User Tools

Site Tools


toh:actiontec:gt784wnv

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
toh:actiontec:gt784wnv [2013/03/11 14:45]
sycophantic
toh:actiontec:gt784wnv [2016/04/21 16:02] (current)
danitool [GPIO]
Line 1: Line 1:
 +====== Actiontec GT784WNV ======
  
 +{{media:​actiontec:​gt784wnv_case.png|}}
 +
 +The MAC address is initialized to all zeroes, which prevents normal config. It can be set manually, after which wireless works.
 +
 +The device doesn'​t appear to have SPROM.
 +<​code>​
 +[    9.836000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
 +[    9.884000] bcma: bus0: invalid sprom read from the PCIe card, try to use fallback sprom
 +[    9.892000] bcma: bus0: Using fallback SPROM failed (err -2)
 +[    9.900000] bcma: bus0: No SPROM available
 +</​code>​
 +===== Supported Versions =====
 +---- datatable ----
 +cols    : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, Forum Topic URL_url, Device Techdata_pageid
 +headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data
 +align   : c,​c,​c,​c,​c,​c,​c,​c
 +filter ​ : Brand=Actiontec
 +filter ​ : Model=GT784WNV
 +----
 +
 +===== Hardware Highlights =====
 +---- datatable ----
 +cols    : Model, Versions, Platform, CPU MHz, Flash MB_mbflashs,​ RAM MB_mbram, WLAN Hardware, WLAN 2.4Ghz, WLAN 5.0Ghz, Ethernet 100M ports_, Ethernet Gbit ports_, Modem, USB ports_
 +header ​ : Model, Version,​SoC,​CPU MHz,Flash MB,RAM MB,WLAN Hardware,​WLAN2.4,​WLAN5.0,​100M ports,Gbit ports,​Modem,​USB
 +align   : c,​c,​c,​c,​c,​c,​c,​c,​c,​c,​c,​c
 +filter ​ : Brand=Actiontec
 +filter ​ : Model=GT784WNV
 +sort    : version
 +----
 +
 +===== Installation =====
 +  - → [[doc:​howto:​obtain.firmware|Obtain firmware]]
 +  - → [[doc:​howto:​generic.flashing|Install OpenWrt]]
 +  - → [[about:​latest|Latest OpenWrt release]]
 +
 +---- datatable ----
 +cols    : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url
 +align   : l,c,c
 +filter ​ : Brand=Actiontec
 +filter ​ : Model=GT784WNV
 +sort    : version
 +----
 +
 +==== Flash Layout ​ ====
 +
 +^ Layer0 |  S25FL128 16384KiB ​ |||||
 +^ Layer1 |  mtd0\\ **//​CFE//​**\\ 64 KiB  |  mtd5\\ **//''​linux''//​**\\ 16256 KiB |||  mtd4\\ **//​nvram//​**\\ 64 KiB |
 +^ Layer2 |  |  mtd1\\ **//​kernel//​**\\ ​ 1213 KiB  | mtd2\\ **''​rootfs''​** \\ 15042 KiB \\ mounted: "''/''",​ [[doc:​techref:​filesystems#​overlayfs|OverlayFS]] with ''/​overlay'' ​ ||
 +^ Layer3 |  |  |  **''/​dev/​root''​** \\ mounted: "''/​rom''",​ [[doc:​techref:​filesystems#​SquashFS|SquashFS]] \\ 1792 KiB |  mtd3\\ **''​rootfs_data''​** \\ mounted: "''/​overlay''",​ [[doc:​techref:​filesystems#​SquashFS|JFFS2]] \\ "​free"​ space 13440 KiB |
 +
 +==== OEM easy installation via CFE  ====
 +   - → [[doc:​techref:​bootloader:​cfe#​using_cfe_web_http_server|CFE Http Server]]
 +
 +==== OEM easy installation via tftp  ====
 +   - → [[doc:​techref:​bootloader:​cfe#​using_cfe_tftp_client|CFE TFTP Client]]
 +
 +===== Upgrading OpenWrt =====
 +->  [[doc:​howto:​generic.sysupgrade]]
 +
 +==== LuCI Web Upgrade Process ====
 +
 +  * Browse to http://​192.168.1.1/​cgi-bin/​luci/​mini/​system/​upgrade/​ LuCI Upgrade URL
 +  * Upload image file for sysupgrade to LuCI
 +  * Wait for reboot
 +
 +==== Terminal Upgrade Process ====
 +
 +If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line.
