Differences

This shows you the differences between two versions of the page.

toh:alpha:asl26555 [2013/01/17 15:19]
toh:alpha:asl26555 [2014/03/19 20:49] (current)
Line 1: Line 1:
-====== ALPHA Amper ASL-26555 ======+====== ALPHA ASL-26555 ======
ADSL wifi router manufactured by [[http://www.alphanetworks.com/|ALPHA Networks]], distributed by ISPs like [[wp>Movistar|Movistar]] ADSL wifi router manufactured by [[http://www.alphanetworks.com/|ALPHA Networks]], distributed by ISPs like [[wp>Movistar|Movistar]]
 +
 +Supported since [[https://dev.openwrt.org/changeset/36433/|r36433]]
===== Supported Versions ===== ===== Supported Versions =====
-^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^ +^ Model ^ Flash size ^ S/N ^ Supported ^ Notes ^ 
-| v1   |  2006-07  | - | - | - +| Spain   | 16MiB GB1260330 1ALISL02ES2G | yes | without ADSL
-| v1.1 | 2008-12  | - | - | - | +| Chile | 8MiB |  | yes | without ADSL |
-| v2  | 2011-01 | - | - | - | +
-FIXME +
- +
-**NOTE:** Anything not included in model specific notes, or where a short comment couldn't be included on the [[#notes]].+
===== Hardware Highlights ===== ===== Hardware Highlights =====
-^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ +^ SoC ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ 
-| Ralink Rt3052F@384MHz | 32MiB | 16MiB | 4 x 1| Yes | Yes | ? | +| Ralink RT3052F@384MHz | 32MiB | 16MiB | 4 x 1| Yes | Yes | ? |
- +
- +
-==== Keep the articles modular ==== +
-| Please include only model specific information, omit bla,bla and put everything generic into separate articles  | +
-| [[doc/howto/generic.overview]] if you have no time to write certain stuff link to this | +
-| [[doc/howto/basic.config]] should lead the way, do not explain this again  | +
-| DO NOT provide a complete howto here! Instead //groom// the general HowTos.  | +
===== Installation ===== ===== Installation =====
Line 32: Line 22:
==== OEM easy installation ==== ==== OEM easy installation ====
-| FIXME The instructions below are for Broadcom devices and only serve as an example. Don't leave them in place if they do not apply to a particular device! +  - Download the firmware for your device
- +    * Boards with 16MB flash -> [[http://downloads.openwrt.org/snapshots/trunk/ramips/openwrt-ramips-rt305x-asl26555-16M-squashfs-sysupgrade.bin|openwrt-ramips-rt305x-asl26555-16M-squashfs-sysupgrade.bin]] 
-This section deals with how you install OpenWrt from a device freshly openedPlus the steps required such as reset to factory defaults if the device has already been configured +     * Boards with 8MB flash -> [[http://downloads.openwrt.org/snapshots/trunk/ramips/openwrt-ramips-rt305x-asl26555-16M-squashfs-sysupgrade.bin|openwrt-ramips-rt305x-asl26555-8M-squashfs-sysupgrade.bin]] 
- + - Rename the firmware to //**openwrt.bin**// 
-**Note:** Reset router to factory defaults if it has been previously configured. +  - Download this mtd binary (or build it your own) 
-  *Browse to http://192.168.1.1/Upgrade.asp +    * http://www.mediafire.com/download/8q9a75xi9w2t4o3/mtd 
-  *Upload .bin file to router +  - Copy //**openwrt.bin**// and //**mtd**// to a FAT32 formatted USB pendrive 
-  *Wait for it to reboot +  - Plug the USB pendrive to the router 
-  *Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.+  - Enter via telnet to the router and execute <code>cd /var/tmp/storage_dev/usb1_1 
 +./mtd write openwrt.bin firmware</code> 
 +  - Wait until it finish and reboot the router 
 +  - Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.
