Allnet ALL0256N

The ALL0256N is 2.4GHz 802.11n 1T1R outdoor access-point/bridge system based on the Ralink Rt3050. Support for the board used in the device was added to OpenWrt and the device comes with OpenWrt 12.09 preinstalled.

Supported Versions

Version/Model Launch Date OpenWrt Version Supported
- 2012-01 12.09
8M 2012-12 12.09

Hardware Highlights

CPU Ram Flash Network USB Serial JTag
MediaTek Ralink Rt3050F 32MiB 4MiB
8MiB
1 No Yes No

Installation

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24

Switch Ports (for VLANs)

The device got only one Ethernet port. The built-in embedded switch can be used to perform hardware VLAN.

Failsafe mode

Buttons

hardware.button on howto use and configure the hardware button(s).

The ALL0256N got a Reset button. Hold it for more than 10 seconds to restore the factory defaults or use it to trigger Failsafe mode.

Hardware

Info

Architecture: MIPS
Vendor: Ralink
Bootloader: U-Boot
System-On-Chip: Rt3050F (MIPS 24KEc)
CPU/Speed 24KEc V4.12 320 Mhz
Flash size: 4096 KiB
8192 KiB
RAM: 32 MiB
Wireless: built-in
Ethernet: built-in w/ vlan support swconfig
USB: No
Serial: Yes
JTAG: No

