User Tools

Site Tools


toh:arcadyan:ar7516

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
toh:arcadyan:ar7516 [2012/11/03 18:50]
toh:arcadyan:ar7516 [2015/08/10 22:32] (current)
zx82 [Serial]
Line 1: Line 1:
 +====== Arcadyan AR7516 ======
 +[[https://​forum.openwrt.org/​viewtopic.php?​id=43883|Forum thread]]
 +
 +===== Status =====
 +
 +Chaos Calmer 15.05-rc3 has been booted on this device; caveats:
 +   * haven'​t worked out a simple way to install a bootloader yet
 +   * WiFi drivers aren't automatically included, but b43-based WiFi appears to work (very quick test)
 +   * LEDs probably need customising to the device
 +   * USB doesn'​t seem to work out of the box
 +   * As with all BCM63XX devices, there is **no** support for the integrated DSL modem. ​
 +
 +The stock CFE on (at least) units branded as "EE BrightBox"​ has some (unexplored) limitations on what images it'll accept. ​ [[doc/​techref/​bootloader/​cfe#​bcm63xx_cfe|CFE]] [[https://​forum.openwrt.org/​viewtopic.php?​pid=275793#​p275793|image]] built for another 6328 device, the [[toh/​thomson/​tg582n|Technicolor TG582n]], is generic enough to work on the AR7516. ​ See below for approaches for getting a replacement CFE flashed.
 +
 +There'​s no dedicated OpenWRT build (yet?) but the [[toh/​d-link/​dsl-2740b|D-Link DSL-274xB]] F1 revision is similar enough that its firmware boots the AR7516. ​ As it's for a different device the wrong WiFi drivers are installed and the LEDs and GPIOs are probably wrong. ​ USB may just need someone to take a look at the bootlog for obvious missing drivers/​config options.
 +
 +===== Intro =====
 +
 The AR7516 is branded in the UK as the Orange Brightbox router. The AR7516 is branded in the UK as the Orange Brightbox router.
  
 This is the [[http://​www.arcadyan.com/​contentPage.aspx?​type=product-detail&​L2id=4&​prod2id=2 | AR7516]] product page This is the [[http://​www.arcadyan.com/​contentPage.aspx?​type=product-detail&​L2id=4&​prod2id=2 | AR7516]] product page
  
-These are the stock firmware'​s hidden [[http://​forums.thinkbroadband.com/​freeserve/​4091269-orange-bright-box-hidden-config-pages-new.html | config]] pages+These are the stock firmware'​s ​(not so) hidden [[http://​forums.thinkbroadband.com/​freeserve/​4091269-orange-bright-box-hidden-config-pages-new.html | config]] pages.
  
-[[http://help.orange.co.uk/orangeuk/support/​personal/​651593 ​Firmware update]] is available via holding ​the reset button for 8+ seconds+The stock Orange firmware is vulnerable to hacks by [[https://scotthelme.co.uk/ee-brightbox-router-hacked/|people given the WiFi password]], at least, and (judging by the quality of the firmware) probably to remote hacks that aren't public yet.
  
-[[http://​www.the-scream.co.uk/​forums/​t31206.html | Telnet]] ​is available over serial ​via popping the lid+[[http://​help.orange.co.uk/​orangeuk/​support/​personal/​651593 | Firmware update]] is available via holding the reset button for 8+ seconds. Also via the Admin menu. 
 + 
 +[[http://​www.the-scream.co.uk/​forums/​t31206.html | Telnet]] ​can be enabled ​via popping the lid and serial connecting, or by entering '​Manufactory Mode' (see below). 
