Differences

This shows you the differences between two versions of the page.

toh:arcadyan:vgv7519 [2013/05/19 11:25]
toh:arcadyan:vgv7519 [2014/10/19 00:38] (current)
thelizard Added UART boot method
Line 1: Line 1:
====== Astoria networks VGV7519 ====== ====== Astoria networks VGV7519 ======
-Also known as KPN Experia Box v8+ 
 +There seem to be ARV7519KW (aka KPN Experia Box v8).
===== Supported Versions ===== ===== Supported Versions =====
^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^ ^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^
-| v1  |  ?  | J229112404 | ? | KPN Experia Box V8 |+| v1  |  ?  | J229112404 | [[https://dev.openwrt.org/changeset/38266/trunk|r38266]] | KPN Experia Box V8 |
**NOTE:** Anything not included in model specific notes, or where a short comment couldn't be included on the [[#notes]]. **NOTE:** Anything not included in model specific notes, or where a short comment couldn't be included on the [[#notes]].
Line 24: Line 25:
  - -> [[doc:howto:generic.flashing|Install OpenWrt]]   - -> [[doc:howto:generic.flashing|Install OpenWrt]]
-==== Flash Layout ==== +Note that the only working method is using JTAG! 
-Please check out the article [[doc:techref:Flash Layout]]. It contains an example and a couple of explanations. + 
-Raw flash, 2 x EN29LV640AB-90TIP+The best approach for migration to OpenWRT is as follows: 
 +  * Open your device 
 +  * Connect JTAG 
 +  * Backup original flash image 
 +  * Download U-BOOT ram image: [[https://github.com/openwrt-vgv7519/uboot-bin/blob/master/ram/u-boot.bin]] 
 +  * Download U_BOOT flash image: [[https://github.com/openwrt-vgv7519/uboot-bin/blob/master/flash/u-boot.bin]] 
 +  * Use JTAG to start ram image of u-boot 
 +  * Download and flash image to the device using tftp 
 + 
 +  * Download openwrt source tree and build images for VGV-7519 with squashfs image. 
 +  * Flash the squashfs image using tftp 
 + 
 + 
 +==== Original Flash Layout ==== 
 + 
 +This is the Flash layout as logged by the original VR9 Bootloader 
 + 
 +^ # ^Area          ^Address  ^  Length^ 
 +|[0]|Boot          |0xB0000000|    256K| 
 +|[1]|Boot Params    |0xB0040000|    64K| 
 +|[2]|Certificate    |0xB0050000|    64K| 
 +|[3]|Special Area  |0xB0060000|    64K| 
 +|[4]|Reserve 0      |0xB0070000|    64K| 
 +|[5]|Code Image 0  |0xB0080000|  7680K| 
 +|[6]|Primary Setting|0xB4000000|    64K| 
 +|[7]|Configuration  |0xB4010000|    384K| 
 +|[8]|Reserve 1      |0xB4070000|    64K| 
 +|[9]|Code Image 1  |0xB4080000|  7680K| 
 +|[10]|1st Flash    |0xB0000000|  8192K| 
 +|[11]|2nd Flash    |0xB4000000|  8192K| 
 + 
 +==== OpenWRT Flash Layout ====
-On my device, both flashes contain the same contents...+^  Arcadyan VGV7519 Flash Layout          ^^^^^^^^ 
 +^ Layer0      |                      EN29LV640AB-90TIP  8192KiB                                                                      |||||  EN29LV640AB-90TIP 8192KiB  || 
 +^ Layer1      |  mtd0 **//u-boot//** |  reserved  |  **//u-boot-env//**  |  reserved  |  mtd5 **//firmware//** 15872KiB                                      |||| 
 +^ Layer2      |                              ||||  mtd1 **//kernel//** 1984KiB  |  mtd2 **//rootfs//** 13888KiB                          || 
 +^ <color magenta>mountpoint</color>  |      ||||                              |  <color magenta>''/''</color>                          || 
 +^ filesystem  |                              ||||                              |  [[doc:techref:filesystems#mini_fo|mini_fo]]/[[doc:techref:filesystems#overlayfs|overlayfs]]          || 
 +^ Layer3      |                              ||||                              |                |  mtd3 **//rootfs_data//** 11904KiB    | 
 +^ Size in KiB  |  256KiB  |  128KiB  |  64KiB  |  64KiB  |                      1984KiB                      |  1984KiB        |  11904KiB    | 
 +^ Name        |  **//u-boot//**              |  //none//  | **//u-boot env//** |  //none//  |  **//kernel//**              |                |  **//rootfs_data//**            | 
 +^ <color magenta>mountpoint</color>          |  //none//  |  //none//  |  //none//  |  //none//  |  //none//                    |  <color magenta>''/rom''</color>  |  <color magenta>''/overlay''</color>  | 
 +^ filesystem  |    //none//                  |  //none//  |  //none//  |  //none//  |  //none//  |  [[doc:techref:filesystems#SquashFS]]      ||
==== OEM easy installation ==== ==== OEM easy installation ====
 +The easiest way is to enter the recovery mode as described in [[doc/techref/bootloader/brnboot]]
 +Instead on what is documented on that page, for this model the recovery web interface is available on http://192.168.2.254/
-| FIXME The instructions below are for Broadcom devices and only serve as an example. Don't leave them in place if they do not apply to a particular device! |+<color red>Additionally the page request for a PIN code which is still unknown... 
 +This PIN-code is also SHA-1 hashed and compared, I have no idea about constraints, the hash as taken from the disassembly is: 
 +B16D0EF3 DD0632DC D13D135E 02A097AE C4044C24</color>
-This section deals with how you install OpenWrt from a device freshly opened.  Plus the steps required such as reset to factory defaults if the device has already been configured+The bootloader's serial console is another option, but there is a SHA-1 hashed password as well. 
 +There are 2 ways to flash it, use UART BOOT mod or JTAG...
-**Note:** Reset router to factory defaults if it has been previously configured. +I have managed to patch the password protection code sequence out, so I am able to gain access to the bootloader menu
-  *Browse to http://192.168.1.1/Upgrade.asp +The loader itself won't let you erase or overwrite the first sectors so it is useless for flashing another bootloader.
- *Upload .bin file to router +
-  *Wait for it to reboot +
-  *Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.+
-==== OEM installation using the TFTP method ====+Administrator mode is aquired by pressing '!' 
 +Sniffing around through the bootloader disassembly shows some differences, these are explained in the last column
-->  [[doc:howto:generic.flashing.tftp]]+The VR9 bootloader has the following menu options:
-=== Specific values you need ===+|    | Menu item | Admin mode? | comments |  
 +| [#] | Set Serial Number | | | 
 +| [2] | Use Normal Firmware | | not implemented | 
 +| [3] | Use ART-Testing Firmware | | not implemented | 
 +| [9] | Taggle ART Firmware Enable/Disable | | | 
 +| [A] | Set MAC Address | | | 
 +| [B] | Set WPA Key | | | 
 +| [E] | Erase Flash | | | 
 +| [G] | Run Runtime Code | | | 
 +| [H] | Set Options | | | 
 +| [I] | Unlisted | | Doesn't show menu, guess it is patched out | 
 +| [L] | Unlisted | | Doesn't show menu, guess it is patched out | 
 +| [M] | Upload to Memory | X | | 
 +| [P] | Print Boot Params | | | 
 +| [R] | Read from Memory | X | | 
 +| [S] | Unlisted | | Doesn't show menu, guess it is patched out | 
 +| [T] | Test Memory (not listed as option) | | Found in disassembly | 
 +| [U] | Upload to Flash | | | 
 +| [V] | Set Board Version | | | 
 +| [W] | Write to Memory | X | | 
 +| [Y] | Go to Memory | X | | 
 +| [Z] | Dump DDR Ram Register | X | | 
 +| [0] | Primary = Image 0 | X | | 
 +| [1] | Primary = Image 1 | X | | 
 + 
 +==== UART method ==== 
 + 
 +The installation procedure in short: 
 +  - Short the bootsel_0 pins (R159), apply VCC (3V3) to the R155 side of R154 (bootsel_2) and power on the router. 
