User Tools

Site Tools


ru:toh:sagem:fast2804

Sagemcom F@ST 2804 rev 1

Этот роутер поставляется российским оператором Ростелеком. FIXME:дополняйте и переводите народ, я тут один. :(

Существует 2 аппарата(или более) под этим номером:

1)Sagemcom F@ST 2804

2)Sagemcom F@ST 2804 rev 1(Sagemcom F@ST 1704N_1864)

Hardware Highlights

SoC Ram Flash Network WiFi USB Serial JTag
Broadcom 6318 / 333 MHz 64MiB 8MiB 4 x 1 802.11bgn, 2 antennas(говорят одна обрезана) BCM43131 Yes Yes ?

Отличительный признак: 1 роутер имеет 2 usb входа, 2 роутер имеет 1 usb вход. Примечание: синие они не от версии usb 3.0, а от краски.:)

Чтобы прошить первый роутер, следуйте по ссылке: Инструкция к прошивке Sagemcom F@ST 2804 FIXME: позже перенести в статью.

Чтобы прошить второй роутер, нужно прошить админку следующим файлом: Образ от Леонида (предварительно распаковав архив), а позже обновиться с sysupgrade с сохранением параметров на https://downloads.openwrt.org/snapshots/trunk/brcm63xx/generic/openwrt-brcm63xx-generic-FAST2704N-squashfs-cfe.bin . FIXME:знающие люди, помогите слезть нам с транка.