 + 
 +===== Hardware ===== 
 +==== Info ==== 
 +| **[[wp>​Instruction set|Architecture]]:​** ​   | [[wp>​MIPS architecture|MIPS]] | 
 +| **Vendor:​** ​         | [[wp>​Broadcom]] | 
 +| **[[doc:​techref:​Bootloader]]:​** ​    | [[doc:​techref:​bootloader:​CFE]] | 
 +| **Board ID:**      | AR7516AAW ​ | 
 +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​ | Broadcom BCM6328 | 
 +| **[[doc:​hardware:​cpu|CPU]]/​Speed** ​       | BMIPS4350 v7.5 / 320 MHz | 
 +| **Flash-Chip:​** ​     | [[http://​media.digikey.com/​pdf/​Data%20Sheets/​Macronix/​MX25L6406E.pdf|Macronix MX25L6406E]] | 
 +| **Flash size** | 8 MiB | 
 +| **RAM-Chip** | EM68B16CWQD-25H / DDR2-800 | 
 +| **RAM** | 64 MiB | 
 +| **Wireless** | Broadcom BCM43227 (onboard) | 
 +| **Ethernet:​** ​  | BRCM6328 Switch (integrated on SoC) | 
 +| **USB** | Yes | 
 +| **[[doc:​hardware:​port.serial|Serial]]:​** ​ | [[#​Serial|Yes]] | 
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​     | [[#​JTAG|?​]] ​ | 
 + 
 +==== Serial ==== 
 + 
 +J3, between the CPU and the USB port; unpopulated through-holes (some early models may have been left populated?​). ​ 3V3, 115200/​8/​N/​1 in stock stuff and CFEs. 
 + 
 +   * pin 2: TX 
 +   * pin 3: RX 
 +   * pin 4 (unlabelled):​ GND 
 + 
 +{{:​media:​toh:​arcadyan:​ar7516:​serial.jpg?​250 |}} 
 + 
 + 
 +===== '​Manufactory'​ Mode/Telnet ===== 
 + 
 +In later "​BrightBox"​ stock firmware (maybe EE branded and beyond?) it is possible to enable telnet access without opening the device. ​ The process involves accessing a hidden settings page and resetting the box into the manufacturer'​s factory default mode.  Please note: this is not the same page as the "​factory default"​ page accessible from the Advanced Set-Up->​Tools menu. 
 + 
 +The steps are as follows: 
 + 
 +  - Go to your router'​s configuration in your web browser, e.g. http://​192.168.1.1/​ 
 +  - Log in using the user name and password 
 +  - Optionally, but recommended,​ visit Advanced Set-Up->​Tools->​Configuration and backup your current config 
 +  - Now, change the location of the current page in your browser to //​u132xzp32aai.htm//,​ so that the full address is, for example, http://​192.168.1.1/​u132xzp32aai.htm 
 +  - Click the button that says "​Manufactory Default"​ 
 + 
 +Once the router finishes doing its thing, you can now telnet in using the user name **root** and the password **password**. ​ A significant drawback is that your router'​s normal functions may be impaired whilst in this mode.  For instance, you may not be able to alter the wireless settings or use your broadband. 
 + 
 +In "​Orange BrightBox"​ branded versions you must either use the serial port (which provides a root shell by default) or upgrade to a vulnerable "EE BrightBox"​ firmware first. 
 +===== Installation ===== 
 + 
 +//Not user-friendly yet, and written by someone very new to router hacking; probably much room for improvement.//​ 
 + 
 +The stock version of CFE on EE BrightBox branded units offers both bootloader upgrade and main firmware upgrade, but requires at least the main firmware to pass some check that an OpenWRT image fails. ​ The check is probably known, but a more complete CFE is reassuring and not too hard to flash using the existing root access, so that's the only route tried so far. 
 + 
 +Using the "​Manufactory"​ mode root login via telnet or serial console, a generic (enough) 6328 CFE can be flashed by writing to the raw mtdblock partitions. ​ You can get it to the device in preparation for flashing by: 
 + * USB, assuming USB mass storage works in the stock firmware '​manufactory mode'?​ 
 + * network; while there'​s no netcat in the stock firmware/​busybox,​ [[http://​www.wsec.be/​blog/​2009/​07/​20/​using-openssl-as-a-netcat-replacement|openssl can be substituted]]. 
 + * serial; use cat/​dd/​minicom/​cutecom/​gtkterm/​anything else that can send a stream on the sending end, and maybe dd with a count on the receiving end to ensure you get back to the shell; openssl can be used to MD5 the received file and/or to base64-decode if you want to avoid issues escaping control characters. 
