User Tools

Site Tools


inbox:toh:netgear.cg3200

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
inbox:toh:netgear.cg3200 [2014/03/02 18:45]
inbox:toh:netgear.cg3200 [2015/12/14 16:07] (current)
tmomas
Line 1: Line 1:
 +====== Netgear CG3200 ======
 +Wireless Cable Voice Gateway used by the danish ISP "​YouSee"​.
  
 +====== Hardware Highlights ======
 +
 +^ CPU ^ Ram ^ Flash ^ Modem ^ Network ^ USB ^ Serial ^ Pots ^ JTag ^
 +| ARMv6-compatible processor rev 4 (v6b) | 64MiB | 16MiB | Docsis 3.0 | 4 x 1| Yes | Yes | 2 | ? |
 +
 +====== Hardware ======
 +
 +===== Info =====
 +
 +| **Architecture:​** ARMv6                  |
 +| **Vendor:** TI/​Intel ​                    |
 +| **Bootloader:​** PSPU-Boot(BBU) 1.0.1.7 ​  |
 +| **System-On-Chip:​** Puma5 TNETC4800 ​     |
 +| **CPU Speed:** 400 MHz                   |
 +| **Flash-Chip:​** Spansion S25FL128P ​      |
 +| **Flash size:** 16 MiB                   |
 +| **RAM:** 64 MiB                          |
 +| **Wireless:​** mini-PCI ​                  |
 +| **Ethernet:​** 4 x 10/​100/​1000 ​           |
 +| **USB:** Yes                             |
 +| **Serial:** [[#​Serial|Yes]] ​             |
 +| **JTAG:** [[#JTAG| ? ]]                  |
 +
 +===== Photos =====
 +Model Number
 +
 +//Front://
 +
 +**Photo of front**
 +
 +//Back://
 +
 +**Photo of back**
 +
 +===== Opening the case =====
 +**Note:** This will void your warranty!
 +
 +  *To remove the cover simply unscrew 6 screws in bottom of device. ​
 +  *There are four screws under the rubber feets.
 +
 +//Main PCB//
 +
 +**Photo of PCB (coming as soon i learn howto upload)**
 +
 +===== Serial =====
 +
 +This model has an 6-pin header (J6) that exposes a 3.3V serial port. Pins are listed below:
 +| Pin 1   | 3,3V   |
 +| Pin 2   | RxD    |
 +| Pin 3   | nc     |
 +| Pin 4   | nc     |
 +| Pin 5   | TxD    |
 +| Pin 6   | GND    |
 +
 +Serial connection parameters are : 115200,8N1
 +
 +===== JTAG =====
 +
 +
 +===== Conectors =====
 +
 +| F-connector ​  | WAN port     |
 +| 4 * RJ45      | LAN          |
 +| 2 * RJ11      | Phone pots   |
 +| 1 * USB       ​| ​             |
 +
 +===== Buttons =====
 +
 +The device has 3 buttons, the reset i located under the device.
 +
 +^ BUTTON ​    ^ Event   ^
 +| Reset      | reset   |
 +| wifi       ​| ​        |
 +| security ​  ​| ​        |
 +
 +====== Other Info ======
 +=== ifconfig ===
 +<​code>​
 +br0       Link encap:​Ethernet ​ HWaddr 00:​1E:​2A:​03:​87:​C0
 +          UP BROADCAST RUNNING MULTICAST ​ MTU:​1500 ​ Metric:1
 +          RX packets:1 errors:0 dropped:0 overruns:0 frame:0
 +          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
 +          collisions:​0 txqueuelen:​0
 +          RX bytes:28 (28.0 B)  TX bytes:0 (0.0 B)
 +
 +cni0      Link encap:​Ethernet ​ HWaddr 00:​50:​F1:​80:​00:​00
 +          UP BROADCAST RUNNING PROMISC MULTICAST ​ MTU:​1500 ​ Metric:1
 +          RX packets:3 errors:0 dropped:0 overruns:0 frame:0
 +          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
 +          collisions:​0 txqueuelen:​1000
 +          RX bytes:60 (60.0 B)  TX bytes:0 (0.0 B)
 +
 +esafe0 ​   Link encap:​Ethernet ​ HWaddr 00:​00:​00:​00:​00:​00
 +          UP BROADCAST RUNNING MULTICAST ​ MTU:​1500 ​ Metric:1
 +          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
 +          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
 +          collisions:​0 txqueuelen:​1000
 +          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
 +
 +eth0      Link encap:​Ethernet ​ HWaddr 00:​1E:​2A:​03:​87:​C0
 +          UP BROADCAST RUNNING PROMISC MULTICAST ​ MTU:​1500 ​ Metric:1
 +          RX packets:136 errors:0 dropped:0 overruns:0 frame:0
 +          TX packets:128 errors:0 dropped:0 overruns:0 carrier:0
 +          collisions:​0 txqueuelen:​1000
 +          RX bytes:10633 (10.3 KiB)  TX bytes:29756 (29.0 KiB)
 +          Base address:​0xe000
 +
 +lan0      Link encap:​Ethernet ​ HWaddr 00:​18:​4D:​FF:​FF:​04
 +          inet addr:​192.168.101.1 ​ Bcast:​192.168.101.255 ​ Mask:​255.255.255.0
 +          inet6 addr: fe80::​218:​4dff:​feff:​ff04/​64 Scope:Link
 +          UP BROADCAST RUNNING PROMISC MULTICAST ​ MTU:​1500 ​ Metric:1
 +          RX packets:48 errors:0 dropped:0 overruns:0 frame:0
 +          TX packets:52 errors:0 dropped:0 overruns:0 carrier:0
 +          collisions:​0 txqueuelen:​1000
 +          RX bytes:4595 (4.4 KiB)  TX bytes:3688 (3.6 KiB)
 +
 +lbr0      Link encap:​Ethernet ​ HWaddr 00:​50:​F1:​00:​00:​00
 +          UP BROADCAST RUNNING MULTICAST ​ MTU:​1500 ​ Metric:1
 +          RX packets:45 errors:0 dropped:0 overruns:0 frame:0
 +          TX packets:45 errors:0 dropped:0 overruns:0 carrier:0
 +          collisions:​0 txqueuelen:​1000
 +          RX bytes:3150 (3.0 KiB)  TX bytes:4547 (4.4 KiB)
 +
 +lo        Link encap:Local Loopback
 +          inet addr:​127.0.0.1 ​ Mask:​255.0.0.0
 +          inet6 addr: ::1/128 Scope:Host
 +          UP LOOPBACK RUNNING ​ MTU:​16436 ​ Metric:1