 +
 +=== sysupgrade ===
 +
 +  * Login as root via SSH on 192.168.1.1,​ then enter the following commands:
 +
 +<​code>​
 +cd /tmp
 +wget http://​downloads.openwrt.org/​snapshots/​trunk/​XXX/​xxx.abc
 +sysupgrade /​tmp/​xxx.abc
 +</​code>​
 +
 +===== Debricking =====
 +-> [[doc:​howto:​generic.debrick]]
 +
 +===== Failsafe mode =====
 +-> [[doc:​howto:​generic.failsafe]]
 +
 +===== Basic configuration =====
 +-> [[doc:​howto:​basic.config|Basic configuration]] After flashing, proceed with this.\\
 +Set up your Internet connection, configure wireless, configure USB port, etc.
 +
 +===== Specific Configuration =====
 +
 +==== Network interfaces ====
 +The default network configuration is:
 +^ Interface Name   ^ Description ​                 ^ Default configuration ​   ^
 +| br-lan ​          | LAN & WiFi                   | 192.168.1.1/​24 ​          |
 +| vlan1 (eth0.1) ​  | LAN ports (1 to 4)           | None                     |
 +| wl0              | WiFi (after install of kmod-brcmsmac) | Disabled ​                |
 +
 +
 +==== Switch Ports (for VLANs) ====
 +
 +Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.
 +^ Port             ^ Switch port   ^
 +| LAN 1            | 0     |
 +| LAN 2            | 1     |
 +| LAN 3            | 2     |
 +| LAN 4            | 3     |
 +
 +
 +===== Hardware =====
 +---- datatemplatelist dttpllist ----
 +template: meta:​template_datatemplatelist
 +cols    : Brand, Model, Versions, Device Type, Availability,​ Supported Since Rev, Supported since Rel, Supported current Rel,  Instruction Set, Sub Instruction Set, Bootloader, Platform, Target, CPU MHz, Flash MBs, RAM MB, Switch, Ethernet 100M ports_, Ethernet Gbit ports_, Comments network ports_, Modem, VLAN, WLAN 2.4GHz, WLAN 5.0GHz, WLAN Comments_, Detachable Antennas_, USB ports_, SATA ports_, Comments USB SATA ports_, Serial, JTAG, LED count, Button count, Device Techdata_pageid,​ Forum topic URL_url, wikidevi URL_url, OEM Device Homepage URL_url, Firmware OEM Stock URL_url, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Comments_
 +filter ​ : Brand=Actiontec
 +filter ​ : Model=GT784WNV
 +----
 +
 +==== Photos ====
 +==== Case / Housing ====
 +//Housing//
 +
 +
 +==== Opening the case ====
 +**Note:** This will void your warranty!
 +
 +**Main PCB**
 +
 +{{media:​actiontec:​gt784wnv_mainpcb.png?​450x280|}} ​ {{media:​actiontec:​gt784wnv_mainpcb-back.png?​450x280|}} ​
 +
 +==== Serial ====
 +-> [[doc:​hardware:​port.serial]] general information about the serial port, serial port cable, etc.
 +
 +Settings: 115200, 8N1, no software flow control, no hardware flow control.
 +
 +3.3V serial is available on JP1 with the following pin out:
 +
 +<​code>​
 +pin 1 : GND
 +pin 2 : TX
 +pin 3 : RX
 +pin 4 : NC
 +pin 5 : 3.3V
 +pin 6 : NC
 +</​code>​
 +
 +Pin 1 is the closest to R78. 
 +
 +
 +How to connect to the Serial Port of this specific device:
 +
 +**Photo of PCB with markings**
 +
 +==== JTAG ====
 +-> [[doc:​hardware:​port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +How to connect to the JTAG Port of this specific device:
 +
 +**Photo of PCB with markings**
 +==== GPIO ====
 +-> [[doc:​hardware:​port.gpio]]
 +
 +GPIOs available for use on this device are:
 +^ GPIO# ^ BCM6328 pin ^ Function ^
 +| 480 | 0 | ? |
 +| 481 | 1 | Green Internet LED |
 +| 482 | 2 | ? |
 +| 483 | 3 | ? |
 +| 484 | 4 | ? |
 +| 485 | 5 | ? |
 +| 486 | 6 | ? |
 +| 487 | 7 | Red Internet LED |
 +| 488 | 8 | ? |
 +| 489 | 9 | ? |
 +| 490 | 10 | ? |
 +| 491 | 11 | ? |
 +| 492 | 12 | ? |
 +| 493 | 13 | ? |
 +| 494 | 14 | ? |
 +| 495 | 15 | ? |
 +| 496 | 16 | ? |
 +| 497 | 17 | ? |
 +| 498 | 18 | Yellow Power LED |
 +| 499 | 19 | Green DSL LED |
 +| 500 | 20 | Turn off Wireless? |
 +| 501 | 21 | ? |
 +| 502 | 22 | ? |
 +| 503 | 23 | ? |
 +| 504 | 24 | ? |
 +| 505 | 25 | ? |
 +| 506 | 26 | ? |
 +| 507 | 27 | ? |
 +| 508 | 28 | ? |
 +| 509 | 29 | Green WPS LED |
 +| 510 | 30 | ? |
 +| 511 | 31 | Red WPS LED |
 +
 +===== Bootlogs =====
 +==== OEM bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​HELO
 +CPUI
 +L1CI
 +DRAM
 +----
 +PHYS
 +ZQDN
 +PHYE
 +DINT
 +LSYN
 +USYN
 +MSYN
 +LMBE
 +PASS
 +----
 +ZBSS
 +CODE
 +DATA
 +L12F
 +MAIN
 +
 +
 +CFE version 1.0.37-106.17 for BCM96328 (32bit,​SP,​BE)
 +Build Date: Wed Jun 15 15:48:10 PDT 2011 (root@localhost.localdomain)
 +Copyright (C) 2000-2009 Broadcom Corporation.