 + * SPI (skipping the root shell); flashrom or any other SPI programmer direct to the flash chip would work. 
 + 
 +The generic CFE is slightly too big (~64k) to just overwrite the stock CFE partition and MTD partitions can't be created on the fly, so to get it to fit it needs to be either rebuilt with the fat trimmed off, or it needs to be split into three pieces and each written to an existing MTD partition. ​ cfe6328-tg582n-custom.bin is 64688 bytes. ​ Splitting this into appropriately sized chunks (dd would work) and writing them to mtdblock5 ("​bootldr",​ 57344 bytes), mtdblock0 ("​manuf",​ 4096 bytes) and mtdblock1 ("​nvram",​ 4096 bytes) will achieve a flash. 
 + 
 +The stock MTD partitions (rearranged into flash chip order) are: 
 +<​code>​mtdblock5:​ 0x000000000000-0x00000000e000 : "​bootldr"​ 
 +mtdblock0: 0x00000000e000-0x00000000f000 : "​manuf"​ 
 +mtdblock1: 0x00000000f000-0x000000010000 : "​nvram"​ 
 +mtdblock3: 0x000000010000-0x0000007f0000 : "​priimg"​ 
 +mtdblock2: 0x000000110000-0x0000007f0000 : "​rootfs"​ 
 +mtdblock4: 0x0000007f0000-0x000000800000 : "​pricfg"​ 
 +</​code>​ 
 + 
 +Once the generic 6328 CFE bootloader is flashed, at/after reboot the usual 63xx hold-reset-from-power-on or interrupt-the-boot-over-serial techniques will cause CFE to wait for (OpenWRT) image upload via its built-in web interface.
  
 ===== Bootlogs ===== ===== Bootlogs =====
 ==== OEM Bootlog ==== ==== OEM Bootlog ====
 +
 <​HTML>​ <​HTML>​
-<p style="​padding:​ 10px;​border:​1px solid grey;​height:​300px;​font:​10px/​14px Georgia, Garamond, Serif;​overflow:​Auto;​background-color:#​FFFFFF">​ +<p style="​padding:​ 10px;​border:​1px solid grey;​height:​600px;​font:​10px/​14px Georgia, Garamond, Serif;​overflow:​Auto;​background-color:#​FFFFFF">​ 
-<​code>​ +<​code>​HELO
-HELO+
 CPUI CPUI
 L1CI L1CI
Line 443: Line 532:
  ​System Start with Normal Phase   ​System Start with Normal Phase 
 root@BrightBox:/​ # root@BrightBox:/​ #
 +</​code>​
 +</p>
 +</​HTML>​
 +
 +==== OpenWRT Bootlog ====
 +
 +This is a boot using the TG582n CFE and the D-Link DSL-2740B/​DSL-2741B rev F1 image, but running on the AR7516.
 +<​HTML>​
 +<p style="​padding:​ 10px;​border:​1px solid grey;​height:​600px;​font:​10px/​14px Georgia, Garamond, Serif;​overflow:​Auto;​background-color:#​FFFFFF">​
 +<​code>​
 +HELO
 +CPUI
 +L1CI
 +DRAM
 +----
 +PHYS
 +ZQDN
 +PHYE
 +DINT
 +LSYN
 +USYN
 +MSYN
 +LMBE
 +PASS
 +----
 +ZBSS
 +CODE
 +DATA
 +L12F
 +MAIN
 +
 +
 +CFE version 2.0.3 for DGN2200v2 (32bit,​SP,​BE)
 +Build Date: s\0xc3\0xa1b may  9 21:45:47 CEST 2015 (dani@tool)
 +Copyright (C) 2000-2009 Broadcom Corporation.