 +          RX packets:42 errors:0 dropped:0 overruns:0 frame:0
 +          TX packets:42 errors:0 dropped:0 overruns:0 carrier:0
 +          collisions:​0 txqueuelen:​0
 +          RX bytes:3180 (3.1 KiB)  TX bytes:3180 (3.1 KiB)
 +
 +mta0      Link encap:​Ethernet ​ HWaddr 00:​26:​F2:​66:​29:​51
 +          UP BROADCAST RUNNING ​ MTU:​1500 ​ Metric:1
 +          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
 +          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
 +          collisions:​0 txqueuelen:​1000
 +          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
 +</​code>​
 +
 +=== /​proc/​devices ===
 +<​code>​
 +Character devices:
 +  1 mem
 +  4 ttyS
 +  5 /dev/tty
 +  5 /​dev/​console
 +  5 /dev/ptmx
 + 10 misc
 + 32 docsis_mng
 + 36 soc_if_driver
 + 89 i2c
 + 90 mtd
 +128 ptm
 +136 pts
 +180 usb
 +189 usb_device
 +249 docsis_pp_counters
 +250 docsis_fltr_class
 +251 DOCINT
 +252 docsis_dbridge_mdf
 +254 led
 +
 +Block devices:
 +  7 loop
 + 31 mtdblock
 +</​code>​
 +
 +=== /proc/mtd ===
 +<​code>​
 +dev:    size   ​erasesize ​ name
 +mtd0: 00020000 00010000 "​U-Boot"​
 +mtd1: 00010000 00010000 "​env1"​
 +mtd2: 00010000 00010000 "​env2"​
 +mtd3: 00620000 00010000 "​UBFI1"​
 +mtd4: 00620000 00010000 "​UBFI2"​
 +mtd5: 000dd4f0 00010000 "​Kernel"​
 +mtd6: 003c3c00 00010000 "​RootFileSystem"​
 +mtd7: 00330000 00010000 "​APImg"​
 +mtd8: 00050000 00010000 "​nvram"​
 +</​code>​
 +
 +=== BootLog ===
 +This is console output from boot
 +<WRAP bootlog>
 +<​nowiki>​U-Boot 1.2.0 (May 26 2009 - 10:16:19)
 +PSPU-Boot(BBU) 1.0.1.7
 +
 +DRAM:  64 MB
 +Spansion S25FL128P flash found
 +Flash: 16 MB
 +In:    serial
 +Out:   ​serial
 +Err:   ​serial
 +Press SPACE to abort autoboot in 2 second(s)
 +*** ACTIMAGE = 2, will try to boot UBFI2 stored @0x48660000
 +## Executing script at 48660000
 +============== Running script =========
 +*** Running from UBFI2 partition @0x48660000
 +Load address = 0x486612bc (0x12bc)
 +Kernel address = 0x48661308 (0x1308)
 +kernel size = 0xdd4f0
 +FS address = 0x4873e7f8 (0xde7f8)
 +FS size = 0x3c3c00
 +NVRAM offset = 0xfb0000
 +NVRAM size = 0x50000
 +*** UBFI2 bootscript executed successfully.
 +Start booting...
 +## Booting image at 486612bc ...
 +   Image Name:   Multi Image File
 +   Image Type:   ARM Linux Multi-File Image (uncompressed)
 +   Data Size:    4854012 Bytes =  4.6 MB
 +   Load Address: 80a00000
 +   Entry Point: ​ 80a00000
 +   ​Contents:​
 +   Image 0:   ​906480 Bytes = 885.2 kB
 +   Image 1:  3947520 Bytes =  3.8 MB
 +   ​Verifying Checksum ... OK
 +OK
 +
 +Starting kernel ...
 +
 +Starting LZMA Uncompression Algorithm.
 +Compressed file is LZMA format.
 +Linux version 2.6.18_pro500 (jimmy@build2.foxconn.com) (gcc version 4.2.0 20070126 (prerelease) (MontaVista 4.2.0-2.0.0.custom 2007-02-12)) #1 PREEMPT Fri Nov 6 11:04:10 CST 2009
 +CPU: ARMv6-compatible processor [410fb764] revision 4 (ARMv6TEJ), cr=00c538ff
 +Machine: puma5
 +Ignoring unrecognised tag 0x00000000
 +Memory policy: ECC disabled, Data cache writethrough
 +Reserved 2048k DSP memory starting from Physical 0x83e00000
 +CPU0: D VIPT write-back cache
 +CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
 +CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
 +Real-Time Preemption Support (C) 2004-2006 Ingo Molnar
 +Built 1 zonelists. ​ Total pages: 15872
 +Kernel command line: root=/​dev/​mtdblock6 mtdparts=spansion:​0x20000(U-Boot)ro,​0x10000(env1),​0x10000(env2),​0x620000@0x40000(UBFI1),​0x620000@0x660000(UBFI2),​0xdd4f0@0x661308(Kernel),​0x3c3c00(RootFileSystem),​0x330000@0xc80000(APImg),​0x50000@0xfb0000(nvram) console=ttyS0,​115200n8 ethaddr0=00:​1e:​2a:​03:​87:​c0 usbhostaddr=00.00.00.00.00.00
 +WARNING: experimental RCU implementation.
 +Interrupt controller revision : 4e822100
 +PID hash table entries: 256 (order: 8, 1024 bytes)
 +Power & Sleep Controller @ 0xd8621000 Initialized [id-0x44822905]
 +Initialized Peripheral Port Remap Register to base : 0x50000000
 +Puma5 Timer0 initialized
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Memory: 62MB = 62MB total
 +Memory: 60244KB available (2036K code, 527K data, 80K init)
 +Mount-cache hash table entries: 512
 +CPU: Testing write buffer coherency: ok
 +NET: Registered protocol family 16
 +Off chip memory allocated: 153088
 +QMgr Init: buffer after alignment: 803c0000
 +avalanche_ppd_init:​ PP system ​ initialized successfully.
 +avalanche_ppd_init(494):​return code 0x00
 +SCSI subsystem initialized
 +usbcore: registered new driver usbfs
 +usbcore: registered new driver hub
 +musb_hdrc: version 2.2a/​db-0.5.1,​ cppi-dma, host, debug=2
 +VBUS off(0)-GPIO14(HIGH)
 +musb_hdrc: USB Host mode controller at d3300000 using DMA, IRQ 24
 +musb_hdrc musb_hdrc: MUSB HDRC host driver
 +musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
 +usb usb1: configuration #1 chosen from 1 choice
 +hub 1-0:1.0: USB hub found
 +hub 1-0:1.0: 1 port detected
 +VBUS on(1)-GPIO14(LOW)
 +HIL Core: Profile intrusive has been Loaded.