 +
 +HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
 +Total Flash size: 16384K with 256 sectors
 +Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 67108864 bytes (64MB)
 +Boot Address: 0xb8000000
 +
 +Board IP address ​                 : 192.168.1.1:​ffffff00  ​
 +Host IP address ​                  : 192.168.1.100  ​
 +Gateway IP address ​               :   
 +Run from flash/host (f/h)         : f  ​
 +Default host run file name        : vmlinux  ​
 +Default host flash file name      : bcm963xx_fs_kernel  ​
 +Boot delay (0-9 seconds) ​         : 1  ​
 +Boot image (0=latest, 1=previous) : 0  ​
 +Board Id (0-3)                    : 96328avng  ​
 +Number of MAC Addresses (1-32) ​   : 6  ​
 +Base MAC Address ​                 : 00:​7f:​28:​8f:​23:​a0  ​
 +PSI Size (1-64) KBytes ​           : 64  ​
 +Enable Backup PSI [0|1]           : 1  ​
 +System Log Size (0-256) KBytes ​   : 0  ​
 +Main Thread Number [0|1]          : 0  ​
 +SSID                              : SBN9H  ​
 +Board Serial Number ​              : CREA2422508781  ​
 +Factory FW Version ​               : GT784WN-VZ-1.1.6  ​
 +WPS PIN                           : 93914130  ​
 +WPA KEY                           : JW2HJXBJ844477P3  ​
 +Voice Board Configuration (0-11) ​ : SI3226  ​
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 0
 +Booting from latest image (0xb8800000) ...
 +Code Address: 0x80010000, Entry Address: 0x80014230
 +Decompression OK!
 +Entry at 0x80014230
 +Closing network.
 +Disabling Switch ports.
 +Flushing Receive Buffers...
 +0 buffers found.
 +Closing DMA Channels.
 +Starting program at 0x80014230
 +Linux version 2.6.30 (bobby@liu) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Wed Feb 8 16:28:22 CST 22
 +HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
 +96328avng prom init
 +CPU revision is: 0002a075 (Broadcom4350)
 +Determined physical RAM map:
 + ​memory:​ 03f00000 @ 00000000 (usable)
 +Zone PFN ranges:
 +  DMA      0x00000000 -> 0x00001000
 +  Normal ​  ​0x00001000 -> 0x00003f00
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0: 0x00000000 -> 0x00003f00
 +On node 0 totalpages: 16128
 +free_area_init_node:​ node 0, pgdat 8031c530, node_mem_map 81000000
 +  DMA zone: 32 pages used for memmap
 +  DMA zone: 0 pages reserved
 +  DMA zone: 4064 pages, LIFO batch:0
 +  Normal zone: 94 pages used for memmap
 +  Normal zone: 11938 pages, LIFO batch:1
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16002
 +Kernel command line: root=31:0 ro noinitrd console=ttyS0,​115200
 +wait instruction:​ enabled
 +Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +RCU-based detection of stalled CPUs is enabled.