User/Pass

1)admin/admin

2)superadmin/Is$uper@dmin

Официальная прошивка

Bootlog

HELO CPUI L1CI DRAM ---- PHYS PHYE DDR1 333H SIZ3 RACE PASS ---- ZBSS CODE DATA L12F MAIN CFE version 7.232 for BCM96318 (32bit,SP,BE) Build Date: Tue Jul 30 10:10:48 CST 2013 (laixinliu@SZ01007.DONGGUAN.CN) Copyright (C) 2005-2012 SAGEMCOM Corporation. HS Serial flash device: name MX25L64, id 0xc217 size 8192KB Total Flash size: 8192K with 2048 sectors Chip ID: BCM6318B0, MIPS: 333MHz, DDR: 333MHz, Bus: 166MHz Main Thread: TP0 Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-5) : F@ST1704N Number of MAC Addresses (1-32) : 11 Base MAC Address : 68:15:90:ea:9b:46 PSI Size (1-64) KBytes : 40 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Booting from only image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x802f9780 Decompression OK! Entry at 0x802f9780 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x802f9780 Linux version 2.6.30 (bensonli@sz01017.ads.local) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Wed Sep 18 18:54:02 CST 2013 HS Serial flash device: name MX25L64, id 0xc217 size 8192KB F@ST1704N prom init CPU revision is: 00029033 (Broadcom BCM3302) DSL SDRAM reserved: 0x100000 Determined physical RAM map: memory: 03f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003f00 On node 0 totalpages: 16128 free_area_init_node: node 0, pgdat 80391130, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11938 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 59908k/64512k available (3006k kernel code, 4584k reserved, 586k data, 136k init, 0k highmem) Calibrating delay loop... 331.77 BogoMIPS (lpj=165888) Mount-cache hash table entries: 512 --Kernel Config-- SMP=0 PREEMPT=0 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Sep 18 2013 18:51:51 net_namespace: 1128 bytes NET: Registered protocol family 16 Total Flash size: 8192K with 2048 sectors registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usb_fortune: Module loaded. usbcore: registered new device driver usb pci 0000:00:09.0: reg 10 32bit mmio: [0x10005100-0x100051ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10005000-0x100050ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x007fff] pci 0000:02:00.0: supports D1 D2 pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: 0x10200000-0x102fffff pci 0000:01:00.0: PREFETCH window: disabled PCI: Enabling device 0000:01:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Sep 18 2013 18:53:58 initialized Broadcom GBPM v0.1 Sep 18 2013 18:53:59 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 usbcore: registered new interface driver huawei_ether NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher squashfs: version 4.0 with LZMA457 ported by BRCM fuse init (API version 7.11) msgmni has been set to 117 io scheduler noop registered (default) pcieport-driver 0000:01:00.0: device [14e4:6318] has invalid IRQ; check vendor BIOS PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 PPPoL2TP kernel driver, V1.0 usbcore: registered new interface driver cdc_ether bcm963xx_mtd driver v1.0 File system address: 0xb8010100 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10005000 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected generic_probe wake up Monitor!! message received before monitor task is initialized kerSysSendtoMonitorTask ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 49, io mem 0x10005100 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected generic_probe wake up Monitor!! message received before monitor task is initialized kerSysSendtoMonitorTask usbcore: registered new interface driver cdc_acm cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems brcmboard: brcm_board_init entry SES: Button Interrupt 0x0 is enabled SES: LED GPIO 0x8031 is enabled Serial: BCM63XX driver $Revision: 3.00 $ Magic SysRq enabled (type ^ h for list of supported commands) ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX Total # RxBds=2698 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmxtmrt: Broadcom BCM6318B0 ATM/PTM Network Device v0.5 Sep 18 2013 18:53:49 BCM63XX_USB USB Device not present GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 136k freed init started: BusyBox v1.17.2 (2013-09-18 18:56:34 CST) starting pid 208, tty '': '/etc/init.d/rcS' usbfs: unrecognised mount