User Tools

Site Tools


toh:adb:p.dg_a4001n1
>>>>> Wiki-merge in process >>>>> wiki.openwrt.org + openwrt.org are going to be merged soon, this wiki therefore being read only. Once pages are transfered to openwrt.org, you can edit them again.

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
toh:adb:p.dg_a4001n1 [2012/11/06 23:32]
toh:adb:p.dg_a4001n1 [2016/02/28 09:26] (current)
tmomas [Tags] Ram + Flash added
Line 1: Line 1:
 +====== ADB P.DG A4001N1 ======
 +Supported since [[https://​dev.openwrt.org/​changeset/​33893|R33893]].
  
 +<WRAP box center 80%> {{:​meta:​icons:​tango:​48px-emblem-question.svg.png }} If you can **confirm** that OpenWrt is running on this device (i.e. you or someone else has **tested** it), please update the data accordingly. -> Click //View/Edit data//
 +/* Special style definitions for the various Tables of Hardware. ​           */
 +{{page>​meta:​infobox:​tohstyles&​noheader&​nofooter&​noeditbtn&​inline&​indent&​link}}
 +---- datatable ----
 +cols    : Model, Versions, Supported Since Rev_url, Supported Since Rel, Supported Current Rel, Device Techdata_pageid
 +align   : l,c,l,c,c,c
 +filter ​ : Model=P.DG A4001N1
 +----</​WRAP>​
 +
 +===== Installation =====
 +==== Flashing ANY Firmware ====
 +You must set your TCP/IP v4 protocol to:
 +  - IP: 192.168.1.2
 +  - Netmask: 255.255.255.0
 +  - Gateway: 192.168.1.1
 +  - DNS: (optional, can be blank).
 +
 +Option 1: Works if flashing from the original firmware from telefonica. Access:
 +  - http://​192.168.1.1/​main.html
 +  - username 1234
 +  - password 1234
 +  - select update firmware and proceed
 +
 +Option 2 (does not always work):
 +  - Power off the router.
 +  - Press reset button near the antenna.
 +  - Keep it pressed while powering up during ~20+ seconds.
 +  - Acces to http://​192.168.1.1 and upload binary file.
 +  - Wait until router reboots.
 +
 +===== Hardware =====
 +==== Info ====
 +| **[[wp>​Instruction set|Architecture]]:​** ​ | [[wp>​MIPS architecture|MIPS]] ​  |
 +| **Vendor:​** ​                              | [[wp>​Broadcom]] ​                |
 +| **[[doc:​techref:​Bootloader]]:​** ​          | [[doc:​techref:​bootloader:​CFE]] ​ |
 +| Bootloader version ​                       | 1.0.37-106.24 ​                  |
 +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​ | Broadcom BCM6328 ​         |
 +| **[[doc:​hardware:​cpu|CPU]]/​Speed** ​       | BMIPS4350 v7.5 / 320 MHz  |
 +| **Board ID:**    | 963281T_TEF ​                      |
 +| **Flash-Chip:​** ​ | MX25L128 ​                         |
 +| Flash size       | 16 MiB                            |
 +| RAM              | 32 MiB                            |
 +| Wireless ​        | BCM43225 (14e4:a8d8) 802.11b/​g/​n ​ |
 +| Wireless power   | ? mW                              |
 +| **Ethernet:​** ​   | Internal BRCM6328 Switch ​         |
 +| USB              | yes    |
 +| Power adapter ​   | ?      |
 +| Power margin ​    | ?      |
 +| Antenna ​         | 2x     |
 +| Antenna gain     | ? dBi  |
 +| **[[doc:​hardware:​port.serial|Serial]]:​** ​ | [[#​Serial|Yes]] ​ |
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​     | [[#​JTAG|?​]] ​     |
 +
 +==== Photos ====
 +=== Router ===
 +{{:​media:​adb:​a4001n1.jpg?​400}}
 +
 +==== JTAG ====
 +-> [[doc:​hardware:​port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +N/A
 +
 +==== Serial ====
 +-> [[doc:​hardware:​port.serial]] general information about the serial port, serial port cable, etc.