 +  - Upload a special U-Boot RAM image using a serial cable 
 +  - Use U-Boot to erase the flash and install U-Boot to flash 
 +  - Power off the router, unshort the bootsel_0 pins, remove VCC from R154 and power on again 
 +  - Use the installed U-Boot to install OpenWrt to flash 
 + 
 +=== Preparation === 
 + 
 +You need a RS232-to-TTL cable connected to the serial header shown in the picture below. Short the UART boot pins with two jumper caps. 
 + 
 +{{:media:vgv7519_bootsel.jpg|}} 
 +(NOTE: bootsel_4 and bootsel_1 are just in the image for reference) 
 + 
 +Start TFTP server on your computer and copy ''openwrt-lantiq-vgv7519_nor-u-boot.img'' and ''openwrt-lantiq-xway-VGV7519-squashfs.image'' to the TFTP server root. Connect your computer to the router with an ethernet cable and configure the IP address to 192.168.1.2, netmask 255.255.255.0. 
 + 
 +=== Loading U-Boot === 
 + 
 +Use 115200 bps, 8-N-1, no flow control, as the serial connection parameter. 
 + 
 +Power on the router. You should see 
 +<code> 
 +ROM VER: 1.0.5 
 +CFG 04 
 +UART 
 +</code> 
 +on the serial output. 
 + 
 +Send ''openwrt-lantiq-arv7510pw_ram-u-boot.asc'' as raw ascii to the router. U-Boot should start. Press any key to stop autoboot. At this point you can make a backup of the original firmware using ''md.l 0xb0000000 0x1000000'' and logging the output (takes roughly 2 hours). The flash can be erased by issuing first ''protect off all'' and then ''erase all''. Use first ''setenv ipaddr 192.168.1.1'', ''setenv serverip 192.168.1.2'' and ''setenv ethaddr xx:xx:xx:xx:xx:xx'' (ethernet address can be found from the sticker on top of the switch ports) to configure the network, and then ''tftp 0x80700000 openwrt-lantiq-arv7510pw_nor-u-boot.img'' to transfer the actual U-Boot image to memory. Write it to flash using ''cp.b 0x80700000 0xb0000000 ${filesize}''. Power off the router and remove the jumper caps from UART boot pins. 
 + 
 +=== Loading OpenWrt === 
 + 
 +Power on the router. The U-Boot installed in the previous step should start. Press any key to stop autoboot. Use again ''setenv ipaddr 192.168.1.1'', ''setenv serverip 192.168.1.2'' and ''setenv ethaddr xx:xx:xx:xx:xx:xx'' to configure the network. Use ''saveenv'' to save these to flash. Use ''tftp 0x80700000 openwrt-lantiq-xway-VGV7519-squashfs.image'' to transfer the actual OpenWRT image to memory. Write it to flash using ''cp.b 0x80700000 0xb0060000 ${filesize}''. Use ''reset'' to reset the board. Watch as U-Boot loads OpenWrt and proceed to configure it to your liking!
-| Bootloader tftp server IPv4 address | FILL-IN | 
-| Bootloader MAC address (special) | FILL-IN | 
-| Firmware tftp image | [[http://downloads.openwrt.org/FILL-IN/openwrt-FILL-IN-generic-FILL-IN-squashfs-tftp.bin]] (**''NOTE:''** Name must contain //"tftp"//) | 
-| TFTP Transfer Window | FILL-IN seconds | 
-| TFTP Window Start | approximately FILL-IN seconds after power on | 
-| TFTP Client Required IP Address | FILL-IN | 
==== Upgrading OpenWrt ==== ==== Upgrading OpenWrt ====
->  [[doc:howto:generic.sysupgrade]] ->  [[doc:howto:generic.sysupgrade]]
 +
 +FIXME - haven't installed OpenWRT yet, so no updated instructions
If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
Line 115: Line 215:
-> [[doc:howto:hardware.button]] on howto use and configure the hardware button(s). -> [[doc:howto:hardware.button]] on howto use and configure the hardware button(s).
-The Linksys WRT54GL has two buttons. They are Reset and Secure Easy Setup. Here, we merely name the buttons, so we can use them in the above Howto: +The Arcadyan VGV7519 has four buttons. They are Reset, Secure Easy Setup, WDS and Wifi enable. Here, we merely name the buttons, so we can use them in the above Howto: 
-^ BUTTON ^ Event ^ Location ^ +^ BUTTON ^ Event ^ Location ^ Action
-| Reset | reset | back | +| Reset | reset | back |
-| Secure Easy Setup | ses | side | +| ECO | ? | side | disables USB & WIFI
-| WDS | ? | side | +| Wifi enable | rfkill | side |
-| Wifi enable | ? | side |+| wps | wps | side | |
Line 127: Line 227:
| **[[wp>Instruction set|Architecture]]:**    | [[wp>MIPS architecture|MIPS]] | | **[[wp>Instruction set|Architecture]]:**    | [[wp>MIPS architecture|MIPS]] |
| **Vendor:**          | [[wp>Lantiq]] | | **Vendor:**          | [[wp>Lantiq]] |
-| **[[doc:techref:Bootloader]]:**    | [[doc:techref:bootloader:uboot|U-Boot]] / [[doc:techref:bootloader:RedBoot]] / ... |+| **[[doc:techref:Bootloader]]:**    | [[doc:techref:bootloader:brnboot|BRNBoot]] |
| **[[doc:hardware:soc|System-On-Chip]]:**  | VRX288 V1.1 (MIPS, PSB 80920 EL) | | **[[doc:hardware:soc|System-On-Chip]]:**  | VRX288 V1.1 (MIPS, PSB 80920 EL) |
-| **[[doc:hardware:cpu|CPU]]/Speed**        | 24Kc V7.4 500 Mhz |+| **[[doc:hardware:cpu|CPU]]/Speed**        | 34Kc 500 Mhz |
| **Flash-Chip:**      | [[http://www.eonssi.com/upfile/p2010610151847.pdf|EN29LV640AB-90TIP]] | | **Flash-Chip:**      | [[http://www.eonssi.com/upfile/p2010610151847.pdf|EN29LV640AB-90TIP]] |
| **Flash size:**      | 2x 8192 MiB | | **Flash size:**      | 2x 8192 MiB |
Line 135: Line 235:
| **WAN:**            | 1x RJ45 | | **WAN:**            | 1x RJ45 |
| **Modem:**          | Infineon/Lantiq [[http://www.lantiq.com/uploads/tx_abzlantiqproducts/PB-e-0027-v2_lres.pdf|XWAY VRX208]]<html><br>VDSL2 (G.993.2),<br>VDSL1 (G.993.1, T1.424, TS 101 270),<br>ADSL1/2/2+ (G.992.1/3/5) Annexes A, B, I, J, M, L</html> | | **Modem:**          | Infineon/Lantiq [[http://www.lantiq.com/uploads/tx_abzlantiqproducts/PB-e-0027-v2_lres.pdf|XWAY VRX208]]<html><br>VDSL2 (G.993.2),<br>VDSL1 (G.993.1, T1.424, TS 101 270),<br>ADSL1/2/2+ (G.992.1/3/5) Annexes A, B, I, J, M, L</html> |
-| **Wireless:**        | (unknown for now) Atheros AR9103 2.4ghz 802.11bgn | +| **Wireless:**        | RALink RT5362F TPHR059609 1222STA1 2.4ghz 802.11bgn | 
-| **Ethernet:**        | (unknown for now) RealTek RTL8366RB Gigabit w/ vlan support [[doc:techref:swconfig]] |+| **Ethernet:**        | <del>(unknown for now) RealTek RTL8366RB Gigabit w/ vlan support [[doc:techref:swconfig]]</del> Internal configurable (Infineon) (3x lantiq PEF7071v) |
| **Internet:**        | ADSL2+  | | **Internet:**        | ADSL2+  |
-| **Phone:** | [[http://www.lantiq.com/products/voice-customer-premises-equipment/slictm/xwaytm-slic100/xwaytm-slic120/|Lantiq XWAY SLIC120 (PEF 42068 V V1.2)]], 3x FXS (TAE ports which provide POTS via a SIP gateway) |+| **Phone:** | [[http://www.lantiq.com/products/voice-customer-premises-equipment/slictm/xwaytm-slic100/xwaytm-slic120/|Lantiq XWAY SLIC120 (PEF 42068 V V1.2)]], 3x FXS (TAE ports which provide POTS via a SIP gateway) Si3050/Si3011fs |
| **USB:**            | Yes 2 x 2.0    | | **USB:**            | Yes 2 x 2.0    |
