Actiontec GT724WG
The device is based on Texas Instrument AR7. It seems to boot the 10.3 kernels, but work is still needed for it to be useful.
Hardware Highlights
| CPU | Ram | Flash | Network | USB | Serial | JTag |
|---|---|---|---|---|---|---|
| TI AR7@212MHz | 16MB | 4MB | 4 + DSL + WiFi(TI TNETW1350A) Marvel 88E6060 switch | No | Yes | Yes? |
Photo
Flash layout
| partition | start | end | description |
|---|---|---|---|
| mtd2 | 0x90000000 | 0x90010000 | ADAM2 bootloader |
| mtd1 | 0x90020000 | 0x90100000 | kernel |
| mtd0 | 0x90100000 | 0x902c0000 | squashfs filesystem |
| mtd4 | 0x90020000 | 0x902c0000 | unused to load image |
| mtd3 | 0x90010000 | 0x90020000 | ADAM2 environment |
Boot loader
PSPBoot1.3 rev: 1.3.7.15
Serial
3.3V serial is available on JP603 with the following pin out:
pin 1 : GND pin 2 : TX pin 3 : RX pin 4 : NC pin 5 : 3.3V pin 6 : NC
Pin 1 is the closest to LED9.
Boot output
PSPBoot1.3 rev: 1.3.7.15
(c) Copyright 2002-2005 Texas Instruments, Inc. All Rights Reserved.
Press ESC for monitor... 1
(psbl)
Booting...
Linux version 2.6.32.25 (openwrt@ampere) (gcc version 4.3.3 (GCC) ) #1 Fri Nov 19 20:11:33 PST 2010
bootconsole [early0] enabled
CPU revision is: 00018448 (MIPS 4KEc)
TI AR7 (TNETD7200), ID: 0x002b, Revision: 0x11
Determined physical RAM map:
memory: 01000000 @ 14000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00014000 -> 0x00015000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00014000 -> 0x00015000
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: rootfstype=squashfs,jffs2 console=ttyS0,38400n8
PID hash table entries: 64 (order: -4, 256 bytes)
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, VIPT, no aliases, linesize 16 bytes
Memory: 12352k/16384k available (2254k kernel code, 4032k reserved, 353k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:256
Clocks: Sync 2:1 mode
Clocks: Setting CPU clock
Adjusted requested frequency 211000000 to 211968000
Clocks: base = 35328000, frequency = 211968000, prediv = 1, postdiv = 1, postdiv2 = -1, mul = 6
Clocks: Setting DSP clock
Clocks: base = 25000000, frequency = 105984000, prediv = 1, postdiv = 2, postdiv2 = 1, mul = 10
Clocks: Setting USB clock
Adjusted requested frequency 48000000 to 47863741
Clocks: base = 105984000, frequency = 48000000, prediv = 1, postdiv = 31, postdiv2 = -1, mul = 14
Calibrating delay loop... 211.35 BogoMIPS (lpj=1056768)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
msgmni has been set to 24
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a TI-AR7
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
physmap platform flash device: 00800000 at 10000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
CFI mfr 0x000000ec
CFI id 0x000022a2
Amd/Fujitsu Extended Query Table at 0x0040
Newer Samsung flash detected, should be compatibile with Amd/Fujitsu.
Fixed Samsung's Amd/Fujitsu Extended Query version from 3.3 to 1.3.
Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
4 ar7part partitions found on MTD device physmap-flash.0
Creating 4 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000010000 : "loader"
0x000000010000-0x000000020000 : "config"
0x000000020000-0x000000400000 : "linux"
0x000000100000-0x000000400000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2B0000, len=150000
0x0000002b0000-0x000000400000 : "rootfs_data"
Fixed MDIO Bus: probed
cpmac-mii: probed
cpmac: device eth0 (regs: 08610000, irq: 27, phy: 1:10, mac: 00:15:05:d3:00:00)
ar7_wdt: timer margin 59 seconds (prescale 65535, change 48480, freq 52992000)
Registered led device: status
vlynq0: regs 0x08611800, irq 29, mem 0x04000000
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
Freeing unused kernel memory: 136k freed
Please be patient, while OpenWrt loads ...
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
mini_fo: using base directory: /
mini_fo: using storage directory: /tmp/root
- init -
Please press Enter to activate this console. device eth0 entered promiscuous mode
br-lan: port 1(eth0) entering forwarding state
br-lan: port 1(eth0) entering disabled state
BusyBox v1.15.3 (2010-11-11 22:17:14 PST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
Backfire (10.03.1-rc4, r24045) --------------------
* 1/3 shot Kahlua In a shot glass, layer Kahlua
* 1/3 shot Bailey's on the bottom, then Bailey's,
* 1/3 shot Vodka then Vodka.