==== OEM installation using the TFTP method ==== ==== OEM installation using the TFTP method ====
-FIXME 
- 
->  [[doc:howto:generic.flashing.tftp]] ->  [[doc:howto:generic.flashing.tftp]]
-=== Specific values you need === +  * Download the firmware for your device: 
-FIXME+     * Boards with 16MB flash -> [[http://downloads.openwrt.org/snapshots/trunk/ramips/openwrt-ramips-rt305x-asl26555-16M-squashfs-sysupgrade.bin|openwrt-ramips-rt305x-asl26555-16M-squashfs-sysupgrade.bin]] 
 +    * Boards with 8MB flash -> [[http://downloads.openwrt.org/snapshots/trunk/ramips/openwrt-ramips-rt305x-asl26555-16M-squashfs-sysupgrade.bin|openwrt-ramips-rt305x-asl26555-8M-squashfs-sysupgrade.bin]] 
 +  * Connect the [[#serial|serial]] TTL cable to interact with uBoot for loading the firmware via tftp. 
 +  * Start a TFTP server in your PC. Copy the firmware to the server. 
 +  * Rename the firmware to sysupgrade.bin 
 +  * Set the IP at your pc to FIXME, and connect the ethernet cable to the router. 
 +  * Power on the router and immediately press the **2** key at the serial console. Say **yes** for flashing the new firmware. 
 +This is a session of flashing via TFTP: 
 +<HTML> 
 +<p style="padding: 10px;border:1px solid grey;height:350px;font:9px/12px Georgia, Garamond, Serif;overflow:Auto;background-color:#DEE4E7"> 
 +<code>
-| Bootloader tftp server IPv4 address | FILL-IN | +FIXMEEE!! 
-| Bootloader MAC address (special) | FILL-IN | + 
-| Firmware tftp image | [[http://downloads.openwrt.org/FILL-IN/openwrt-FILL-IN-generic-FILL-IN-squashfs-tftp.bin]] (**''NOTE:''** Name must contain //&quot;tftp&quot;//) | +</code> 
-| TFTP Transfer Window | FILL-IN seconds | +</p> 
-| TFTP Window Start | approximately FILL-IN seconds after power on | +</HTML> 
-| TFTP Client Required IP Address | FILL-IN |+ 
 +Known issues: the flash memory is divided into 2 regions. This may cause troubles with openwrt. Fix it from uboot command line (choose option 4): 
 +&lt;code&gt
 +setenv activeregion 1 
 +saveenv 
 +reset 
 +</code>
==== Upgrading OpenWrt ==== ==== Upgrading OpenWrt ====
->  [[doc:howto:generic.sysupgrade]] ->  [[doc:howto:generic.sysupgrade]]
 +
 +
 +FIXME
If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
Line 75: Line 85:
<code> <code>
cd /tmp/ cd /tmp/
-wget http://http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc+wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc sysupgrade /tmp/xxx.abc
</code> </code>
Line 83: Line 93:
<code> <code>
cd /tmp/ cd /tmp/
-wget http://http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc+wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc linux && reboot</code> mtd write /tmp/xxx.abc linux && reboot</code>
Line 897: Line 907:
</p> </p>
</HTML> </HTML>
 +
 +==== TrendChip bootlog (ADSL) ====
 +<HTML>
 +<p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF">
 +<code>Bootbase Version: VTC_SPI_BR1.1 | 2009/5/26 14:28:26
 +RAM: Size = 2048 Kbytes
 +DRAM POST: Testing:    OK  64K  96K  128K  160K  192K  224K  256K  288K  320K  352K  384K  416K  448K  480K  512K  544K  576K  608K  640K  672K  704K  736K  768K  800K  832K  864K  896K  928K  960K  992K 1024K 1056K 1088K 1120K 1152K 1184K 1216K 1248K 1280K 1312K 1344K 1376K 1408K 1440K 1472K 1504K 1536K 1568K 1600K 1632K 1664K 1696K 1728K 1760K 1792K 1824K 1856K 1888K 1920K 1952K 1984K 2016K 2048K
 +OK
 +Found SPI Flash 512KiB W25X40 at 0xbfc00000
 +
 +RAS Version: v2.1                                                             
 +System  ID: #3.6.17.0(BE0.C3)3.12.8.128| 2010/12/28 
 +
 +Press any key to enter debug mode within 3 seconds.