| **[[doc:hardware:port.serial|Serial]]:**          | [[#Serial|Yes]] | | **[[doc:hardware:port.serial|Serial]]:**          | [[#Serial|Yes]] |
Line 148: Line 248:
//Front:// //Front://
-{{:media:toh:arcadyan:vgv7519:vgv7519_front.jpg|}}+{{:media:toh:arcadyan:vgv7519:vgv7519_front.jpg?400|}}
//Back:// //Back://
-{{:media:toh:arcadyan:vgv7519:vgv7519_back.jpg|}} +{{:media:toh:arcadyan:vgv7519:vgv7519_back.jpg?400|}} 
-{{:media:toh:arcadyan:vgv7519:vgv7519_back_connectors.jpg|}} + 
-{{:media:toh:arcadyan:vgv7519:vgv7519_back_label.jpg|}}+{{:media:toh:arcadyan:vgv7519:vgv7519_back_connectors.jpg?400|}} 
 + 
 +{{:media:toh:arcadyan:vgv7519:vgv7519_back_label.jpg?400|}} 
* Note that in this pictures the casing was placed on top of the PCB, not fitting the connectors (as the jtag cables were still attached) * Note that in this pictures the casing was placed on top of the PCB, not fitting the connectors (as the jtag cables were still attached)
Line 166: Line 269:
//Main PCB// //Main PCB//
-{{:media:toh:arcadyan:vgv7519:vgv7519_pcb_front.jpg|}}+{{:media:toh:arcadyan:vgv7519:vgv7519_pcb_front.jpg?400|}}
I had to solder the 14 pins EJTAG header, but the location is quite clear I had to solder the 14 pins EJTAG header, but the location is quite clear
-{{:media:toh:arcadyan:vgv7519:vgv7519_pcb_front_headers.jpg|}}+ 
 +{{:media:toh:arcadyan:vgv7519:vgv7519_pcb_front_headers.jpg?400|}} 
EJTAG header and serial port header (4pins), 1st pin is at the right side (Pin 1 marking is located at the other side of the pin) EJTAG header and serial port header (4pins), 1st pin is at the right side (Pin 1 marking is located at the other side of the pin)
-{{:media:toh:arcadyan:vgv7519:vgv7519_pcb_back.jpg|}}+ 
 +{{:media:toh:arcadyan:vgv7519:vgv7519_pcb_back.jpg?400|}} 
 + 
 +Both flash chips are located at the bottom of the PCB 
 + 
 +==== Important components ==== 
 +The actual VRX288 version is important because of the internal ethernet PHY firmware, mine is a V1.1 
 + 
 +{{:media:toh:arcadyan:vgv7519:vgv7519_vrx288_v1_1.jpg?400|}} 
 + 
 + 
 +There are 3 external ethernet PHY chips available (these are V1.3) 
 + 
 +{{:media:toh:arcadyan:vgv7519:vgv7519_ethernet_phy.jpg?400|}} 
==== Serial ==== ==== Serial ====
Line 180: Line 299:
| **Function** |  GND  |  RX  |  TX  |  VCC (3.3V)  | | **Function** |  GND  |  RX  |  TX  |  VCC (3.3V)  |
-<color red>Hooking up to the serial with 115200/8N1 enables you to access the bootloader. You have to enter three spaces immediately after powerup after which you have to enter some secret password (seems to be 16 characters, but of course I have no idea what it would be...</color>+<color red>Hooking up to the serial with 115200/8N1 enables you to access the bootloader. You have to enter three spaces immediately after powerup after which you have to enter some secret password (seems to be 16 characters, but of course I have no idea what it would be... The SHA-1 hash for the password is:  
 +42f25cd06c3e1d7096b35cbd3c3813c23adaf03a</color>
For a photo see the second picture from the Main PCB section For a photo see the second picture from the Main PCB section
 +
 +==== GPIOs ====
 +
 +Generic VR9 gpio map (0xBE100B00+x):
 +|        |OUT    |IN      |DIR    |ALT0    |ALT1    |OD      |PUDSEL  |PUDEN |
 +|port0  |10      |14      |18      |1c      |20      |24      |2c      |30    |
 +|port1  |40      |44      |48      |4c      |50      |54      |5c      |60    |
 +|port2  |70      |74      |78      |7c      |80      |84      |8c      |90    |
 +|port3  |a0      |a4      |a8      |ac      |b0-53  |b4-34  |bc-38  |c0-3c |
 +
 +Generic pin id to bit:
 +|0      |1      |2      |3      |4      |5      |6      7      8      9      10      11      12      13      14      15
 +|0x1    |0x2    |0x4    |0x8    |0x10    |0x20    |0x40    0x80    0x100  0x200  0x400  0x800  0x1000  0x2000  0x4000  0x8000
 +
 +
 +Generic alternat to function:
 +|        |f0      |f1      |f2      |f3  |
 +|alt0    |0      |1      |0      |1    |
 +|alt1    |0      |0      |1      |1    |
 +
 +Function from disassembled 2.x firmware
 +|gpio03|???                              |      | od | dir|~alt0|~alt1            |gpio| 
 +|gpio04|stp                              |      | od | dir| alt0|~alt1            |stp | 
 +|gpio05|stp                              |      | od | dir| alt0|~alt1            |stp | 
 +|gpio06|stp                              |      | od | dir| alt0|~alt1            |stp | 
 +|gpio11|duslic(FXS)                      |      | od | dir|~alt0|~alt1            |gpio| 
 +|gpio12|CoC /USB HCD                    | out  | od | dir|~alt0|~alt1            |gpio| 
 +|gpio15|ProDAAInitialize(fxo)            |      |    |    |    |                  |    |
 +|gpio20|sip_core_mwi_led_off            |      |    |    |    |                  |    | 
 +|gpio21|pci                              |~out  | od | dir|~alt0|~alt1            |gpio| 
 +|gpio30|vmmc-relay                      | out  | od | dir|~alt0|~alt1            |gpio| 
 +|gpio32|hcd                              |      | od | dir|~alt0|~alt1            |gpio| 
 +|gpio37|reinjiection maybe voip related  |      |    |    |    |                  |    | 
 +|gpio42|mdio                            |      | od | dir| alt0|~alt1            |mdio| 
 +|gpio43|mdio                            |      | od | dir| alt0|~alt1            |mdio| 
 +|gpio47|???                              | out  | od | dir|~alt0|~alt1            |gpio| 
 +
 +-Eth led                                     
 +|gpio07 GPHY                            |      | od | dir| alt0| alt1            |gphy|
 +|gpio44 GPHY                            |      | od | dir| alt0| alt1            |gphy|
 +
 +-buttons
 +|gpio09|btn-rst                          | in    |    |~dir|~alt0|~alt1            |gpio|
 +|gpio10|btn-wps                          | in    |    |~dir|~alt0|~alt1            |gpio|
 +|gpio41|btn-echo                        | in    |    |~dir|~alt0|~alt1            |gpio| 
 +|gpio45|btn-wlan                        | in    |    |~dir|~alt0|~alt1            |gpio| 
==== JTAG ==== ==== JTAG ====
Line 203: Line 369:
===== Bootloader Mods ===== ===== Bootloader Mods =====
  - you could read about [[doc:techref:bootloader]] in general   - you could read about [[doc:techref:bootloader]] in general
 +
 +I have patched out the password protection to gain access to the bootloader's menu, There aren't really interesting things to do there, so I flashed it over with u-boot.
===== Hardware mods ===== ===== Hardware mods =====
  - as a beginner, you really should inform yourself about [[doc:hardware:soldering]] in general and then obtain some practical experience!   - as a beginner, you really should inform yourself about [[doc:hardware:soldering]] in general and then obtain some practical experience!
