Easybox 904 LTE

This device is being distributed by Vodafone to their customers. It's an product of the Arcadyan Subcompany Astoria Networks.

Supported Versions

Version/Model Launch Date S/N OpenWrt Version Supported Model Specific Status
R01 - - - Work in Progress

Flash Layout

Please check out the article file_system. It contains an example and a couple of explanations.

Debricking

1. Start a TFTP Server on 192.168.2.100 and provide the fullimage.img in the root directory.
2. Hold the reset button and power on the device.
3. Hold the reset button down till the Display shows a message with fullimage.bin .
4. Release the Reset button.
5. Wait till the Easybox download and flash the Firmware.
6. If the display shows a message that say that you should reboot the device, reboot it.

Hardware

Info

Instruction set: MIPS
Vendor: Lantiq
Bootloader: U-Boot Version for Lantiq SoCs from
System-On-Chip: Lantiq
CPU @Frq MIPS 34Kc Vers. ?.? @500MHz
Flash size: 512 Mib
Flash Chip:
RAM size: 128 Mib
RAM Chip:
Wireless No1: integrated: SoC: QCA9558-AT4A w/ 3x3 MIMO for 2.4GHz 802.11bgn
Wireless No2: na
Switch: RealTek RTL8366RB Gigabit w/ vlan support + swconfig
Modem: LTE (telecommunication) see →mobile.wireless
USB: Yes 1 x 2.0 / 3.0
Serial: Yes
JTAG: Yes

Photos

Model Number

Front:

Back:

Opening the case

Note: This will void your warranty!

  • To remove the cover do a/b/c

Main PCB

Photo of PCB

Serial

port.serial general information about the serial port, serial port cable, etc.

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:

Photo of PCB with markings

Bootloader Mods

  1. you could read about bootloader in general

Bootlogs

OEM bootlog

ROM VER: 1.1.4 CFG 06 NAND NAND Read OK ROM VER: 1.1.4 CFG 06 NAND NAND Read OK nand_read_page - 00000008 DDR autotuning Rev 0.3c DDR size from 0xa0000000 - 0xa7ffffff DDR check ok... start booting... U-Boot 2010.06-Lv2.0.40-A0.3 (Jul 12 2012 - 22:00:12) CLOCK CPU 500M RAM 250M DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit) 512 MiB Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 nand_read_bbt: Bad block at 0x00000f6c0000 In: serial Out: serial Err: serial Net: Internal phy(GE) firmware version: 0x040b vr9 Switch Type "run flash_nfs" to mount root filesystem over NFS Hit any key to stop autoboot: 1  0 1. bootid : 0, bootnum : 0 Writing to Nand... Erasing at 0x4540000 -- 50% complete. Erasing at 0x4560000 -- 100% complete. done 2. bootid : 0, bootnum : 1 NAND read: device 0 offset 0x0000000001e40000, size 0x0000000000400000 0x400000 bytes read: OK ## Booting kernel from Legacy Image at 80800000 ... Image Name: MIPS LTQCPE Linux-2.6.32.32 Created: 2012-09-25 9:34:33 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1441728 Bytes = 1.4 MiB Load Address: 80002000 Entry Point: 800061b0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Lantiq xDSL CPE VR9 mips_hpt_frequency = 250000000, counter_resolution = 2

OEM bootlog (console enabled)