option "defaults" or missing value usbfs: mount parameter error. starting pid 211, tty '': '-/bin/sh' BusyBox v1.17.2 (2013-09-18 18:56:34 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... chipinfo: module license 'proprietary' taints kernel. Disabling lock debugging due to kernel taint brcmchipinfo: brcm_chipinfo_init entry Broadcom Ingress QoS Module Char Driver v0.1 Sep 18 2013 18:52:06 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066320B (9MB), num of buffers=4766, buf size=2112 Broadcom BPM Module Char Driver v0.1 Sep 18 2013 18:52:05 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Sep 18 2013 18:52:07 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Sep 18 2013 18:52:07 bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6318B0 Ethernet Network Device v0.1 Sep 18 2013 18:53:42 ETH Init: Ch:0 - 200 tx BDs at 0xa2ffc000 ETH Init: Ch:1 - 200 tx BDs at 0xa2a37000 ETH Init: Ch:0 - 1906 rx BDs at 0xa3890000 ETH Init: Ch:1 - 100 rx BDs at 0xa39f4c00 Error: kerSysRegisterDyingGaspHandler: list head is null eth0: MAC Address: 68:15:90:EA:9B:46 eth1: MAC Address: 68:15:90:EA:9B:46 eth2: MAC Address: 68:15:90:EA:9B:46 eth3: MAC Address: 68:15:90:EA:9B:46 wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=3097 PCI: Enabling device 0000:02:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:02:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=256 otp_read_pci: bad crc Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm43131_vars.bin Failed to open srom image from '/etc/wlan/bcm43131_vars.bin'. wl:loading /etc/wlan/bcm43131_map.bin wl0: Broadcom BCMa8db 802.11 Wireless Controller 5.100.138.2008.cpe4.12L06B.4 Error: kerSysRegisterDyingGaspHandler: list head is null Broadcom 802.1Q VLAN Interface, v0.1 ===== Release Version 7.240 (build timestamp 130918_1854) ===== Got primary config file from flash (len=37410), validating.... wait instruction: enabled Netfilter messages via NETLINK v0.30. device eth1 entered promiscuous mode ADDRCONF(NETDEV_UP): eth1: link is not ready ip_tables: (C) 2000-2006 Netfilter Core Team ip6_tables: (C) 2000-2006 Netfilter Core Team device eth2 entered promiscuous mode ADDRCONF(NETDEV_UP): eth2: link is not ready device eth3 entered promiscuous mode ADDRCONF(NETDEV_UP): eth3: link is not ready device wl0 entered promiscuous mode WLmngr Daemon is running optarg=0 shmId=0 wlevt is ready for new msg... br0: port 4(wl0) entering forwarding state BcmAdsl_Initialize=0xC010F070, g_pFnNotifyCallback=0xC013A524 pSdramPHY=0xA3FFFFF8, 0xB07071F2 0xF0F2F0F3 *** XfaceOffset: 0x1C790 => 0x1C790 *** *** PhySdramSize got adjusted: 0x8F9D8 => 0xA561C *** AdslCoreSharedMemInit: shareMemSize=371133(371136) AdslCoreHwReset: pLocSbSta=820a0000 bkupThreshold=1600 AdslCoreHwReset: AdslOemDataAddr = 0xA3F84590 ***BcmDiagsMgrRegisterClient: 0 *** Error: kerSysRegisterDyingGaspHandler: list head is null bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system ADDRCONF(NETDEV_UP): eth0: link is not ready nf_conntrack version 0.5.0 (1008 buckets, 4032 max) rmmod: can't unload 'nf_nat_sip': unknown symbol in module, or unknown parameter rmmod: can't unload 'nf_conntrack_sip': unknown symbol in module, or unknown parameter monitor task is initialized pid= 304 There is no Predefined DevicePin in CFE WPS Device PIN = 16091399 rupgrade:error:18.052:ruReadMessageFromSmd:23:got SYSTEM_BOOT msg tr69c:error:18.768:cmsUtl_parseUrl:328:unrecognized host in URL http:// br0: port 4(wl0) entering disabled state device wl0 left promiscuous mode br0: port 4(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 4(wl0) entering forwarding state br0: port 4(wl0) entering disabled state Setting SSID: "SAGEMCOM_9B46" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" wlmngr_wlIfcDown: reset wifi_up_time wlmngr_wlIfcDown: reset wifi_up_time wlmngr_wlIfcDown: reset wifi_up_time wlmngr_wlIfcDown: reset wifi_up_time wlctl: Unsupported wlctl: Unsupported device wl0 left promiscuous mode br0: port 4(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 4(wl0) entering forwarding state acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0x2b0b wlmngr_wlIfcUp: wifi_up_time=29 BCM96318 Broadband Router Login: admin Password: > sh BusyBox v1.17.2 (2013-09-18 18:56:34 CST) built-in shell (ash) Enter 'help' for a list of built-in commands.