 +
 +How to connect to the Serial Port of this specific device:\\
 +{{:​media:​adb:​a4001n1_serial.jpg?​400}}
 +
 +===== GPIO =====
 +==== LEDs ====
 +Read: [[doc:​uci:​system#​leds|System configuration:​ Leds]] to configure the leds
 +^ Pin   ^ Event       ^ Active ​  ^
 +| 4     | power       | Low      |
 +| 8     | stop        | Low      |
 +| 11    | inet        | Low      |
 +| 2     | inet-fail ​  | Low      |
 +| 3     | ppp         | Low      |
 +| 5     | ppp-fail ​   | Low      |
 +| 6     | 3g          | Low      |
 +| 7     | 3g-fail ​    | Low      |
 +| 9     | wlan        | Low      |
 +| 10    | wlan-fail ​  | Low      |
 +| 31    | eth         | Low      |
 +| 20    | eth-fail ​   | Low      |
 +
 +==== Buttons ====
 +-> [[doc:​howto:​hardware.button]] on howto use and configure the hardware button(s).
 +^ Pin   ^ Event   ^ Active ​  ^
 +| 23    | reset   | Low      |
 +| 24    | wlan    | Low      |
 +
 +
 +
 +===== Bootlogs =====
 +==== OEM Bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,​SP,​BE)
 +Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold)
 +Copyright (C) 2000-2009 Broadcom Corporation.
 +
 +HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
 +Total Flash size: 16384K with 4096 sectors
 +Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 33554432 bytes (32MB)
 +Boot Address: 0xb8000000
 +
 +Board IP address ​                 : 192.168.1.1:​ffffff00  ​
 +Host IP address ​                  : 192.168.1.10  ​
 +Gateway IP address ​               :   
 +Run from flash/host (f/h)         : f  ​
 +Default host run file name        : run.bin  ​
 +Default host flash file name      : 2.bin  ​
 +Boot delay (0-9 seconds) ​         : 9  ​
 +Board Id (0-4)                    : 963281T_TEF  ​
 +Number of MAC Addresses (1-32) ​   : 11  ​
 +Base MAC Address ​                 : 11:​22:​33:​44:​55:​66  ​
 +PSI Size (1-64) KBytes ​           : 24  ​
 +Enable Backup PSI [0|1]           : 1  ​
 +System Log Size (0-256) KBytes ​   : 0  ​
 +Main Thread Number [0|1]          : 0  ​
 +Voice Board Configuration (0-11) ​ :   
 +
 +*** Press any key to stop auto run (9 seconds) ***
 +Auto run second count down: 9
 +web info: Waiting for connection on socket 0.
 +web info: Waiting for connection on socket 1.
 +web info: Waiting for connection on socket 2.
 +web info: Waiting for connection on socket 0.
 +web info: Waiting for connection on socket 1.
 +web info: Upload 6818609 bytes, Broadcom image format.
 +web info: Waiting for connection on socket 0.
 +
 +Flashing root file system and kernel at 0xb8800000: .....................................................
 +
 +.
 +*** Image flash done *** !
 +
 +Resetting board...HELO
 +CPUI
 +L1CI
 +DRAM
 +----
 +PHYS
 +ZQDN
 +PHYE
 +DINT
 +LSYN
 +USYN
 +MSYN
 +LMBE
 +PASS
 +----
 +ZBSS
 +CODE
 +DATA
 +L12F
 +MAIN
 +
 +
 +CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,​SP,​BE)
 +Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold)
 +Copyright (C) 2000-2009 Broadcom Corporation.
 +
 +HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
 +Total Flash size: 16384K with 4096 sectors
 +Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 33554432 bytes (32MB)
 +Boot Address: 0xb8000000
 +
 +Board IP address ​                 : 192.168.1.1:​ffffff00  ​
 +Host IP address ​                  : 192.168.1.10  ​
 +Gateway IP address ​               :   
 +Run from flash/host (f/h)         : f  ​
 +Default host run file name        : run.bin  ​
 +Default host flash file name      : 2.bin  ​
 +Boot delay (0-9 seconds) ​         : 9  ​
 +Boot image (0=latest, 1=previous) : 0  ​
 +Board Id (0-4)                    : 963281T_TEF  ​
 +Number of MAC Addresses (1-32) ​   : 11  ​
 +Base MAC Address ​                 : 11:​22:​33:​44:​55:​66  ​
 +PSI Size (1-64) KBytes ​           : 24  ​
 +Enable Backup PSI [0|1]           : 1  ​
 +System Log Size (0-256) KBytes ​   : 0  ​
 +Main Thread Number [0|1]          : 0  ​
 +Voice Board Configuration (0-11) ​ :   
 +
 +*** Press any key to stop auto run (9 seconds) ***
 +Auto run second count down: 0
 +Booting from latest image (0xb8800000) ...