? ROM VER: 1.1.4 CFG 06 NAND NAND Read OK ROM VER: 1.1.4 CFG 06 NAND NAND Read OK nand_read_page - 00000008 DDR autotuning Rev 0.3c DDR size from 0xa0000000 - 0xa7ffffff DDR check ok... start booting... U-Boot 2010.06-Lv2.0.40-A0.3 (Jul 12 2012 - 22:00:12) CLOCK CPU 500M RAM 250M DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit) 512 MiB Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 nand_read_bbt: Bad block at 0x00000f6c0000 In: serial Out: serial Err: serial Net: Internal phy(GE) firmware version: 0x040b vr9 Switch Type "run flash_nfs" to mount root filesystem over NFS Hit any key to stop autoboot: 1 ??? 0 Uncompressing LCD bootup images ............... NAND read: device 0 offset 0x0000000004700000, size 0x0000000000300000 0x300000 bytes read: OK 1. bootid : 0, bootnum : 0 Writing to Nand... Erasing at 0x4540000 -- 50% complete. Erasing at 0x4560000 -- 100% complete. done 2. bootid : 0, bootnum : 1 NAND read: device 0 offset 0x0000000001e40000, size 0x0000000000400000 0x400000 bytes read: OK ## Booting kernel from Legacy Image at 80800000 ... Image Name: MIPS LTQCPE Linux-2.6.32.32 Created: 2013-08-01 21:23:56 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1441728 Bytes = 1.4 MiB Load Address: 80002000 Entry Point: 800061b0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Starting kernel ... Lantiq xDSL CPE VR9 mips_hpt_frequency = 250000000, counter_resolution = 2 [ 0.000000] Linux version 2.6.32.32 (fmk@fmk-VirtualBox) (gcc version 4.3.3 (GCC) ) #3 Thu Aug 1 23:23:34 CEST 2013 [ 0.000000] phym = 08000000, mem = 07400000, max_pfn = 00007400 [ 0.000000] Reserving memory for CP1 @0xa7400000, size 0x00c00000 [ 0.000000] CPU revision is: 00019556 (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 07400000 @ 00000000 (usable) [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00007400 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00007400 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 29464 [ 0.000000] Kernel command line: root=/dev/mtdblock1 rw rootfstype=squashfs,jffs2 ip=192.168.2.1:192.168.2.100::::eth0:on console=ttyS0,115200 ethaddr=50:7E:5D:50:D9:BC phym=128M mem=116M panic=1 mtdparts=ifx_nand:256k(uboot),30m(rootfs),4m(kernel),30m(rootfs2),4m(kernel2),1m(sysconfig),1m(ubootconfig),768k(fwdiag),3m(lcdimage),1m(mfgconfig),1m(sipdata),64m(voice),339m(misc),32m(ltefw) init=/etc/preinit vpe1_load_addr=0x87e00000 vpe1_mem=2M [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=0000b090 [ 0.000000] Readback ErrCtl register=0000b090 [ 0.000000] Memory: 113108k/118784k available (3203k kernel code, 5508k reserved, 707k data, 176k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:185 [ 0.000000] Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.000000] console [ttyS0] enabled [ 0.030000] Calibrating delay loop... 331.77 BogoMIPS (lpj=165888) [ 0.053000] Security Framework initialized [ 0.054000] Mount-cache hash table entries: 512 [ 0.061000] NET: Registered protocol family 16 [ 0.063000] [ 0.063000] ======= ifx_gpio_pin_reserve 21 (10,PCI) ======= kernel module [ 0.071000] Lantiq PCI host controller driver, version 1.2.0, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.084000] bio: create slab at 0 [ 0.087000] SCSI subsystem initialized [ 0.088000] pci 0000:00:00.0: PME# supported from D1 D2 [ 0.089000] pci 0000:00:00.0: PME# disabled [ 0.090000] pci 0000:00:0e.0: PME# supported from D0 D1 D2 D3hot [ 0.091000] pci 0000:00:0e.0: PME# disabled [ 0.092000] pci 0000:00:0e.1: PME# supported from D0 D1 D2 D3hot [ 0.093000] pci 0000:00:0e.1: PME# disabled [ 0.094000] pci 0000:00:0e.2: PME# supported from D0 D1 D2 D3hot [ 0.095000] pci 0000:00:0e.2: PME# disabled [ 0.098000] NET: Registered protocol family 8 [ 0.099000] NET: Registered protocol family 20 [ 0.100000] cfg80211: Using static regulatory domain info [ 0.101000] cfg80211: Regulatory domain: US [ 0.102000] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 0.103000] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 0.104000] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.105000] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.106000] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.107000] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.108000] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 0.109000] cfg80211: Calling CRDA for country: US [ 0.110000] Switching to clocksource MIPS [ 0.114000] NET: Registered protocol family 2 [ 0.117000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.125000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.131000] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.137000] TCP: Hash tables configured (established 4096 bind 4096) [ 0.143000] TCP reno registered [ 0.147000] NET: Registered protocol family 1 [ 0.151000] gptu: totally 6 16-bit timers/counters [ 0.156000] gptu: misc_register on minor 63 [ 0.160000] gptu: succeeded to request irq 118 [ 0.164000] gptu: succeeded to request irq 119 [ 0.169000] gptu: succeeded to request irq 120 [ 0.173000] gptu: succeeded to request irq 121 [ 0.178000] gptu: succeeded to request irq 122 [ 0.182000] gptu: succeeded to request irq 123 [ 0.187000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17 [ 0.187000] ,(c)2009 Infineon Technologies AG [ 0.197000] Lantiq CGU driver, version 1.1.27, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.204000] vpe1_mem = 200000 [ 0.207000] Wired TLB entries for Linux read_c0_wired() = 0 [ 0.215000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.220000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.226000] msgmni has been set to 221 [ 0.231000] Line: 127, function: deu_init [ 0.234000] Infineon Technologies DEU driver version 2.0.0 [ 0.240000] IFX DEU DES initialized (multiblock). [ 0.244000] IFX DEU AES initialized (multiblock). [ 0.249000] IFX DEU ARC4 initialized (multiblock). [ 0.253000] IFX DEU SHA1 initialized. [ 0.257000] IFX DEU MD5 initialized. [ 0.261000] IFX DEU SHA1_HMAC initialized. [ 0.265000] IFX DEU MD5_HMAC initialized. [ 0.269000] io scheduler noop registered (default) [ 0.280000] ifx_pmu_init: Major 252 [ 0.282000] Lantiq PMU driver, version 1.2.2, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.290000] [ 0.290000] ======= ifx_gpio_register (1,TEST) ======= kernel init [ 0.297000] [ 0.297000] ======= ifx_gpio_register (2,MEI) ======= kernel init [ 0.305000] [ 0.305000] ======= ifx_gpio_register (3,DSL-NTR) ======= kernel init [ 0.313000] [ 0.313000] ======= ifx_gpio_register (4,SSC) ======= kernel init [ 0.320000] [ 0.320000] ======= ifx_gpio_register (5,ASC0) ======= kernel init [ 0.328000] [ 0.328000] ======= ifx_gpio_register (6,SDIO) ======= kernel init [ 0.336000] [ 0.336000] ======= ifx_gpio_register (7,LEDC) ======= kernel init [ 0.343000] [ 0.343000] ======= ifx_gpio_register (8,USB) ======= kernel init [ 0.351000] [ 0.351000] ======= ifx_gpio_register (9,INT_SW) ======= kernel init [ 0.359000] [ 0.359000] ======= ifx_gpio_register (10,PCI) ======= kernel init [ 0.366000] [ 0.366000] ======= ifx_gpio_register (11,PCIE) ======= kernel init [ 0.374000] [ 0.374000] ======= ifx_gpio_register (12,NAND) ======= kernel init [ 0.382000] [ 0.382000] ======= ifx_gpio_register (13,PPA) ======= kernel init [ 0.389000] [ 0.389000] ======= ifx_gpio_register (14,TAPI-VMMC) ======= kernel init [ 0.398000] [ 0.398000] ======= ifx_gpio_register (15,TAPI-DEMO) ======= kernel init [ 0.406000] [ 0.406000] ======= ifx_gpio_register (16,TAPI-FXO) ======= kernel init [ 0.414000] [ 0.414000] ======= ifx_gpio_register (17,TAPI-DXT) ======= kernel init [ 0.422000] [ 0.422000] ======= ifx_gpio_register (18,TAPI-VCPE) ======= kernel init [ 0.430000] [ 0.430000] ======= ifx_gpio_register (19,VINAX) ======= kernel init [ 0.438000] [ 0.438000] ======= ifx_gpio_register (20,USIF-UART) ======= kernel init [ 0.446000] [ 0.446000] ======= ifx_gpio_register (21,USIF-SPI) ======= kernel init [ 0.454000] [ 0.454000] ======= ifx_gpio_register (22,SFLASH) ======= kernel init [ 0.462000] [ 0.462000] ======= ifx_gpio_register (23,EEPROM) ======= kernel init [ 0.470000] [ 0.470000] ======= ifx_gpio_register (24,USIF-SFLASH) ======= kernel init [ 0.478000] [ 0.478000] ======= ifx_gpio_register (25,LED) ======= kernel init [ 0.486000] [ 0.486000] ======= ifx_gpio_register (26,EBU_LED) ======= kernel init [ 0.494000] [ 0.494000] ======= ifx_gpio_register (27,EXIN) ======= kernel init [ 0.502000] [ 0.502000] ======= ifx_gpio_register (28,PAGE_BUTTON) ======= kernel init [ 0.510000] [ 0.510000] ======= ifx_gpio_register (29,DECT) ======= kernel init [ 0.518000] [ 0.518000] ======= ifx_gpio_register (30,SERIAL_IN) ======= kernel init [ 0.526000] [ 0.526000] ======= ifx_gpio_register (31,BUTTON) ======= kernel init [ 0.534000] [ 0.534000] ======= ifx_gpio_register (32,LCD) ======= kernel init [ 0.541000] [ 0.541000] ======= ifx_gpio_register (33,TP) ======= kernel init [ 0.549000] [ 0.549000] ======= ifx_gpio_register (34,SIPO) ======= kernel init [ 0.557000] Lantiq GPIO driver, version 1.2.14, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.564000] Infineon Technologies RCU driver version 1.0.8 [ 0.570000] [ 0.570000] ======= ifx_gpio_register (7,LEDC) ======= kernel module [ 0.578000] Lantiq LED Controller driver, version 1.0.