Bootlog

[ 0.000000] Linux version 3.7.6 (daniel@earthship) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Thu Feb 7 23:04:36 IST 2013 [ 0.000000] prom: fw_arg0=00000001, fw_arg1=81f52fb0, fw_arg2=01f533b0, fw_arg3=00000000 [ 0.000000] env[0]: memsize=32 [ 0.000000] env[1]: initrd_start=0x00000000 [ 0.000000] env[2]: initrd_size=0x0 [ 0.000000] env[3]: flash_start=0x00000000 [ 0.000000] env[4]: flash_size=0x400000 [ 0.000000] env[0]: memsize=32 [ 0.000000] env[1]: initrd_start=0x00000000 [ 0.000000] env[2]: initrd_size=0x0 [ 0.000000] env[3]: flash_start=0x00000000 [ 0.000000] env[4]: flash_size=0x400000 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001964c (MIPS 24KEc) [ 0.000000] Ralink RT3350 id:1 rev:2 running at 320.00 MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x01ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x01ffffff] [ 0.000000] On node 0 totalpages: 8192 [ 0.000000] free_area_init_node: node 0, pgdat 80247e20, node_mem_map 81000000 [ 0.000000] Normal zone: 64 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 8128 pages, LIFO batch:0 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: board=ALL0256N console=ttyS1,57600 mtdparts=spi0.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),2880k(rootfs),3776k@0x50000(firmware) rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Writing ErrCtl register=0003e270 [ 0.000000] Readback ErrCtl register=0003e270 [ 0.000000] Memory: 29632k/32768k available (2054k kernel code, 3136k reserved, 336k data, 232k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:48 [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.010000] Calibrating delay loop... 212.58 BogoMIPS (lpj=1062912) [ 0.090000] pid_max: default: 32768 minimum: 301 [ 0.090000] Mount-cache hash table entries: 512 [ 0.100000] NET: Registered protocol family 16 [ 0.110000] MIPS: machine is Allnet ALL0256N [ 0.140000] bio: create slab at 0 [ 0.150000] Switching to clocksource MIPS [ 0.160000] NET: Registered protocol family 2 [ 0.170000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.190000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.200000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.210000] TCP: reno registered [ 0.220000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.230000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.250000] NET: Registered protocol family 1 [ 0.300000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.310000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.330000] msgmni has been set to 57 [ 0.340000] io scheduler noop registered [ 0.350000] io scheduler deadline registered (default) [ 0.360000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.370000] serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A [ 0.390000] serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A [ 0.410000] ramips-spi ramips-spi.0: master is unqueued, this is deprecated [ 0.420000] m25p80 spi0.0: mx25l3205d (4096 Kbytes) [ 0.430000] 6 cmdlinepart partitions found on MTD device spi0.0 [ 0.450000] Creating 6 MTD partitions on "spi0.0": [ 0.460000] 0x000000000000-0x000000030000 : "u-boot" [ 0.470000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.490000] 0x000000040000-0x000000050000 : "factory" [ 0.500000] 0x000000050000-0x000000130000 : "kernel" [ 0.510000] 0x000000130000-0x000000400000 : "rootfs" [ 0.530000] mtd: partition "rootfs" set to be root filesystem [ 0.540000] mtd: partition "rootfs_data" created automatically, ofs=390000, len=70000 [ 0.560000] 0x000000390000-0x000000400000 : "rootfs_data" [ 0.570000] 0x000000050000-0x000000400000 : "firmware" [ 0.600000] ramips-wdt ramips-wdt: timeout value must be 0 < timeout <= 40, using 40 [ 0.610000] TCP: cubic registered [ 0.620000] NET: Registered protocol family 17 [ 0.630000] Bridge firewalling registered [ 0.640000] 8021q: 802.1Q VLAN Support v1.8 [ 0.680000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.690000] Freeing unused kernel memory: 232k freed [ 4.980000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0 [ 5.320000] Button Hotplug driver version 0.4.1 [ 6.230000] Registered led device: all0256n:green:rssilow [ 6.230000] Registered led device: all0256n:green:rssimed [ 6.230000] Registered led device: all0256n:green:rssihigh [ 9.870000] jffs2: notice: (358) jffs2_build_xattr_subsystem: complete building xattr subsystem, 67 of xdatum (1 unchecked, 66 orphan) and 81 of xref (0 dead, 66 orphan) found. [ 13.940000] Compat-drivers backport release: compat-drivers-2013-01-08-3 [ 13.950000] Backport based on wireless-testing.git master-2013-01-07 [ 13.970000] compat.git: wireless-testing.git [ 14.030000] cfg80211: Calling CRDA to update world regulatory domain [ 14.040000] cfg80211: World regulatory domain updated: [ 14.050000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 14.070000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 14.080000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 14.100000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 14.110000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 14.130000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 14.850000] NET: Registered protocol family 10 [ 15.660000] zsmalloc: module is from the staging directory, the quality is unknown, you have been warned. [ 15.700000] zram: module is from the staging directory, the quality is unknown, you have been warned. [ 15.720000] zram: num_devices not specified. Using default: 1 [ 15.730000] zram: Creating 1 devices ... [ 16.660000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 16.660000] Registered led device: rt2800pci-phy0::radio [ 16.660000] Registered led device: rt2800pci-phy0::assoc [ 16.660000] Registered led device: rt2800pci-phy0::quality [ 16.760000] PPP generic driver version 2.4.2 [ 16.830000] tun: Universal TUN/TAP device driver, 1.6 [ 16.840000] tun: (C) 1999-2004 Max Krasnyansky [ 17.080000] IPv4 over IPv4 tunneling driver [ 17.120000] l2tp_core: L2TP core driver, V2.0 [ 17.160000] l2tp_netlink: L2TP netlink interface [ 17.200000] sit: IPv6 over IPv4 tunneling driver [ 17.230000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 17.270000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 17.400000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 17.680000] NET: Registered protocol family 24 [ 17.860000] nf_conntrack version 0.5.0 (466 buckets, 1864 max) [ 18.220000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 18.970000] xt_time: kernel timezone is -0000 [ 19.400000] Netfilter messages via NETLINK v0.30. [ 19.550000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 19.890000] ctnetlink v0.93: registering with nfnetlink. [ 20.050000] watchdog: Software Watchdog: cannot register miscdev on minor=130 (err=-16). [ 20.070000] watchdog: Software Watchdog: a legacy watchdog module is probably present. [ 20.080000] softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0) [ 20.540000] u32 classifier [ 20.540000] Performance counters on [ 20.550000] input device check on [ 20.560000] Actions configured [ 20.840000] Mirror/redirect action on [ 23.750000] Adding 14332k swap on /dev/zram0. Priority:-1 extents:1 across:14332k SS [ 27.050000] ramips-wdt: timeout value 60 must be 0 < timeout <= 40, using 40

Tags

Back to top

toh/allnet/all0256n.txt · Last modified: 2014/03/19 00:32 by danitool