 +Code Address: 0x80010000, Entry Address: 0x80014230
 +Decompression OK!
 +Entry at 0x80014230
 +Closing network.
 +Disabling Switch ports.
 +Flushing Receive Buffers...
 +0 buffers found.
 +Closing DMA Channels.
 +Starting program at 0x80014230
 +Linux version 2.6.30 (zu1costast@thorold) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Thu Apr 21 20:1
 +HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
 +963281T_TEF prom init
 +CPU revision is: 0002a075 (Broadcom4350)
 +Determined physical RAM map:
 + ​memory:​ 01f00000 @ 00000000 (usable)
 +Zone PFN ranges:
 +  DMA      0x00000000 -> 0x00001000
 +  Normal ​  ​0x00001000 -> 0x00001f00
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0: 0x00000000 -> 0x00001f00
 +On node 0 totalpages: 7936
 +free_area_init_node:​ node 0, pgdat 802f3830, node_mem_map 81000000
 +  DMA zone: 32 pages used for memmap
 +  DMA zone: 0 pages reserved
 +  DMA zone: 4064 pages, LIFO batch:0
 +  Normal zone: 30 pages used for memmap
 +  Normal zone: 3810 pages, LIFO batch:0
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 7874
 +Kernel command line: root=31:0 ro noinitrd console=ttyS0,​115200
 +wait instruction:​ enabled
 +Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +RCU-based detection of stalled CPUs is enabled.
 +NR_IRQS:128
 +PID hash table entries: 128 (order: 7, 512 bytes)
 +console [ttyS0] enabled
 +Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
 +Memory: 28088k/​31744k available (2409k kernel code, 3656k reserved, 555k data, 120k init, 0k highmem)
 +Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
 +Mount-cache hash table entries: 512
 +net_namespace:​ 536 bytes
 +NET: Registered protocol family 16
 +Total Flash size: 16384K with 4096 sectors
 +registering PCI controller with io_map_base unset
 +registering PCI controller with io_map_base unset
 +bio: create slab <​bio-0>​ at 0
 +SCSI subsystem initialized
 +usbcore: registered new interface driver usbfs
 +usbcore: registered new interface driver hub
 +usbcore: registered new device driver usb
 +pci 0000:​00:​09.0:​ reg 10 32bit mmio: [0x10002600-0x100026ff]
 +pci 0000:​00:​0a.0:​ reg 10 32bit mmio: [0x10002500-0x100025ff]
 +pci 0000:​01:​00.0:​ PME# supported from D0 D3hot
 +pci 0000:​01:​00.0:​ PME# disabled
 +pci 0000:​02:​00.0:​ reg 10 64bit mmio: [0x000000-0x003fff]
 +pci 0000:​02:​00.0:​ supports D1 D2
 +pci 0000:​01:​00.0:​ PCI bridge, secondary bus 0000:02
 +pci 0000:​01:​00.0: ​  IO window: disabled
 +pci 0000:​01:​00.0: ​  MEM window: 0x10f00000-0x10ffffff
 +pci 0000:​01:​00.0: ​  ​PREFETCH window: disabled
 +PCI: Enabling device 0000:​01:​00.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​01:​00.0 to 64
 +BLOG v2.1 Initialized
 +NET: Registered protocol family 8
 +NET: Registered protocol family 20
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 1024 (order: 1, 8192 bytes)
 +TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP: Hash tables configured (established 1024 bind 1024)
 +TCP reno registered
 +NET: Registered protocol family 1
 +squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +squashfs: version 4.0 with LZMA457 ported by BRCM
 +fuse init (API version 7.11)
 +msgmni has been set to 54
 +io scheduler noop registered (default)
 +pcieport-driver 0000:​01:​00.0:​ device [14e4:6328] has invalid IRQ; check vendor BIOS
 +PCI: Setting latency timer of device 0000:​01:​00.0 to 64
 +Driver '​sd'​ needs updating - please use bus_type methods