-==== 128MiB RAM Mod ==== +I had to solder the JTAG header on the board
-==== I²C GPIO Mod ==== +
-==== I²C Tiny-USB Mod ====+
===== Bootlogs ===== ===== Bootlogs =====
Line 217: Line 383:
<code> <code>
-ROM VER: 1î 
ROM VER: 1.0.5 ROM VER: 1.0.5
CFG 01 CFG 01
Line 231: Line 396:
In c_entry() function ... In c_entry() function ...
install_exception install_exception
 +
 +
 +Had to go a long way to retrieve the reset of this (crashing) bootlog
 +
 +[GPIO FLOW] SetGpio() Begin ..
 +[GPIO FLOW] SetGpio() End.
 +Runtime code version: 03.00.122
 +System startup...
 +Set flash memory layout to Boot Parameters found !!!
 +Bootcode version: v3.00.06
 +Serial number: J229112404
 +Hardware version: 01
 +06.07.2012-17:48:38
 +config_fnd=3, cfg_size=31115
 +cgi info size=31055, 0x55545352
 +Decompression ratio = 9.4
 +Signature matched at offset 279224
 +Add-on new config tail> oldSize:279264, oldCfgSize:13625, adjust length to -1
 +[CONFIG] read_config_from_flash ret=0
 +[CONFIG] load_config ret=1
 +cert_one:
 +-----BEGIN CERTIFICATE-----
 +MIIEnDCCBAWgAwIBAgIQdTN9mrDhIzuuLX3kRpFi1DANBgkqhkiG9w0BAQUFADBf
 +MQswCQYDVQQGEwJVUzEXMBUGA1UEChMOVmVyaVNpZ24sIEluYy4xNzA1BgNVBAsT
 +LkNsYXNzIDMgUHVibGljIFByaW1hcnkgQ2VydGlmaWNhdGlvbiBBdXRob3JpdHkw
 +HhcNMDUwMTE5MDAwMDAwWhcNMTUwMTE4MjM1OTU5WjCBsDELMAkGA1UEBhMCVVMx
 +FzAVBgNVBAoTDlZlcmlTaWduLCBJbmMuMR8wHQYDVQQLExZWZXJpU2lnbiBUcnVz
 +dCBOZXR3b3JrMTswOQYDVQQLEzJUZXJtcyBvZiB1c2UgYXQgaHR0cHM6Ly93d3cu
 +dmVyaXNpZ24uY29tL3JwYSAoYykwNTEqMCgGA1UEAxMhVmVyaVNpZ24gQ2xhc3Mg
 +MyBTZWN1cmUgU2VydmVyIENBMIIBIjANBgkqhkiG9w0BAQEFAAOCAQ8AMIIBCgKC
 +AQEAlcMhEo5AxQ0BX3ZeZpTZcyxYGSK4yfx6OZAqd3J8HT732FXjr0LLhzAC3Fus
 +cOa4RLQrNeuT0hcFfstG1lxToDJRnXRkWPkMmgDqXkRJZHL0zRDihQr5NO6ziGap
 +paRa0A6Yf1gNK1K7hql+LvqySHyN2y1fAXWijQY7i7RhB8m+Ipn4G9G1V2YETTX0
 +kXGWtZkIJZuXyDrzILHdnpgMSmO3ps6wAc74k2rzDG6fsemEe4GYQeaB3D0s57Rr
 +4578CBbXs9W5ZhKZfG1xyE2+xw/j+zet1XWHIWuG0EQUWlR5OZZpVsm5Mc2JYVjh
 +2XYFBa33uQKvp/1HkaIiNFox0QIDAQABo4IBgTCCAX0wEgYDVR0TAQH/BAgwBgEB
 +/wIBADBEBgNVHSAEPTA7MDkGC2CGSAGG+EUBBxcDMCowKAYIKwYBBQUHAgEWHGh0
 +dHBzOi8vd3d3LnZlcmlzaWduLmNvbS9ycGEwMQYDVR0fBCowKDAmoCSgIoYgaHR0
 +cDovL2NybC52ZXJpc2lnbi5jb20vcGNhMy5jcmwwDgYDVR0PAQH/BAQDAgEGMBEG
 +CWCGSAGG+EIBAQQEAwIBBjApBgNVHREEIjAgpB4wHDEaMBgGA1UEAxMRQ2xhc3Mz
 +Q0EyMDQ4LTEtNDUwHQYDVR0OBBYEFG/sr6DdiqTv9SoQZy0/VYK81+8lMIGABgNV
 +HSMEeTB3oWOkYTBfMQswCQYDVQQGEwJVUzEXMBUGA1UEChMOVmVyaVNpZ24sIElu
 +Yy4xNzA1BgNVBAsTLkNsYXNzIDMgUHVibGljIFByaW1hcnkgQ2VydGlmaWNhdGlv
 +biBBdXRob3JpdHmCEHC65B0Q2Sk0tjjKewPMur8wDQYJKoZIhvcNAQEFBQADgYEA
 +w34IRl2RNs9n3Nenr6+4IsOLBHTTsWC85v63RBKBWzFzFGNWxnIu0RoDQ1w4ClBK
 +Tc3athmo9JkNr+P32PF1KGX2av6b9L1S2T/L2hbLpZ4ujmZSeD0m+v6UNohKlV4q
 +TBnvbvqCPy0D79YoszcYz0KyNCFkR9MgazpM3OYDkAw=
 +-----END CERTIFICATE-----
 +default route: 0.0.0.0
 +[CheckUSBBackConf]Erase the garbage config in usbBackConf_s
 +BufferInit:
 +BUF_HDR_SZ=192 BUF_ALIGN_SZ=16 BUFFER_OFFSET=448
 +BUF_BUFSZ0=576 BUF_BUFSZ1=4352
 +NUM_OF_B0=0 NUM_OF_B1=2400
 +BUF_POOL0_SZ=0 BUF_POOL1_SZ=10905600
 +sizeof(BUFFER0)=768,sizeof(BUFFER1)=4544
 +*BUF0=0x828e681c *BUF1=0x81e7fffc
 +Altgn *BUF0=0x828e6820 *BUF1=0x81e80000
 +End at BUF0:0x828e6820, BUF1:0x828e6800
 +
 +BUF0[0]=0x828e6820 BUF1[0]=0x81e80000
 +
 +buffer0 pointer init OK!
 +buffer1 pointer init OK!
 +[qm_lnk_init] CLOCKHZ=1000 ...