 +............................................................
 +Copyright (c) 2001 - 2006 TrendChip Technologies Corp.
 +initialize ch = 0, ethernet address: 00:aa:bb:01:23:45
 +Wan Channel init ........ done
 +Initializing ADSL F/W ........ done
 +Telefonica SET ADSL2PLUS_FIRST!
 +ANNEXAIJLM
 +US bitswap on,DS bitswap on
 +OlrON
 +SRAOFF
 +Press ENTER to continue...
 +Testlab 23
 +largeD flag=2 (0:maxD=64, 1:maxD=128, 2:maxD=511)
 +model check flag: on.
 +product/customer number: 222/6
 +
 +Password: XXXXX
 +Copyright (c) 2001 - 2006 TrendChip Technologies Corp.
 +tc> sys tpget sys show adsl
 +adslmode=6,adsltype=4,bitswap=0tc> sys tpget wan atm pvc disp
 +index=0,active=1,encap=0,mode=0,vid=0,vpi=0,vci=35,qostype=0,pcr=0,scr=0,mbs=0in
 +dex=1,active=1,encap=0,mode=0,vid=0,vpi=14,vci=24,qostype=0,pcr=0,scr=0,mbs=0ind
 +ex=2,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0ind
 +ex=3,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0ind
 +ex=4,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0ind
 +ex=5,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0ind
 +ex=6,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0ind
 +ex=7,active=0,encap=0,mode=0,vid=4095,vpi=0,vci=0,qostype=0,pcr=0,scr=0,mbs=0COM
 +PLETEtc> sys tpget sys verinfo
 +Bootbase=VTC_SPI_BR1.1 | 2009/5/26,RAS=v2.1,System=#3.6.17.0(BE0.C3)3.12.8.128[D
 +ec 30 2010 14:43:51],FwVer=3.12.8.128_TC3086,HwVer=T14.F7_6.0,Standard=Multi-Mod
 +e,Country Code=255,MAC Address=00:aa:bb:01:23:45tc> sys tpget wan adsl status
 +current modem status: down
 +tc> sys tpget wan adsl status
 +current modem status: down
 +tc> sys tpget wan adsl status
 +current modem status: down
 +tc>
 +</code>
 +</p>
 +</HTML>
 +
===== Basic configuration ===== ===== Basic configuration =====
-> [[doc:howto:basic.config|Basic configuration]] After flashing, proceed with this.\\ -> [[doc:howto:basic.config|Basic configuration]] After flashing, proceed with this.\\
Line 913: Line 979:
==== Switch Ports (for VLANs) ==== ==== Switch Ports (for VLANs) ====
 +FIXME
 +
Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on. Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.
^ Port ^ Switch port ^ ^ Port ^ Switch port ^
Line 935: Line 1003:
===== Hardware ===== ===== Hardware =====
==== Info ==== ==== Info ====
-| **[[wp>Instruction set|Architecture]]:**    | [[wp>MIPS architecture|MIPS]] | +| **[[wp>Instruction set|Architecture]]:**    | [[wp>MIPS architecture|MIPS]] |
-| **Vendor:**          | [[wp>Ralink]] | +| **Vendor:**          | [[wp>Ralink]] |
-| **[[doc:techref:Bootloader]]:**    | [[doc:techref:bootloader:uboot|U-Boot]] | +| **[[doc:techref:Bootloader]]:**    | [[doc:techref:bootloader:uboot|U-Boot]] |
-| **[[doc:hardware:soc|System-On-Chip]]:**  | RaLink Rt3052F +| **[[doc:hardware:soc|System-On-Chip]]:**  | Ralink RT3052F |
-| **[[doc:hardware:cpu|CPU]]/Speed**        | 24Kec V4.12 / 384 Mhz +| **[[doc:hardware:cpu|CPU]]/Speed**        | 24KEc V4.12 / 384 MHz |
-| **Flash-Chip:**      | FIXME +| **Flash-Chip:**      | [[http://www.spansion.com/Support/Datasheets/S25FL128P_00.pdf|Spansion S25FL128P]] \\ [[http://www.spansion.com/Support/Datasheets/S25FL064P_00.pdf|Spansion S25FL064P]] | SPI memory