"Внутренний мир" официальной прошивки

cat version Linux version 2.6.30 (bensonli@sz01017.ads.local) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Wed Sep 18 18:54:02 CST 2013 # cat cpuinfo system type : F@ST1704N processor : 0 cpu model : Broadcom BCM3302 V3.3 BogoMIPS : 331.77 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : no hardware watchpoint : no ASEs implemented : shadow register sets : 1 core : 0 VCED exceptions : not available VCEI exceptions : not available unaligned exceptions : 0 # cat mounts rootfs / rootfs rw 0 0 /dev/root / squashfs ro,relatime 0 0 proc /proc proc rw,relatime 0 0 tmpfs /var tmpfs rw,relatime,size=420k 0 0 tmpfs /mnt tmpfs rw,relatime,size=16k 0 0 sysfs /sys sysfs rw,relatime 0 0 none /proc/bus/usb usbfs rw,relatime 0 0 # df Filesystem 1024-blocks Used Available Use% Mounted on /dev/root 6144 6144 0 100% / # ls /dev ac97 ippp0 ptyp2 sdb6 sdh3 bcm ippp1 ptyp3 sdb7 sdh4 bcm_omci isdn ptyp4 sdb8 si3215 bcm_ploam isdnctrl ptyp5 sdb9 slac bcm_user_ploam isdnctrl0 ptyp6 sdc spu bcmaal20 isdninfo ptyp7 sdc1 tty bcmadsl0 kmem ptyp8 sdc2 tty0 bcmadsl1 laser_dev ptyp9 sdc3 tty1 bcmarl linux-uk-proxy ptypa sdc4 ttyACM0 bcmatm0 linux-user-bde ptypb sdc5 ttyS0 bcmatmb0 log ptypc sdc6 ttyS1 bcmendpoint0 mem ptypd sdc7 ttyUSB0 bcmfap misc ptype sdc8 ttyUSB1 bcmles0 mtd0 ptypf sdc9 ttyUSB2 bcmmoca0 mtd1 pwrmngt sdd ttyUSB3 bcmmoca10 mtd2 ram sdd1 ttyUSB4 bcmprof mtd3 ram0 sdd2 ttyUSB5 bcmvdsl0 mtdblock0 ram1 sdd3 ttyp0 bcmvlan mtdblock1 ram2 sdd4 ttyp1 bcmxtmcfg0 mtdblock2 ram3 sde ttyp2 bounce mtdblock3 random sde1 ttyp3 bpm mtdblock4 sda sde2 ttyp4 brcmboard mtdblock5 sda1 sde3 ttyp5 capi20 mtdblock6 sda2 sde4 ttyp6 chipinfo mtdblock7 sda3 sdf ttyp7 console net sda4 sdf1 ttyp8 dect null sda5 sdf2 ttyp9 dectdbg p8021ag0 sda6 sdf3 ttypa dectshim pktcmf sda7 sdf4 ttypb ext_bonding pmon sda8 sdg ttypc fcache port sda9 sdg1 ttypd fuse ppp sdb sdg2 ttype gmac printer0 sdb1 sdg3 ttypf hwrandom ptm sdb2 sdg4 ubi0 i2c-0 pts sdb3 sdh ubi_ctrl ingqos ptyp0 sdb4 sdh1 urandom initctl ptyp1 sdb5 sdh2 zero #ls /bin acs_cli eapd mount smd acsd ebtables mroute sntp adsl echo nas sshd adslctl epi_ttcp nas4not ssk ash ethctl nbtscan stty bash ethswctl ntfs-3g tc bftpd false nvram telnetd bpm fast nvramUpdate tr69c bpmctl fc openl2tpd true brctl fcctl openssl udhcpd busybox grep ping umount cat hotplug ping6 upnp chmod httpd pppd urlfilterd consoled ip ps usb_modeswitch cp ip6tables pwd vlanctl date ippd pwr wl ddnsd iptables pwrctl wl_server df iq radvd wl_server_socket dhcp6c iqctl rawSocketTest wlctl dhcp6s kill ripd wlevt dhcpc lld2d rm wlmngr dhcpd ln rupgrade wps_monitor diag_ping ls scriptDaemon xdslctl dmesg mcp setmem xtm dnsproxy mcpctl sh xtmctl dnsspoof mcpd sleep zebra dsldiagd mkdir smbd dumpmem mknod smbpasswd #ls /sbin depmod hotplug insmod modprobe rmmod syslogd ethctl ifconfig klogd poweroff route vconfig halt init logread reboot sysinfo #ls / bin dev lib mnt proc sys usr webs data etc linuxrc opt sbin tmp var