) RTNL: assertion failed at net/ipv6/addrconf.c (1644) RTNL: assertion failed at net/ipv6/addrconf.c (456) RTNL: assertion failed at net/ipv6/addrconf.c (367) Autoconfiguration disabled for esafe0 mtani: Network interface registered successfully pcd: Rule PACM_MTANI: Success (Process insmod (1016)). pcd: Starting process /usr/sbin/pacm_init (Rule PACM_INIT). Autoconfiguration disabled for mta0 HAL_MacDsUnicastDataFilterAdd: system_rev = 1 Production config saved to NVRAMSTA MAC initialized to 00:26:F2:66:29:51PACM - Exec PACM_Prov_DbInit PACM - Exec PACM_MSM_DbInit PACM - Exec Security_InitDataBase PACM - Exec SnmpDB_Init pcd: Rule PACM_INIT: Success (Process /usr/sbin/pacm_init (1020)). pcd: Starting process insmod (Rule VOICE_INSMXPMOD). pcd: Starting process /usr/sbin/pacm_vendor_app (Rule PACM_VENDORAPP). pcd: Starting process /usr/sbin/pacm_snmp_agent (Rule PACM_SNMP). pcd: Starting process /usr/sbin/pacm_security (Rule PACM_SECURITY). pcd: Starting process /usr/sbin/pacm_event_mgr (Rule PACM_EVENTMGR). pcd: Starting process /usr/sbin/pacm_doim (Rule PACM_DOIM). pcd: Rule PACM_VENDORAPP: Success (Process /usr/sbin/pacm_vendor_app (1026)). MXP_TMR: Calibrating MXP Timer... Ticks/sec=200 Starting MXP timer MXP module loaded pcd: Rule VOICE_INSMXPMOD: Success (Process insmod (1025)). pcd: Starting process insmod (Rule VOICE_INSMXPMEM). pcd: Rule PACM_EVENTMGR: Success (Process /usr/sbin/pacm_event_mgr (1029)). MXP memory module loaded pcd: Rule PACM_DOIM: Success (Process /usr/sbin/pacm_doim (1030)). pcd: Rule VOICE_INSMXPMEM: Success (Process insmod (1038)). pcd: Starting process insmod (Rule VOICE_INSDSPMOD). Processing configuration file... Found command: sysdescr eMTA SNMP Agent Found command: syscontact NETGEAR Found command: sysLocation Santa Clara, CA 95054 Found command: read-community public Found command: write-community private Found command: trap-community SNMP-trap Found command: nv-file /etc/snmp_mta_nv.txt Hit EOF of config file ****HOST INFORMATION**** sysDescr is "eMTA SNMP Agent" sysContact is "NETGEAR" sysLocation is "Santa Clara, CA 95054" System Boot time was Thu Jan 1 00:00:44 1970 System object identifier has 14 components: 0.0.0.0.0.0.0.0.0.0.0.0.0.0. ****SNMP AGENT INFORMATION**** Community names: Read: public Write: private Trap: SNMP-trap nv-file: /etc/snmp_mta_nv.txt SNMPA_CreateSocketEntry : type 0, addr = 0, port = 0, ifname = /var/tmp/mta_snmp_ctrl List = (nil) Cntl Entry created pcd: Rule PACM_SECURITY: Success (Process /usr/sbin/pacm_security (1028)). 57: Disabling PUMAV DSPSS 60: Taking PUMAV DSPSS IN RESET HW_DSP module loaded pcd: Rule VOICE_INSDSPMOD: Success (Process insmod (1041)). pcd: Starting process insmod (Rule VOICE_INSTELEHAL). TIUHAL: Finished TDM configuration spi_tid_probe: Setting TID template TIUHAL using DOCSIS clock source pcd: Rule VOICE_INSTELEHAL: Success (Process insmod (1063)). pcd: Starting process udevstart (Rule VOICE_UDEVSTART). pcd: Rule VOICE_UDEVSTART: Success (Process