---------------------------------------------------
root@OpenWrt:/# NET: Registered protocol family 8
NET: Registered protocol family 20
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 24
nf_conntrack version 0.5.0 (195 buckets, 780 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
acx: this driver is still EXPERIMENTAL
acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion
acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
acx: running on a little-endian CPU
acx: PCI/VLYNQ module v0.3.37 initialized, waiting for cards to probe...
registered device TI Avalanche SAR
Ohio250(7200/7100A2) detected
requesting firmware image "ar0700xx.bin"
avsar: firmware: requesting ar0700xx.bin
tn7dsl_set_modulation : Setting mode to 0x1
Creating new root folder avalanche in the proc for the driver stats
Texas Instruments ATM driver: version:[7.03.01.00]
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
mini_fo: using base directory: /
mini_fo: using storage directory: /overlay
ar7_wdt: timer margin 59 seconds (prescale 65535, change 48480, freq 52992000)
root@OpenWrt:/#
Original Vendor Firmware Boot Log
(psbl) printenv
BUILD_OPS 0x301
bootloaderVersion 1.3.7.15
SerialNumber none
MEMSZ 0x01000000
FLASHSZ 0x00400000
CPUFREQ 211968000
MIPSFREQ 211968000
SYSFREQ 105984000
PROMPT (psbl)
BOOTCFG m:f:"mtd1"
mtd2 0x90000000,0x90010000
mtd3 0x90010000,0x90020000
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
modulation 1
AEIBootVersion 1.0
mtd1 0x90020000,0x900c0000
mtd4 0x903f0000,0x90400000
HWRevision 3A
usb_vid 0x1668
usb_pid 0x6010
MODETTY0 38400,n,8,1,hw
MODETTY1 38400,n,8,1,hw
MAC_PORT 1
DSL_FEATURE_CNTL_0 0x00002000
DSL_PHY_CNTL_0 0x00000200
ProductID GT724WGR
IPA_SVR 192.168.0.99
NVS_TFTP_LOAD 0
HWA_0 00:15:05:D3:16:B2
WLAN_HWADDR 00:15:05:D3:16:B2
HWA_3 00:15:05:D3:16:B3
WLAN_EEPROM0 021156041B06001200000701095612000000010D56A9000000026D541C0CD901
WLAN_EEPROM1 18000000013984000100000101854C1068900105850600100001298507000000
WLAN_EEPROM2 01C1850000300001C585000000000111850000FFFF0115850000F0FF01A58500
WLAN_EEPROM3 8000000109850000800201010C03000000012184000000800181851D00030001
WLAN_EEPROM4 55090100000001E5580200000001F1580800000001D5581000000001B1580400
WLAN_EEPROM5 0000000000000000000C00C300FE0008011401260144014D014F0165019F01AF
WLAN_EEPROM6 01B70101390000110004010101000501060002010201021E000A000205020411
WLAN_EEPROM7 2244030610203031324004095449204143583130300507544920546573740108
WLAN_EEPROM8 170B097CB25C01220502000038007000A900E50004044410E7034510F303185A
WLAN_EEPROM9 4000145A2D00020E0801F0000A017C034600A1018509500009010A010D044600
WLAN_EEPROM10 9F0185090107100000400000010000050400010100000000FFFFFFFFFDFDFDFD
WLAN_EEPROM11 FBF4F4F4F40E04FDFDFDFEFFFFFFFF090000FF09090909090909090909090909
WLAN_EEPROM12 0909090909090909000009FFFFFFFEFDFDFDFE0909090909090909090909090E
WLAN_EEPROM13 0100000000000000000000000000000302A318A3180700012000000000000000
WLAN_EEPROM14 00000000000000000000000000000000000000000000000000
HWA_RNDIS 00:15:05:D3:16:B2
HWA_HRNDIS 00:15:05:D3:16:B2
IPA 192.168.0.1
mtd0 0x900c0000,0x903c0000
mtd5 0x903c0000,0x903f0000
defaults
connection0 0xd83c
(psbl) fa
Current Flash Allocation:
section : PSBL, base : 0xb0000000, size : 65136 bytes
section : ENV, base : 0xb0010000, size : 65535 bytes
unallocated Space Start: 0xb0020000
unallocated Space End : 0xb0400000
(psbl) oclk -d
CPU Frequency: 211968000Hz
SYSTEM Frequency: 105984000Hz
Basic POST completed... Success.