 +PPP generic driver version 2.4.2
 +PPP Deflate Compression module registered
 +PPP BSD Compression module registered
 +NET: Registered protocol family 24
 +bcm963xx_mtd driver v1.0
 +File system address: 0xb8800100
 +ehci_hcd: USB 2.0 '​Enhanced'​ Host Controller (EHCI) Driver
 +PCI: Enabling device 0000:​00:​0a.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​00:​0a.0 to 64
 +ehci_hcd 0000:​00:​0a.0:​ EHCI Host Controller
 +ehci_hcd 0000:​00:​0a.0:​ new USB bus registered, assigned bus number 1
 +ehci_hcd 0000:​00:​0a.0:​ Enabling legacy PCI PM
 +ehci_hcd 0000:​00:​0a.0:​ irq 50, io mem 0x10002500
 +ehci_hcd 0000:​00:​0a.0:​ USB f.f started, EHCI 1.00
 +usb usb1: configuration #1 chosen from 1 choice
 +hub 1-0:1.0: USB hub found
 +hub 1-0:1.0: 1 port detected
 +ohci_hcd: USB 1.1 '​Open'​ Host Controller (OHCI) Driver
 +PCI: Enabling device 0000:​00:​09.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​00:​09.0 to 64
 +ohci_hcd 0000:​00:​09.0:​ OHCI Host Controller
 +ohci_hcd 0000:​00:​09.0:​ new USB bus registered, assigned bus number 2
 +ohci_hcd 0000:​00:​09.0:​ irq 49, io mem 0x10002600
 +usb usb2: configuration #1 chosen from 1 choice
 +hub 2-0:1.0: USB hub found
 +hub 2-0:1.0: 1 port detected
 +usbcore: registered new interface driver usblp
 +Initializing USB Mass Storage driver...
 +usbcore: registered new interface driver usb-storage
 +USB Mass Storage support registered.
 +brcmboard: brcm_board_init entry
 +SES: Button Interrupt 0x1 is enabled
 +SES: LED GPIO 0x8009 is enabled
 +initLed: led[0]: Gpio=0xffff8003,​ FailGpio=0xffff8005
 +initLed: led[1]: Gpio=0xffffffff,​ FailGpio=0xffffffff
 +initLed: led[2]: Gpio=0xffffffff,​ FailGpio=0xffffffff
 +initLed: led[3]: Gpio=0xffff800b,​ FailGpio=0xffff8002
 +initLed: led[4]: Gpio=0xffff8009,​ FailGpio=0xffff800a
 +initLed: led[5]: Gpio=0xffffffff,​ FailGpio=0xffffffff
 +initLed: led[6]: Gpio=0xffffffff,​ FailGpio=0xffffffff
 +initLed: led[7]: Gpio=0xffff8006,​ FailGpio=0xffff8007
 +initLed: led[8]: Gpio=0xffffffff,​ FailGpio=0xffffffff
 +initLed: led[9]: Gpio=0xffffffff,​ FailGpio=0xffffffff
 +initLed: led[10]: Gpio=0xffffffff,​ FailGpio=0xffffffff
 +initLed: led[11]: Gpio=0xffffffff,​ FailGpio=0xffffffff
 +initLed: led[12]: Gpio=0xffffffff,​ FailGpio=0xffffffff
 +initLed: led[13]: Gpio=0xffff8004,​ FailGpio=0xffff8008
 +initLed: led[14]: Gpio=0xffff8006,​ FailGpio=0xffff8007
 +initLed: led[15]: Gpio=0xffff801f,​ FailGpio=0xffff8014
 +Serial: BCM63XX driver $Revision: 3.00 $
 +ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
 +ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
 +bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Apr 21 2011 20:07:12
 +Broadcom Logger v0.1 Apr 21 2011 20:04:59
 +Mirror/​redirect action on
 +u32 classifier
 +    input device check on 
 +    Actions configured ​
 +TCP cubic registered
 +NET: Registered protocol family 17
 +Initializing MCPD Module
 +Ebtables v2.0 registered
 +ebt_time registered
 +ebt_ftos registered
 +ebt_wmm_mark registered
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​
 +All bugs added by David S. Miller <​davem@redhat.com>​
 +VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
 +Freeing unused kernel memory: 120k freed
 +init started: ​ BusyBox v1.00 (2011.04.21-18:​13+0000) multi-call binary
 +
 +
 +BusyBox v1.00 (2011.04.21-18:​13+0000) Built-in shell (ash)
 +Enter '​help'​ for a list of built-in commands.