 +
 +HS Serial flash device: name MX25L64, id 0xc217 size 8192KB
 +Total Flash size: 8192K with 2048 sectors
 +** HELLO **
 +
 +Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 67108864 bytes (64MB)
 +Boot Address: 0xb8000000
 +
 +Board IP address ​                 : 192.168.1.1:​ffffff00  ​
 +Host IP address ​                  : 192.168.1.100  ​
 +Gateway IP address ​               :   
 +Run from flash/host (f/h)         : f  ​
 +Default host run file name        : vmlinux  ​
 +Default host flash file name      : bcm963xx_fs_kernel  ​
 +Boot delay (0-9 seconds) ​         : 1  ​
 +Board Id (0-4)                    : 963281TAN  ​
 +Number of MAC Addresses (1-32) ​   : 10  ​
 +Base MAC Address ​                 : 00:​00:​00:​00:​00:​01  ​
 +PSI Size (1-64) KBytes ​           : 24  ​
 +Enable Backup PSI [0|1]           : 0  ​
 +System Log Size (0-256) KBytes ​   : 0  ​
 +Main Thread Number [0|1]          : 0  ​
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 1\0x081\0x080
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 1\0x081\0x080
 +Booting from only image (0xb8010000) ...
 +Code Address: 0x80A00000, Entry Address: 0x80a00000
 +LZMA: Prossible old LZMA format, trying to decompress..
 +Decompression OK!
 +Entry at 0x80a00000
 +Closing network.
 +Disabling Switch ports.
 +Flushing Receive Buffers...
 +2 buffers found.
 +Closing DMA Channels.
 +Starting program at 0x80a00000
 +[    0.000000] Linux version 3.18.17 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/​Linaro GCC 4.8-2014.04 r46018) ) #1 Fri Jul 3 16:32:38 CEST 2015
 +[    0.000000] Detected Broadcom 0x6328 CPU revision b0
 +[    0.000000] CPU frequency is 320 MHz
 +[    0.000000] 64MB of RAM installed
 +[    0.000000] board_bcm963xx:​ Boot address 0xb8000000
 +[    0.000000] board_bcm963xx:​ CFE version: 1.0.37-106.24
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU0 revision is: 0002a075 (Broadcom BMIPS4350)
 +[    0.000000] board: board name: AW4339U
 +[    0.000000] MIPS: machine is D-Link DSL-2740B/​DSL-2741B rev F1
 +[    0.000000] Determined physical RAM map:
 +[    0.000000] ​ memory: 04000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone ranges:
 +[    0.000000] ​  ​Normal ​  [mem 0x00000000-0x03ffffff]
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000] ​  ​node ​  0: [mem 0x00000000-0x03ffffff]
 +[    0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff]
 +[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +[    0.000000] Kernel command line:  root=/​dev/​mtdblock2 rootfstype=squashfs,​jffs2 noinitrd console=ttyS0,​115200
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Memory: 59716K/​65536K available (2813K kernel code, 139K rwdata, 664K rodata, 1304K init, 192K bss, 5820K reserved)
 +[    0.000000] NR_IRQS:256
 +[    0.000000] Calibrating delay loop... 319.74 BogoMIPS (lpj=639488)
 +[    0.040000] pid_max: default: 32768 minimum: 301
 +[    0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.060000] NET: Registered protocol family 16
 +[    0.300000] registering PCI controller with io_map_base unset
 +[    0.324000] PCI host bridge to bus 0000:00
 +[    0.328000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x10ffffff]
 +[    0.332000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
 +[    0.336000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
 +[    0.340000] pci 0000:​00:​00.0:​ bridge configuration invalid ([bus 00-00]), reconfiguring
 +[    0.344000] pci 0000:​00:​00.0:​ BAR 8: assigned [mem 0x10f00000-0x10ffffff]
 +[    0.348000] pci 0000:​01:​00.0:​ BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
 +[    0.352000] pci 0000:​00:​00.0:​ PCI bridge to [bus 01]
 +[    0.356000] pci 0000:​00:​00.0: ​  ​bridge window [mem 0x10f00000-0x10ffffff]
 +[    0.360000] Switched to clocksource MIPS
 +[    0.364000] PCI: Enabling device 0000:​00:​00.0 (0000 -> 0002)
 +[    0.372000] PCI: Enabling device 0000:​01:​00.0 (0000 -> 0002)
 +[    0.376000] bcma: bus0: Found chip with id 43227, rev 0x00 and package 0x08
 +[    0.384000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x25, class 0x0)
 +[    0.392000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x1E, class 0x0)