 +[qm_lnk_init] add if 3 into QM link 0
 +[qm_lnk_init] add if 4 into QM link 0
 +[qm_cbq_enable] no QM attached
 +[qm_cbq_detach] no QM is attached at link 0
 +ptime=2000000/1000, cptime=20202/1000, offtime=40724/1000
 +New cls: id=0, bw=8 ns/byte, maxd=0 ms,
 +        maxb=32, minb=2, avgpktsz=250, maxpktsz=1600,
 +        offtime=1, parent=0, borrow=0
 +        pri=0, maxidle=1, minidle=-25,
 +        maxq=96, clsfg=17
 +ptime=12800000/1000, cptime=1280129299/1000, offtime=1280129299/1000
 +New cls: id=1, bw=808 ns/byte, maxd=0 ms,
 +        maxb=16, minb=1, avgpktsz=1600, maxpktsz=1600,
 +        offtime=1280, parent=8121049c, borrow=8121049c
 +        pri=5, maxidle=341, minidle=-2585,
 +        maxq=48, clsfg=21
 +qm_cbq_attach(): cbqp->cbq_res=107
 +ptime=2000000/1000, cptime=40608/1000, offtime=166340/1000
 +New cls: id=2, bw=8 ns/byte, maxd=0 ms,
 +        maxb=32, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=1, parent=8121049c, borrow=8121049c
 +        pri=5, maxidle=1, minidle=-26,
 +        maxq=48, clsfg=21
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=3, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=6, maxidle=0, minidle=-2560000,
 +        maxq=48, clsfg=20
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=4, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=0, maxidle=0, minidle=-2560000,
 +        maxq=96, clsfg=21
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=5, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=1, maxidle=0, minidle=-2560000,
 +        maxq=48, clsfg=23
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=6, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=2, maxidle=0, minidle=-2560000,
 +        maxq=48, clsfg=23
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=7, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=3, maxidle=0, minidle=-2560000,
 +        maxq=48, clsfg=23
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=8, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=4, maxidle=0, minidle=-2560000,
 +        maxq=48, clsfg=23
 +ptime=2000000/1000, cptime=40608/1000, offtime=166340/1000
 +New cls: id=9, bw=8 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=1, parent=8120ee9c, borrow=8120ee9c
 +        pri=6, maxidle=1, minidle=-26,
 +        maxq=48, clsfg=20
 +gConfig.Interface[0].IP_Addr = 127.0.0.1
 +gConfig.Interface[0].Subnet_Mask = 255.255.255.255
 +gConfig.Interface[0].Description = LOCAL_LOOPBACK
 +***** [iput_IpLinkUp] ifno=0, link_type:12
 +Interface 0 ip = 127.0.0.1
 +
 +gConfig.Interface[1].IP_Addr = 192.168.1.254
 +gConfig.Interface[1].Subnet_Mask = 255.255.255.0
 +gConfig.Interface[1].Description = LAN
 +gConfig.Interface[1].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[1].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[1].VLAN_Idx].IGMP_Querier_Enable = 1
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:01 to VLAN 0 (port 1)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:01 to VLAN 0 (port 2)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:02 to VLAN 0 (port 1)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:02 to VLAN 0 (port 2)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:16 to VLAN 0 (port 1)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:16 to VLAN 0 (port 2)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:7F:FF:FA to VLAN 0 (port 1)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:7F:FF:FA to VLAN 0 (port 2)
 +[mac_0_init] ifno=1, vlan=0, vid=1, port_mask=0xf, mac_0_initialized=0
 +[init_local_variables] ethwan=2, g_eth_wan_mode=3, wanitf=0xffffffff
 +[init_local_variables] g_wan_itf=0x2, g_ipv6_acc_en=1, g_wanqos_en=8
 +[e5 alloc_dma] pre_alloc_desc_total_num=736, line 4437
 +[config_SW_VLAN] bTaggedIngress=0, bTaggedEgress=0
 +mac_0_init: interface 1 registered to VLAN 1, port_mask=f
 +MAC Address(ifno 1): 1c:c6:3c:c4:3d:a7
 +***** [iput_IpLinkUp] ifno=1, link_type:12
 +Interface 1 ip = 192.168.1.254
 +
 +gConfig.Interface[2].IP_Addr = 0.0.0.0
 +gConfig.Interface[2].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[2].Description = WLAN
 +gConfig.Interface[2].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[2].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[2].VLAN_Idx].IGMP_Querier_Enable = 1
 +[HWLAN] ifno=2 irno=7 port=0x00000000
 +***** [iput_IpLinkUp] ifno=2, link_type:12
 +Interface 2 ip = 192.168.1.254
 +
 +gConfig.Interface[3].IP_Addr = 0.0.0.0
 +gConfig.Interface[3].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[3].Description = THS
 +[mac_0_init] ifno=3, vlan=1, vid=2, port_mask=0x10, mac_0_initialized=1
 +[config_SW_VLAN] bTaggedIngress=1, bTaggedEgress=1
 +mac_0_init: interface 3 registered to VLAN 2, port_mask=10
 +MAC Address(ifno 3): 1c:c6:3c:c4:3d:a7
 +***** [iput_IpLinkUp] ifno=3, link_type:2
 +time = 08/01/2003, 00:00:00
 +iput_IpLinkUp(ifno=3)> ifp->add_default_route:1
 +Init NAT data structure
 +iput_IpLinkUp(ifno=3): set ddns_update to 1
 +Interface 3 ip = 0.0.0.0
 +
 +gConfig.Interface[4].IP_Addr = 0.0.0.0
 +gConfig.Interface[4].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[4].Description = ATM2
 +[mac_0_init] ifno=4, vlan=1, vid=2, port_mask=0x10, mac_0_initialized=1
 +[config_SW_VLAN] bTaggedIngress=1, bTaggedEgress=1
 +mac_0_init: interface 4 registered to VLAN 2, port_mask=10
 +MAC Address(ifno 4): 1c:c6:3c:c4:3d:a7
 +***** [iput_IpLinkUp] ifno=4, link_type:2
 +iput_IpLinkUp(ifno=4)> ifp->add_default_route:0
 +Init NAT data structure
 +No default route, no need to reinit the NAT data structure
 +Interface 4 ip = 0.0.0.0
 +
 +gConfig.Interface[15].IP_Addr = 0.0.0.0
 +gConfig.Interface[15].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[15].Description = PPPoE1
 +IFLNK_PPPOE init : (Linkp)ifno = 15 idx = 2
 +IFLNK_PPPOE init : (Driverp)ifno = 15 idx = 4
 +pppInit> set (PPPShutdownRequest[15] = 0), do_connect_in_progress[15]=0
 +[change_phase] start to release the allocated memory in if_table[0].ppp_p->state
 +[pppoe_init]
 +Interface 15 ip = 0.0.0.0
 +
 +gConfig.Interface[16].IP_Addr = 0.0.0.0
 +gConfig.Interface[16].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[16].Description = PPPoE2
 +IFLNK_PPPOE init : (Linkp)ifno = 16 idx = 2
 +IFLNK_PPPOE init : (Driverp)ifno = 16 idx = 4
 +pppInit> set (PPPShutdownRequest[16] = 0), do_connect_in_progress[16]=0
 +[change_phase] start to release the allocated memory in if_table[0].ppp_p->state
 +[pppoe_init]
 +[PPPoE]gInitOk==1 , So Not Do pppoe_init
 +Interface 16 ip = 0.0.0.0
 +
 +gConfig.Interface[31].IP_Addr = 0.0.0.0
 +gConfig.Interface[31].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[31].Description = WDS1
 +gConfig.Interface[31].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[31].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[31].VLAN_Idx].IGMP_Querier_Enable = 1
 +[HWLAN] ifno=31 irno=7 port=0x00000000
 +***** [iput_IpLinkUp] ifno=31, link_type:12
 +Interface 31 ip = 192.168.1.254
 +
 +gConfig.Interface[32].IP_Addr = 0.0.0.0
 +gConfig.Interface[32].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[32].Description = WDS2
 +gConfig.Interface[32].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[32].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[32].VLAN_Idx].IGMP_Querier_Enable = 1
 +[HWLAN] ifno=32 irno=7 port=0x00000000
 +***** [iput_IpLinkUp] ifno=32, link_type:12
 +Interface 32 ip = 192.168.1.254
 +
 +gConfig.Interface[33].IP_Addr = 0.0.0.0
 +gConfig.Interface[33].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[33].Description = WDS3
 +gConfig.Interface[33].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[33].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[33].VLAN_Idx].IGMP_Querier_Enable = 1
 +[HWLAN] ifno=33 irno=7 port=0x00000000
 +***** [iput_IpLinkUp] ifno=33, link_type:12
 +Interface 33 ip = 192.168.1.254
 +
 +gConfig.Interface[34].IP_Addr = 0.0.0.0
 +gConfig.Interface[34].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[34].Description = WDS4
 +gConfig.Interface[34].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[34].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[34].VLAN_Idx].IGMP_Querier_Enable = 1
 +[HWLAN] ifno=34 irno=7 port=0x00000000
 +***** [iput_IpLinkUp] ifno=34, link_type:12
 +Interface 34 ip = 192.168.1.254
 +
 +gConfig.Interface[35].IP_Addr = 0.0.0.0
 +gConfig.Interface[35].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[35].Description = COM1
 +pppInit> set (PPPShutdownRequest[35] = 0), do_connect_in_progress[35]=0
 +[change_phase] start to release the allocated memory in if_table[0].ppp_p->state
 +if_umts_init() WAN interface 35, UMTS-COM1: baudrate=115200
 +if_umts_init() MAC:1C:C6:3C:C4:3D:A8
 +RUNTASK id=2 umtsEventHandleTsk...
 +RUNTASK id=3 umtsEventExeHandleTsk...
 +RUNTASK id=4 umtsReceQueueTsk...
 +RUNTASK id=5 umtsReceTsk...
 +RUNTASK id=6 umtsWritTsk...