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.586000] ttyS0 at MMIO 0xbe100c00 (irq = 105) is a IFX_ASC [ 0.592000] [ 0.592000] ======= ifx_gpio_pin_reserve 40 (31,BUTTON) ======= kernel module [ 0.601000] [ 0.601000] ======= ifx_gpio_pin_reserve 41 (31,BUTTON) ======= kernel module [ 0.609000] Register ASC (UART) to PMCU. [ 0.613000] Lantiq ASC (UART) driver, version 1.0.9, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.628000] loop: module loaded [ 0.631000] ifx_nand_init [ 0.632000] [ 0.632000] ======= ifx_gpio_pin_reserve 23 (12,NAND) ======= kernel module [ 0.641000] [ 0.641000] ======= ifx_gpio_pin_reserve 24 (12,NAND) ======= kernel module [ 0.649000] [ 0.649000] ======= ifx_gpio_pin_reserve 13 (12,NAND) ======= kernel module [ 0.658000] [ 0.658000] ======= ifx_gpio_pin_reserve 48 (12,NAND) ======= kernel module [ 0.666000] [ 0.666000] ======= ifx_gpio_pin_reserve 49 (12,NAND) ======= kernel module [ 0.674000] Probe for NAND flash... [ 0.678000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit) [ 0.688000] nand_read_bbt: Bad block at 0x00000f6c0000 [ 0.692000] 14 cmdlinepart partitions found on MTD device ifx_nand [ 0.698000] using NEW partition bias algorithm. [ 0.703000] Creating 14 MTD partitions on "ifx_nand": [ 0.707000] 0x000000000000-0x000000040000 : "uboot" [ 0.714000] 0x000000040000-0x000001e40000 : "rootfs" [ 0.719000] 0x000001e40000-0x000002240000 : "kernel" [ 0.723000] 0x000002240000-0x000004040000 : "rootfs2" [ 0.729000] 0x000004040000-0x000004440000 : "kernel2" [ 0.734000] 0x000004440000-0x000004540000 : "sysconfig" [ 0.739000] 0x000004540000-0x000004640000 : "ubootconfig" [ 0.744000] 0x000004640000-0x000004700000 : "fwdiag" [ 0.749000] 0x000004700000-0x000004a00000 : "lcdimage" [ 0.754000] 0x000004a00000-0x000004b00000 : "mfgconfig" [ 0.760000] 0x000004b00000-0x000004c00000 : "sipdata" [ 0.765000] 0x000004c00000-0x000008c00000 : "voice" [ 0.770000] 0x000008c00000-0x00001df00000 : "misc" [ 0.775000] 0x00001df00000-0x00001ff00000 : "ltefw" [ 0.780000] [ 0.780000] ======= ifx_gpio_register (4,SSC) ======= kernel module [ 0.786000] Lantiq SSC driver, version 2.2.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.794000] PPP generic driver version 2.4.2 [ 0.799000] PPP Deflate Compression module registered [ 0.803000] PPP BSD Compression module registered [ 0.808000] PPP MPPE Compression module registered [ 0.812000] NET: Registered protocol family 24 [ 0.821000] IMQ driver loaded successfully. [ 0.824000] Hooking IMQ before NAT on PREROUTING. [ 0.829000] Hooking IMQ after NAT on POSTROUTING. [ 0.834000] IFX SWITCH API, Version 1.1.7.2 [ 0.838000] SWAPI: Registered character device [switch_api] with major no [81] [ 0.845000] Switch API: PCE MicroCode loaded !! [ 0.850000] Switch Auto Polling value = 0 [ 0.864000] GPHY FW load for A2x !! [ 0.867000] GPHY FIRMWARE LOAD SUCCESSFULLY AT ADDR : 420000 [ 1.926000] IFX GPHY driver GE Mode, version ifxmips_vr9_gphy: V0.9 - Firmware: 841e [ 1.933000] Registered led device: broadband_led [ 1.938000] Registered led device: internet_led [ 1.942000] Registered led device: ledc_2 [ 1.946000] Registered led device: ledc_3 [ 1.950000] Registered led device: ledc_4 [ 1.954000] Registered led device: ledc_5 [ 1.958000] Registered led device: ledc_6 [ 1.962000] Registered led device: ledc_7 [ 1.966000] Registered led device: ledc_8 [ 1.970000] Registered led device: ledc_9 [ 1.974000] Registered led device: ledc_10 [ 1.978000] Registered led device: ledc_11 [ 1.982000] Registered led device: wps_led [ 1.986000] Registered led device: ledc_13 [ 1.990000] Registered led device: ledc_14 [ 1.995000] Registered led device: usb2_link_led [ 1.999000] Registered led device: ledc_16 [ 2.003000] Registered led device: ledc_17 [ 2.007000] Registered led device: usb1_link_led [ 2.012000] Registered led device: fxo_act_led [ 2.016000] Registered led device: internet_red_led [ 2.021000] Registered led device: voip_led [ 2.025000] Registered led device: warning_led [ 2.030000] Registered led device: ledc_23 [ 2.034000] Lantiq LED driver, version 1.0.17, (c) 2001-2011 Lantiq Deutschland GmbH [ 2.041000] u32 classifier [ 2.044000] Performance counters on [ 2.048000] Actions configured [ 2.051000] nf_conntrack version 0.5.0 (1769 buckets, 7076 max) [ 2.057000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use [ 2.065000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or [ 2.072000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it. [ 2.079000] ip_conntrack_rtsp v0.6.21 loading [ 2.083000] xt_time: kernel timezone is -0000 [ 2.089000] IPv4 over IPv4 tunneling driver [ 2.094000] GRE over IPv4 tunneling driver [ 2.100000] ip_nat_rtsp v0.6.21 loading [ 2.103000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.108000] iptables target:TRIGGER __init [ 2.112000] TCP cubic registered [ 2.115000] NET: Registered protocol family 10 [ 2.123000] lo: Disabled Privacy Extensions [ 2.134000] tunl0: Disabled Privacy Extensions [ 2.142000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 2.147000] NET: Registered protocol family 17 [ 2.151000] NET: Registered protocol family 8 [ 2.155000] atmpvc_init() failed with -17 [ 2.159000] lec.c: Aug 1 2013 12:33:58 initialized [ 2.164000] mpc.c: Aug 1 2013 12:33:54 initialized [ 2.169000] KOAM is loaded successfully. [ 2.173000] 802.1Q VLAN Support v1.8 Ben Greear [ 2.179000] All bugs added by David S. Miller [ 2.192000] VFS: Mounted root (squashfs filesystem) readonly on device 31:1. [ 2.198000] Freeing unused kernel memory: 176k freed [ 2.212000] Please be patient, while OpenWrt loads ... - preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - - config restore - config/arc-middle/register/003-mid_switch.reg config/arc-middle/register/005-mid_voip.reg config/arc-middle/register/009-mid_lte.reg config/arc-middle/register/008-mid_usb.reg config/arc-middle/register/006-mid_sys.reg config/arc-middle/register/010-mid_mon.reg config/arc-middle/register/001-mid_ccfg.reg config/arc-middle/register/007-mid_wlan.reg config/cert/Ftps/pure-ftpd.pem config/cert/WebServer/hr-webserver.key.pem config/cert/WebServer/hr-webserver.req.pem config/cert/WebServer/hr-webserver.crt.pem config/cert/RootCA/hr-rootca.req.pem config/cert/RootCA/hr-rootca.crt.pem config/cert/RootCA/hr-rootca.key.pem config/cert/authorized_keys config/cert/openssl-altname.config config/cert/dropbear_dss_host_key config/cert/openssl.config config/cert/dropbear_rsa_host_key config/iproute2/rt_tables config/system config/no_con_output.txt config/www.pool.ntp.org_zone_de.html config/ripd.conf config/ulogd.conf config/passwd config/rc.conf config/samba config/system_boot_time config/inittab.shell config/timeserver config/dropbear config/firewall config/group config/no_con_output.txt~ config/timezonelist config/task_priority config/hosts config/glbcfg.dft config/network config/dhcp config/inittab config/.glbcfg config/ntpclient config/network-3g config/inittab.noshell config/mapi_event.cfg config/arc-middle/register/ config/cert/Ftps/ config/cert/WebServer/ config/cert/RootCA/ config/arc-middle/ config/dropbear_key/ config/cert/ config/iproute2/ config/ Successfully read 64561 bytes of image sysconfig and write 64553 bytes into file /tmp/config.tgz config/ config/ntpclient config/group config/group- config/passwd config/passwd- config/firewall config/nat.user config/sysctl.conf config/firewall2.user config/network config/dhcp config/inittab config/system config/no_con_output.txt config/www.pool.ntp.org_zone_de.html config/ripd.conf config/ulogd.conf config/rc.conf config/samba config/system_boot_time config/inittab.shell config/timeserver config/dropbear config/no_con_output.txt~ config/timezonelist config/task_priority config/hosts config/glbcfg.dft config/.glbcfg config/network-3g config/inittab.noshell config/mapi_event.cfg config/dropbear_key/ config/iproute2/ config/iproute2/rt_tables config/cert/ config/cert/authorized_keys config/cert/openssl-altname.config config/cert/dropbear_dss_host_key config/cert/openssl.config config/cert/dropbear_rsa_host_key config/cert/RootCA/ config/cert/RootCA/hr-rootca.req.pem config/cert/RootCA/hr-rootca.crt.pem config/cert/RootCA/hr-rootca.key.pem config/cert/WebServer/ config/cert/WebServer/hr-webserver.key.pem config/cert/WebServer/hr-webserver.req.pem config/cert/WebServer/hr-webserver.crt.pem config/cert/Ftps/ config/cert/Ftps/pure-ftpd.pem config/arc-middle/ config/arc-middle/register/ config/arc-middle/register/003-mid_switch.reg config/arc-middle/register/005-mid_voip.reg config/arc-middle/register/009-mid_lte.reg config/arc-middle/register/008-mid_usb.reg config/arc-middle/register/006-mid_sys.reg config/arc-middle/register/010-mid_mon.reg config/arc-middle/register/001-mid_ccfg.reg config/arc-middle/register/007-mid_wlan.reg - init - parameter console value changed from ttyS0 to ttyS0 NAND write done Please press Enter to activate this console. [ 24.733000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0) [ 24.793000] fuse init (API version 7.13) in sync_samba_section!!!! [ 40.031000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH [ 40.031000] TAPI, Version 4.7.1.2, (c) 2001-2010 Lantiq Deutschland GmbH 3:ADLEY:PPA:: datapath_vr9_d5.ko ethwan=2 wanitf=8 [ 41.105000] Loading D5 (MII0/1) driver ...... Succeeded! [ 41.131000] PPE datapath driver info: [ 41.131000] Version ID: 64.3.3.1.0.1.1 [ 41.131000] Family : VR9 [ 41.131000] DR Type : Normal Data Path | Indirect-Fast Path [ 41.131000] Interface : MII0 | MII1 [ 41.131000] Mode : Routing [ 41.131000] Release : 0.1.1 [ 41.157000] PPE firmware info: [ 