 +NR_IRQS:128
 +PID hash table entries: 256 (order: 8, 1024 bytes)
 +console [ttyS0] enabled
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Memory: 60388k/​64512k available (2594k kernel code, 4104k reserved, 530k data, 124k init, 0k highmem)
 +Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
 +Mount-cache hash table entries: 512
 +net_namespace:​ 816 bytes
 +NET: Registered protocol family 16
 +Total Flash size: 16384K with 256 sectors
 +registering PCI controller with io_map_base unset
 +registering PCI controller with io_map_base unset
 +bio: create slab <​bio-0>​ at 0
 +SCSI subsystem initialized
 +usbcore: registered new interface driver usbfs
 +usbcore: registered new interface driver hub
 +usbcore: registered new device driver usb
 +pci 0000:​00:​09.0:​ reg 10 32bit mmio: [0x10002600-0x100026ff]
 +pci 0000:​00:​0a.0:​ reg 10 32bit mmio: [0x10002500-0x100025ff]
 +pci 0000:​01:​00.0:​ PME# supported from D0 D3hot
 +pci 0000:​01:​00.0:​ PME# disabled
 +pci 0000:​02:​00.0:​ reg 10 64bit mmio: [0x000000-0x003fff]
 +pci 0000:​02:​00.0:​ supports D1 D2
 +pci 0000:​01:​00.0:​ PCI bridge, secondary bus 0000:02
 +pci 0000:​01:​00.0: ​  IO window: disabled
 +pci 0000:​01:​00.0: ​  MEM window: 0x10f00000-0x10ffffff
 +pci 0000:​01:​00.0: ​  ​PREFETCH window: disabled
 +PCI: Enabling device 0000:​01:​00.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​01:​00.0 to 64
 +BLOG v3.0 Initialized
 +NET: Registered protocol family 8
 +NET: Registered protocol family 20
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP: Hash tables configured (established 2048 bind 2048)
 +TCP reno registered
 +NET: Registered protocol family 1
 +squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +squashfs: version 4.0 with LZMA457 ported by BRCM
 +fuse init (API version 7.11)
 +msgmni has been set to 117
 +io scheduler noop registered (default)
 +pcieport-driver 0000:​01:​00.0:​ device [14e4:6328] has invalid IRQ; check vendor BIOS
 +PCI: Setting latency timer of device 0000:​01:​00.0 to 64
 +Driver '​sd'​ needs updating - please use bus_type methods
 +PPP generic driver version 2.4.2
 +PPP Deflate Compression module registered
 +PPP BSD Compression module registered
 +NET: Registered protocol family 24
 +bcm963xx_mtd driver v1.0
 +File system address: 0xb8800100
 +ehci_hcd: USB 2.0 '​Enhanced'​ Host Controller (EHCI) Driver
 +PCI: Enabling device 0000:​00:​0a.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​00:​0a.0 to 64
 +ehci_hcd 0000:​00:​0a.0:​ EHCI Host Controller
 +ehci_hcd 0000:​00:​0a.0:​ new USB bus registered, assigned bus number 1
 +ehci_hcd 0000:​00:​0a.0:​ Enabling legacy PCI PM
 +ehci_hcd 0000:​00:​0a.0:​ irq 50, io mem 0x10002500
 +ehci_hcd 0000:​00:​0a.0:​ USB f.f started, EHCI 1.00
 +usb usb1: configuration #1 chosen from 1 choice
 +hub 1-0:1.0: USB hub found
 +hub 1-0:1.0: 1 port detected
 +ohci_hcd: USB 1.1 '​Open'​ Host Controller (OHCI) Driver
 +PCI: Enabling device 0000:​00:​09.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​00:​09.0 to 64
 +ohci_hcd 0000:​00:​09.0:​ OHCI Host Controller
 +ohci_hcd 0000:​00:​09.0:​ new USB bus registered, assigned bus number 2
 +ohci_hcd 0000:​00:​09.0:​ irq 49, io mem 0x10002600
 +usb usb2: configuration #1 chosen from 1 choice
 +hub 2-0:1.0: USB hub found
 +hub 2-0:1.0: 1 port detected
 +usbcore: registered new interface driver usblp
 +Initializing USB Mass Storage driver...
 +usbcore: registered new interface driver usb-storage
 +USB Mass Storage support registered.
 +brcmboard: brcm_board_init entry
 +SES: Button Interrupt 0x1 is enabled
 +SES: LED GPIO 0x1d is enabled
 +SES: LED GPIO 0x1f is enabled
 +Serial: BCM63XX driver $Revision: 1.1.1.1 $
 +ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
 +ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
 +bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Feb  8 2012 16:25:20
 +Broadcom Logger v0.1 Feb  8 2012 16:23:17
 +Mirror/​redirect action on
 +u32 classifier
 +    input device check on 
 +    Actions configured ​
 +TCP cubic registered
 +Initializing XFRM netlink socket
 +NET: Registered protocol family 17
 +NET: Registered protocol family 15
 +Initializing MCPD Module
 +Ebtables v2.0 registered
 +ebt_time registered
 +ebt_ftos registered
 +ebt_wmm_mark registered
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​
 +All bugs added by David S. Miller <​davem@redhat.com>​
 +VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
 +Freeing unused kernel memory: 124k freed
 +init started: ​ BusyBox v1.00 (2012.02.08-08:​31+0000) multi-call binary
 +
 +
 +BusyBox v1.00 (2012.02.08-08:​31+0000) Built-in shell (msh)
 +Enter '​help'​ for a list of built-in commands.
 +
 +
 +Loading drivers and kernel modules... ​
 +
 +pktflow: module license '​Proprietary'​ taints kernel.