 +Interface 35 ip = 0.0.0.0
 +
 +gConfig.Interface[36].IP_Addr = 192.168.2.253
 +gConfig.Interface[36].Subnet_Mask = 255.255.255.0
 +gConfig.Interface[36].Description = APLAN
 +ruleCheck()> Group: 0,  Error: Useless rule index will be truncated, from idx:2
 +ruleCheck()> Group: 1,  Error: Useless rule index will be truncated, from idx:22
 +ruleCheck()> Group: 2,  Error: Useless rule index will be truncated, from idx:0
 +CBAC rule format check succeed !!
 +reqCBACBuf()> init match pool, Have: 1000
 +Memory Address: 0xffffffff81168514 ~ 0xffffffff8116f290
 +reqCBACBuf()> init timeGap pool, Have: 10000
 +Memory Address: 0xffffffff8116f290 ~ 0xffffffff8119ffe4
 +reqCBACBuf()> init sameHost pool, Have: 2000
 +Memory Address: 0xffffffff8119ffe4 ~ 0xffffffff811afa04
 +CBAC rule pool initialized !!
 +Init NAT data structure
 +No default route, no need to reinit the NAT data structure
 +RUNTASK id=7 if_task if0...
 +RUNTASK id=8 if_task if1...
 +RUNTASK id=9 if_task if2...
 +RUNTASK id=10 if_task if3...
 +RUNTASK id=11 if_task if4...
 +RUNTASK id=12 if_task if31...
 +RUNTASK id=13 if_task if32...
 +RUNTASK id=14 if_task if33...
 +RUNTASK id=15 if_task if34...
 +RUNTASK id=16 if_task if35...
 +RUNTASK id=17 if_task if36...
 +RUNTASK id=18 timer_task...
 +RUNTASK id=19 conn_mgr...
 +RUNTASK id=20 main_8021x...
 +RUNTASK id=21 saveRandomSeedTask...
 +vfs_codepage_init() TimeZone:23, vfs_cp_idx:23, vfs_cp_ID:5
 +fat_codePageInit() TimeZone:23, codePage:CP850, cPID:5, cpSize:256, toUpSize:30
 +==[vfs_register_filesystem]============================
 +list size:1,  Method:0x808f5cfc
 +  1) Type:0xfc, Name:BRN-VFS
 +=================================================================
 +==[vfs_register_filesystem]============================
 +list size:7,  Method:0x808f5e88
 +  1) Type:0x01, Name:FAT12
 +  2) Type:0x04, Name:FAT16
 +  3) Type:0x06, Name:FAT16
 +  4) Type:0x0b, Name:FAT32
 +  5) Type:0x0c, Name:FAT32
 +  6) Type:0x0e, Name:FAT16
 +  7) Type:0x81, Name:Minix
 +=================================================================
 +[0-START]=========================================
 +  Node 000-[\],  DIR, MountFlag:0x00
 +[0-END]===========================================
 +  [1-START]=========================================
 +    Node 001-[dev],  DIR, MountFlag:0x00
 +  [1-END]===========================================
 +  [1-START]=========================================
 +    Node 002-[mnt],  DIR, MountFlag:0x00
 +  [1-END]===========================================
 +dump_inode() freeCnt:77, usedCnt:3
 +otg_host_power_set() USB Host0 Power OFF
 +usb_host_power_set() isOn:1
 +otg_host_power_set() USB Host1 Power OFF
 +usb_host_power_set() isOn:1
 +RUNTASK id=23 period_task...
 +
 +========== ADSL Modem initialization OK ! ======
 +
 +[Dhcpd_Start]
 +RUNTASK id=24 dhcp_daemon...
 +main()> usb:1, ftp:0
 +found signature: 78h 56h 34h 12h
 +ulImgLens=2166494, LENGTH[5]-12=7864308, type:0
 +length checking OK
 +[0]2 find End at 0xFFFFFFFFB0290C00 len=2166494, type=0
 +found signature: 78h 56h 34h 12h
 +ulImgLens=6978, LENGTH[5]-12=7864308, type:10
 +length checking OK
 +[1]2 find End at 0xFFFFFFFFB0292800 len=6978, type=10
 +found signature: 78h 56h 34h 12h
 +ulImgLens=12616, LENGTH[5]-12=7864308, type:11
 +length checking OK
 +[2]2 find End at 0xFFFFFFFFB0295C00 len=12616, type=11
 +found signature: 78h 56h 34h 12h
 +ulImgLens=231260, LENGTH[5]-12=7864308, type:12
 +length checking OK
 +[3]2 find End at 0xFFFFFFFFB02CE400 len=231260, type=12
 +---[ LZMA head start in 0xFFFFFFFFB02CE800 ]---
 +found signature: 78h 56h 34h 12h
 +ulImgLens=365159, LENGTH[5]-12=7864308, type:50
 +length checking OK
 +[4]2 find End at 0xFFFFFFFFB0327800 len=365159, type=50
 +---[ LZMA head start in 0xFFFFFFFFB0327C00 ]---
 +found signature: 78h 56h 34h 12h
 +ulImgLens=363500, LENGTH[5]-12=7864308, type:90
 +length checking OK
 +[5]2 find End at 0xFFFFFFFFB0380800 len=363500, type=90
 +---[ LZMA head start in 0xFFFFFFFFB0380C00 ]---
 +found signature: 78h 56h 34h 12h
 +ulImgLens=202985, LENGTH[5]-12=7864308, type:8
 +length checking OK
 +[6]2 find End at 0xFFFFFFFFB03B2400 len=202985, type=8
 +[get_web_address] Web-0:  addr:0xb0291000, len:6978, type:10
 +[get_web_address] Web-1:  addr:0xb0292c00, len:12616, type:11
 +[get_web_address] Web-2:  addr:0xb0296000, len:231260, type:12
 +RUNTASK httpd...
 +RUNTASK id=28 SSLClient ...
 +g_Client_Cert_Array=0x81c49558
 +RUNTASK id=29 dnsproxy...
 +RUNTASK id=30 dhcpd_mgmt_task...
 +runDDNS() ddns_enable:0, DDNSTaskRun:0, needReRunDDNS:1
 +UPnP task run-up... upnpFunc:1
 +UPNP Device initialize success! slot=31
 +TR64 is enabled
 +TR64 Device initialize success! slot=32
 +RUNTASK id=35 wscmain...
 +RUNTASK id=36 wsc_Send_eap_packet...
 +RUNTASK id=37 wsc_Send_UPNP_packet...
 +RUNTASK id=38 WSC_WaitUserAction_Task...
 +UART RX Output
 +Starting Multitask...