41.157000] Version ID: 7.2.1.6.2.0 [ 41.157000] Family : VR9 [ 41.157000] FW Type : Acceleration [ 41.157000] Interface : MII0 + MII1 [ 41.157000] Mode : Bridging + IPv4 Routing [ 41.157000] Release : 2.0 [ 41.396000] Lantiq MIPS34KEc MPS driver, version 2.2.3.1, (c) 2006-2010 Lantiq Deutschland GmbH [ 41.404000] Lantiq VMMC device driver, version 1.10.2.2, (c) 2006-2010 Lantiq Deutschland GmbH [ 41.893000] ifx_ppa_api: module license 'unspecified' taints kernel. [ 41.898000] Disabling lock debugging due to kernel taint [ 42.057000] PPA API --- init successfully [ 42.503000] ifx_ppa_init - init succeeded [ 45.770000] device eth0 entered promiscuous mode [ 46.100000] device eth0.66 entered promiscuous mode [ 46.161000] br-lan: port 1(eth0.66) entering forwarding state [ 48.504000] device eth0.71 entered promiscuous mode [ 48.596000] br-lan1: port 1(eth0.71) entering forwarding state [ 51.162000] br-lan: port 1(eth0.66) entering disabled state [ 51.395000] br-lan: port 1(eth0.66) entering forwarding state [ 51.520000] tp904_mod_init() [ 51.521000] tp904_dev_init() [ 51.524000] tp904_proc_init() [ 51.652000] [ 51.652000] ======= ifx_gpio_pin_reserve 22 (33,TP) ======= kernel module [ 51.799000] wdt_ioctl:enable watch dog timer! [ 51.864000] lcd904_mod_init() [ 51.866000] lcd904_dev_init() [ 51.869000] lcd904_fb_init() [ 51.872000] lcd904_proc_init() [ 51.875000] [ 51.875000] ======= ifx_gpio_pin_reserve 6 (32,LCD) ======= kernel module [ 51.883000] [ 51.883000] ======= ifx_gpio_pin_reserve 28 (32,LCD) ======= kernel module [ 51.891000] [ 51.891000] ======= ifx_gpio_pin_reserve 31 (25,LED) ======= kernel module [ 52.761000] [ 52.761000] ======= ifx_gpio_pin_reserve 1 (33,TP) ======= kernel module [ 52.767000] [ 52.767000] ======= ifx_gpio_pin_reserve 12 (33,TP) ======= kernel module [ 52.776000] [ 52.776000] ======= ifx_gpio_pin_reserve 11 (33,TP) ======= kernel module [ 52.836000] [ 52.836000] ======= ifx_gpio_register (27,EXIN) ======= kernel module [ 58.113000] br-lan1: port 1(eth0.71) entering disabled state [ 58.192000] br-lan1: port 1(eth0.71) entering forwarding state INSERT ARCUSB KERNEL MODULE [ 58.443000] ARCUSB: Kernel Module Initialize... [ 58.447000] ARCUSB: Init GPIOs... [ 58.450000] [ 58.450000] ======= ifx_gpio_pin_reserve 5 (8,USB) ======= kernel module [ 58.458000] arcusb_gpio_initialize> check poing 'l' [ 58.463000] [ 58.463000] ======= ifx_gpio_pin_reserve 33 (8,USB) ======= kernel module [ 58.471000] arcusb_gpio_initialize> check poing 'l' [ 58.476000] [ 58.476000] ======= ifx_gpio_pin_reserve 14 (8,USB) ======= kernel module [ 58.484000] arcusb_gpio_initialize> check poing 'l' [ 58.489000] [ 58.489000] ======= ifx_gpio_pin_reserve 20 (8,USB) ======= kernel module [ 58.497000] arcusb_gpio_initialize> check poing 'l' [ 58.502000] [ 58.502000] ======= ifx_gpio_pin_reserve 39 (8,USB) ======= kernel module [ 59.362000] TRACE> isdn_init [ 59.362000] ISDN Driver, Rev. 1.0r1, (c) 2011-2013 Arcadyan Technology Corp. [ 59.370000] [ 59.370000] ======= ifx_gpio_pin_reserve 15 (16,TAPI-FXO) ======= kernel module [ 59.379000] [ 59.379000] ======= ifx_gpio_pin_reserve 10 (16,TAPI-FXO) ======= kernel module [ 59.388000] [ 59.388000] ======= ifx_gpio_pin_reserve 9 (16,TAPI-FXO) ======= kernel module [ 59.397000] [ 59.397000] ======= ifx_gpio_pin_reserve 17 (16,TAPI-FXO) ======= kernel module [ 59.405000] [ 59.405000] ======= ifx_gpio_pin_reserve 18 (16,TAPI-FXO) ======= kernel module [ 59.414000] [ 59.414000] ======= ifx_gpio_pin_reserve 16 (16,TAPI-FXO) ======= kernel module [ 59.423000] TRACE> [ 59.423000] isdn_init: CHRDEV registration completed successfully [ 59.423000] copy gConfig and gSetting begin. [ 59.514000] copy gConfig and gSetting end. [ 59.520000] ARCUSB: Init Host Controllers and others... [ 59.525000] [USB] UsbSMem: need 59360 bytes [ 59.529000] [USB] UsbMMem: need 41472 bytes [ 59.533000] [USB] UsbLMem: need 126976 bytes [ 59.538000] [USB] UsbSMem: 85DD0000H ~ 85DDE7DFH [ 59.542000] [USB] UsbMMem: 85010000H ~ 8501A1FFH [ 59.547000] [USB] UsbLMem: 85EC0000H ~ 85EDEFFFH [ 59.551000] [USB] UsbSMemLink: 85DA6000H ~ 85DA7CE7H [ 59.556000] [USB] UsbMMemLink: 85C64000H ~ 85C6463FH [ 59.561000] [USB] UsbLMemLink: 86E9EC00H ~ 86E9EE57H [ 59.567000] arcusb_mem: at 0x85200000 allocate 1147968 bytes ... OK [ 59.573000] arcusb_mem: at 0x85320000 allocate 119540 bytes ... OK [ 59.579000] arcusb_mem: short-cut, 10340640 bytes pre-allocated, UsbMPool @ 87400000 [ 59.586000] arcusb_mem: at 0x853c0000 allocate 50060 bytes ... OK [ 59.593000] arcusb_mem: at 0x84c00000 allocate 1131520 bytes ... OK [ 59.599000] arcusb_mem: at 0x84dff000 allocate 1260 bytes ... OK [ 59.605000] [USB] Small Un-Cached Memory(5977): 85200020 ~ 853182DF [ 59.611000] [USB] Medium Un-Cached Memory(2503): 87400020 ~ 87DDA8FF [ 59.617000] [USB] Large Un-Cached Memory(63): 84C00020 ~ 84D0BC1F [ 59.624000] 31041106 02100000 0c032065 00801600 18000000 00000000 00000000 00000000 [ 59.631000] 00000000 00000000 00000000 31041106 00000000 00000080 00000000 00000300 [ 59.639000] 000b0000 00000000 090020a0 ffff0000 80005a00 00000000 88880b04 00000033 [ 59.647000] 00012020 00000000 00000001 80000000 00000000 00000000 00000000 00000000 [ 59.655000] 7e0a0001 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.662000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.670000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.678000] 00000000 00000000 00000000 00000000 00000000 03000000 00000000 00000000 [ 59.685000] [ 59.687000] setUsbPciInfo() cpu_to_usb_addr_shift[4]:0x60000000, usb_to_cpu_addr_shift[4]:0xa0000000 [ 59.696000] usb_pci_probe() Found VIA EHCI device in PCI slot 0x72, function 2, baseAddr:0xb8000000, IRQ:22 [ 59.706000] 30381106 02100000 0c030062 00801600 00000000 00000000 00000000 00000000 [ 59.713000] 1ae00001 00000000 00000000 30381106 00000000 00000080 00000000 00000116 [ 59.721000] 00031040 00000000 00000800 00000000 00000000 00000000 00000000 00000000 [ 59.729000] 00000010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.737000] 7e0a0001 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.744000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.752000] 00002000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.760000] 00000000 00000000 00000000 00000000 00000000 03000000 00000000 00000000 [ 59.768000] [ 59.769000] setUsbPciInfo() cpu_to_usb_addr_shift[0]:0x60000000, usb_to_cpu_addr_shift[0]:0xa0000000 [ 59.778000] usb_pci_probe() Found VIA UHCI-1 device in PCI slot 0x70, function 0, baseAddr:0xbae00000, IRQ:100000 [ 59.788000] 30381106 02100000 0c030062 00801600 00000000 00000000 00000000 00000000 [ 59.796000] 1ae00021 00000000 00000000 30381106 00000000 00000080 00000000 00000200 [ 59.804000] 00031040 00000000 00000800 00000000 00000000 00000000 00000000 00000000 [ 59.812000] 00000010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.819000] 7e0a0001 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.827000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.835000] 00002000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 59.842000] 00000000 00000000 00000000 00000000 00000000 03000000 00000000 00000000 [ 59.850000] [ 59.852000] setUsbPciInfo() cpu_to_usb_addr_shift[1]:0x60000000, usb_to_cpu_addr_shift[1]:0xa0000000 [ 59.861000] usb_pci_probe() Found VIA UHCI-2 device in PCI slot 0x71, function 1, baseAddr:0xbae00020, IRQ:100000 [ 59.871000] setUsbPciInfo() cpu_to_usb_addr_shift[5]:0x00000000, usb_to_cpu_addr_shift[5]:0x00000000 [ 59.880000] usb_pci_probe() Found Synopsis OTG-1, baseAddr:0xbe101000, IRQ:54 [ 59.887000] setUsbPciInfo() cpu_to_usb_addr_shift[6]:0x00000000, usb_to_cpu_addr_shift[6]:0x00000000 [ 59.896000] usb_pci_probe() Found Synopsis OTG-2, baseAddr:0xbe106000, IRQ:48 [ 59.903000] usb_hcd_init() probe PCI function:5 !! [ 59.908000] usb_host_power_set() Previous power off:0, current time:59908 [ 59.915000] usb_host_power_set(1) min time delay:6000, current delay:59908 [ 59.922000] usb_host_power_set(2) min time delay:6000, current delay:59922 [ 59.929000] usb_hcd_init() func(0):1 [ 59.932000] localhc_init() install uhci driver(host_drv = 0xC1C1CC48, uhci_driver=0xC1C1CC48). [ 59.941000] usb_pci_attach_device() Enable PCI device...PCI: Enabling device 0000:00:0e.0 (0000 -> 0001) [ 59.950000] OK [ 59.950000] usb_pci_attach_device() Set latency timer...OK [ 59.957000] usb_pci_attach_device() Set bus master...OK [ 59.962000] usb_pci_attach_device() Set VIA-UHCI special parameters...OK [ 59.969000] usb_pci_attach_device(UHCI) Attach succ... [ 59.975000] 30381106 02100005 0c030062 00801600 00000000 00000000 00000000 00000000 [ 59.982000] 1ae00001 00000000 00000000 30381106 00000000 00000080 00000000 00000116 [ 59.990000] 00030040 00000000 00000800 00000000 00000000 00000000 00000000 00000000 [ 59.998000] 00000010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.005000] 7e0a0001 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.013000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.021000] 00002000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.029000] 00000000 00000000 00000000 00000000 00000000 03000000 00000000 00000000 [ 60.036000] [ 60.038000] usb_hcd_init() func(1):1 [ 60.041000] localhc_init() install uhci driver(host_drv = 0xC1C1CC48, uhci_driver=0xC1C1CC48). [ 60.050000] usb_pci_attach_device() Enable PCI device...PCI: Enabling device 0000:00:0e.1 (0000 -> 0001) [ 60.059000] OK [ 