 +Disabling lock debugging due to kernel taint
 +Initialized fcache state
 +Broadcom Packet Flow Cache  Char Driver v2.2 Sep 24 2010 18:42:19 Registered<​242>​
 +Created Proc FS /​procfs/​fcache
 +Broadcom Packet Flow Cache registered with netdev chain
 +Broadcom Packet Flow Cache learning via BLOG enabled.
 +Constructed Broadcom Packet Flow Cache v2.2 Sep 24 2010 18:42:19
 +bcmxtmcfg: bcmxtmcfg_init entry
 +adsl: adsl_init entry
 +Broadcom BCM6328B0 Ethernet Network Device v0.1 Feb  8 2012 16:23:27
 +ETH Init: 180 tx BDs at 0xa3962000
 +ETH Init: 400 rx BDs at 0xa39ea000
 +ETH Init: 400 rx BDs at 0xa39e9000
 +dgasp: kerSysRegisterDyingGaspHandler:​ bcmsw registered ​
 +eth0: MAC Address: 00:​7F:​28:​8F:​23:​A0
 +eth1: MAC Address: 00:​7F:​28:​8F:​23:​A0
 +eth2: MAC Address: 00:​7F:​28:​8F:​23:​A0
 +eth3: MAC Address: 00:​7F:​28:​8F:​23:​A0
 +BCM63XX_USB USB Device not present
 +insmod: cannot insert `/​lib/​modules/​2.6.30/​extra/​bcm_usb.ko':​ Success (19): Success
 +PCI: Enabling device 0000:​02:​00.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​02:​00.0 to 64
 +--chipid=13a1a8d9
 +wl:srom strapped
 +wl:(srom strapped) probe/​present=0
 +wl:srom not detected,​using main memory mapped srom info(wombo board)
 +wl:loading /​etc/​wlan/​bcm43225_map.bin
 +wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.11.cpe1.0L0.8
 +dgasp: kerSysRegisterDyingGaspHandler:​ wl0 registered ​
 +p8021ag: p8021ag_init entry
 +Broadcom 802.1Q VLAN Interface, v0.1
 +
 +===== Release Version GT784WN-VZ-1.1.6 (build timestamp 120214_1450) =====
 +
 +rut_getTimeZoneName index:5
 +sntp:​error:​8.830:​main:​606:​servers[0]=ntp.actiontec.com
 +sntp:​error:​8.830:​main:​606:​servers[1]=clock.isc.org
 +sntp:​error:​8.830:​main:​606:​servers[2]=ntp0.nl.net
 +sntp:​error:​8.830:​main:​618:​Try ntp server=ntp.actiontec.com,​line=618
 +ssk:​error:​8.901:​rutMulti_reLoadMcpd:​279:​kill mcpd if exist
 +br0: starting userspace STP failed, starting kernel STP
 +device eth0 entered promiscuous mode
 +ip_tables: (C) 2000-2006 Netfilter Core Team
 +device eth1 entered promiscuous mode
 +device eth2 entered promiscuous mode
 +device eth3 entered promiscuous mode
 +device wl0 entered promiscuous mode
 +br0: topology change detected, propagating
 +br0: port 5(wl0) entering forwarding state
 +WLmngr Daemon is running
 +optarg=0 shmId=0 ​
 +wlevt_init@107:​ opened loopback socket 5
 +wlevt is ready for new msg...
 +ssk:​error:​14.171:​rutMulti_reLoadMcpd:​279:​kill mcpd if exist
 +ssk:​error:​14.256:​rutMulti_reLoadMcpd:​279:​kill mcpd if exist
 +ssk:​error:​14.342:​rutMulti_reLoadMcpd:​279:​kill mcpd if exist
 +BcmAdsl_Initialize=0xC00EE228,​ g_pFnNotifyCallback=0xC0116B44
 +pSdramPHY=0xA3FFFFF8,​ 0x9467B17 0xB7A26E59
 +*** XfaceOffset:​ 0x21F90 => 0x21F90 ***
 +*** PhySdramSize got adjusted: 0x8339C => 0x98D48 ***
 +AdslCoreSharedMemInit:​ shareMemAvailable=422544
 +AdslCoreHwReset: ​ pLocSbSta=83248000 bkupThreshold=1600
 +AdslCoreHwReset: ​ AdslOemDataAddr = 0xA3F783D4
 +dgasp: kerSysRegisterDyingGaspHandler:​ dsl0 registered ​
 +XTM Init: 400 rx BDs at 0xa3210000
 +XTM Init: 100 rx BDs at 0xa3319400
 +iptables: Bad rule (does a matching rule exist in that chain?)
 +iptables: Bad rule (does a matching rule exist in that chain?)