 +
 +===== General exception ======
 +EPC  -> 0x80006F20
 +CO_SR -> 0x0000FC03
 +Register Dump: Saved Area : Begin 0x8166CC34 End 0x8166CDCF
 +RES:0x00000000
 + RA:0x8000585C
 + AT:0x809A0000
 + V0:0x80000010
 + V1:0x0000FC03
 + A0:0x00000015
 + A1:0x00000008
 + A2:0x01BC3854
 + T0:0x0000FC01
 + T1:0x00000000
 + T2:0x0000005A
 + T3:0x00000001
 + T4:0x00000000
 + T5:0x00000000
 + T6:0x0FFFFFFF
 + T7:0x0000000F
 + T8:0x808AF8F5
 + T9:0x00000000
 + S0:0x00000BB8
 + S1:0x00000015
 + S2:0x00000015
 + S3:0xFFFFFFFF
 + S4:0x00000001
 + S5:0x00000000
 + S6:0x01E02108
 + S7:0xC1838500
 + S8:0x3052E99D
 +EPC:0x80006F20
 + SR:0x0000FC03
 + CAUSE:0x80000010
 + Instruction : 0x14628821
 + SP (Save Point) :0x8166CC34
 +==============================
 +
 +===================
 +Print call path
 +0x00000000,Function=0x80006EC0  PC=0x80006F20
 +0x00000001,Function=0x8000584C  PC=0x80005854
 +0x00000002,Function=0x00000000  PC=0x80005844
 +
 +===================
 +
 +===================
 +Print call stacks
 +0x00000000 Stack:
 +0x8166CEF0: 0x00000BB8 0x00000015 0x00000064 0x80113704
 +0x8166CF00: 0x00000001 0x8000585C 0xC1838500 0x00000000
 +
 +0x00000001 Stack:
 +0x8166CF10: 0x8000584C 0x00000000 0x80113704 0x00000000
 +
 +</code>
 +</p>
 +</HTML>
 +
 +==== u-boot bootlog ====
 +<HTML>
 +<p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF">
 +<code>
 +
 +U-Boot 2013.04-rc1-g9d05354-dirty (Jul 06 2013 - 01:13:10) VGV7519
 +
 +Board: Arcadyan VGV7519 VRX288 Board
 +SoC:  Lantiq VRX288 v1.1
 +CPU:  500 MHz
 +IO:    250 MHz
 +BUS:  250 MHz
 +BOOT:  NOR
 +DRAM:  64 MiB
 +Flash: 16 MiB
 +In:    serial
 +Out:  serial
 +Err:  serial
 +Net:  ltq-eth
 +VGV7519 #
</code> </code>
Line 241: Line 888:
<code> <code>
-PUT HERE YOUR BOOTLOG+ROM VER: 1.0.5 
 +CFG 01 
 + 
 + 
 +U-Boot 2014.04-g1702a40-dirty (Jun 21 2014 - 16:13:24) VGV7519 
 + 
 +Board: Arcadyan VGV7519 VRX288 Board 
 +SoC:  Lantiq VRX288 v1.1 
 +CPU:  500 MHz 
 +IO:    250 MHz 
 +BUS:  250 MHz 
 +BOOT:  NOR 
 +DRAM:  64 MiB 
 +Flash: 16 MiB 
 +*** Warning - bad CRC, using default environment 
 + 
 +In:    serial 
 +Out:  serial 
 +Err:  serial 
 +Net:  firmware: using built-in firmware lantiq/vrx200_phy11g_a1x.fw 
 +ltq-eth 
 +Hit any key to stop autoboot:  0 
 +Wrong Image Format for bootm command 
 +ERROR: can't get kernel image! 
 +VGV7519 # bootm 0xB0080000 
 +## Booting kernel from Legacy Image at b0080000 ... 
 +  Image Name:  MIPS OpenWrt Linux-3.10.36 
 +  Created:      2014-06-21  11:50:30 UTC 
 +  Image Type:  MIPS Linux Kernel Image (lzma compressed) 
 +  Data Size:    1414748 Bytes = 1.3 MiB 
 +  Load Address: 80002000 
 +  Entry Point:  80002000 
 +  Verifying Checksum ... OK 
 +  Uncompressing Kernel Image ... OK 
 + 
 +Starting kernel ... 
 + 
 +[    0.000000] Linux version 3.10.36 (thelizard@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41296) ) #1 Sat Jun 21 13:50:23 CEST 2014 
 +[    0.000000] SoC: VR9 rev 1.1 
 +[    0.000000] bootconsole [early0] enabled 
 +[    0.000000] CPU revision is: 00019555 (MIPS 34Kc) 
 +[    0.000000] Determined physical RAM map: 
 +[    0.000000]  memory: 04000000 @ 00000000 (usable) 
 +[    0.000000] Initrd not found or empty - disabling initrd 
 +[    0.000000] Zone ranges: 
 +[    0.000000]  Normal  [mem 0x00000000-0x03ffffff] 
 +[    0.000000] Movable zone start for each node 
 +[    0.000000] Early memory node ranges 
 +[    0.000000]  node  0: [mem 0x00000000-0x03ffffff] 
 +[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. 
 +[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256 
 +[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit 
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) 
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) 
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) 
 +[    0.000000] Writing ErrCtl register=0007cf41 
 +[    0.000000] Readback ErrCtl register=0007cf41 
 +[    0.000000] Memory: 60476k/65536k available (3008k kernel code, 5060k reserved, 1018k data, 188k init, 0k highmem) 
 +[    0.000000] NR_IRQS:256 
 +[    0.000000] CPU Clock: 500MHz 
 +[    0.000000] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088) 
 +[    0.032000] pid_max: default: 32768 minimum: 301 
 +[    0.036000] Mount-cache hash table entries: 512 
 +[    0.040000] pinctrl core: initialized pinctrl subsystem 
 +[    0.044000] NET: Registered protocol family 16 
 +[    0.056000] pinctrl-xway 1e100b10.pinmux: Init done 
 +[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28 
 +[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV 
 +[    0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185] 
 +[    0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193] 
 +[    0.284000] ifx_pcie_wait_phy_link_up timeout 
 +[    0.288000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185] 
 +[    0.400000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193] 
 +[    0.500000] ifx_pcie_wait_phy_link_up timeout 
 +[    0.504000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185] 
 +[    0.616000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193] 
 +[    0.716000] ifx_pcie_wait_phy_link_up timeout 
 +[    0.720000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185] 
 +[    0.832000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193] 
 +[    0.932000] ifx_pcie_wait_phy_link_up timeout 
 +[    0.936000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185] 
 +[    1.048000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193] 
 +[    1.148000] ifx_pcie_wait_phy_link_up timeout 
 +[    1.152000] pcie_rc_initialize link up failed!!!!! 
 +[    1.164000] bio: create slab <bio-0> at 0 
 +[    1.168000] gpio-stp-xway 1e100bb0.stp: Init done 
 +[    1.172000] usbcore: registered new interface driver usbfs 
 +[    1.176000] usbcore: registered new interface driver hub 
 +[    1.180000] usbcore: registered new device driver usb 
 +[    1.184000] Switching to clocksource MIPS 
 +[    1.192000] NET: Registered protocol family 2 
 +[    1.196000] TCP established hash table entries: 512 (order: 0, 4096 bytes) 
 +[    1.200000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) 
 +[    1.208000] TCP: Hash tables configured (established 512 bind 512) 
 +[    1.216000] TCP: reno registered 
 +[    1.216000] UDP hash table entries: 256 (order: 0, 4096 bytes) 
 +[    1.224000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) 
 +[    1.232000] NET: Registered protocol family 1 
 +[    1.236000] gptu: totally 6 16-bit timers/counters 
 +[    1.240000] gptu: misc_register on minor 63 
 +[    1.244000] gptu: succeeded to request irq 126 
 +[    1.248000] gptu: succeeded to request irq 127 
 +[    1.252000] gptu: succeeded to request irq 128 
 +[    1.256000] gptu: succeeded to request irq 129 
 +[    1.264000] gptu: succeeded to request irq 130 
 +[    1.268000] gptu: succeeded to request irq 131 
 +[    1.272000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a1x.bin 
 +[    1.280000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 38C0000 
 +[    1.288000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 38C0000 
 +[    1.396000] squashfs: version 4.0 (2009/01/31) Phillip Lougher 
 +[    1.404000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 
 +[    1.412000] msgmni has been set to 118 
 +[    1.416000] io scheduler noop registered 
 +[    1.420000] io scheduler deadline registered (default) 
 +[    1.428000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc 
 +[    1.436000] console [ttyLTQ0] enabled, bootconsole disabled 
 +[    1.436000] console [ttyLTQ0] enabled, bootconsole disabled 
 +[    1.448000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00007f Chip ID 0x0022cb 
 +[    1.456000] Amd/Fujitsu Extended Query Table at 0x0040 
 +[    1.464000]  Amd/Fujitsu Extended Query version 1.1. 