Last reset cause: Hardware reset (Power-on reset)
PSPBoot1.3 rev: 1.3.7.15
(c) Copyright 2002-2005 Texas Instruments, Inc. All Rights Reserved.
Press ESC for monitor... 1
(psbl)
Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2003 Texas Instruments Incorporated; Copyright (C) 1999-2003 Igor Pavlov.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.
LINUX started...
Config serial console: ttyS0,38400
Auto Detection OHIO chip
This SOC has MDIX cababilities on chip.
WLAN 1350 chip configured.
Do not defined CONFIG_AVALANCHE_VLYNQ_POLARITY_LOW
Success in setting up the VLYNQ.
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 8kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (ncs@localhost.localdomain) (gcc version 2.95.3 20010315 (release/MontaVista)) #1 Wed Jul 30 12:30:45 PDT 2008
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 00102c00(1059840)
CPU frequency 211.97 MHz
Calibrating delay loop... 211.35 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 14248k/16384k available (1606k kernel code, 2136k reserved, 107k data, 64k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
--------init push-----
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 120
Using 120 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
Installed misc driver vlynq0: it handles vlynq bridge0 with 1 hop(s).
block: 64 slots per queue, batch=16
DEBUG: Initializing the voice port management module.
DEBUG: Initialization of the voice port management module successful..
Error getting CPMAC Configuration params for instance:0
Environment Variable:MACCFG_A not set in bootloader
Setting Default configuration params for CPMAC instance:0
TI CPMAC Linux DDA version 1.8 - CPMAC DDC version 0.2
Cpmac: Installed 1 instances.
Cpmac driver is allocating buffer memory at init time.
PPP generic driver version 2.4.1
imq driver loaded.
avalanche flash device: 0x400000 at 0x10000000.
Amd/Fujitsu Extended Query Table v3.3 at 0x0040
number of CFI chips: 1
Looking for mtd device :mtd0:
Found a mtd0 image (0xc0000), with size (0x300000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x000c0000-0x003c0000 : "mtd0"
Looking for mtd device :mtd1:
Found a mtd1 image (0x20000), with size (0xa0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x000c0000 : "mtd1"
Looking for mtd device :mtd2:
Found a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Looking for mtd device :mtd3:
Found a mtd3 image (0x10000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x00020000 : "mtd3"
Looking for mtd device :mtd4:
Found a mtd4 image (0x3f0000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x003f0000-0x00400000 : "mtd4"
Looking for mtd device :mtd5:
Found a mtd5 image (0x3c0000), with size (0x30000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x003c0000-0x003f0000 : "mtd5"
Looking for mtd device :mtd6:
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
Linux IP multicast router 0.06 plus PIM-SM
****ip_conntrack version 2.0 (128 buckets, 1024 max) - 384 bytes per conntrack
ip_tables: (c)2000 Netfilter core team
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 64k freed
serial console detected. Disabling virtual terminals.
init started: BusyBox v0.61.pre (2008.07.30-19:33+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
/bin/cp /etc/ppp/* /var/etc/ppp
cp: /etc/ppp/resolv.conf: No such file or directory
cp: /etc/dproxy.conf: No such file or directory
cp: /etc/dropbear: omitting directory
cp: /etc/gateways: No such file or directory
cp: /etc/hosts: No such file or directory
cp: /etc/init.d: omitting directory
cp: /etc/linux-igd: No such file or directory
cp: /etc/passwd: No such file or directory
cp: /etc/ppp: omitting directory
cp: /etc/resolv.conf: No such file or directory
cp: /etc/shadow: No such file or directory
cp: /etc/udhcpc: omitting directory
cp: /etc/udhcpd.conf: No such file or directory
cp: /etc/localhosts: No such file or directory
cp: /usr/www/html/pc_*.html: No such file or directory
Reading Standard Configuration File /etc/led.conf
Configured 50 states
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o
registered device TI Avalanche SAR
Ohio250(7200/7100A2) detected
DSP binary filesize = 390290 bytes
tn7dsl_set_modulation : Setting mode to 0x1
Texas Instruments ATM driver: version:[7.04.03.00]
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Please press Enter to activate this console. Using default config 1
-----wlan load.
2--- ssid = Actiontec,0, adding=0
$$$-AP Acquiring Lock
ap_settings created
vmode=0
vip=0.0.0.0
vmode=(null)
vip=(null)
vmode=(null)
vip=(null)
******dhcpd is on
logic init (test kprintf)...
$$$-wlan_handle_load_event - Acquired Lock
2-Boot_Default= 1, 0
ap_settings created for default
3-config ssid = Actiontec,0
Query eth0
Query usb0
Query eth0
Query usb0
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
creating lan_settings
$$$-WPA Authenticator Started
insmod tiap.o......
initTnetwAddr: MemAddr=0xa4000000, RegAddr=0xa4080000
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
wpa_authenticat uses obsolete (PF_INET,SOCK_PACKET)
187:
802.11d is 187: disabled.