 +ssk:​error:​15.175:​rutMulti_reLoadMcpd:​279:​kill mcpd if exist
 +monitor task is initialized pid= 245 
 +Switch MDK: num_switches = 1
 +Switch MDK: unit = 0; phy_pbmp = 0xf; config_pbmp = 0xf 
 +Switch MDK link poll thread: unit=0; phypbmp=0xf
 +Scratch pad is not initialized.
 +Scratch pad is not initialized.
 +Scratch pad is not initialized.
 +Scratch pad is not initialized.
 +No scratch pad found. ​ Initialize scratch pad...
 +eth3 Link UP 100 mbps full duplex
 +br0: topology change detected, propagating
 +br0: port 4(eth3) entering forwarding state
 +httpd:​error:​17.396:​readMessageFromSmd:​1819:​unrecognized msg 0x10000250
 +WLMNGR-DAEMON:​error:​17.600:​readCfePIN:​3214:​readCfePIN@3214 Read Default PIN = 93914130
 +
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +device wl0 entered promiscuous mode
 +br0: topology change detected, propagating
 +br0: port 5(wl0) entering forwarding state
 +dnsproxy:​error:​18.799:​processCmsMsg:​584:​Disable web activity log,so truncate log file
 +BOARD_IOCTL_SET_SES_LED sesLed_ctrl action=0x0
 +wl0.1 (): not using net_device_ops yet
 +wl0.2 (): not using net_device_ops yet
 +wl0.3 (): not using net_device_ops yet
 +br0: port 5(wl0) entering disabled state
 +WPS Device PIN = 93914130
 +Setting SSID: "​MSLN"​
 +Setting SSID: "​SBN9H1"​
 +Setting SSID: "​SBN9H2"​
 +Setting SSID: "​SBN9H3"​
 +chanspec 0x2b0b selected ​
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +device wl0 entered promiscuous mode
 +br0: topology change detected, propagating
 +br0: port 5(wl0) entering forwarding state
 +ifconfig: br1: error fetching interface information:​ Device not found
 +
 +ifconfig: br2: error fetching interface information:​ Device not found
 +
 +ifconfig: br3: error fetching interface information:​ Device not found
 +
 +Reaped 875
 +UPnP daemon is ready to run
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +device wl0 entered promiscuous mode
 +br0: topology change detected, propagating
 +br0: port 5(wl0) entering forwarding state
 +BOARD_IOCTL_SET_SES_LED sesLed_ctrl action=0x0
 +br0: port 5(wl0) entering disabled state
 +wlctl: Unsupported
 +wlctl: Unsupported
 +wlctl: Unsupported
 +wlctl: Undefined error
 +Setting SSID: "​MSLN"​
 +Setting SSID: "​SBN9H1"​
 +Setting SSID: "​SBN9H2"​
 +Setting SSID: "​SBN9H3"​
 +chanspec 0x2b0b selected ​
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +device wl0 entered promiscuous mode
 +br0: topology change detected, propagating
 +br0: port 5(wl0) entering forwarding state
 +ifconfig: br1: error fetching interface information:​ Device not found
 +
 +ifconfig: br2: error fetching interface information:​ Device not found
 +
 +ifconfig: br3: error fetching interface information:​ Device not found
 +
 +Reaped 1119
 +UPnP daemon is ready to run
 +sntp:​error:​68.898:​sntp:​399:​sntp:​ host not found.
 +sntp:​error:​68.898:​main:​618:​Try ntp server=clock.isc.org,​line=618</​nowiki>​
 +</​WRAP>​\\
 +
 +==== OpenWrt bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​CPUI
 +L1CI
 +DRAM
 +----
 +PHYS
 +ZQDN
 +PHYE
 +DINT
 +LSYN
 +USYN
 +MSYN
 +LMBE
 +PASS
 +----
 +ZBSS
 +CODE
 +DATA
 +L12F
 +MAIN
 +
 +
 +CFE version 1.0.37-106.17 for BCM96328 (32bit,​SP,​BE)
 +Build Date: Wed Jun 15 15:48:10 PDT 2011 (root@localhost.localdomain)
 +Copyright (C) 2000-2009 Broadcom Corporation.