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 512 (order: -1, 2048 bytes)
 +TCP established hash table entries: 2048 (order: 4, 65536 bytes)
 +TCP bind hash table entries: 1024 (order: 2, 28672 bytes)
 +TCP: Hash tables configured (established 2048 bind 1024)
 +TCP reno registered
 +squashfs: version 3.3 (2007/​10/​31) Phillip Lougher
 +squashfs: LZMA suppport for slax.org by jro
 +JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
 +Initializing Cryptographic API
 +io scheduler noop registered (default)
 +watchdog: TI Avalanche Watchdog Timer: timer margin 42 sec
 +TI LED driver initialized [major=254]
 +Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
 +serial8250: ttyS0 at MMIO map 0x8610f03 mem 0xd8610f03 (irq = 8) is a TI 16550A
 +serial8250: ttyS1 at MMIO map 0x8610e03 mem 0xd8610e03 (irq = 7) is a TI 16550A
 +loop: loaded (max 8 devices)
 +Loading cpgmac driver for puma5
 +TI CPGMAC_F Linux DDA version 0.1 - CPGMAC_F DDC version 0.2
 +Cpmac: Installed 1 instances.
 +i2c /dev entries driver
 +Serial Flash [Bus:0 CS:0] : s25fl128p 16384KB, 256 sectors each  64KB
 +9 cmdlinepart partitions found on MTD device spansion
 +partitions[0] = {.name = U-Boot, .offset = 0x00000000,​.size = 0x00020000 (128K) }
 +partitions[1] = {.name = env1, .offset = 0x00020000,​.size = 0x00010000 (64K) }
 +partitions[2] = {.name = env2, .offset = 0x00030000,​.size = 0x00010000 (64K) }
 +partitions[3] = {.name = UBFI1, .offset = 0x00040000,​.size = 0x00620000 (6272K) }
 +partitions[4] = {.name = UBFI2, .offset = 0x00660000,​.size = 0x00620000 (6272K) }
 +partitions[5] = {.name = Kernel, .offset = 0x00661308,​.size = 0x000dd4f0 (885K) }
 +partitions[6] = {.name = RootFileSystem,​ .offset = 0x0073e7f8,​.size = 0x003c3c00 (3855K) }
 +partitions[7] = {.name = APImg, .offset = 0x00c80000,​.size = 0x00330000 (3264K) }
 +partitions[8] = {.name = nvram, .offset = 0x00fb0000,​.size = 0x00050000 (320K) }
 +Creating 9 MTD partitions on "​spansion":​
 +0x00000000-0x00020000 : "​U-Boot"​
 +0x00020000-0x00030000 : "​env1"​
 +0x00030000-0x00040000 : "​env2"​
 +0x00040000-0x00660000 : "​UBFI1"​
 +0x00660000-0x00c80000 : "​UBFI2"​
 +0x00661308-0x0073e7f8 : "​Kernel"​
 +mtd: partition "​Kernel"​ doesn'​t start on an erase block boundary -- force read-only
 +0x0073e7f8-0x00b023f8 : "​RootFileSystem"​
 +mtd: partition "​RootFileSystem"​ doesn'​t start on an erase block boundary -- force read-only
 +0x00c80000-0x00fb0000 : "​APImg"​
 +0x00fb0000-0x01000000 : "​nvram"​
 +Serial Flash [Bus:0 CS:1] : No device found
 +ti_spi.0: AVALANCHE SPI Controller driver at 0xd8612500 ​          (irq = 0)
 +ti_codec_spi.0:​ TI Codec SPI Controller driver at 0xd86040c8 ​          (irq = 0)
 +usbmon: debugfs is not available
 +Initializing USB Mass Storage driver...
 +usbcore: registered new driver usb-storage
 +USB Mass Storage support registered.
 +usbcore: registered new driver usbhid
 +drivers/​usb/​input/​hid-core.c:​ v2.6:USB HID core driver
 +IPv4 over IPv4 tunneling driver
 +TCP bic registered
 +Initializing XFRM netlink socket
 +NET: Registered protocol family 1
 +NET: Registered protocol family 10
 +IPv6 over IPv4 tunneling driver
 +NET: Registered protocol family 17
 +NET: Registered protocol family 15
 +VFS: Mounted root (squashfs filesystem) readonly.
 +Freeing init memory: 80K
 +init started: ​ BusyBox v1.4.2 (2009-11-06 11:05:28 CST) multi-call binary
 +init started: ​ BusyBox v1.4.2 (2009-11-06 11:05:28 CST) multi-call binary
 +Starting pid 141, console /dev/tts/0: '/​bin/​sh'​
 +
 +
 +========================================================
 +TI U12C121T10 release 1.4.1.19
 +Build date: Friday, November 06 2009, 11:05:53
 +Copyright (c) 2006 - 2008 Texas Instruments Incorporated
 +========================================================
 +
 +
 +ATHR_PORT0_CTRL:​ 0x6004
 +ATHR_PORT1_CTRL:​ 0x6004
 +ATHR_PORT2_CTRL:​ 0x6004
 +ATHR_PORT3_CTRL:​ 0x6004
 +ATHR_PORT4_CTRL:​ 0x6004
 +ATHR_PORT5_CTRL:​ 0x6004
 +ATHR_PORT0_VLAN:​ 0x3e0001
 +ATHR_PORT1_VLAN:​ 0x3d0001
 +ATHR_PORT2_VLAN:​ 0x3b0001
 +ATHR_PORT3_VLAN:​ 0x370001
 +ATHR_PORT4_VLAN:​ 0x2f0001
 +ATHR_PORT5_VLAN:​ 0x1f0001
 +Autoconfiguration disabled for eth0
 +Thu Jan  1 00:00:03 UTC 1970
 +Recover the switch ...WRITE: address = 0x03000008, value = 0x012E9B66
 +WRITE: address = 0x03000100, value = 0x0000007E
 +WRITE: address = 0x03000600, value = 0x0000007E
 +WRITE: address = 0x03000200, value = 0x00000200
 +WRITE: address = 0x03000300, value = 0x00000200
 +WRITE: address = 0x03000400, value = 0x00000200
 +WRITE: address = 0x03000500, value = 0x00000200
 +WRITE: address = 0x03000104, value = 0x00004204