 +[    1.468000] number of CFI chips: 1 
 +[    1.472000] 3 ofpart partitions found on MTD device ltq_nor 
 +[    1.476000] Creating 3 MTD partitions on "ltq_nor": 
 +[    1.480000] 0x000000000000-0x000000040000 : "uboot" 
 +[    1.488000] 0x000000060000-0x000000070000 : "uboot_env" 
 +[    1.492000] 0x000000080000-0x000001000000 : "firmware" 
 +[    1.496000] mtd: partition "firmware" extends beyond the end of device "ltq_nor" -- size truncated to 0x780000 
 +[    1.508000] 0x0000001d969c-0x000000800000 : "rootfs" 
 +[    1.512000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only 
 +[    1.528000] mtd: device 3 (rootfs) set to be root filesystem 
 +[    1.532000] mtd: partition "rootfs_data" created automatically, ofs=0x3f0000, len=0x410000 
 +[    1.540000] 0x0000003f0000-0x000000800000 : "rootfs_data" 
 +[    1.672000] libphy: lantiq,xrx200-mdio: probed 
 +[    1.680000] net-xrx200: invalid MAC, using random 
 +[    1.684000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1) 
 +[    1.692000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1) 
 +[    1.700000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1) 
 +[    1.708000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1) 
 +[    1.716000] net-xrx200: invalid MAC, using random 
 +[    1.720000] eth1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1) 
 +[    1.728000] wdt 1f8803f0.watchdog: Init done 
 +[    1.732000] leds-gpio gpio-leds.7: pins are not configured from the driver 
 +[    1.744000] TCP: cubic registered 
 +[    1.744000] NET: Registered protocol family 17 
 +[    1.752000] 8021q: 802.1Q VLAN Support v1.8 
 +[    1.760000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19 
 +[    1.772000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. 
 +[    1.776000] Freeing unused kernel memory: 188K (803f1000 - 80420000) 
 +[    2.700000] eth0: port 0 got link 
 +procd: Console is alive 
 +procd: - watchdog - 
 +[    4.572000] IFXUSB: ifxusb_hcd: version 3.2 B110801 
 +[    4.576000] Chip Version :01c0 BurstSize=0 
 +[    5.180000] IFXUSB: USB core #0 soft-reset 
 +[    5.484000] IFXUSB: USB core #0 soft-reset 
 +[    5.488000] ifxusb_hcd ifxusb_hcd: IFX USB Controller 
 +[    5.492000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1 
 +[    5.500000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000 
 +[    5.504000] IFXUSB: Init: Power Port (0) 
 +[    5.512000] hub 1-0:1.0: USB hub found 
 +[    5.512000] hub 1-0:1.0: 1 port detected 
 +[    6.016000] IFXUSB: USB core #1 soft-reset 
 +[    6.320000] IFXUSB: USB core #1 soft-reset 
 +[    6.324000] ifxusb_hcd ifxusb_hcd: IFX USB Controller 
 +[    6.328000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2 
 +[    6.336000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000 
 +[    6.340000] IFXUSB: Init: Power Port (0) 
 +[    6.344000] hub 2-0:1.0: USB hub found 
 +[    6.348000] hub 2-0:1.0: 1 port detected 
 +[    6.352000] ifxusb_hcd ifxusb_hcd: requested GPIO 232 
 +procd: - preinit - 
 +Press the [f] key and hit [enter] to enter failsafe mode 
 +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level 
 +jffs2 is ready 
 +jffs2 is ready 
 +[    9.832000] jffs2: notice: (267) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 9 of xref (0 dead, 2 orphan) found. 
 +switching to overlay 
 +procd: - early - 
 +procd: - watchdog - 
 +procd: - ubus - 
 +procd: - init - 
 +Please press Enter to activate this console. 
 +[  11.252000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH 
 + 
 +[  11.276000] NET: Registered protocol family 10 
 +[  11.284000] NET: Registered protocol family 8 
 +[  11.288000] NET: Registered protocol family 20 
 +[  11.300000] sit: IPv6 over IPv4 tunneling driver 
 +[  11.316000] PPP generic driver version 2.4.2 
 +[  11.336000] nf_conntrack version 0.5.0 (947 buckets, 3788 max) 
 +[  11.352000] ip6_tables: (C) 2000-2006 Netfilter Core Team 
 +[  11.388000] MEI CPE Driver, Version 1.2.0 
 + 
 +[  11.392000] (c) Copyright 2009, Infineon Technologies AG 
 +### MEI CPE - MEI CPE - MEI CPE - MEI CPE ### 
 + 
 + 
 +Lantiq CPE API Driver version: DSL CPE API V4.11.4 
 +[  11.420000] 
 +[  11.420000] Predefined debug level: 2 
 +[  11.428000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea 
 +[  11.436000] Backport generated by backports.git backports-20140320-37-g5c33da0 
 +[  11.444000] ip_tables: (C) 2000-2006 Netfilter Core Team 
 +[  11.456000] Infineon Technologies DEU driver version 2.0.0 
 +[  11.460000] IFX DEU DES initialized (multiblock). 
 +[  11.468000] IFX DEU AES initialized (multiblock). 
 +[  11.472000] IFX DEU ARC4 initialized (multiblock). 
 +[  11.476000] IFX DEU SHA1 initialized. 
 +[  11.480000] IFX DEU MD5 initialized. 
 +[  11.484000] IFX DEU SHA1_HMAC initialized. 
 +[  11.488000] IFX DEU MD5_HMAC initialized. 
 +[  11.508000] NET: Registered protocol family 24 
 +[  11.528000] xt_time: kernel timezone is -0000 
 +[  11.552000] cfg80211: Calling CRDA to update world regulatory domain 
 +[  11.556000] cfg80211: World regulatory domain updated: 
 +[  11.560000] cfg80211:  DFS Master region: unset 
 +[  11.564000] cfg80211:  (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) 
 +[  11.576000] cfg80211:  (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  11.584000] cfg80211:  (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  11.592000] cfg80211:  (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  11.600000] cfg80211:  (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  11.608000] cfg80211:  (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  11.616000] cfg80211:  (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) 
 +[  18.052000] device eth0 entered promiscuous mode 
 +[  18.060000] br-lan: port 1(eth0) entered forwarding state 
 +[  18.064000] br-lan: port 1(eth0) entered forwarding state 
 +[  20.068000] br-lan: port 1(eth0) entered forwarding state 
 +procd: - init complete -
</code> </code>
Line 247: Line 1122:
</HTML> </HTML>
 +===== Progress =====
 +
 +|USB: working  |https://dev.openwrt.org/ticket/16800#ticket  |
 +|WIFI: working |https://dev.openwrt.org/changeset/42907 (CC) |
 +|              |https://dev.openwrt.org/changeset/42906 (BB) |
 +             
===== Notes ===== ===== Notes =====
 +SIP:
 +
 +daemon to test:
 +sofia-sip
 +pjsip(already in openwrt)
 +owsip(already in openwrt)
 +
 +driver vmmc:
 +http://mirror2.openwrt.org/sources/drv_vmmc-1.9.0.tar.bz2
 +drv_vmmc-1.9.0/FEATURES_and_OPEN_ISSUES
 +* TAPI 3.13.0.2, drv_vmmc 1.9.0.3, KPI 2.2.0.0, MPS 2.2.2.5
 +* XWAY VRX288 VoIP Firmware  2.1.0.7.0
 +Original firmware 1.9.0.4
 +
 +need firmware dump for dsl, voip and coef + populate openwrt/package/ifx-vmmc/Makefile
 +
 +driver tapi:
 +http://mirror2.openwrt.org/sources/drv_tapi-3.13.0.tar.bz2
 +Same level as original firmware
 +
 +http://dev.phrozen.org/ltq-mirror/ (dsl and other stuff)
 +
 +DSL:
 +available version 4.11.4 - my firmware version: 4.12.4 - May works
 +need firmware dump
 +
 +SWITCH:
 +look at switch_utils note at http://wiki.openwrt.org/toh/tp-link/td-w8970#switch_utility
 +we need to decompile original firmware and recovery switch initialization params
 +
 +FXO:
 +Si3050+Si3011 should be a FXO interface. It seems they implemented FXO using external component.
 +
 +WIFI:
 +I haven't decapped the shield, but by looking to original SuperTask firmware, it seems to be RT3090 Minipci + NICInitRT5390RF
===== Tags ===== ===== Tags =====
For some Help with the Tags, please have a look here: [[meta/tags]] For some Help with the Tags, please have a look here: [[meta/tags]]
-{{tag>GigabitEthernet FastEthernet 5Port 2PHY USB 2USB ath9k 64RAM 16Flash MIPS MIPS32 34K}}+{{tag>GigabitEthernet 4Port 1NIC 1WNIC USB 2USB ath9k 64RAM 16Flash MIPS MIPS32 34K lantiq VR9 VDSL2 JTAG}}

Back to top

toh/arcadyan/vgv7519.1368955514.txt.bz2 · Last modified: 2013/05/19 11:25 (external edit)