 +
 +
 +Loading drivers and kernel modules... ​
 +
 +bcmxtmcfg: module license '​Proprietary'​ taints kernel.
 +Disabling lock debugging due to kernel taint
 +bcmxtmcfg: bcmxtmcfg_init entry
 +adsl: adsl_init entry
 +Broadcom BCM6328B0 Ethernet Network Device v0.1 Apr 21 2011 20:05:03
 +ETH Init: 180 tx BDs at 0xa194e000
 +ETH Init: 400 rx BDs at 0xa19f8000
 +ETH Init: 400 rx BDs at 0xa19f9000
 +dgasp: kerSysRegisterDyingGaspHandler:​ bcmsw registered ​
 +eth0: MAC Address: 11:​22:​33:​44:​55:​66
 +eth1: MAC Address: 11:​22:​33:​44:​55:​66
 +eth2: MAC Address: 11:​22:​33:​44:​55:​66
 +eth3: MAC Address: 11:​22:​33:​44:​55:​66
 +eth0 Link UP 100 mbps full duplex
 +message received before monitor task is initialized kerSysSendtoMonitorTask ​
 +BCM63XX_USB USB Device not present
 +insmod: cannot insert `/​lib/​modules/​2.6.30/​extra/​bcm_usb.ko':​ Success (19): Success
 +PCI: Enabling device 0000:​02:​00.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​02:​00.0 to 64
 +wl:srom not detected,​using main memory mapped srom info(wombo board)
 +wl:loading /​etc/​wlan/​bcm43225_map.bin
 +wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.1.cpePDG_TEF_SP_4.06L4.2
 +dgasp: kerSysRegisterDyingGaspHandler:​ wl0 registered ​
 +Auto-negotiation enabled.
 +The autonegotiated media type is 100baseTx-FD.
 +Link is up
 +mii register 26 is 0x4000
 +
 +===== Release Version PDG_TEF_SP_4.06L.4 (build timestamp 110421_2011) =====
 +
 +factoryCfg = 0
 +iptables v1.4.0: can't initialize iptables table `nat': iptables who? (do you need to insmod?)
 +Perhaps iptables or your kernel needs to be upgraded.
 +sendto: Network is unreachable
 +ip_tables: (C) 2000-2006 Netfilter Core Team
 +device eth0 entered promiscuous mode
 +br0: port 1(eth0) entering forwarding state
 +device eth1 entered promiscuous mode
 +device eth2 entered promiscuous mode
 +device eth3 entered promiscuous mode
 +device wl0 entered promiscuous mode
 +br0: port 5(wl0) entering forwarding state
 +ssk:​error:​23.000:​BcmAdsl_Initialize=0xC00A50D8,​ g_pFnNotifyCallback=0xC00D5E04
 +rutDsl_CfgProfileInit:​2015:​rutDsl_CfgProfileInit()
 +WLmngr Daemon is running
 +optarg=0 shmId=0 ​
 +wlevt_init@107:​ opened loopback socket 4
 +wlevt is ready for new msg...
 +pSdramPHY=0xA1FFFFF8,​ 0x840002 0x40099
 +AdslCoreSharedMemInit:​ shareMemAvailable=484928
 +AdslCoreHwReset: ​ AdslOemDataAddr = 0xA1F6AEB4
 +dgasp: kerSysRegisterDyingGaspHandler:​ dsl0 registered ​
 +XTM Init: 400 rx BDs at 0xa0bb5000
 +XTM Init: 100 rx BDs at 0xa0b12000
 +Netfilter messages via NETLINK v0.30.