-| **Flash size:**      | 16 miB +| **Flash size:**      | 16 MiB\\ 8 MiB | Spain version\\ Chile version
-| **RAM:**            | 32 MiB  | +| **RAM:**            | [[http://www.esmt.com.tw/DB/manager/upload/M12L2561616A(2A).pdf|ESMT M12L2561616A-6T]] / SDR-166 || 
-| **Wireless:**        | Ralink 2800 2.4ghz 802.11bgn (onboard) +| **RAM size:**        | 32 MiB  |
-| **Ethernet:**        | FIXME w/ vlan support [[doc:techref:swconfig]] | +| **Wireless:**        | Ralink RT3052 (integrated) 2.4GHz 802.11b/g/n |
-| **Internet:**        | xDSL  +| **Ethernet:**        | Ralink RT3052 (integrated) w/ vlan support [[doc:techref:swconfig]] || 
-| **USB:**            | Yes 1 x 2.0    | +| **ADSL:** | TrendChip SoC connected internally through lan/serial port |
-| **[[doc:hardware:port.serial|Serial]]:**          | [[#Serial|Yes]] | +| **Internet:**        | ADSL2+ |
-| **[[doc:hardware:port.jtag|JTAG]]:**            | [[#JTAG|?]]  |+| **USB:**            | Yes 1 x 2.0    |
 +| **[[doc:hardware:port.serial|Serial]]:**          | [[#Serial|Yes]] |
 +| **[[doc:hardware:port.jtag|JTAG]]:**            | [[#JTAG|?]]  ||
==== Photos ==== ==== Photos ====
Model Number Model Number
-//Front://+{{:toh:adb:a4001n1.jpg}}
**Photo of front of the casing** **Photo of front of the casing**
Line 966: Line 1036:
  *To remove the cover do a/b/c   *To remove the cover do a/b/c
-//Main PCB// +|  Top View  |  Bottom View  | 
 +| {{:toh:alpha:asl26555_top.jpg?400|}} | {{:toh:alpha:asl26555_bottom.jpg?400|}} |
**Photo of PCB** **Photo of PCB**
Line 974: Line 1044:
How to connect to the Serial Port of this specific device: How to connect to the Serial Port of this specific device:
 +
 +{{http://4.bp.blogspot.com/-jGsbLW78cWA/T75uvBO4ttI/AAAAAAAAEYE/86X0Z5Hhmcw/s1600/asl26555_serial.jpg?400}}
**Photo of PCB with markings** **Photo of PCB with markings**
Line 994: Line 1066:
  - as a beginner, you really should inform yourself about [[doc:hardware:soldering]] in general and then obtain some practical experience!   - as a beginner, you really should inform yourself about [[doc:hardware:soldering]] in general and then obtain some practical experience!
-==== 128MiB RAM Mod ====+==== 64MiB RAM Mod ==== 
 + 
 +Solder an extra M12L2561616A-6T or compatible SDR RAM IC. Then solder two additional 402 SMD parts: R42 = 33R y C75 = 5.1 pF 
 + 
 +{{:media:asl26555_64mb_1.jpg|}} 
 + 
 +Desolder R118 and solder to R119 pads: 
 + 
 +{{:media:asl26555_64mb_2.jpg|}} 
==== I²C GPIO Mod ==== ==== I²C GPIO Mod ====
-==== I²C Tiny-USB Mod ==== 
-===== Notes =====+"Internet" LED pins are SDA al SCL; Remove capacitors as depicted and external pull-up resistors: 
 + 
 +{{:media:asl26555_i2c.png|}}
Line 1004: Line 1086:
For some Help with the Tags, please have a look here: [[meta/tags]] For some Help with the Tags, please have a look here: [[meta/tags]]
-{{tag>FastEthernet 5Port USB 32RAM 24K}}+{{tag>ramips rt3052 FastEthernet 5Port USB 32RAM 24K}}

Back to top

toh/alpha/asl26555.1358432356.txt.bz2 · Last modified: 2013/01/17 15:19 (external edit)