 +WRITE: address = 0x03000204, value = 0x00006104
 +WRITE: address = 0x03000304, value = 0x00006104
 +WRITE: address = 0x03000404, value = 0x00006104
 +WRITE: address = 0x03000504, value = 0x00006104
 +WRITE: address = 0x03000604, value = 0x00006104
 +WRITE: address = 0x03000108, value = 0x003E0003
 +WRITE: address = 0x03000208, value = 0x001D0001
 +WRITE: address = 0x03000308, value = 0x001B0001
 +WRITE: address = 0x03000408, value = 0x00170001
 +WRITE: address = 0x03000508, value = 0x000F0001
 +WRITE: address = 0x03000608, value = 0x00010002
 +WRITE: address = 0x0300002C, value = 0x003F003F
 +WRITE: address = 0x03000030, value = 0x21F005F2
 +PING 192.168.101.254 (192.168.101.254):​ 56 data bytes
 +
 +--- 192.168.101.254 ping statistics ---
 +1 packets transmitted,​ 0 packets received, 100% packet loss
 +WRITE: address = 0x03000104, value = 0x00006004
 +WRITE: address = 0x03000204, value = 0x00006004
 +WRITE: address = 0x03000304, value = 0x00006004
 +WRITE: address = 0x03000404, value = 0x00006004
 +WRITE: address = 0x03000504, value = 0x00006004
 +WRITE: address = 0x03000604, value = 0x00006004
 +WRITE: address = 0x03000001, value = 0x00000104
 +WRITE: address = 0x03000001, value = 0x00000204
 +WRITE: address = 0x03000001, value = 0x00000304
 +WRITE: address = 0x03000001, value = 0x00000404
 +WRITE: address = 0x03000001, value = 0x00000504
 +WRITE: address = 0x03000001, value = 0x00000604
 +PASS
 +Daemon Successfully forked (pid: 288)
 +===== Wait for AP ready =====
 +....Rx Channel TearDown Descriptor Found 803d8b00
 +numBD = 65
 +Tx Channel Teardown Descriptor found! 803d8020
 + Using DOCSIS Initialization process parameters: -ds_channels 4 -us_channels 4 -debug_options 1048576
 +Using DOCSIS MAC Driver parameters: -1st_freq 294000000
 +Using DOCSIS MAC Manager parameters: -x -m
 +Starting pid 385, console /dev/tts/0: '/​bin/​sh'​
 +
 +
 +BusyBox v1.4.2 (2009-11-06 11:05:28 CST) Built-in shell (ash)
 +Enter '​help'​ for a list of built-in commands.
 +
 +# pcd: Starting TI Process Control Daemon.
 +pcd: Loaded 76 rules.
 +pcd: Initialization complete.
 +pcd: Starting process /​usr/​sbin/​watchdog_rt (Rule SYSTEM_WATCHDOG).
 +TI Watchdog-RT daemon started <kick interval = 10 seconds>
 +pcd: Starting process /​usr/​sbin/​logger (Rule SYSTEM_LOGGER).
 +pcd: Rule SYSTEM_WATCHDOG:​ Success (Process /​usr/​sbin/​watchdog_rt (386)).
 +TI Logger: Init complete
 +pcd: Rule SYSTEM_LOGGER:​ Success (Process /​usr/​sbin/​logger (387)).
 +pcd: Starting process /​usr/​sbin/​gptimer (Rule SYSTEM_GPTIMER).
 +pcd: Rule SYSTEM_GPTIMER:​ Success (Process /​usr/​sbin/​gptimer (388)).
 +pcd: Rule SYSTEM_LASTRULE:​ Success.
 +pcd: Starting process /bin/sh (Rule BBU_INITDRV).
 +BBU Kernel module - installing
 +<​4>​BbuIsRev2:​ rev 1
 +BBU Kernel module installed - 0
 +pcd: Rule BBU_INITDRV:​ Success (Process /bin/sh (390)).
 +pcd: Starting process /​usr/​sbin/​bbusm (Rule BBU_SM).
 +pcd: Rule BBU_SM: Success (Process /​usr/​sbin/​bbusm (401)).
 +pcd: Starting process /bin/sh (Rule BBU_DLMRMMOD).
 +pcd: Rule BBU_LASTRULE:​ Success.
 +pcd: Starting process echo (Rule DOCSIS_APPRUN).
 +pcd: Rule DOCSIS_APPRUN:​ Success (Process echo (404)).
 +pcd: Starting process /​usr/​sbin/​docsis_init_once (Rule DOCSIS_INITONCE).
 +pcd: Starting process insmod (Rule DOCSIS_BRIDGE).
 +Dbridge MDF control init done
 +pcd: Rule DOCSIS_BRIDGE:​ Success (Process insmod (406)).
 +pcd: Starting process insmod (Rule DOCSIS_CNI).
 +pcd: Rule DOCSIS_CNI: Success (Process insmod (411)).
 +pcd: Rule DOCSIS_INITONCE:​ Success (Process /​usr/​sbin/​docsis_init_once (405)).
 +pcd: Starting process /​usr/​sbin/​ledd (Rule DOCSIS_LED).
 +pcd: Rule DOCSIS_LED: Success (Process /​usr/​sbin/​ledd (416)).
 +pcd: Starting process insmod (Rule DOCSIS_HALVLYNQ).
 +pcd: Starting process /​usr/​sbin/​cm_status (Rule DOCSIS_CMSTATUS).
 +VLYNQ driver initialization complete.
 +pcd: Rule DOCSIS_HALVLYNQ:​ Success (Process insmod (417)).
 +pcd: Starting process insmod (Rule DOCSIS_SOCIFDRV).
 +pcd: Rule DOCSIS_CMSTATUS:​ Success (Process /​usr/​sbin/​cm_status (418)).
 +pcd: Rule DOCSIS_SOCIFDRV:​ Success (Process insmod (421)).
 +pcd: Starting process mknod (Rule DOCSIS_MKNODSOCIFDRV).
 +pcd: Rule DOCSIS_MKNODSOCIFDRV:​ Success (Process mknod (423)).
 +pcd: Starting process insmod (Rule DOCSIS_MNG).
 +pcd: Rule DOCSIS_MNG: Success (Process insmod (424)).
 +pcd: Starting process mknod (Rule DOCSIS_MKNODMNG).
 +pcd: Starting process insmod (Rule DOCSIS_KINTR).
 +pcd: Rule DOCSIS_MKNODMNG:​ Success (Process mknod (426)).
 +pcd: Starting process insmod (Rule DOCSIS_FILTERCLASS).
 +pcd: Rule DOCSIS_KINTR:​ Success (Process insmod (427)).