 +[    0.404000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x12, class 0x0)
 +[    0.412000] bcma: bus0: Core 3 found: SDIO Device (manuf 0x4BF, id 0x829, rev 0x07, class 0x0)
 +[    0.420000] bcma: bus0: Using fallback SPROM failed (err -2)
 +[    0.424000] bcma: bus0: No SPROM available
 +[    0.440000] bcma: bus0: Bus registered
 +[    0.444000] NET: Registered protocol family 2
 +[    0.452000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.460000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.464000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.472000] TCP: reno registered
 +[    0.476000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.480000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.488000] NET: Registered protocol family 1
 +[    0.496000] futex hash table entries: 256 (order: -1, 3072 bytes)
 +[    0.508000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +[    0.512000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.524000] msgmni has been set to 116
 +[    0.528000] io scheduler noop registered
 +[    0.532000] io scheduler deadline registered (default)
 +[    0.540000] bcm63xx_uart.0:​ ttyS0 at MMIO 0xb0000100 (irq = 36, base_baud = 1562500) is a bcm63xx_uart
 +[    0.552000] console [ttyS0] enabled
 +[    0.552000] console [ttyS0] enabled
 +[    0.556000] bootconsole [early0] disabled
 +[    0.556000] bootconsole [early0] disabled
 +[    0.568000] m25p80 spi1.0: found mx25l6405d, expected m25p80
 +[    0.576000] m25p80 spi1.0: mx25l6405d (8192 Kbytes)
 +[    0.580000] bcm63xxpart:​ CFE boot tag found with version 6 and board type AW4339U
 +[    0.588000] bcm63xxpart:​ Partition 0 is CFE offset 0 and length 10000
 +[    0.596000] bcm63xxpart:​ Partition 1 is kernel offset 10100 and length 136008
 +[    0.604000] bcm63xxpart:​ Partition 2 is rootfs offset 146108 and length 689ef8
 +[    0.612000] bcm63xxpart:​ Partition 3 is cal_data offset 7d0000 and length 10000
 +[    0.616000] bcm63xxpart:​ Partition 4 is nvram offset 7f0000 and length 10000
 +[    0.624000] bcm63xxpart:​ Partition 5 is linux offset 10000 and length 7c0000
 +[    0.632000] 6 bcm63xxpart partitions found on MTD device spi1.0
 +[    0.640000] Creating 6 MTD partitions on "​spi1.0":​
 +[    0.644000] 0x000000000000-0x000000010000 : "​CFE"​
 +[    0.652000] 0x000000010100-0x000000146108 : "​kernel"​
 +[    0.656000] 0x000000146108-0x0000007d0000 : "​rootfs"​
 +[    0.664000] mtd: device 2 (rootfs) set to be root filesystem
 +[    0.676000] 1 squashfs-split partitions found on MTD device rootfs
 +[    0.684000] 0x000000360000-0x0000007d0000 : "​rootfs_data"​
 +[    0.692000] 0x0000007d0000-0x0000007e0000 : "​cal_data"​
 +[    0.700000] 0x0000007f0000-0x000000800000 : "​nvram"​
 +[    0.704000] 0x000000010000-0x0000007d0000 : "​linux"​
 +[    0.752000] b53_common: found switch: BCM63xx, rev 0
 +[    0.756000] bcm63xx-wdt bcm63xx-wdt: ​ started, timer margin: 30 sec
 +[    0.768000] TCP: cubic registered
 +[    0.768000] NET: Registered protocol family 17
 +[    0.776000] bridge: automatic filtering via arp/​ip/​ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
 +[    0.788000] Bridge firewalling registered
 +[    0.792000] 8021q: 802.1Q VLAN Support v1.8
 +[    0.812000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    0.836000] Freeing unused kernel memory: 1304K (8039a000 - 804e0000)
 +[    2.508000] init: Console is alive
 +[    2.512000] init: - watchdog -
 +[    3.280000] random: nonblocking pool is initialized
 +[    4.648000] init: - preinit -
 +[    5.368000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link UP on Port 3, 100Mbps, full-duplex
 +Press the [f] key and hit [enter] to enter failsafe mode
 +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
 +[    9.116000] jffs2: notice: (235) jffs2_build_xattr_subsystem:​ complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
 +[    9.148000] mount_root: switching to jffs2 overlay
 +[    9.240000] procd: - early -
 +[    9.244000] procd: - watchdog -
 +[   ​10.260000] procd: - ubus -
 +[   ​11.268000] procd: - init -
 +Please press Enter to activate this console.