 +nf_conntrack version 0.5.0 (496 buckets, 1984 max)
 +iptables: No chain/​target/​match by that name
 +monitor task is initialized pid= 244 
 +There is no Predefined DevicePin in CFE
 +WPS Device PIN = 29942275
 +backup_psi_number_blk=6 result=24576
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +device wl0 entered promiscuous mode
 +br0: port 5(wl0) entering forwarding state
 +backup_psi_number_blk=6 result=24576
 +Setting SSID: "​ESRO2"​
 +Setting SSID: "​wlwl0.1 (): not using net_device_ops yet
 +0_Guest1"​
 +Setting SSID: "​wlwl0.2 (): not using net_device_ops yet
 +0_Guest2"​
 +Setting SSID: "​wlwl0.3 (): not using net_device_ops yet
 +0_Guest3"​
 +br0: port 5(wl0) entering disabled state
 +wlctl: Unsupported
 +wlctl: Unsupported
 +wlctl: Unsupported
 +wlctl: Undefined error
 +chanspec 0x2b01 selected ​
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +device wl0 entered promiscuous mode
 +br0: port 5(wl0) entering forwarding state
 +Reaped 1381
 +UPnP daemon is ready to run</​nowiki>​
 +</​WRAP>​\\
 +
 +==== Openwrt Bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​[ ​   0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #4 Mon Jun 25 11:34:01 CEST 2012
 +[    0.000000] Detected Broadcom 0x6328 CPU revision 10b0
 +[    0.000000] CPU frequency is 320 MHz
 +[    0.000000] 32MB of RAM installed
 +[    0.000000] registering 32 GPIOs
 +[    0.000000] gpiochip_add:​ registered GPIOs 0 to 31 on device: bcm63xx-gpio
 +[    0.000000] board_bcm963xx:​ Boot address 0xb8000000
 +[    0.000000] board_bcm963xx:​ CFE version: A4001N-V0003
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
 +[    0.000000] board_bcm963xx:​ board name: 963281T_TEF
 +[    0.000000] Determined physical RAM map:
 +[    0.000000] ​ memory: 02000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone PFN ranges:
 +[    0.000000] ​  ​Normal ​  ​0x00000000 -> 0x00002000
 +[    0.000000] Movable zone start PFN for each node
 +[    0.000000] Early memory PFN ranges
 +[    0.000000] ​    0: 0x00000000 -> 0x00002000
 +[    0.000000] On node 0 totalpages: 8192
 +[    0.000000] free_area_init_node:​ node 0, pgdat 802a39f0, node_mem_map 81000000
 +[    0.000000] ​  ​Normal zone: 64 pages used for memmap
 +[    0.000000] ​  ​Normal zone: 0 pages reserved
 +[    0.000000] ​  ​Normal zone: 8128 pages, LIFO batch:0
 +[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
 +[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 +[    0.000000] pcpu-alloc:
 +0
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
 +[    0.000000] Kernel command line:  root=/​dev/​mtdblock2 rootfstype=squashfs,​jffs2 noinitrd console=ttyS0,​115200
 +[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
 +[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] Memory: 29384k/​32768k available (2240k kernel code, 3384k reserved, 400k data, 200k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
 +[    0.036000] pid_max: default: 32768 minimum: 301
 +[    0.040000] Mount-cache hash table entries: 512
 +[    0.048000] NET: Registered protocol family 16
 +[    0.280000] registering PCI controller with io_map_base unset
 +[    0.288000] bio: create slab <​bio-0>​ at 0
 +[    0.292000] PCI host bridge to bus 0000:00
 +[    0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
 +[    0.300000] pci_bus 0000:00: root bus resource [ 0x00000000 flags 0x0]
 +[    0.304000] pci 0000:​00:​00.0:​ [14e4:6328] type 1 class 0x000604
 +[    0.304000] pci 0000:​00:​00.0:​ PME# supported from D0 D3hot
 +[    0.304000] pci 0000:​01:​00.0:​ [14e4:a8d8] type 0 class 0x000280
 +[    0.304000] pci 0000:​01:​00.0:​ reg 10: [mem 0x00000000-0x00003fff 64bit]
 +[    0.304000] pci 0000:​01:​00.0:​ supports D1 D2
 +[    0.304000] pci 0000:​00:​00.0:​ BAR 8: assigned [mem 0x10f00000-0x10ffffff]