 +pcd: Starting process /​usr/​sbin/​hal_event_mbox (Rule DOCSIS_HALEVENTMBOX).
 +pcd: Starting process /​usr/​sbin/​hal_cmd_mbox (Rule DOCSIS_HALCMDMBOX).
 +pcd: Rule DOCSIS_HALCMDMBOX:​ Success (Process /​usr/​sbin/​hal_cmd_mbox (437)).
 +pcd: Rule DOCSIS_FILTERCLASS:​ Success (Process insmod (434)).
 +pcd: Starting process /bin/sh (Rule DOCSIS_FCDEV).
 +pcd: Rule DOCSIS_HALEVENTMBOX:​ Success (Process /​usr/​sbin/​hal_event_mbox (436)).
 +pcd: Starting process /​usr/​sbin/​mlx (Rule DOCSIS_MLX).
 +pcd: Rule DOCSIS_MLX: Success (Process /​usr/​sbin/​mlx (441)).
 +pcd: Rule DOCSIS_FCDEV:​ Success (Process /bin/sh (439)).
 +pcd: Starting process /​usr/​sbin/​hal_tuner_mgr (Rule DOCSIS_HALTUNERMGR).
 +pcd: Starting process /​usr/​sbin/​dbridge_init (Rule DOCSIS_DBRIDGEINIT).
 +pcd: Rule DOCSIS_HALTUNERMGR:​ Success (Process /​usr/​sbin/​hal_tuner_mgr (452)).
 +Ingress Hook on  eth0
 +Dbridge Init SUCSESS
 +Autoconfiguration disabled for br0
 +pcd: Rule DOCSIS_HALREADY:​ SucceHAL_MacDsUnicastDataFilterAdd:​ system_rev = 1
 +ss.
 +pcd: Starting process /​usr/​Autoconfiguration disabled for lbr0
 +sbin/​qos_dsx_sm (Rule DOCSIS_QOSDSXSM).
 +ATHR_PORT0_CTRL:​ 0x6004
 +pcd: Starting process /​usr/​sbin/​dispatcher (Rule DOCSIS_DISPATCHER).
 +pcd: Starting process /​usr/​sbin/​bpi_auth (Rule DOCSIS_BPIAUTH).
 +ATHR_PORT1_CTRL:​ 0x6004
 +ATHR_PORT2_CTRL:​ 0x6004
 +ATHR_PORT3_CTRL:​ 0x6004
 +ATHR_PORT4_CTRL:​ 0x6004
 +ATHR_PORT5_CTRL:​ 0x6004
 +ATHR_PORT0_VLAN:​ 0x3e0003
 +ATHR_PORT1_VLAN:​ 0x1d0001
 +ATHR_PORT2_VLAN:​ 0x1b0001
 +ATHR_PORT3_VLAN:​ 0x170001
 +ATHR_PORT4_VLAN:​ 0xf0001
 +ATHR_PORT5_VLAN:​ 0x10002
 +Autoconfiguration disabled for eth0
 +netlink_open:​ initialized fd 6
 +pcd: Rule DOCSIS_DISPATCHER:​ Success (Process /​usr/​sbin/​dispatcher (459)).
 +pcd: Starting process /​usr/​sbin/​docsis_mac_driver (Rule DOCSIS_MACDRIVER).
 +HAL_MacDsUnicastDataFilterAdd:​ system_rev = 1
 +Autoconfiguration disabled for lan0
 +Autoconfiguration disabled for wan0
 +HAL_MacDsUnicastDataFilterAdd:​ system_rev = 1
 +Autoconfiguration disabled for cni0
 +pcd: Rule DOCSIS_DBRIDGEINIT:​ Success (Process /​usr/​sbin/​dbridge_init (453)).
 +pcd: Starting process /bin/sh (Rule FOXCONN_SWITCH_CHK).
 +pcd: Starting process /​usr/​foxconn/​bin/​push_buttond (Rule FOXCONN_PUSH_BUTTOND).
 +pcd: Starting process /bin/sh (Rule FOXCONN_INIT_SW).
 +pcd: Starting process /​usr/​foxconn/​bin/​evtMonitor (Rule FOXCONN_EVT_MONITOR).
 +pcd: Starting process /​usr/​sbin/​snmp_agent_cm (Rule DOCSIS_SNMPAGENT).
 +pcd: Starting process /bin/sh (Rule DOCSIS_DBRIDGEMDFINIT).
 +pcd: Rule DOCSIS_QOSDSXSM:​ Success (Process /​usr/​sbin/​qos_dsx_sm (458)).
 +pcd: Rule FOXCONN_EVT_MONITOR:​ Success (Process /​usr/​foxconn/​bin/​evtMonitor (475)).
 +pcd: Rule FOXCONN_PUSH_BUTTOND:​ Success (Process /​usr/​foxconn/​bin/​push_buttond (473)).
 +pcd: Rule FOXCONN_SWITCH_CHK:​ Success (Process /bin/sh (472)).
 +pcd: Rule DOCSIS_BPIAUTH:​ Success (Process /​usr/​sbin/​bpi_auth (460)).
 +pcd: Starting process /​usr/​sbin/​bpi_tek (Rule DOCSIS_BPITEK).
 +pcd: Starting process /​usr/​sbin/​bpi_sa_map (Rule DOCSIS_BPISAMAP).
 +Polling interval is 250, 250
 +Reset default time is 5000, 5000
 +read factory mode: routing
 +
 +isFactoryMode:​0
 +pcd: Starting process /​usr/​sbin/​downstream_manager (Rule DOCSIS_DSMNGR4).
 +pcd: Starting process /​usr/​sbin/​downstream_manager (Rule DOCSIS_DSMNGR3).
 +pcd: Starting process /​usr/​sbin/​downstream_manager (Rule DOCSIS_DSMNGR2).
 +pcd: Starting process /​usr/​sbin/​downstream_manager (Rule DOCSIS_DSMNGR1).
 +WRITE: address = 0x03000104, value = 0x00004204
 +pcd: Rule DOCSIS_DBRIDGEMDFINIT:​ Success (Process /bin/sh (477)).
 +pcd: Starting process insmod (Rule DOCSIS_PP).
 +WRITE: address = 0x03000204, value = 0x00006104
 +WRITE: address = 0x03000304, value = 0x00006104
 +WRITE: address = 0x03000404, value = 0x00006104
 +pcd: Rule DOCSIS_BPISAMAP:​ Success (Process /​usr/​sbin/​bpi_sa_map (481)).