 +[   ​13.884000] NET: Registered protocol family 10
 +[   ​13.960000] usbcore: registered new interface driver usbfs
 +[   ​13.968000] usbcore: registered new interface driver hub
 +[   ​13.972000] usbcore: registered new device driver usb
 +[   ​13.988000] ehci_hcd: USB 2.0 '​Enhanced'​ Host Controller (EHCI) Driver
 +[   ​14.000000] ehci-platform:​ EHCI generic platform driver
 +[   ​14.016000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​14.040000] ehci-pci: EHCI PCI platform driver
 +[   ​14.056000] ohci_hcd: USB 1.1 '​Open'​ Host Controller (OHCI) Driver
 +[   ​14.064000] ohci-platform:​ OHCI generic platform driver
 +[   ​14.076000] uhci_hcd: USB Universal Host Controller Interface driver
 +[   ​14.116000] hidraw: raw HID events driver (C) Jiri Kosina
 +[   ​14.128000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
 +[   ​14.136000] Backport generated by backports.git backports-20150129-0-gdd4a670
 +[   ​14.156000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​14.184000] nf_conntrack version 0.5.0 (953 buckets, 3812 max)
 +[   ​14.264000] xt_time: kernel timezone is -0000
 +[   ​14.332000] cfg80211: Calling CRDA to update world regulatory domain
 +[   ​14.340000] cfg80211: World regulatory domain updated:
 +[   ​14.344000] cfg80211: ​ DFS Master region: unset
 +[   ​14.348000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp), (dfs_cac_time)
 +[   ​14.360000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
 +[   ​14.368000] cfg80211: ​  ​(2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
 +[   ​14.376000] cfg80211: ​  ​(2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
 +[   ​14.384000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
 +[   ​14.392000] cfg80211: ​  ​(5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
 +[   ​14.404000] cfg80211: ​  ​(5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
 +[   ​14.412000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
 +[   ​14.420000] cfg80211: ​  ​(57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
 +[   ​14.588000] PPP generic driver version 2.4.2
 +[   ​14.596000] NET: Registered protocol family 24
 +[   ​14.836000] b43-phy0: Broadcom 43227 WLAN found (core revision 30)
 +[   ​14.844000] b43-phy0: Found PHY: Analog 9, Type 4 (N), Revision 16
 +[   ​14.852000] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
 +[   ​14.860000] Broadcom 43xx driver loaded [ Features: PNL ]
 +[   ​20.516000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link UP on Port 3, 100Mbps, full-duplex
 +[   ​26.560000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link UP on Port 3, 100Mbps, full-duplex
 +[   ​26.568000] device eth0.1 entered promiscuous mode
 +[   ​26.576000] device eth0 entered promiscuous mode
 +[   ​26.588000] br-lan: port 1(eth0.1) entered forwarding state
 +[   ​26.592000] br-lan: port 1(eth0.1) entered forwarding state
 +[   ​28.596000] br-lan: port 1(eth0.1) entered forwarding state
 </​code>​ </​code>​
 </p> </p>
Line 448: Line 771:
  
 ===== Tags ===== ===== Tags =====
-{{tag>​bcm63xx bcm6328}}+{{tag>​bcm63xx bcm6328 ​integrated NonDetachableAntenna 64RAM 8Flash 1USB USB2.0 Serial 1WNIC 802.11bgn MIPS MIPS32 bcm43227 1NIC 4Port hwVLAN FastEthernet}}
toh/arcadyan/ar7516.1351965055.txt.bz2 · Last modified: 2012/11/03 18:50 (external edit)