webs-RS # cd /mnt # ls /usr bin # ls /usr/bin [ chat ftpget patch tftp tty [[ chrt killall sendarp tftpd wget arping cmp logger taskset top xargs awk expr nc test traceroute # ps PID USER VSZ STAT COMMAND 1 admin 1592 S init 2 admin 0 SW< [kthreadd] 3 admin 0 SW [sirq-high/0] 4 admin 0 SW [sirq-timer/0] 5 admin 0 SW [sirq-net-tx/0] 6 admin 0 SW [sirq-net-rx/0] 7 admin 0 SW [sirq-block/0] 8 admin 0 SW [sirq-tasklet/0] 9 admin 0 SW [sirq-sched/0] 10 admin 0 SW [sirq-hrtimer/0] 11 admin 0 SW [sirq-rcu/0] 12 admin 0 SW< [events/0] 13 admin 0 SW< [khelper] 16 admin 0 SW< [async/mgr] 70 admin 0 SW< [kblockd/0] 79 admin 0 SW< [khubd] 110 admin 0 SW [pdflush] 111 admin 0 SW [pdflush] 112 admin 0 SWN [kswapd0] 114 admin 0 SW< [crypto/0] 172 admin 0 SW< [mtdblockd] 202 admin 0 SW< [linkwatch] 211 admin 1608 S -/bin/sh 252 admin 0 SW [dsl0] 271 admin 0 SW [bcmsw] 272 admin 0 SW [bcmsw_timer] 303 admin 3876 S smd 304 admin 5616 S ssk 321 admin 1440 S dhcpd 345 admin 4004 S mcpd 627 admin 5196 S wlmngr -m 0 644 admin 1332 S /bin/wlevt 695 admin 1440 S dsldiagd 696 admin 4420 S rupgrade -m 0 724 admin 5244 S /bin/smbd -D 768 admin 5244 S /bin/smbd -D 808 admin 848 S radvd -C /var/radvd.conf 828 admin 1244 S /bin/lld2d br0 832 admin 1168 S /bin/eapd 842 admin 1316 S /bin/nas 852 admin 1248 S /bin/acsd 854 admin 2668 S /bin/wps_monitor 921 admin 1392 S dnsproxy 942 admin 4356 S consoled -m 0 997 admin 1588 S sh -c sh 998 admin 1600 S sh 1058 admin 1592 R ps # ls /etc 12d1:1001 dhcp6s.conf.sample lmhosts samba 12d1:1003 dms.conf mdk services 12d1:1446 dyndscp.sh modules_install smb.conf 12d1:14fe ethertypes mtab snmp 12d1:1505 filesystems passwd soft_bridge 19d2:1216 fstab ppp sysmsg 19d2:2000 gateway.conf pppmsg udhcpd.conf 19d2:fff5 group printcap udhcpd.leases 1bbb:f000 inetd.conf profile vlan adsl init.d psk.txt wlan arl inittab racoon.conf wrt54g.large.ico arlflush iproute2 radvd.conf.sample wrt54g.small.ico dhcp ipsec.conf resolv.conf dhcp6c.conf.sample ipv6_start.sample rsa_host_key # cat /etc/fstab proc /proc proc defaults 0 0 tmpfs /var tmpfs size=420k 0 0 tmpfs /mnt tmpfs size=16k 0 0 sysfs /sys sysfs defaults 0 0 none /proc/bus/usb usbfs defaults 0 0 # ls /bin acs_cli eapd mount smd acsd ebtables mroute sntp adsl echo nas sshd adslctl epi_ttcp nas4not ssk ash ethctl nbtscan stty bash ethswctl ntfs-3g tc bftpd false nvram telnetd bpm fast nvramUpdate tr69c bpmctl fc openl2tpd true brctl fcctl openssl udhcpd busybox grep ping umount cat hotplug ping6 upnp chmod httpd pppd urlfilterd consoled ip ps usb_modeswitch cp ip6tables pwd vlanctl date ippd pwr wl ddnsd iptables pwrctl wl_server df iq radvd wl_server_socket dhcp6c iqctl rawSocketTest wlctl dhcp6s kill ripd wlevt dhcpc lld2d rm wlmngr dhcpd ln rupgrade wps_monitor diag_ping ls scriptDaemon xdslctl dmesg mcp setmem xtm dnsproxy mcpctl sh xtmctl dnsspoof mcpd sleep zebra dsldiagd mkdir smbd dumpmem mknod smbpasswd # zebra


Tags

ru/toh/sagem/fast2804.txt · Last modified: 2016/10/11 19:52 by tmomas