 +WRITE: address = 0x03000504, value = 0x00006104
 +WRITE: address = 0x03000604, value = 0x00006104
 +WRITE: address = 0x03000108, value = 0x003E0003
 +WRITE: address = 0x03000208, value = 0x001D0001
 +WRITE: address = 0x03000308, value = 0x001B0001
 +pcd: Rule DOCSIS_BPITEK:​ Success (Process /​usr/​sbin/​bpi_tek (480)).
 +WRITE: address = 0x03000408, value = 0x00170001
 +WRITE: address = 0x03000508, value = 0x000F0001
 +WRITE: address = 0x03000608, value = 0x00010002
 +WRITE: address = 0x0300002C, value = 0x003F003F
 +WRITE: address = 0x03000030, value = 0x21F005F2
 +pcd: Rule FOXCONN_INIT_SW:​ Success (Process /bin/sh (474)).
 +pcd: Starting process /​sbin/​utelnetd (Rule FOXCONN_TELNETD).
 +pcd: Rule FOXCONN_TELNETD:​ Success (Process /​sbin/​utelnetd (539)).
 +Create DOCSIS Packet Processor counters char device done
 +Init Docsis Packet Processor counters DB done.
 +DOCSIS Packet Processor counters control init done
 +DOCSIS Packet Processor control init done
 +pcd: Rule DOCSIS_PP: Success (Process insmod (513)).
 +pcd: Starting process /bin/sh (Rule DOCSIS_PPDEV).
 +pcd: Rule DOCSIS_DSMNGR2:​ Success (Process /​usr/​sbin/​downstream_manager (505)).
 +pcd: Rule DOCSIS_DSMNGR4:​ Success (Process /​usr/​sbin/​downstream_manager (501)).
 +pcd: Rule DOCSIS_DSMNGR3:​ Success (Process /​usr/​sbin/​downstream_manager (502)).
 +pcd: Rule DOCSIS_DSMNGR1:​ Success (Process /​usr/​sbin/​downstream_manager (506)).
 +pcd: Starting process /​usr/​sbin/​upstream_manager (Rule DOCSIS_USMNGR1).
 +pcd: Starting process /​usr/​sbin/​upstream_manager (Rule DOCSIS_USMNGR2).
 +pcd: Starting process /​usr/​sbin/​upstream_manager (Rule DOCSIS_USMNGR3).
 +pcd: Starting process /​usr/​sbin/​upstream_manager (Rule DOCSIS_USMNGR4).
 +SNMPA_CreateSocketEntry : type 0, addr = 0, port = 0, ifname = /​var/​tmp/​cm_snmp_ctrl List = (nil)
 +Cntl Entry created
 +telnetd: starting
 +  port: 23; interface: any; login program: /bin/login
 +PGA Type: MT1570
 +
 +resetEnabled:​1
 +pcd: Rule DOCSIS_USMNGR3:​ Success (Process /​usr/​sbin/​upstream_manager (555)).
 +pcd: Rule DOCSIS_USMNGR4:​ Success (Process /​usr/​sbin/​upstream_manager (556)).
 +pcd: Rule DOCSIS_USMNGR1:​ Success (Process /​usr/​sbin/​upstream_manager (553)).
 +pcd: Rule DOCSIS_PPDEV:​ Success (Process /bin/sh (541)).
 +pcd: Rule DOCSIS_USMNGR2:​ Success (Process /​usr/​sbin/​upstream_manager (554)).
 +pcd: Rule DOCSIS_MACDRIVER:​ Success (Process /​usr/​sbin/​docsis_mac_driver (463)).
 +Unloading the BBU DLM
 +BBU module is down!
 +pcd: Rule BBU_DLMRMMOD:​ Success (Process /bin/sh (403)).
 +pcd: Rule DOCSIS_SNMPAGENT:​ Success (Process /​usr/​sbin/​snmp_agent_cm (476)).
 +SNMPA_CreateSocketEntry : type 1, addr = c0a86501, port = 161, ifname = lan0 List = 0x69750
 +SNMPA_CreateSocketEntry : type 1, addr = c0a86501, port = 162, ifname = lan0 List = 0x69750
 +pcd: Starting process /​usr/​sbin/​eventmgr_cm (Rule DOCSIS_EVENTMNGR).
 +pcd: Rule DOCSIS_EVENTMNGR:​ Success (Process /​usr/​sbin/​eventmgr_cm (1014)).
 +pcd: Starting process /​usr/​sbin/​docsis_mac_manager (Rule DOCSIS_MACMANAGER).
 +pcd: Rule DOCSIS_MACMANAGER:​ Success (Process /​usr/​sbin/​docsis_mac_manager (1015)).
 +pcd: Rule DOCSIS_LASTRULE:​ Success.
 +pcd: Starting process insmod (Rule PACM_MTANI).
 +mtani: Network interface initialized successfully
 +RTNL: assertion failed at net/​ipv4/​devinet.c (987)
 +RTNL: assertion failed at net/​ipv6/​addrconf.c (2170)
 +RTNL: assertion failed at net/​ipv6/​addrconf.c (1644)
 +RTNL: assertion failed at net/​ipv6/​addrconf.c (456)
 +RTNL: assertion failed at net/​ipv6/​addrconf.c (367)
 +Autoconfiguration disabled for esafe0
 +mtani: Network interface registered successfully
 +pcd: Rule PACM_MTANI: Success (Process insmod (1016)).
 +pcd: Starting process /​usr/​sbin/​pacm_init (Rule PACM_INIT).
 +Autoconfiguration disabled for mta0
 +HAL_MacDsUnicastDataFilterAdd:​ system_rev = 1
 +Production config saved to NVRAMSTA MAC initialized to 00:​26:​F2:​66:​29:​51PACM - Exec PACM_Prov_DbInit
 +PACM - Exec PACM_MSM_DbInit
 +PACM - Exec Security_InitDataBase
 +PACM - Exec SnmpDB_Init
 +pcd: Rule PACM_INIT: Success (Process /​usr/​sbin/​pacm_init (1020)).
 +pcd: Starting process insmod (Rule VOICE_INSMXPMOD).
 +pcd: Starting process /​usr/​sbin/​pacm_vendor_app (Rule PACM_VENDORAPP).
 +pcd: Starting process /​usr/​sbin/​pacm_snmp_agent (Rule PACM_SNMP).
 +pcd: Starting process /​usr/​sbin/​pacm_security (Rule PACM_SECURITY).
 +pcd: Starting process /​usr/​sbin/​pacm_event_mgr (Rule PACM_EVENTMGR).
 +pcd: Starting process /​usr/​sbin/​pacm_doim (Rule PACM_DOIM).