187: 802.11h is 187: disabled.
187: For SSID 0 vlan tag received is 0
187: wdrv_dbMainInit : WME disabled
187: wdrv_dbMainInit: wdsEnabled=0
187: Configuration succeeded !!!
187: WLAN driver database is up
ACX Hard reset!!!
Preparing for vlynq tearing down....
Resetting the remote device.
Un-resetting the remote device.
Preparing the VLYNQ, now the Link is up.
initTnetwAddr: MemAddr=0xa4000000, RegAddr=0xa4080000
188: AcxRegAddr = 0xA4080000, AcxMemAddr = 0xA4000000
188: whal_ParamsInitDmaParams:303 wone = 0 queues = 2
189: whal_acxProcInitiate: Got CHIP_ID = 0x6010101
189: ***** EepromlessSupport !!!!!!!!!
189: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x5610 Data 0x61b04
189: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x5614 Data 0x7000012
189: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x5608 Data 0x12
189: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x560c Data 0xa9
190: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x546c Data 0x1d90c1c
190: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x5470 Data 0x18
190: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x8438 Data 0x100
190: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x8500 Data 0x9068104c
190: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x8504 Data 0x100006
190: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x8528 Data 0x7
191: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x85c0 Data 0x300000
191: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x85c4 Data 0x0
191: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x8510 Data 0xffff0000
191: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x8514 Data 0xfff00000
191: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x85a4 Data 0x8000
191: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x8508 Data 0x2800000
192: whal_hwCtrl_ProcessEepromBREntry: Reg = 0xc00 Data 0x3
192: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x8420 Data 0x80000000
192: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x8580 Data 0x3001d
192: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x954 Data 0x1
192: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x58e4 Data 0x2
192: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x58f0 Data 0x8
193: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x58d4 Data 0x10
193: whal_hwCtrl_ProcessEepromBREntry: Reg = 0x58b0 Data 0x4
193: whal_hwCtrl_ProcessEepromBR : CurrEepromBufPtr = 0xc
193: whal_hwCtrl_GetNvsDataSize: eepromImage.len = 0x1d9 193: Get NVS file information: NvsDataLen = 0x134 tblsOffset 0xa9
193: whal_acxProcInitiate: Cpu halt -> download code
194: whal_acxProcLoadFwImage: 0xa4000000, 0x0
194: whal_acxProcLoadFwImage() -- Loading FW image
194: Compiled for DCR radio
194: whal_acxProcLoadFwImage: 1, pBuf=0xc00b2640, len=0x14e78. Extra pBuf=0x0, len=0x0
194: whal_acxProcLoadFwImage: 2, pBuf=0xc00b2640, len=0x14e78. Extra pBuf=0x0, len=0x0
194: whal_acxProcLoadFwImage: 3, pBuf=0xc00b2640, len=0x14e78, DataLen=0x14e70
195: whal_acxProcLoadFwImage: 4, pBuf=0xc00b2640, len=0x14e78
195: whal_acxProcLoadFwImage: Checksum, calc=0x6f5149, file=0x6f5149
ACX111 VL Remote Base 0x60000000
198: whal_acxProcInitiate: Run
199: whal_hwCtrl_WaitFwWhenEepromless: WaitRegVal = 0x134
199: GOT HANDSHAKE FROM FIRMWARE !!!! WaitRegVal = 0x22bcc
199: whal_hwCtrl_CopyNvsData: 1
199: whal_acxProcWaitInitComplete:
200: whal_acxProcInitiate: Firmware is running...