60.059000] usb_pci_attach_device() Set latency timer...OK [ 60.066000] usb_pci_attach_device() Set bus master...OK [ 60.071000] usb_pci_attach_device() Set VIA-UHCI special parameters...OK [ 60.078000] usb_pci_attach_device(UHCI) Attach succ... [ 60.084000] 30381106 02100005 0c030062 00801600 00000000 00000000 00000000 00000000 [ 60.091000] 1ae00021 00000000 00000000 30381106 00000000 00000080 00000000 00000200 [ 60.099000] 00030040 00000000 00000800 00000000 00000000 00000000 00000000 00000000 [ 60.107000] 00000010 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.114000] 7e0a0001 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.122000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.130000] 00002000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.138000] 00000000 00000000 00000000 00000000 00000000 03000000 00000000 00000000 [ 60.145000] [ 60.147000] usb_hcd_init() func(2):0 [ 60.150000] usb_hcd_init() func(3):0 [ 60.154000] usb_hcd_init() func(4):1 [ 60.157000] localhc_init() install ehci driver(host_drv = 0xC1C1CAD0, ehci_driver=0xC1C1CAD0). [ 60.166000] usb_pci_attach_device() Enable PCI device...PCI: Enabling device 0000:00:0e.2 (0000 -> 0002) [ 60.176000] OK [ 60.176000] usb_pci_attach_device() Set latency timer...OK [ 60.182000] usb_pci_attach_device() Set bus master...OK [ 60.188000] usb_pci_attach_device() Set write invalidate...OK [ 60.193000] usb_pci_attach_device() Set VIA-EHCI special parameters...OK [ 60.200000] usb_pci_attach_device(EHCI) Attach succ... [ 60.205000] 31041106 02100016 0c032065 00801600 18000000 00000000 00000000 00000000 [ 60.213000] 00000000 00000000 00000000 31041106 00000000 00000080 00000000 00000300 [ 60.221000] 000b0000 00000000 290020a0 ffff0000 80005a00 00000000 88880b04 00000033 [ 60.229000] 00012020 00000000 00000001 c0000000 00000000 00000000 00000000 00000000 [ 60.236000] 7e0a0001 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.244000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.252000] 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 60.259000] 00000000 00000000 00000000 00000000 00000000 03000000 00000000 00000000 [ 60.267000] [ 60.269000] usb_hcd_init() func(5):1 [ 60.272000] localhc_init() install otg driver(host_drv = 0xC1C1C990, otg_driver=0xC1C1C990). [ 60.281000] usb_hcd_init() func(6):1 [ 60.284000] localhc_init() install otg driver(host_drv = 0xC1C1C990, otg_driver=0xC1C1C990). [ 60.293000] usb_hcd_init(): succ. [ 62.783000] ifx_ppa_init - init succeeded check mtd wifi config ok! [ 66.325000] Run a kernel thread "UsbSysInitTask" success (PID: 5044) (curr nice 0) (kdata 0x00000000) [ 66.333000] [ 66.333000] [ 66.333000] arcusb_chrdev: add a new char device "umtsCS" OK. [ 66.333000] [ 66.343000] Test add a chrdev "umtsCS", ret=0 [ 66.347000] [ 66.347000] [ 66.347000] arcusb_chrdev: add a new char device "lp0" OK. [ 66.347000] [ 66.357000] Test add a chrdev "lp0", ret=0 [ 66.372000] Run a kernel thread "xSpeedTask" success (PID: 5584) (curr nice 0) (kdata 0x00000000) [ 66.468000] Run a kernel thread "FlushCacheTask" success (PID: 5587) (curr nice 0) (kdata 0x00000000) [ 66.510000] Run a kernel thread "usb_hc_timer_task" success (PID: 5592) (curr nice 0) (kdata 0x00000000) START ARCADYAN USB SUBSYSTEM [ 66.759000] uhci_pci_attach: begin ... [ 67.077000] uhci_init() UHCI_FRAMELIST_COUNT=1024, alloc size:4096 [ 67.082000] uhci_init() UHCI_FLBASEADDR:0x04c89000, physicalMem:0x04c89000 [ 67.191000] ?[1;32m [ 67.191000] [ 67.191000] >>>>>> usbd_new_device: adding unit bus:1, addr=1, rev=0100, class=9, subclass=0, protocol=0, maxpacket=64, len=18, speed=2 [ 67.191000] [ 67.191000] ?[0musbd_new_device() addr:1, vid:0x0000, pid:0x0000, devFlag:0x0000 [ 67.214000] usbd_open_pipe_intr: addr:1, ep address=0x81 flags=0x4 len=1 [ 67.221000] usbd_open_pipe_intr: ipipe=85dd0e60 repeat=0 xfer=a7c4c7a0 ###################################################### # # # BOOT FROM IMAGE 1 # # # ###################################################### diag_port@lte was existed, its value is 30000 Current LTE prefernet config 8 Current UMTS prefernet config 0 [ 67.788000] usbd_probe_and_attach,probe 1! [ 67.790000] uhci_pci_attach: begin ... [ 68.070000] uhci_init() UHCI_FRAMELIST_COUNT=1024, alloc size:4096 [ 68.074000] uhci_init() UHCI_FLBASEADDR:0x04cb7000, physicalMem:0x04cb7000 [ 68.183000] ?[1;32m [ 68.183000] [ 68.183000] >>>>>> usbd_new_device: adding unit bus:2, addr=1, rev=0100, class=9, subclass=0, protocol=0, maxpacket=64, len=18, speed=2 [ 68.183000] [ 68.183000] ?[0musbd_new_device() addr:1, vid:0x0000, pid:0x0000, devFlag:0x0000 [ 68.206000] usbd_open_pipe_intr: addr:1, ep address=0x81 flags=0x4 len=1 [ 68.213000] usbd_open_pipe_intr: ipipe=85dd1360 repeat=0 xfer=a7c4e7e0 [ 68.663000] usbd_probe_and_attach,probe 1! [ 68.665000] ehci_pci_attach: begin ... [ 68.669000] ehci_pci_attach: ioregs:0xb8000000, irq:22 [ 68.758000] ehci_init() flsize=1024, alloc size:4096 [ 68.761000] ehci_init() EHCI_PERIODICLISTBASE:0x04ce5000, physicalMem:0x04ce5820, EHCI_INTRQHS:255 [ 68.771000] ehci_init() sqh->physaddr:0x07c57722 [ 68.775000] ehci_init() EHCI_ASYNCLISTADDR:0x07c57720, physicalMem:0x07c57720 [ 69.210000] ?[1;32m [ 69.210000] [ 69.210000] >>>>>> usbd_new_device: adding unit bus:3, addr=1, rev=0200, class=9, subclass=0, protocol=1, maxpacket=64, len=18, speed=3 [ 69.210000] [ 69.210000] ?[0musbd_new_device() addr:1, vid:0x0000, pid:0x0000, devFlag:0x0000 [ 69.233000] usbd_probe_and_attach(Hub)> Reopen STATIC default pipe OK [ 69.240000] usbd_open_pipe_intr: addr:1, ep address=0x81 flags=0x4 len=1 [ 69.246000] usbd_open_pipe_intr: ipipe=85dd1c20 repeat=0 xfer=a7c57900 ltqppa@lte was existed, its value is on IPV6 module disable, apply 1 to LTE data. IPV6 module disable, apply 1 to LTE voice. IPV6 module disable, apply 1 to UMTS data. [ 70.106000] ARCUSB: setup "backup_mode" = "0" successfully. [ 70.110000] ARCUSB: set backup_mode to 0 [ 70.211000] ARCUSB: setup "lte_allow_mid" = "-1" successfully. [ 70.299000] ARCUSB: setup "umts_allow_mid" = "2,34,37,42,59" successfully. [ 70.304000] ARCUSB: Add mid:34, Success !! [ 70.308000] ARCUSB: Add mid:37, Success !! [ 70.313000] ARCUSB: Add mid:42, Success !! [ 70.317000] ARCUSB: Add mid:59, Success !! [ 70.556000] ARCUSB: setup "dataAPN" = "fixed.data.vodafone.de" successfully. [ 70.702000] ARCUSB: setup "voiceAPN" = "fixed.voice.vodafone.de" successfully. [ 70.798000] ARCUSB: setup "PIN" field FAILED!!!!! [ 70.840000] ARCUSB: setup "PINenb" field FAILED!!!!! [ 70.870000] ARCUSB: setup "dataIP_type" = "1" successfully. [ 70.874000] ARCUSB: set dataIP_type as 1 [ 70.941000] ARCUSB: setup "umtsAPN" = "web.vodafone.de" successfully. [ 70.998000] ARCUSB: setup "umtsPIN" field FAILED!!!!! [ 71.023000] ARCUSB: setup "umtsPINenb" = "0" successfully. [ 71.027000] ARCUSB: set umtsPINenb to 0 [ 71.069000] ARCUSB: setup "umtsPhoneNumer" field FAILED!!!!! [ 71.099000] ARCUSB: setup "umtsIdleTime" field FAILED!!!!! moremsg@lte was existed, its value is 0x00000000 expert_mode@lte was existed, its value is off manual_mode@lte was existed, its value is off mptest_lte@lte was existed, its value is off [ 71.157000] ARCUSB: setup "explore" = "on" successfully. [ 71.531000] usbd_probe_and_attach,probe 1! [ 71.533000] [USB] dwc3884_start() Core id:0, funcIdx:5 [ 71.538000] *IFX_CGU_IF_CLK 10e10006 [ 71.643000] setSynopsisPower() set power... [ 71.645000] setSynopsisPower() USB PHY configurations... [ 71.651000] setSynopsisPower() set PMU... [ 71.660000] [USB] dwc3884_start() DWC3884 core version:0x4F54281A, 2.81a, channel:16 [ 71.666000] [USB] dwc3884_reset(XR9) Reset In, core_id:0 [ 71.671000] [USB] dwc3884_reset(VR9) IFX_RCU_USB0_CFG:0xBF203018, var:0x00001480 [ 71.679000] [USB] dwc3884_reset(VR9) IFX_RCU_USB1_CFG:0xBF203034, var:0x00001400 [ 71.686000] [USB] dwc3884_reset(VR9) IFX_RCU_RST_REQ:0xBF203010 [ 73.200000] [USB] dwc3884_reset() rstctl:0xBE101010 [ 74.877000] [USB] dwc3884_start() intsts:0xBE101014, var:0x54000029 [ 77.990000] Warnning!! syncmiimac is foreced to 0 in dual concurrent mode. [ 77.996000] RT3883iNIC: 802.11n WLAN MII driver v2.5.1.0 (Feb. 2, 2012) [ 78.003000] No card information file. [ 78.003000] Use default profile path. [ 78.010000] Update MAC(0)=50:7e:5d:50:d9:c2 [ 78.014000] ============= Init Thread =================== [ 78.019000] RacfgTaskThread pid = 6428 [ 78.023000] RacfgBacklogThread pid = 6429 [ 78.027000] Org bridge hook = 802ea7f8 [ 78.031000] Change bridge hook = c2151390 [ 78.044000] ra0: Ralink iNIC at 0x0, 50:7e:5d:50:d9:c2 [ 78.047000] Update MAC(0)=50:7e:5d:50:d9:c4 [ 78.052000] ============= Init Thread =================== [ 78.057000] RacfgTaskThread pid = 6430 [ 78.061000] RacfgBacklogThread pid = 6431 [ 78.074000] rai0: Ralink iNIC at 0x0, 50:7e:5d:50:d9:c4 smb_sharemode_add DRV_DATA = 0:0:0::: DRV_DATA = 0:0:0::: DRV_DATA = 0:0:0::: [ 79.995000] This vid exists DRV_DATA = 0:0:0::: DRV_DATA = [ 82.220000] Run a kernel thread "usb_hc_timer_child_task" success (PID: 6883) (curr nice 0) (kdata 0xC1C28DE0) [ 84.607000] VPE loader: VPE1 running successfully [ 84.809000] WARN! IOCTL 8bef ignored (interface not opened yet) [ 85.584000] iNIC Open ra0 [ 85.586000] Reset GPIO,iGpioId=30 iMod=0 [ 86.859000] Op mode = 1 [ 86.860000] Read profile[0] CLOCK_MONOTONIC, resolution=0.1 System clock_res=1000000, clock_hz=1000 httpd: after config_httpd() [ 87.385000] BssidNum=2 [ 87.388000] Read profile[1] [ 87.390000] BssidNum=2 [ 87.393000] rlk_inic_mbss_init ---> [ 87.395000] Register MBSSID IF (ra1) [ 87.409000] rlk_inic_mbss_init <--- [ 87.412000] Wait for boot done... [ 87.639000] ?