 +pcd: Rule PACM_VENDORAPP:​ Success (Process /​usr/​sbin/​pacm_vendor_app (1026)).
 +MXP_TMR: Calibrating MXP Timer... ​  ​Ticks/​sec=200
 +Starting MXP timer
 +MXP module loaded
 +pcd: Rule VOICE_INSMXPMOD:​ Success (Process insmod (1025)).
 +pcd: Starting process insmod (Rule VOICE_INSMXPMEM).
 +pcd: Rule PACM_EVENTMGR:​ Success (Process /​usr/​sbin/​pacm_event_mgr (1029)).
 +MXP memory module loaded
 +pcd: Rule PACM_DOIM: Success (Process /​usr/​sbin/​pacm_doim (1030)).
 +pcd: Rule VOICE_INSMXPMEM:​ Success (Process insmod (1038)).
 +pcd: Starting process insmod (Rule VOICE_INSDSPMOD).
 +Processing configuration file...
 +Found command: sysdescr eMTA SNMP Agent
 +Found command: syscontact ​      ​NETGEAR
 +Found command: sysLocation ​     Santa Clara, CA 95054
 +Found command: read-community ​  ​public
 +Found command: write-community ​ private
 +Found command: trap-community ​  ​SNMP-trap
 +Found command: nv-file ​    /​etc/​snmp_mta_nv.txt
 +Hit EOF of config file
 +
 +
 +****HOST INFORMATION****
 +sysDescr is "eMTA SNMP Agent"
 +sysContact is "​NETGEAR"​
 +sysLocation is "Santa Clara, CA 95054"
 +System Boot time was Thu Jan  1 00:00:44 1970
 +System object identifier has 14 components:
 +        0.0.0.0.0.0.0.0.0.0.0.0.0.0.
 +
 +
 +****SNMP AGENT INFORMATION****
 +Community names:
 +        Read:   ​public
 +        Write: ​ private
 +        Trap:   ​SNMP-trap
 +         ​nv-file:​ /​etc/​snmp_mta_nv.txt
 +
 +
 +SNMPA_CreateSocketEntry : type 0, addr = 0, port = 0, ifname = /​var/​tmp/​mta_snmp_ctrl List = (nil)
 +Cntl Entry created
 +pcd: Rule PACM_SECURITY:​ Success (Process /​usr/​sbin/​pacm_security (1028)).
 +57: Disabling ​ PUMAV DSPSS
 +60: Taking PUMAV DSPSS IN  RESET
 +HW_DSP module loaded
 +pcd: Rule VOICE_INSDSPMOD:​ Success (Process insmod (1041)).
 +pcd: Starting process insmod (Rule VOICE_INSTELEHAL).
 +TIUHAL: Finished TDM configuration
 +spi_tid_probe:​ Setting TID template
 +TIUHAL using DOCSIS clock source
 +pcd: Rule VOICE_INSTELEHAL:​ Success (Process insmod (1063)).
 +pcd: Starting process udevstart (Rule VOICE_UDEVSTART).
 +pcd: Rule VOICE_UDEVSTART:​ Success (Process udevstart (1073)).
 +pcd: Starting process /​usr/​sbin/​ggncs (Rule VOICE_GGAPP).
 +Initializing signal_handler
 +tcb_alloc: task id=1,​name=mxproot,​busy=1
 +tcb_alloc: task id=2,​name=XSPY,​busy=1
 +tcb_alloc: task id=3,​name=XTELNET,​busy=1
 +tcb_alloc: task id=4,​name=ROOT,​busy=1
 +>>>>​ rootInit <<<<<​
 +Creating Golden Gateway application...
 +Registered with TIUHAL version 3tcb_alloc: task id=5,​name=NWIF01,​busy=1
 +tcb_alloc: task id=6,​name=DQMM,​busy=1
 +
 +TID(M) 0 is VE88276PTC014
 +num_hw_tcids = 2 num of TIDS=1
 +VP880_236: SLIC termination type 0
 +tiuhw_setup_chipselect:​ cs for tcid 2 = 4 fxo: 0
 +Loading dsp image: /​lib/​dspimage.ld
 +tcb_alloc: task id=7,​name=DLMM,​busy=1
 +tcb_alloc: task id=8,​name=ISU,​busy=1
 +tcb_alloc: task id=9,​name=VIM,​busy=1
 +tcb_alloc: task id=10,​name=CCU,​busy=1
 +tcb_alloc: task id=11,​name=RTCP,​busy=1
 +tcb_alloc: task id=12,​name=PMA,​busy=1
 +tcb_alloc: task id=13,​name=DEX,​busy=1
 +DSPMOD query DSP address syscall: DSP Start address = 0x83E00000
 +HW_DSP DSP External Config Register set to: 0x83000000, Start: 0x83E00000
 +57: Disabling ​ PUMAV DSPSS
 +60: Taking PUMAV DSPSS IN  RESET
 +DSP external memory mapped to 0x04484000 (User Sp) = 0x83E00000 (Kernel Sp)
 +dimhw_init_dsp:​ dpr_base mapped to 0x03684000 (User sp)
 +tcb_alloc: task id=14,​name=DCMM,​busy=1
 +tcb_alloc: task id=15,​name=CPMU,​busy=1
 +tcb_alloc: task id=16,​name=xGCP,​busy=1
 +tcb_alloc: task id=17,​name=NMM,​busy=1
 +tcb_alloc: task id=18,​name=VOIMFE,​busy=1
 +tcb_free: task id=4, name=ROOT
 +FXS FXR = 16
 +hw_config: tcid: 0 onhook volts = 48, offhook current = 26,  country = 1
 +hw_config: tcid: 0 ringer type: 1 frequency: 20 amplitude: 66 offset: 0
 +Attempting to delete TCB: 4
 +XtDelete called
 +lmxp_tcb_free called for 4
 +pcd: Rule VOICE_GGAPP:​ Success (Process /​usr/​sbin/​ggncs (1074)).
 +Received request for gain settings for TCID: 0, rx = -4, tx = -2
 +pcd: Rule VOICE_LASTRULE:​ Success.