 +
 +HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
 +Total Flash size: 16384K with 256 sectors
 +Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 67108864 bytes (64MB)
 +Boot Address: 0xb8000000
 +
 +Board IP address ​                 : 192.168.1.1:​ffffff00  ​
 +Host IP address ​                  : 192.168.1.100  ​
 +Gateway IP address ​               :   
 +Run from flash/host (f/h)         : f  ​
 +Default host run file name        : vmlinux  ​
 +Default host flash file name      : bcm963xx_fs_kernel  ​
 +Boot delay (0-9 seconds) ​         : 1  ​
 +Board Id (0-3)                    : 96328avng  ​
 +Number of MAC Addresses (1-32) ​   : 6  ​
 +Base MAC Address ​                 : 00:​7f:​28:​8f:​23:​a0  ​
 +PSI Size (1-64) KBytes ​           : 64  ​
 +Enable Backup PSI [0|1]           : 1  ​
 +System Log Size (0-256) KBytes ​   : 0  ​
 +Main Thread Number [0|1]          : 0  ​
 +SSID                              : SBN9H  ​
 +Board Serial Number ​              : CREA2422508781  ​
 +Factory FW Version ​               : GT784WN-VZ-1.1.6  ​
 +WPS PIN                           : 93914130  ​
 +WPA KEY                           : JW2HJXBJ844477P3  ​
 +Voice Board Configuration (0-11) ​ : SI3226  ​
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 0
 +Booting from only image (0xb8010000) ...
 +Code Address: 0x80010000, Entry Address: 0x80010000
 +LZMA: Prossible old LZMA format, trying to decompress..
 +Decompression OK!
 +Entry at 0x80010000
 +Closing network.
 +Disabling Switch ports.
 +Flushing Receive Buffers...
 +0 buffers found.
 +Closing DMA Channels.
 +Starting program at 0x80010000
 +[    0.000000] Linux version 3.7.10 (openwrt@callisto.lab.bufferbloat.net) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 43
 +[    0.000000] Detected Broadcom 0x6328 CPU revision 10b0
 +[    0.000000] CPU frequency is 320 MHz
 +[    0.000000] 64MB of RAM installed
 +[    0.000000] registering 32 GPIOs
 +[    0.000000] board_bcm963xx:​ Boot address 0xb8000000
 +[    0.000000] board_bcm963xx:​ CFE version: 1.0.37-106.17
 +[    0.000000] bcm63xx_nvram:​ nvram checksum invalid (expected 193a0e2c, actual ee8cea72)
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
 +[    0.000000] board_bcm963xx:​ board name: 96328avng
 +[    0.000000] Determined physical RAM map:
 +[    0.000000] ​ memory: 04000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone ranges:
 +[    0.000000] ​  ​Normal ​  [mem 0x00000000-0x03ffffff]
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000] ​  ​node ​  0: [mem 0x00000000-0x03ffffff]
 +[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
 +[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +[    0.000000] Kernel command line:  root=/​dev/​mtdblock2 rootfstype=squashfs,​jffs2 noinitrd console=ttyS0,​115200
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] __ex_table already sorted, skipping sort
 +[    0.000000] Memory: 61272k/​65536k available (2390k kernel code, 4264k reserved, 683k data, 252k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
 +[    0.036000] pid_max: default: 32768 minimum: 301
 +[    0.040000] Mount-cache hash table entries: 512
 +[    0.044000] NET: Registered protocol family 16
 +[    0.272000] registering PCI controller with io_map_base unset
 +[    0.284000] bio: create slab <​bio-0>​ at 0
 +[    0.288000] PCI host bridge to bus 0000:00
 +[    0.292000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
 +[    0.296000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
 +[    0.300000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
 +[    0.304000] pci 0000:​00:​00.0:​ bridge configuration invalid ([bus 00-00]), reconfiguring
 +[    0.308000] pci 0000:​00:​00.0:​ BAR 8: assigned [mem 0x10f00000-0x10ffffff]
 +[    0.312000] pci 0000:​01:​00.0:​ BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
 +[    0.316000] pci 0000:​00:​00.0:​ PCI bridge to [bus 01]
 +[    0.320000] pci 0000:​00:​00.0: ​  ​bridge window [mem 0x10f00000-0x10ffffff]
 +[    0.324000] PCI: Enabling device 0000:​00:​00.0 (0000 -> 0002)
 +[    0.328000] Switching to clocksource MIPS
 +[    0.336000] NET: Registered protocol family 2
 +[    0.344000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +[    0.352000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.356000] TCP: Hash tables configured (established 2048 bind 2048)
 +[    0.364000] TCP: reno registered
 +[    0.368000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.372000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.380000] NET: Registered protocol family 1
 +[    0.388000] audit: initializing netlink socket (disabled)
 +[    0.392000] type=2000 audit(0.392:​1):​ initialized
 +[    0.400000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +[    0.404000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.416000] msgmni has been set to 119