[1;32m [ 87.639000] [ 87.639000] >>>>>> usbd_new_device: adding unit bus:4, addr=1, rev=0200, class=9, subclass=0, protocol=1, maxpacket=64, len=18, speed=3 [ 87.639000] [ 87.639000] ?[0musbd_new_device() addr:1, vid:0x058b, pid:0xf002, devFlag:0x0000 [ 87.662000] usbd_probe_and_attach(Hub)> Reopen STATIC default pipe OK [ 87.669000] usbd_open_pipe_intr: addr:1, ep address=0x81 flags=0x4 len=1 [ 87.675000] usbd_open_pipe_intr: ipipe=85dd2260 repeat=0 xfer=a7c59940 lcdwizard(init.d) : boot lcdwizard(init.d) : start : check if (mptest) lcdwizard(init.d) : no mptest, check if (/dev/fb0) lcdwizard(init.d) : /dev/fb0 is exist, goto /usr/sbin, execute lcdwizard lcdwizard(init.d) : start : exit if [ 87.830000] RACFG_CMD_BOOT_NOTIFY [ 87.833000] Open file: /tmp/iNIC_ap.bin [ 87.836000] Open file: /tmp/iNIC_ap.dat [ 87.840000] Open file: /tmp/iNIC_e2p.bin [ 87.844000] Open file: /tmp/iNIC_ap1.dat [ 87.848000] Open file: /tmp/iNIC_e2p1.bin [ 88.062000] usbd_probe_and_attach,probe 1! [ 88.064000] [USB] dwc3884_start() Core id:1, funcIdx:6 [ 88.075000] [USB] dwc3884_start() DWC3884 core version:0x4F54281A, 2.81a, channel:16 [ 88.081000] [USB] dwc3884_reset(XR9) Reset In, core_id:1 [ 88.086000] [USB] dwc3884_reset() rstctl:0xBE106010 [ 88.266000] [USB] dwc3884_start() intsts:0xBE106014, var:0x54000029 [ 88.831000] RACFG_CMD_BOOT_INITCFG(0) [ 88.835000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 88.839000] RACFG_CMD_BOOT_INITCFG(1) [ 88.845000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 88.849000] RACFG_CMD_BOOT_INITCFG(2) [ 88.916000] stollmann_isdn: loading module [ 88.919000] Stollmann E+V GmbH ISDN-Stack V4.001 Oct 28 2011 [ 88.925000] (c) Copyright Stollmann E+V GmbH [ 88.929000] isdn_avr.lnxhwInit (c250c0bc): enter .. [ 88.934000] ISDN_initialize: Initialize BSP here.... [ 89.098000] upload_timeout[1] [ 89.099000] TRACE> IPACX TE r64=0x1 [ 89.099000] RACFG_CMD_BOOT_INITCFG(2) [ 89.106000] TRACE> IPACX NT r64=0x1 [ 89.106000] [ 89.112000] isdn_avr.lnxhwAVRDetect IPACX Chip-ID=0x1 [ 89.116000] isdn_avr.lnxhwAVRDetect: iNbr=0, IntNbr=0 [ 89.121000] isdn_avr.lnxhwAVRDoPostInit: ISDN-CHIP(1) found at address=0xb0000000 [ 89.129000] isdn_avr.lnxhwAVRDetect IPACX Chip-ID=0x1 [ 89.134000] isdn_avr.lnxhwAVRDetect: iNbr=1, IntNbr=0 [ 89.139000] isdn_avr.lnxhwAVRDoPostInit: ISDN-CHIP(2) found at address=0xb1000000 [ 89.153000] isdn_avr.lnxhwAVRDoPostInit: iLineIF=1 protocol=0xc3 IInit=1 l1Mode=0 S0BusConf=0 g711Law=1(disable=1) [ 89.162000] isdn_avr.lnxhwAVRDoPostInit: iLineIF=2 protocol=0xc2 IInit=3 l1Mode=2 S0BusConf=1 g711Law=1(disable=0) [ 89.172000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 89.177000] RACFG_CMD_BOOT_INITCFG(3) [ 89.189000] isdn_avr.hwInterruptInit: iIndex=0 [ 89.192000] isdn_avr.lnxhwAVRRequestInterruptVector: request_irq; idx=0, lvl=0, flags=20, intHandler=c250bce4 [ 89.202000] ISDN_request_irq: 0 c250bce4 20 isdn_avr c25281d8 [ 89.208000] isdn_avr.hwInterruptInit: rcvd irq for lvl=0 for IPACX 0 [ 89.217000] isdn_avr.lnxhwAVRDoPostInit/firmwareStart() OK. [ 89.238000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 89.255000] RACFG_CMD_BOOT_INITCFG(4) [ 89.258000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 89.268000] RACFG_CMD_BOOT_INITCFG(5) [ 89.271000] ziv: __SkipIfNotINIC__CONCURRENT_ENABLE [ 89.275000] Send Init Cfg Data Done(6 packets) [ 89.280000] RACFG_CMD_BOOT_UPLOAD(0) [ 89.320000] RACFG_CMD_BOOT_UPLOAD(1) [ 89.323000] RACFG_CMD_BOOT_UPLOAD(2) [ 89.576000] ?[1;32m [ 89.576000] [ 89.576000] >>>>>> usbd_new_device: adding unit bus:5, addr=1, rev=0200, class=9, subclass=0, protocol=1, maxpacket=64, len=18, speed=3 [ 89.576000] [ 89.576000] ?[0musbd_new_device() addr:1, vid:0x058b, pid:0xf002, devFlag:0x0000 [ 89.599000] usbd_probe_and_attach(Hub)> Reopen STATIC default pipe OK [ 89.606000] usbd_open_pipe_intr: addr:1, ep address=0x81 flags=0x4 len=1 [ 89.612000] usbd_open_pipe_intr: ipipe=85dd28a0 repeat=0 xfer=a7c5b980 [ 89.941000] usbd_probe_and_attach,probe 1! [ 89.947000] Run a kernel thread "usb_explore_task" success (PID: 7306) (curr nice 0) (kdata 0xC1C28DE0) [ 89.955000] startExplore() usb explore task run-up, slot:0, tsk_id:7306, reason:0 [ 89.962000] usb_hc_install_interrupt() Interrupt disable [ 89.967000] usb_hc_install_interrupt() Interrupt disable [ 89.973000] usb_hc_install_interrupt() Install EHCI interrupt 22 [ 89.979000] usb_ehci_isr_install() VIA-EHCI Interrupt request IRQ-22 OK [ 89.985000] usb_hc_install_interrupt() Install OTG-1 interrupt 54 [ 89.991000] usb_hc_install_interrupt() Install OTG-2 interrupt 83 [ 89.998000] ?[1;32mUSB Module: Version 2.0.0 build Oct 18 2012 13:39:43 [ 89.998000] ?[0musb_explore_task() Begin ... [ 90.010000] [ 90.010000] [ 90.013000] *************************************************** [ 90.019000] * THIS IS A STABLE ARCUSB SUBSYSTEM. * [ 90.025000] * Oct 18 2012 13:40:04 * [ 90.031000] *************************************************** [ 90.031000] [ 90.038000] usb_explore_task> START USB_EXPLORE_TASK... [ 90.074000] [ 90.074000] CRC:01 08 14 18 78 8f f0 6b 22 32 2e 35 2e 30 2e 35 22 00 00 00 32 30 31 32 30 36 32 35 00 00 00 00 00 00 00 00 0c 6f 08 00 [ 90.106000] Send RT3883iNIC Firmware Done [ 90.108000] =================================== [ 90.113000] version: "2.5.0.5" [ 90.116000] size: 552716 bytes [ 90.119000] date: 20120625 [ 90.122000] =================================== [ 90.122000] [ 90.128000] Send STARTUP to RT3883iNIC [ 90.132000] Close Firmware file [ 90.135000] RACFG_CMD_BOOT_STARTUP [ 90.176000] uhub_explore(4.5): port 1 change, need check: status(0x0308), change(0x0003)... [absread] : read() fails, return 0 httpd: listen at 192.168.2.1:80 [ 90.214000] uhub_explore(4.5): port 2 change, need check: status(0x0308), change(0x0003)... httpd id=1026 listen at 192.168.2.1:80 /usr/sbin/httpd-brn: initialization complete! main: http_redir_init initialization complete! [ 90.245000] capifs: Rev 1.1.2.3 [ 90.579000] uhub_explore(4.5): port 1 change, need check: status(0x0308), change(0x0003)... [ 90.617000] uhub_explore(4.5): port 2 change, need check: status(0x0308), change(0x0003)... < winmain.c@ main: 92>: Begin < scr_fb.c@ fb_open: 242>: 320x240x16bpp linelen 640 type 0 visual 2 colors 65536 pixtype 5 < winmain.c@ main: 117>: Call WinMain -------------------- lcdwizard @WinMain() : before MwInitializeDialogs() -------------------- -------------------- lcdwizard @WinMain() : ret_MwInitDialog=1 -------------------- mapi_ccfg_get_str2 language@lcd = german lcdwizard (GetScreenBrightness) : (OK) ScreenBrightness@lcd = 16 mapi_ccfg_get_long FontSize@lcd = 0 [ 91.298000] capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs) [ 91.465000] uhub_explore(4.5): port 1 change, need check: status(0x0101), change(0x0001)... [ 92.681000] usbd_transfer_cb: short transfer 18<64 [ 92.688000] ?[1;32m [ 92.688000] [ 92.688000] >>>>>> usbd_new_device: adding unit bus:4, addr=2, rev=0200, class=0, subclass=0, protocol=0, maxpacket=64, len=18, speed=3 [ 92.688000] [ 92.688000] ?[0mmapi_ccfg_get_long ivr_mode@bootstrap = 0 -------------------- lcdwizard @WinMain() : before enter DialogBox -------------------- usbd_new_device() addr:2, vid:0x0408, pid:0xea24, devFlag:0x0001 [ 92.793000] usbd_check_new_device_block(v:0x0408/p:0xea24) depth:1, portno:1, confsNum:1, nifaces:5 [ 92.800000] usbd_check_new_device_block(0) idx:0, iNum:0, Original iClass:ff, isClass:ff, iProto:ff, iFaces:00 [ 92.810000] usbd_check_new_device_block(0) idx:0, iNum:0, iClass:f3, isClass:94, iProto:01, iFaces:00 [ 92.819000] usbd_check_new_device_block(0) idx:0, ifStr:[], epCnt:2 [ 92.865000] ucdc_attach() vendor:[Qualcomm, Incorporated/0x51 0x75], product:[Qualcomm CDMA Technologies MSM/0x51 0x75], sn:[/0x00 0x62] [ 92.876000] uumts_attach(0) UMTS vendor:[], Model:[], ifnum:5 [ 92.882000] getUMTSVendorSpecifyModelInfo() UPdate UMTS vendor:[Quanta], Model:[1KG], i:4, mid:75 [ 92.891000] searchUMTSFunction(Modem)0 ifno:2, ifStr:[], epCnt:3 [ 92.897000] uumts_attach(Modem)> find all the endpoints, ifno:2, in:0x84, out:0x03, i_in:0x83 [ 92.906000] searchUMTSFunction(AT)0 ifno:1, ifStr:[], epCnt:2 [ 92.912000] uumts_attach(AT)> find all the endpoints, ifno:1, in:0x82, out:0x02, i_in:0xffffffff [ 92.921000] searchUMTSFunction(Voice)> interface disable... [ 92.926000] searchUMTSFunction(Diag)0 ifno:0, ifStr:[], epCnt:2 [ 92.933000] uumts_attach(Diag)> find all the endpoints, ifno:0, in:0x81, out:0x01, i_in:0xffffffff [ 92.942000] searchUMTSFunction(NDIS1)0 ifno:3, ifStr:[], epCnt:3 [ 92.948000] uumts_attach(NDIS1)> find all the endpoints, ifno:3, in:0x86, out:0x04, i_in:0x85 [ 92.957000] searchUMTSFunction(NDIS2)0 ifno:4, ifStr:[], epCnt:3 [ 92.963000] uumts_attach(NDIS2)> find all the endpoints, ifno:4, in:0x88, out:0x05, i_in:0x87 [ 92.972000] ******************** if_umts_reinit(1) set to IPOU-NDIS + DHCP, state:0x00000002 [ 92.980000] !!! ipou_shut() is UNDER-TO-DO !!! (func: if_umts_reinit()) [ 92.987000] !!! CHECK ipou_init() IS NEEDED !!! (func: if_umts_reinit) [ 93.176000] Run a kernel thread "sc0.umtsEventHandleTsk" success (PID: 7439) (curr nice 0) (kdata 0xC1C28D70) [ 93.194000] Run a kernel thread "sc0.umtsEventExeHandleTsk" success (PID: 7452) (curr nice 0) (kdata 0xC1C28DFC) [ 93.215000] Run a kernel thread "1.umtsReceQueueTsk" success (PID: 7453) (curr nice 0) (kdata 0xC1C28E18) [ 93.232000] Run a kernel thread "1.umtsReceTsk" success (PID: 7455) (curr nice 0) (kdata 0xC1C28E34) [ 93.239000] umtsReceTsk(7455) ifno:1, Start... [ 93.244000] umtsReceTsk(7455) pdp_id:1, ifIdx:0, upEvt:57, sc_idx:0 [ 93.259000] Run a kernel thread "1.umtsWritTsk" success (PID: 7457) (curr nice 0) (kdata 0xC1C28E50) [ 93.277000] Run a kernel thread "1.umtsDataIntrTsk" success (PID: 7458) (curr nice 0) (kdata 0xC1C28E6C) [ 93.285000] ******************** if_umts_reinit(2) set to IPOU-NDIS + DHCP, state:0x00000002 [ 93.294000] !!! ipou_shut() is UNDER-TO-DO !!! (func: if_umts_reinit()) [ 93.300000] !!! CHECK ipou_init() IS NEEDED !!! (func: if_umts_reinit) [ 93.356000] Run a kernel thread "2.umtsReceQueueTsk" success (PID: 7461) (curr nice 0) (kdata 0xC1C28E88) [ 93.374000] Run a kernel thread "2.umtsReceTsk" success (PID: 7466) (curr nice 0) (kdata 0xC1C28EA4) [ 93.382000] umtsReceTsk(7466) ifno:2, Start... [ 93.386000] umtsReceTsk(7466) pdp_id:2, ifIdx:1, upEvt:58, sc_idx:0 [ 93.401000] Run a kernel thread "2.umtsWritTsk" success (PID: 7468) (curr nice 0) (kdata 0xC1C28EC0) [ 93.421000] Run a kernel thread "2.umtsDataIntrTsk" success (PID: 7469) (curr nice 0) (kdata 0xC1C28EDC) [ 93.774000] open_umts_function(2-Modem)> open the Bulk-IN pipe...OK, xfer:0xa7c5a960, buf:0x(null), pipe:0x85dd3160 [ 93.787000] open_umts_function(2-Modem)> open the Bulk-OUT pipe...OK, xfer:0xa7c60a20, buf:0x(null), pipe:0x85dd3200 [ 93.807000] open_umts_function(2-Modem)> NDIS mode, ignore Intr-IN pipe... [ 93.814000] open_umts_function(2-Modem)> Data PDP(1) enable... [ 93.819000] open_umts_function(1-AT)> open the Bulk-IN pipe...OK, xfer:0xa7c61a40, buf:0xa4caa020, pipe:0x85dd32a0 [ 93.856000] open_umts_function(1-AT)> open the Bulk-OUT pipe...OK, xfer:0xa7c62a60, buf:0xa4cae420, pipe:0x85dd3340 [ 93.875000] open_umts_function(Voice)> function disable... [ 93.881000] open_umts_function(0-Diag)> open the Bulk-IN pipe...OK, xfer:0xa7c63a80, buf:0xa4cb2820, pipe:0x85dd33e0 [ 93.908000] open_umts_function(0-Diag)> open the Bulk-OUT pipe...OK, xfer:0xa7c64aa0, buf:0xa4cbb020, pipe:0x85dd3480 [ 93.935000] Run a kernel thread "uumts_tx_DiagBridgeUSBTxTask" success (PID: 7511) (curr nice 0) (kdata 0xC1C28EF8) [ 93.944000] open_umts_function(3-NDIS1)> open the Bulk-IN pipe...uumts_DiagBridgeUSBTxTask: create client socket success. [ 93.955000] uumts_DiagBridgeUSBTxTask: WAIT FOR kernel_accept() ***************************** [ 93.979000] OK, xfer:0xa7ca3260, buf:0x(null), pipe:0x85dd3520 [ 93.984000] open_umts_function(3-NDIS1)> open the Bulk-OUT pipe...OK, xfer:0xa7ca4280, buf:0x(null), pipe:0x85dd35c0 [ 94.008000] open_umts_function(3-NDIS1)> Data PDP(1) enable... [ 94.014000] open_umts_function(4-NDIS2)> open the Bulk-IN pipe...OK, xfer:0xa7ce2a40, buf:0x(null), pipe:0x85dd3660 [ 94.046000] open_umts_function(4-NDIS2)> open the Bulk-OUT pipe...OK, xfer:0xa7ce3a60, buf:0x(null), pipe:0x85dd3700 [ 94.076000] open_umts_function(4-NDIS2)> Voice PDP(2) enable... [ 94.082000] ?[1;32mUSB UMTS Module: Version 3.0.0 build Oct 18 2012 13:40:18 [ 94.082000] ?[0muumts_startup() USB UMTS is attached! [ 94.094000] [USB MEM_COUNT] showUsbMemU() : SmallUnCached, have: 5809 [ 94.100000] [USB MEM_COUNT] showUsbMemU() : MediumUnCached, have: 246 [ 94.107000] [USB MEM_COUNT] showUsbMemU() : LargeUnCached, have: 23 [ 94.113000] [USB MEM_COUNT] showUsbMemC() : SmallCached, have: 290 [ 94.119000] [USB MEM_COUNT] showUsbMemC() : MediumCached, have: 73 [ 94.125000] [USB MEM_COUNT] showUsbMemC() : LargeCached, have: 30 [ 94.132000] ucdc_attach() USB CDC is attached! [ 94.136000] usbd_check_new_device_block(v:0x0408/p:0xea24) depth:1, portno:1, confsNum:1, nifaces:5 [ 94.145000] usbd_check_new_device_block(1) idx:1, iNum:1, Original iClass:ff, isClass:ff, iProto:ff, iFaces:00 [ 94.155000] usbd_vendor_class_translate() Lock port for device type 0x00ff OK !!! [ 94.162000] usbd_check_new_device_block(1) idx:1, iNum:1, iClass:ff, isClass:ff, iProto:ff, iFaces:00 [ 94.172000] usbd_check_new_device_block(1) idx:1, ifStr:[], epCnt:2 [ 94.178000] usbd_check_new_device_block(1)> Interface class 0xff unsupported! [ 94.186000] usbd_probe_and_attach(0-1)> port:1, addr:2, check device blocking failed [ 94.193000] usbd_check_new_device_block(v:0x0408/p:0xea24) depth:1, portno:1, confsNum:1, nifaces:5 [ 94.202000] usbd_check_new_device_block(2) idx:2, iNum:2, Original iClass:ff, isClass:ff, iProto:ff, iFaces:00 [ 94.212000] usbd_vendor_class_translate() Lock port for device type 0x00ff OK !!! [ 94.220000] usbd_check_new_device_block(2) idx:2, iNum:2, iClass:ff, isClass:ff, iProto:ff, iFaces:00 [ 94.229000] usbd_check_new_device_block(2) idx:2, ifStr:[], epCnt:3 [ 94.236000] usbd_check_new_device_block(1)> Interface class 0xff unsupported! [ 94.243000] usbd_probe_and_attach(0-2)> port:1, addr:2, check device blocking failed [ 94.251000] usbd_check_new_device_block(v:0x0408/p:0xea24) depth:1, portno:1, confsNum:1, nifaces:5 [ 94.260000] usbd_check_new_device_block(3) idx:3, iNum:3, Original iClass:ff, isClass:ff, iProto:ff, iFaces:00 [ 94.270000] usbd_vendor_class_translate() Lock port for device type 0x00ff OK !!! [ 94.277000] usbd_check_new_device_block(3) idx:3, iNum:3, iClass:ff, isClass:ff, iProto:ff, iFaces:00 [ 94.286000] usbd_check_new_device_block(3) idx:3, ifStr:[], epCnt:3 [ 94.293000] usbd_check_new_device_block(1)> Interface class 0xff unsupported! [ 94.300000] usbd_probe_and_attach(0-3)> port:1, addr:2, check device blocking failed [ 94.308000] usbd_check_new_device_block(v:0x0408/p:0xea24) depth:1, portno:1, confsNum:1, nifaces:5 [ 94.317000] usbd_check_new_device_block(4) idx:4, iNum:4, Original iClass:ff, isClass:ff, iProto:ff, iFaces:00 [ 94.327000] usbd_vendor_class_translate() Lock port for device type 0x00ff OK !!! [ 94.334000] usbd_check_new_device_block(4) idx:4, iNum:4, iClass:ff, isClass:ff, iProto:ff, iFaces:00 [ 94.344000] usbd_check_new_device_block(4) idx:4, ifStr:[], epCnt:3 [ 94.350000] usbd_check_new_device_block(1)> Interface class 0xff unsupported! [ 94.357000] usbd_probe_and_attach(0-4)> port:1, addr:2, check device blocking failed [ 94.365000] TRACE> isdn_open [ 94.365000] TRACE> isdn_initialize_cmd [ 94.369000] TRACE> isdn_initialize_cmd: Seting up timers, Hz: 1000 [ 94.373000] VMMC_TAPI_LL_ALM_Volume_Set: Tx -2 Rx -9 [ 95.411000] VMMC_TAPI_LL_ALM_Volume_Set: Tx -2 Rx -9 [ 95.755000] uhub_explore(4.5): port 1 change, need check: status(0x0308), change(0x0001)... [ 95.793000] uhub_explore(4.5): port 2 change, need check: status(0x0308), change(0x0001)... [ 96.267000] uhub_explore(4.5): port 1 change, need check: status(0x0308), change(0x0001)... [ 96.387000] uhub_explore(4.5): port 2 change, need check: status(0x0308), change(0x0001)... [ 98.925000] Get concurrent card MAC address:50:7e:5d:50:d9:c250:7e:5d:50:d9:c4 [ 98.931000] Update MAC(0)=50:7e:5d:50:d9:c2 [ 98.935000] Update MAC(1)=50:7e:5d:50:d9:c3 [ 98.939000] Update MAC(0)=50:7e:5d:50:d9:c4 [ 98.943000] Warning! MAC addr not equal to MII master => set MiiMasterMac=50:7e:5d:50:d9:bc [ 98.952000] You've assigned a different MAC. [ 99.033000] uhub_explore(4.5): port 1 change, need check: status(0x0308), change(0x0001)... [ 99.071000] uhub_explore(4.5): port 2 change, need check: status(0x0308), change(0x0001)... [ 99.135000] Run a kernel thread "usb_hc_timer_child_task" success (PID: 7701) (curr nice 0) (kdata 0xC1C28F14) [ 99.144000] umts_para_init_tsk() run-up... [ 99.148000] umts_para_init_tsk() ifno:2, net_ifno:1, sc_idx:0, vid:040804x, pid:0xea24 [ 99.282000] setup MBSS[1] success [ 99.284000] ra1: ==>>> MBSS_VirtualIF_Open [ 99.339000] iNIC Open rai0 [ 99.340000] Op mode = 1 [ 99.343000] rlk_inic_mbss_init ---> [ 99.346000] Register MBSSID IF (rai1) [ 99.361000] rlk_inic_mbss_init <--- [ 99.410000] uhub_explore(4.5): port 1 change, need check: status(0x0308), change(0x0001)... [ 99.448000] uhub_explore(4.5): port 2 change, need check: status(0x0308), change(0x0001)... [ 99.456000] "Enable Rx0 and Rx1" [ 99.458000] sp=0, ep=19, nextc=20 [ 99.510000] setup MBSS[1] success [ 99.512000] rai1: ==>>> MBSS_VirtualIF_Open [ 99.965000] "Auto scan" [ 99.965000] sp=0, ep=10, nextc=11 [ 99.977000] updateSIMSecurityCheck() Security tmpBuf:[ [ 99.977000] *QSECCHECK: "Disable avoid GUTI NAS security check" -- (0) [ 99.977000] [ 99.977000] OK [ 99.977000] ] [ 99.993000] updateSIMSecurityCheck() tkNum = 3 [ 99.997000] updateSIMSecurityCheck() check-point 1 [ 100.002000] updateSIMSecurityCheck() check-point 2 [ 100.006000] "Disable avoid GUTI NAS security check" [ 100.011000] sp=0, ep=38, nextc=39 [ 100.015000] updateSIMSecurityCheck() check-point 3, ret2=1 [ 100.020000] updateSIMSecurityCheck() check-point 4, ret2=2 [ 101.068000] Run a kernel thread "sc0.umtsReceCtrlTsk" success (PID: 7882) (curr nice 0) (kdata 0xC1C28F30) setting 2.4G Main SSID CNT=22, Got UE Firmware Version: 20120706_1KGQCI_4036_M0.07 setting 2.4G Second SSID No isdn phone detected! setting 5G Main SSID setting 5G Second SSID analog phone (1) not detected! [ 103.788000] ********** changeModemState() task 7701 will release 00000080 captured by task[0]:0 analog phone (2) not detected! m_nPhoneClientNum = 0 [ 105.798000] ********** changeModemState() task 7701 will release 00000080 captured by task[0]:0 [ 105.806000] umts_para_init_tsk() LTE module detected OKAY! Thu Oct 18 05:36:10 CEST 2012 firewall.user finished 0