 +INT ENABLE 0 OK, int_mask 9c 9c
 +hw_config: tcid: 1 onhook volts = 48, offho57: Disabling ​ PUMAV DSPSS
 +60: Taking PUMAV DSPSS IN  RESET
 +ok current = 26,  country = 1
 +hw_config: tcid: 1 ringer type: 1 frequency: 20 amplitude: 66 offset: 0
 +Received request for gain settings for TCID: 1, rx = -4, tx = -2
 +INT ENABLE 1 OK, int_mask 9c 9c
 +[ERROR]: 0000000646 - NCSDK Version: 2.4.4
 +[ERROR]: 0000000646 - ROOT:Number of tcids in the system ​ 2: 2: 2: 6
 +[ERROR]: 0000000646 - MAS Version: 2.4.4(Build 15)
 +[ERROR]: 0000000646 - Following features compiled out of the build:
 +[ERROR]: 0000000646 -   ​DIM_DNLD_PAGED_BOOT
 +[ERROR]: 0000000646 -   ​DIM_DNLD_DIRECT
 +[ERROR]: 0000000646 -   ​DIM_DNLD_MSG
 +[ERROR]: 0000000646 -   ​DIM_DNLD_RST_DIRECT
 +[ERROR]: 0000000646 -   ​DIM_CHAN_IF
 +[ERROR]: 0000000646 -   ​ANNC_IF
 +[ERROR]: 0000000646 -   ​DIM_RTCP_IF
 +[ERROR]: 0000000646 -   ​DIM_SIG_IF
 +[ERROR]: 0000000646 -   ​DIM_AUDIO_IF
 +[ERROR]: 0000000646 -   ​DIM_AFE_IF
 +[ERROR]: 0000000646 -   ​DIM_LOMGR_GEN_FIFO
 +[ERROR]: 0000000646 -   ​DIM_LOMGR_CHN_FIFO
 +[ERROR]: 0000000646 -   ​DIM_LOMGR_MAIL_BOX
 +[ERROR]: 0000000646 -   ​PROTO_AAL2
 +[ERROR]: 0000000646 -   ​PROTO_CLRDT
 +[ERROR]: 0000000646 -   ​PROTO_MODEM
 +[ERROR]: 0000000646 -   ​DIM_3PROC
 +[ERROR]: 0000000646 -   ​DIM_DETAILED_SPY
 +[ERROR]: 0000000646 - Following features not defined in build and have been enabled
 +[ERROR]: 0000000646 - by default; REVIEW to remove potential unecessary code:
 +[ERROR]: 0000000646 -   All features are accounted for!!!
 +[ERROR]: 0000000646 - ISU: isu_module_init isu_event_base 0x0, task 0x00000000
 +
 +[ERROR]: 0000000646 - ISU: isu_create 0x00000008 queue 1
 +
 +[ERROR]: 0000000646 - CCU: ccu_module_init ccu_event_base 0x0, task 0x00000000
 +
 +[ERROR]: 0000000646 - CCU: ccu_create 0x0000000A queue 1 watchdog timer 2
 +
 +[ERROR]: 0000000646 - DIM: status_request_period out of range [20 - 10000]
 +[ERROR]: 0000000646 - DIM: status_request_period set to default [1000]
 +[ERROR]: 0000000646 - TIU max tcids = 2, poll mode = 0, poll period = 5
 +
 +[ERROR]: 0000000646 - TIU: Polling period must be multiple of 2 msec
 +[ERROR]: 0000000674 - DIM: 0:*, dimp_find_and_init_lo_mgr(). max simple msg len (128) < sizeof(mgb_t)(130)
 +pcd: Rule PACM_SNMP: Success (Process /​usr/​sbin/​pacm_snmp_agent (1027)).
 +pcd: Rule PACM_INITDONE:​ Success.
 +pcd: Starting process /​usr/​sbin/​pacm_mta_control (Rule PACM_MTACTRL).
 +pcd: Rule PACM_MTACTRL:​ Success (Process /​usr/​sbin/​pacm_mta_control (1101)).
 +pcd: Rule PACM_LASTRULE:​ Success.
 +pcd: Starting process /bin/sh (Rule FOXCONN_INIT_VOIP_SETTI).
 +pcd: Rule FOXCONN_INIT_VOIP_SETTI:​ Success (Process /bin/sh (1102)).
 +##############​ voip settings ##################​
 +
 +Console redirected to an external telnet connection
 +ÿýÿý!ÿûÿûTexas Instruments Inc. 2007
 +Golden Gateway Remote Command Processor
 +MXP>set xgcp country 14
 +
 + ​Setting country Denmark ​ ...
 +
 + ​nmm_ring_cadence_table Rin57: Enabling ​ PUMAV DSPSS
 +60: Taking PUMAV DSPSS OUT of  RESET
 +gCadence(10) : duration = -1, repeat = 0
 +   ​pulse(0) : 15 on 150 off
 +
 + ​country_ring_params RingCadence(10) : duration = -1, repeat = 0
 +   ​pulse(0) : 15 on 150 off
 +[ERROR]: 0000000891 - NWIF: DQOS is set to NORMAL
 +[ERROR]: 0000000891 - XGCP CAIF: OUR IP UNKNOWN.. CAIF NOT UP
 +[ERROR]: 0000000896 - DIM: , CHECKSUM=8575
 +[ERROR]: 0000000897 - DIM: 0:*, Core Download complete!
 +[ERROR]: 0000000901 - DIM: 0:*, CONFIG has been received!
 +[ERROR]: 0000000901 - DIM: 0:*, dimp_find_and_init_lo_mgr(). max simple msg len (128) < sizeof(mgb_t)(130)
 +[ERROR]: 0000000903 - DSPA: DSP 0,Image 0:Download done!
 +FcUtils_AddSysInterface:​ Failed to get net device struct for usb0
 +hw_config: tcid: 0 onhook volts = 48, offhook current = 26,  country = 1
 +hw_config: tcid: 0 ringer type: 1 frequency: 25 amplitude: 66 offset: 0
 +INT ENABLE 0 OK, int_mask 9c 9c
 +Received request for gain settings for TCID: 0, rx = 0, tx = 0
 +INT ENABLE 0 OK, int_mask 9c 9c
 +hw_config: tcid: 1 onhook volts = 48, offhook current = 26,  country = 1
 +hw_config: tcid: 1 ringer type: 1 frequency: 25 amplitude: 66 offset: 0
 +INT ENABLE 1 OK, int_mask 9c 9c
 +Received request for gain settings for TCID: 1, rx = 0, tx = 0
 +INT ENABLE 1 OK, int_mask 9c 9c
 +Connection closed
 +OK
 +MXP>
 +#</​nowiki>​
 +</​WRAP>​\\
 +
 +===== Tags =====
 +[[meta:​tags|How to add tags]]
 +{{tag>​GigabitEthernet 1NIC 1WNIC 1Ant 802.11bgn 4Port USB 1USB DOCSIS3 MiniPCI DetachableAntenna 64RAM 16Flash MIPS usb2.0 jtag armv6}}