 +[    0.308000] pci 0000:​01:​00.0:​ BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
 +[    0.312000] pci 0000:​00:​00.0:​ PCI bridge to [bus 01-01]
 +[    0.316000] pci 0000:​00:​00.0: ​  ​bridge window [mem 0x10f00000-0x10ffffff]
 +[    0.320000] PCI: Enabling device 0000:​00:​00.0 (0000 -> 0002)
 +[    0.324000] Switching to clocksource MIPS
 +[    0.332000] PCI: Enabling device 0000:​01:​00.0 (0000 -> 0002)
 +[    0.340000] bcma: Found chip with id 0xA8D9, rev 0x01 and package 0x0A
 +[    0.344000] bcma: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
 +[    0.352000] bcma: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
 +[    0.360000] bcma: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
 +[    0.444000] bcma: Failed to get SPROM: -71
 +[    0.452000] bcma: Bus registered
 +[    0.456000] NET: Registered protocol family 2
 +[    0.460000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.468000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
 +[    0.476000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.480000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.488000] TCP reno registered
 +[    0.492000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.496000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.504000] NET: Registered protocol family 1
 +[    0.508000] PCI: CLS 0 bytes, default 16
 +[    0.512000] audit: initializing netlink socket (disabled)
 +[    0.516000] type=2000 audit(0.516:​1):​ initialized
 +[    0.524000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +[    0.528000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.540000] msgmni has been set to 57
 +[    0.544000] io scheduler noop registered
 +[    0.548000] io scheduler deadline registered (default)
 +[    0.556000] bcm63xx_uart.0:​ ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
 +[    0.564000] console [ttyS0] enabled, bootconsole disabled
 +[    0.580000] m25p80 spi0.0: found mx25l12805d,​ expected m25p80
 +[    0.588000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
 +[    0.592000] bcm63xxpart:​ CFE boot tag found with version 6 and board type 963281T_TEF
 +[    0.600000] bcm63xxpart:​ Partition 0 is CFE offset 0 and length 10000
 +[    0.608000] bcm63xxpart:​ Partition 1 is kernel offset 10100 and length eff00
 +[    0.616000] bcm63xxpart:​ Partition 2 is rootfs offset 100000 and length ef0000
 +[    0.620000] bcm63xxpart:​ Partition 3 is nvram offset ff0000 and length 10000
 +[    0.628000] bcm63xxpart:​ Partition 4 is linux offset 10000 and length fe0000
 +[    0.636000] bcm63xxpart:​ Spare partition is offset 2e0004 and length d0fffc
 +[    0.644000] 5 bcm63xxpart partitions found on MTD device spi0.0
 +[    0.648000] Creating 5 MTD partitions on "​spi0.0":​
 +[    0.656000] 0x000000000000-0x000000010000 : "​CFE"​
 +[    0.664000] 0x000000010100-0x000000100000 : "​kernel"​
 +[    0.668000] mtd: partition "​kernel"​ must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    0.684000] 0x000000100000-0x000000ff0000 : "​rootfs"​
 +[    0.692000] mtd: partition "​rootfs"​ set to be root filesystem
 +[    0.696000] mtd: partition "​rootfs_data"​ created automatically,​ ofs=2E0000, len=D10000 ​
 +[    0.704000] 0x0000002e0000-0x000000ff0000 : "​rootfs_data"​
 +[    0.712000] 0x000000ff0000-0x000001000000 : "​nvram"​
 +[    0.720000] 0x000000010000-0x000000ff0000 : "​linux"​
 +[    0.764000] bcm63xx-wdt bcm63xx-wdt: ​ started, timer margin: 30 sec
 +[    0.772000] Registered led device: 963281T_TEF:​green:​power
 +[    0.772000] Registered led device: 963281T_TEF:​red:​stop
 +[    0.772000] Registered led device: 963281T_TEF:​green:​inet
 +[    0.772000] Registered led device: 963281T_TEF:​red:​inet-fail
 +[    0.776000] Registered led device: 963281T_TEF:​green:​ppp
 +[    0.776000] Registered led device: 963281T_TEF:​red:​ppp-fail