200: whal_acxMboxInit: pCmdMbox=0xa4022d00, pInfoMbox=0xa4022b2c
200: ----------------------------------------------------------------
200: ACX Firmaware Version = Rev 3.3.0.6A
200: EEPROM Version = 6.0.7
201: ----------------------------------------------------------------
201: whal_acxProcConfigure: templates (beacon, probe response, tim) for [0] Network
201: whal_acxProcConfigure: Host Queue is in 0x94840020
201: TxQueue[0] NumDesc = 32
201: TxQueue[0] Priority = 0
201: TxQueue[1] NumDesc = 32
201: TxQueue[1] Priority = 129
201:
whal_acxConfigMemory() --
HostRxDescriptorsAddr = 14840020
202: RxQueue NumDesc = 32
202: RxQueue Priority = 0
202: RxQueue type = 7
202: Rx (requested) NumBlk = 52
202: Tx (requested) NumBlk = 50
202:
202: whal_acxProcConfigure: read queue heads
203: whal_acxConfigRead_QueueHead() -
203: RxMemBlkQ - 000152e0
203: RxQueueHead - 000128d0
203: TxMemBlkQ - 000186e0
203: TxMemBlkQ[0]- 00012dd0
203: TxMemBlkQ[1]- 000132d0
203: whal_acxProcConfigure: configure RxQueue/TxQueue objects
203: whal_txQueue_Init: [Qid=0] HwBaseAddr=0xa4012dd0, NumDesc=32
204: whal_acxConfigAccessCategory : acID = 1
=> AIFSN = 2, cwMin = 15, cwMax = 1023
=> TxOpLimit = 0, TxOpCont = 0, rxTimeout = 0
=> Short Retry = 7, Long Retry = 4, Retry preemt = 0
204: whal_acxProcConfigure: AC=1
204: whal_acxProcConfigure: Qud=0 Guaranteed threshold = 17, High threshold = 65 blocks
205: whal_txQueue_Init: [Qid=1] HwBaseAddr=0xa40132d0, NumDesc=32
205: whal_acxProcConfigure: AC=4
205: whal_acxProcConfigure: Qud=1 Guaranteed threshold = 7, High threshold = 21 blocks
206: whal_ParamsPrintMemMap:
206: Code (0x00000000, 0x00011d04)
Wep (0x00011f80, 0x00012010)
Sta (0x00012010, 0x00012738)
Tmpl (0x00011d24, 0x00011d5c)
Queue (0x000128d0, 0x000137d0)
Pool (0x000152e0, 0x000224e0)
206: Dbg1 (0x00000000, 0x00000000)
Dbg2 (0x00000000, 0x00000000)
TxBlocks (158)
RxBlocks (52)
208: whal_apiConfig: beaconInterval = 200
WATCH_DOG_TIMER_VAL = 520
wd_beacon_limiter = 2
txStuckThreshold = 3
209: WLAN HAL layer is up
209: BssBridge is up
209: Mgmt is up
209: Rx is up
209: wdrv_txInit: AC = 0 size = 187
209: wdrv_txInit: AC = 3 size = 192
209: Tx is up
209: MemMngr is up
209: main state machine is up
209: QoS module is up is up
230: WDRV_MAINSM: WLAN Driver initialized successfully
230: WDRV_4X: 4x Disabled
230: WDRV_4X: Concatenation Disabled
230: WDRV_4X: Ack Emulation Disabled
230: whal_apiStartBss: Enable Tx, Rx and Start the Bss
230: ----------------------------------------------------------------
230: ----------------------------------------------------------------
231: START BSS, SSID=Actiontec, BSSID=00-15-05-D3-16-B2
231: ----------------------------------------------------------------
231: ----------------------------------------------------------------
231: AP Power Level = 1
231: Regulatory Domain = FCC
231: Net[0] : Channel=9
231: ----------------------------------------------------------------
232: FW Watchdog is Enabled
dda: wlan0 in initializing Succeeded wireless extensions: ret = 0
wlan0 device is activated
call act_box 3 20
Query wbif0
device wbif0 entered promiscuous mode
br0: port 2(wbif0) entering learning state
creating lan_settings
br0: port 2(wbif0) entering forwarding state
br0: topology change detected, propagating
---got lan_ip 192.168.0.1,11
BusyBox v0.61.pre (2008.07.30-19:33+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
# ifconfig
br0 Link encap:Ethernet HWaddr 00:15:05:D3:16:B2
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ASYMMTU:1500
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:13 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:582 (582.0 b)
br1 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ASYMMTU:1500
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
br2 Link encap:Ethernet HWaddr 00:00:00:00:00:00
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ASYMMTU:1500
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
eth0 Link encap:Ethernet HWaddr 00:15:05:D3:16:B2
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ASYMMTU:1500
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:200 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:11802 (11.5 kb)
imq0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00
UP RUNNING NOARP MTU:1500 Metric:1 ASYMMTU:1500
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1 ASYMMTU:0
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
wbif0 Link encap:Ethernet HWaddr 00:E0:A6:66:51:EB
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ASYMMTU:1500
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:196 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:11562 (11.2 kb)
wlan0 Link encap:Ethernet HWaddr 00:15:05:D3:16:B2
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 ASYMMTU:1500
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:196 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:11562 (11.2 kb)
#
toh/actiontec/gt724wg.txt · Last modified: 2010/12/15 04:07 by mk2s