 +[    0.420000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
 +[    0.428000] io scheduler noop registered
 +[    0.432000] io scheduler deadline registered (default)
 +�[    0.448000] console [ttyS0] enabled, bootconsole disabled= 36) is a bcm63xx_uart
 +[    0.448000] console [ttyS0] enabled, bootconsole disabled
 +[    0.464000] m25p80 spi0.0: found s25sl12801, expected m25p80
 +[    0.472000] m25p80 spi0.0: s25sl12801 (16384 Kbytes)
 +[    0.476000] bcm63xxpart:​ CFE boot tag found with version 6 and board type 96328avng
 +[    0.484000] bcm63xxpart:​ Partition 0 is CFE offset 0 and length 10000
 +[    0.492000] bcm63xxpart:​ Partition 1 is kernel offset 10100 and length 10ff00
 +[    0.500000] bcm63xxpart:​ Partition 2 is rootfs offset 120000 and length ed0000
 +[    0.508000] bcm63xxpart:​ Partition 3 is nvram offset ff0000 and length 10000
 +[    0.512000] bcm63xxpart:​ Partition 4 is linux offset 10000 and length fe0000
 +[    0.520000] bcm63xxpart:​ Spare partition is offset 2a0004 and length d4fffc
 +[    0.528000] 5 bcm63xxpart partitions found on MTD device spi0.0
 +[    0.536000] Creating 5 MTD partitions on "​spi0.0":​
 +[    0.540000] 0x000000000000-0x000000010000 : "​CFE"​
 +[    0.548000] 0x000000010100-0x000000120000 : "​kernel"​
 +[    0.552000] mtd: partition "​kernel"​ must either start or end on erase block boundary or be smaller than an erase block -- forcy
 +[    0.568000] 0x000000120000-0x000000ff0000 : "​rootfs"​
 +[    0.576000] mtd: partition "​rootfs"​ set to be root filesystem
 +[    0.580000] mtd: partition "​rootfs_data"​ created automatically,​ ofs=2A0000, len=D50000 ​
 +[    0.592000] 0x0000002a0000-0x000000ff0000 : "​rootfs_data"​
 +[    0.600000] 0x000000ff0000-0x000001000000 : "​nvram"​
 +[    0.608000] 0x000000010000-0x000000ff0000 : "​linux"​
 +[    0.656000] b53_common: found switch: BCM63xx, rev 0
 +[    0.664000] bcm63xx-wdt bcm63xx-wdt: ​ started, timer margin: 30 sec
 +[    0.676000] TCP: cubic registered
 +[    0.676000] NET: Registered protocol family 17
 +[    0.684000] Bridge firewalling registered
 +[    0.688000] 8021q: 802.1Q VLAN Support v1.8
 +[    0.704000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    0.712000] Freeing unused kernel memory: 252k freed
 +- preinit -
 +Press the [f] key and hit [enter] to enter failsafe mode
 +- regular preinit -
 +[    7.144000] jffs2: notice: (317) jffs2_build_xattr_subsystem:​ complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 o.
 +switching to jffs2
 +- init -
 +
 +Please press Enter to activate this console. [    9.152000] Compat-drivers backport release: compat-drivers-2013-01-21-1
 +[    9.160000] Backport based on wireless-testing.git master-2013-02-22
 +[    9.168000] compat.git: wireless-testing.git
 +[    9.228000] cfg80211: Calling CRDA to update world regulatory domain
 +[    9.232000] cfg80211: World regulatory domain updated:
 +[    9.236000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp)
 +[    9.248000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[    9.256000] cfg80211: ​  ​(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[    9.264000] cfg80211: ​  ​(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[    9.272000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[    9.280000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[    9.804000] PCI: Enabling device 0000:​01:​00.0 (0000 -> 0002)
 +[    9.812000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x0A
 +[    9.820000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
 +[    9.828000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
 +[    9.836000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
 +[    9.884000] bcma: bus0: invalid sprom read from the PCIe card, try to use fallback sprom
 +[    9.892000] bcma: bus0: Using fallback SPROM failed (err -2)
 +[    9.900000] bcma: bus0: No SPROM available
 +[    9.912000] bcma: bus0: Bus registered
 +[   ​10.228000] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
 +[   ​10.236000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6
 +[   ​10.244000] Broadcom 43xx driver loaded [ Features: PNL ]
 +[   ​10.412000] Button Hotplug driver version 0.4.1
 +[   ​10.876000] PPP generic driver version 2.4.2
 +[   ​10.964000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​11.160000] NET: Registered protocol family 24
 +[   ​11.196000] nf_conntrack version 0.5.0 (961 buckets, 3844 max)
 +[   ​16.372000] device eth0.1 entered promiscuous mode
 +[   ​16.376000] device eth0 entered promiscuous mode
 +[   ​16.384000] br-lan: port 1(eth0.1) entered forwarding state
 +[   ​16.388000] br-lan: port 1(eth0.1) entered forwarding state
 +[   ​18.392000] br-lan: port 1(eth0.1) entered forwarding state</​nowiki>​
 +</​WRAP>​\\
 +
 +===== Tags =====
 +[[meta:​tags|How to add tags]]
 +{{tag>​bcm63xx bcm6328 1USB USB2.0 64RAM 16Flash MIPS MIPS32 1button}}