 +[    0.776000] Registered led device: 963281T_TEF:​green:​3g
 +[    0.776000] Registered led device: 963281T_TEF:​red:​3g-fail
 +[    0.776000] Registered led device: 963281T_TEF:​green:​wlan
 +[    0.776000] Registered led device: 963281T_TEF:​red:​wlan-fail
 +[    0.776000] Registered led device: 963281T_TEF:​green:​eth
 +[    0.780000] Registered led device: 963281T_TEF:​red:​eth-fail
 +[    0.780000] TCP westwood registered
 +[    0.784000] NET: Registered protocol family 17
 +[    0.788000] 8021q: 802.1Q VLAN Support v1.8
 +[    0.800000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    0.808000] Freeing unused kernel memory: 200k freed
 +[    3.396000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link UP on Port 4, 100Mbps, full-duplex
 +[    3.452000] roboswitch: Probing device eth0: 
 +[    3.456000] bcm63xx_enet:​ could not find a used port with phy_id 0, assuming phy is external
 +[    3.464000] No Robo switch in managed mode found, phy_id = 0xffffffff
 +[    3.472000] roboswitch: Probing device eth1: No such device
 +[    3.476000] roboswitch: Probing device eth2: No such device
 +[    3.480000] roboswitch: Probing device eth3: No such device
 +[    9.436000] jffs2_scan_eraseblock():​ End of filesystem marker found at 0x10000
 +[    9.444000] jffs2_build_filesystem():​ unlocking the mtd device... done.
 +[    9.448000] jffs2_build_filesystem():​ erasing all blocks after the end marker... done.
 +[  101.636000] JFFS2 notice: (335) jffs2_build_xattr_subsystem:​ complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
 +[  104.920000] Compat-wireless backport release: compat-wireless-2012-06-14
 +[  104.924000] Backport based on wireless-testing.git master-2012-06-14
 +[  104.932000] compat.git: wireless-testing.git
 +[  104.992000] cfg80211: Calling CRDA to update world regulatory domain
 +[  104.996000] cfg80211: World regulatory domain updated:
 +[  105.004000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp)
 +[  105.012000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[  105.020000] cfg80211: ​  ​(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[  105.028000] cfg80211: ​  ​(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[  105.036000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[  105.044000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[  105.432000] NET: Registered protocol family 10
 +[  105.496000] There is already a switch registered on the device '​eth0'​
 +[  105.504000] roboswitch: Probing device eth1: No such device
 +[  105.508000] roboswitch: Probing device eth2: No such device
 +[  105.516000] roboswitch: Probing device eth3: No such device
 +[  106.152000] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
 +[  106.156000] Broadcom 43xx driver loaded [ Features: PNL ]
 +[  106.192000] Button Hotplug driver version 0.4.1
 +[  106.512000] PPP generic driver version 2.4.2
 +[  106.884000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[  107.088000] ieee80211 phy0: Selected rate control algorithm '​minstrel_ht'​
 +[  107.236000] NET: Registered protocol family 24
 +[  107.272000] nf_conntrack version 0.5.0 (462 buckets, 1848 max)
 +[  107.644000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[  107.932000] input: gpio-keys-polled as /​devices/​platform/​gpio-keys-polled.0/​input/​input0
 +[  112.084000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link UP on Port 4, 100Mbps, full-duplex
 +[  112.092000] device eth0 entered promiscuous mode
 +[  112.100000] br-lan: port 1(eth0) entered forwarding state
 +[  112.104000] br-lan: port 1(eth0) entered forwarding state
 +[  114.108000] br-lan: port 1(eth0) entered forwarding state
 +[  122.920000] eth0: no IPv6 routers present</​nowiki>​
 +</​WRAP>​\\
 +
 +===== Tags =====
 +[[meta:​tags|How to add tags]]
 +{{tag>​bcm63xx bcm6328 16flash 32ram}}