udevstart (1073)). pcd: Starting process /usr/sbin/ggncs (Rule VOICE_GGAPP). Initializing signal_handler tcb_alloc: task id=1,name=mxproot,busy=1 tcb_alloc: task id=2,name=XSPY,busy=1 tcb_alloc: task id=3,name=XTELNET,busy=1 tcb_alloc: task id=4,name=ROOT,busy=1 >>>> rootInit <<<<< Creating Golden Gateway application... Registered with TIUHAL version 3tcb_alloc: task id=5,name=NWIF01,busy=1 tcb_alloc: task id=6,name=DQMM,busy=1 TID(M) 0 is VE88276PTC014 num_hw_tcids = 2 num of TIDS=1 VP880_236: SLIC termination type 0 tiuhw_setup_chipselect: cs for tcid 2 = 4 fxo: 0 Loading dsp image: /lib/dspimage.ld tcb_alloc: task id=7,name=DLMM,busy=1 tcb_alloc: task id=8,name=ISU,busy=1 tcb_alloc: task id=9,name=VIM,busy=1 tcb_alloc: task id=10,name=CCU,busy=1 tcb_alloc: task id=11,name=RTCP,busy=1 tcb_alloc: task id=12,name=PMA,busy=1 tcb_alloc: task id=13,name=DEX,busy=1 DSPMOD query DSP address syscall: DSP Start address = 0x83E00000 HW_DSP DSP External Config Register set to: 0x83000000, Start: 0x83E00000 57: Disabling PUMAV DSPSS 60: Taking PUMAV DSPSS IN RESET DSP external memory mapped to 0x04484000 (User Sp) = 0x83E00000 (Kernel Sp) dimhw_init_dsp: dpr_base mapped to 0x03684000 (User sp) tcb_alloc: task id=14,name=DCMM,busy=1 tcb_alloc: task id=15,name=CPMU,busy=1 tcb_alloc: task id=16,name=xGCP,busy=1 tcb_alloc: task id=17,name=NMM,busy=1 tcb_alloc: task id=18,name=VOIMFE,busy=1 tcb_free: task id=4, name=ROOT FXS FXR = 16 hw_config: tcid: 0 onhook volts = 48, offhook current = 26, country = 1 hw_config: tcid: 0 ringer type: 1 frequency: 20 amplitude: 66 offset: 0 Attempting to delete TCB: 4 XtDelete called lmxp_tcb_free called for 4 pcd: Rule VOICE_GGAPP: Success (Process /usr/sbin/ggncs (1074)). Received request for gain settings for TCID: 0, rx = -4, tx = -2 pcd: Rule VOICE_LASTRULE: Success. INT ENABLE 0 OK, int_mask 9c 9c hw_config: tcid: 1 onhook volts = 48, offho57: Disabling PUMAV DSPSS 60: Taking PUMAV DSPSS IN RESET ok current = 26, country = 1 hw_config: tcid: 1 ringer type: 1 frequency: 20 amplitude: 66 offset: 0 Received request for gain settings for TCID: 1, rx = -4, tx = -2 INT ENABLE 1 OK, int_mask 9c 9c [ERROR]: 0000000646 - NCSDK Version: 2.4.4 [ERROR]: 0000000646 - ROOT:Number of tcids in the system 2: 2: 2: 6 [ERROR]: 0000000646 - MAS Version: 2.4.4(Build 15) [ERROR]: 0000000646 - Following features compiled out of the build: [ERROR]: 0000000646 - DIM_DNLD_PAGED_BOOT [ERROR]: 0000000646 - DIM_DNLD_DIRECT [ERROR]: 0000000646 - DIM_DNLD_MSG [ERROR]: 0000000646 - DIM_DNLD_RST_DIRECT [ERROR]: 0000000646 - DIM_CHAN_IF [ERROR]: 0000000646 - ANNC_IF [ERROR]: 0000000646 - DIM_RTCP_IF [ERROR]: 0000000646 - DIM_SIG_IF [ERROR]: 0000000646 - DIM_AUDIO_IF [ERROR]: 0000000646 - DIM_AFE_IF [ERROR]: 0000000646 - DIM_LOMGR_GEN_FIFO [ERROR]: 0000000646 - DIM_LOMGR_CHN_FIFO [ERROR]: 0000000646 - DIM_LOMGR_MAIL_BOX [ERROR]: 0000000646 - PROTO_AAL2 [ERROR]: 0000000646 - PROTO_CLRDT [ERROR]: 0000000646 - PROTO_MODEM [ERROR]: 0000000646 - DIM_3PROC [ERROR]: 0000000646 - DIM_DETAILED_SPY [ERROR]: 0000000646 - Following features not defined in build and have been enabled [ERROR]: 0000000646 - by default; REVIEW to remove potential unecessary code: [ERROR]: 0000000646 - All features are accounted for!!! [ERROR]: 0000000646 - ISU: isu_module_init isu_event_base 0x0, task 0x00000000 [ERROR]: 0000000646 - ISU: isu_create 0x00000008 queue 1 [ERROR]: 0000000646 - CCU: ccu_module_init ccu_event_base 0x0, task 0x00000000 [ERROR]: 0000000646 - CCU: ccu_create 0x0000000A queue 1 watchdog timer 2 [ERROR]: 0000000646 - DIM: status_request_period out of range [20 - 10000] [ERROR]: 0000000646 - DIM: status_request_period set to default [1000] [ERROR]: 0000000646 - TIU max tcids = 2, poll mode = 0, poll period = 5 [ERROR]: 0000000646 - TIU: Polling period must be multiple of 2 msec [ERROR]: 0000000674 - DIM: 0:*, dimp_find_and_init_lo_mgr(). max simple msg len (128) < sizeof(mgb_t)(130) pcd: Rule PACM_SNMP: Success (Process /usr/sbin/pacm_snmp_agent (1027)). pcd: Rule PACM_INITDONE: Success. pcd: Starting process /usr/sbin/pacm_mta_control (Rule PACM_MTACTRL). pcd: Rule PACM_MTACTRL: Success (Process /usr/sbin/pacm_mta_control (1101)). pcd: Rule PACM_LASTRULE: Success. pcd: Starting process /bin/sh (Rule FOXCONN_INIT_VOIP_SETTI). pcd: Rule FOXCONN_INIT_VOIP_SETTI: Success (Process /bin/sh (1102)). ############## voip settings ################## Console redirected to an external telnet connection ÿýÿý!ÿûÿûTexas Instruments Inc. 2007 Golden Gateway Remote Command Processor MXP>set xgcp country 14 Setting country Denmark ... nmm_ring_cadence_table Rin57: Enabling PUMAV DSPSS 60: Taking PUMAV DSPSS OUT of RESET gCadence(10) : duration = -1, repeat = 0 pulse(0) : 15 on 150 off country_ring_params RingCadence(10) : duration = -1, repeat = 0 pulse(0) : 15 on 150 off [ERROR]: 0000000891 - NWIF: DQOS is set to NORMAL [ERROR]: 0000000891 - XGCP CAIF: OUR IP UNKNOWN.. CAIF NOT UP [ERROR]: 0000000896 - DIM: , CHECKSUM=8575 [ERROR]: 0000000897 - DIM: 0:*, Core Download complete! [ERROR]: 0000000901 - DIM: 0:*, CONFIG has been received! [ERROR]: 0000000901 - DIM: 0:*, dimp_find_and_init_lo_mgr(). max simple msg len (128) < sizeof(mgb_t)(130) [ERROR]: 0000000903 - DSPA: DSP 0,Image 0:Download done! FcUtils_AddSysInterface: Failed to get net device struct for usb0 hw_config: tcid: 0 onhook volts = 48, offhook current = 26, country = 1 hw_config: tcid: 0 ringer type: 1 frequency: 25 amplitude: 66 offset: 0 INT ENABLE 0 OK, int_mask 9c 9c Received request for gain settings for TCID: 0, rx = 0, tx = 0 INT ENABLE 0 OK, int_mask 9c 9c hw_config: tcid: 1 onhook volts = 48, offhook current = 26, country = 1 hw_config: tcid: 1 ringer type: 1 frequency: 25 amplitude: 66 offset: 0 INT ENABLE 1 OK, int_mask 9c 9c Received request for gain settings for TCID: 1, rx = 0, tx = 0 INT ENABLE 1 OK, int_mask 9c 9c Connection closed OK MXP> #


Tags

inbox/toh/netgear.cg3200.txt · Last modified: 2015/12/14 16:07 by tmomas