OEM failsafe bootlog

ROM VER: 1.1.4 CFG 06 NAND NAND Read OK ROM VER: 1.1.4 CFG 06 NAND NAND Read OK nand_read_page - 00000008 DDR autotuning Rev 0.3c DDR size from 0xa0000000 - 0xa7ffffff DDR check ok... start booting... U-Boot 2010.06-Lv2.0.40-A0.3 (Jul 12 2012 - 22:00:12) CLOCK CPU 500M RAM 250M DRAM: 128 MiB NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bit) 512 MiB Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 nand_read_bbt: Bad block at 0x00000f6c0000 In: serial Out: serial Err: serial Net: Internal phy(GE) firmware version: 0x040b vr9 Switch Type "run flash_nfs" to mount root filesystem over NFS reset button pressed --> 1 reset button pressed --> 2 reset button pressed --> 3 reset button pressed --> 4 reset button pressed --> 5 enter rescue process ... Uncompressing LCD bootup images ............... NAND read: device 0 offset 0x0000000004700000, size 0x0000000000300000 0x300000 bytes read: OK Using vr9 Switch device TFTP from server 192.168.2.100; our IP address is 192.168.2.1 Filename 'fullimage.img'. Load address: 0x80800000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ##### done Bytes transferred = 24875137 (17b9081 hex) verify firmware validation: loadaddr = 0x80800000, filesize = 24875137 0x814c5040 magic number not found Uncompressing LCD bootup images ............... NAND read: device 0 offset 0x0000000004700000, size 0x0000000000300000 0x300000 bytes read: OK

OpenWrt bootlog

PUT HERE YOUR BOOTLOG

Notes

GPL Code

Here is the download of the GPL code.
Thanks to the guys from gpl-violations.org who helped us much to get hands on it. http://dl.hald.pw/904lte-01.07.tar.gz

Tags

For some Help with the Tags, please have a look here: tags

Back to top

toh/arcadyan/easybox_904_lte.txt · Last modified: 2014/10/12 13:02 by theoradicus