Differences

This shows you the differences between two versions of the page.

toh:arcadyan:vgv7519 [2013/07/07 11:48]
toh:arcadyan:vgv7519 [2014/11/06 09:46] (current)
cornelus2009
Line 1: Line 1:
====== Astoria networks VGV7519 ====== ====== Astoria networks VGV7519 ======
-There seem to be ARV7519RW (aka Livebox 2.1) and ARV7519KW (aka KPN Experia Box v8).+There seem to be ARV7519KW (aka KPN Experia Box v8).
===== Supported Versions ===== ===== Supported Versions =====
-^ Version/Model ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^ +^ Version/Model ^ Device ^ S/N ^ OpenWrt Version Supported ^ Model Specific Notes ^  
-| v1  ? | J229112404 | ? | KPN Experia Box V8 |+| R01  Experia Box V8 | J229112404 | [[https://dev.openwrt.org/changeset/38266/trunk|r38266]] | KPN logo on the front | 
 +|  R02  |  Experia Box V8 | J229112404 | [[https://dev.openwrt.org/changeset/38266/trunk|r43072]] (BB: [[https://dev.openwrt.org/changeset/38266/trunk|r43075]]) | No KPN logo on the front |
 +Hardware version can be can be found in the interface
**NOTE:** Anything not included in model specific notes, or where a short comment couldn't be included on the [[#notes]]. **NOTE:** Anything not included in model specific notes, or where a short comment couldn't be included on the [[#notes]].
===== Hardware Highlights ===== ===== Hardware Highlights =====
-^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ +^ Version ^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ External PHY version
-| Lantiq Xway VRX288 | 64MiB | 16MiB | 4 x 1 | 2 | Yes | EJTAG (14p) |+| R01 | Lantiq Xway VRX288 V1.1 | 64MiB | 16MiB | 4 x 1 | 2 | Yes | EJTAG (14p) | V1.3 | 
 +| R02 | Lantiq Xway VRX288 V1.2 | 64MiB | 16MiB | 4 x 1 | 2 | Yes | EJTAG (14p) | V1.5 |
Line 26: Line 29:
Note that the only working method is using JTAG! Note that the only working method is using JTAG!
 +
 +The best approach for migration to OpenWRT is as follows:
 +  * Open your device
 +  * Connect JTAG
 +  * Backup original flash image
 +  * Download U-BOOT ram image: [[https://github.com/openwrt-vgv7519/uboot-bin/blob/master/ram/u-boot.bin]]
 +  * Download U-BOOT flash image: [[https://github.com/openwrt-vgv7519/uboot-bin/blob/master/flash/u-boot.bin]]
 +  * Use JTAG to start ram image of u-boot
 +  * Download and flash image to the device using tftp
 +
 +  * Download openwrt source tree and build images for VGV-7519 with squashfs image.
 +  * Flash the squashfs image using tftp
 +
==== Original Flash Layout ==== ==== Original Flash Layout ====
Line 49: Line 65:
^  Arcadyan VGV7519 Flash Layout          ^^^^^^^^ ^  Arcadyan VGV7519 Flash Layout          ^^^^^^^^
^ Layer0      |                      EN29LV640AB-90TIP  8192KiB                                                                      |||||  EN29LV640AB-90TIP 8192KiB  || ^ Layer0      |                      EN29LV640AB-90TIP  8192KiB                                                                      |||||  EN29LV640AB-90TIP 8192KiB  ||
-^ Layer1      |  mtd0 **//u-boot//** |  reserved  |  **//u-boot-env//**  |  reserved  |  mtd5 **//firmware//** 15872KiB                                      ||||+^ Layer1      |  mtd0 **//u-boot//** |  art **//config-params//** |  **//u-boot-env//**  |  reserved  |  mtd5 **//firmware//** 15872KiB                                      ||||
^ Layer2      |                              ||||  mtd1 **//kernel//** 1984KiB  |  mtd2 **//rootfs//** 13888KiB                          || ^ Layer2      |                              ||||  mtd1 **//kernel//** 1984KiB  |  mtd2 **//rootfs//** 13888KiB                          ||
^ <color magenta>mountpoint</color>  |      ||||                              |  <color magenta>''/''</color>                          || ^ <color magenta>mountpoint</color>  |      ||||                              |  <color magenta>''/''</color>                          ||
^ filesystem  |                              ||||                              |  [[doc:techref:filesystems#mini_fo|mini_fo]]/[[doc:techref:filesystems#overlayfs|overlayfs]]          || ^ filesystem  |                              ||||                              |  [[doc:techref:filesystems#mini_fo|mini_fo]]/[[doc:techref:filesystems#overlayfs|overlayfs]]          ||
^ Layer3      |                              ||||                              |                |  mtd3 **//rootfs_data//** 11904KiB    | ^ Layer3      |                              ||||                              |                |  mtd3 **//rootfs_data//** 11904KiB    |
-^ Size in KiB  |  256KiB  |  128KiB |  64KiB  |  64KiB  |                      1984KiB                      |  1984KiB        |  11904KiB    | +^ Size in KiB  |  256KiB  |  64KiB |  64KiB  |  64KiB  |                      1984KiB                      |  1984KiB        |  11904KiB    | 
-^ Name        |  **//u-boot//**             |  //none//  | **//u-boot env//** |  //none//  |  **//kernel//**              |                |  **//rootfs_data//**            |+^ Name        |  **//u-boot//** **//board_config//** | **//u-boot env//** |  //none//  |  **//kernel//**              |                |  **//rootfs_data//**            |
^ <color magenta>mountpoint</color>          |  //none//  |  //none//  |  //none//  |  //none//  |  //none//                    |  <color magenta>''/rom''</color>  |  <color magenta>''/overlay''</color>  | ^ <color magenta>mountpoint</color>          |  //none//  |  //none//  |  //none//  |  //none//  |  //none//                    |  <color magenta>''/rom''</color>  |  <color magenta>''/overlay''</color>  |
^ filesystem  |    //none//                  |  //none//  |  //none//  |  //none//  |  //none//  |  [[doc:techref:filesystems#SquashFS]]      || ^ filesystem  |    //none//                  |  //none//  |  //none//  |  //none//  |  //none//  |  [[doc:techref:filesystems#SquashFS]]      ||
==== OEM easy installation ==== ==== OEM easy installation ====
 +The easiest way is to enter the recovery mode as described in [[doc/techref/bootloader/brnboot]]
 +Instead on what is documented on that page, for this model the recovery web interface is available on http://192.168.2.254/
-As the bootloaders password is still unknown, the only way to flash it, would be to use JTAG...+<color red>Additionally the page request for a PIN code which is still unknown... 
 +This PIN-code is also SHA-1 hashed and compared, I have no idea about constraints, the hash as taken from the disassembly is: 
 +B16D0EF3 DD0632DC D13D135E 02A097AE C4044C24</color> 
 + 
 +The bootloader's serial console is another option, but there is a SHA-1 hashed password as well. 
 +There are 2 ways to flash it, use UART BOOT mod or JTAG...
I have managed to patch the password protection code sequence out, so I am able to gain access to the bootloader menu. I have managed to patch the password protection code sequence out, so I am able to gain access to the bootloader menu.
The loader itself won't let you erase or overwrite the first sectors so it is useless for flashing another bootloader. The loader itself won't let you erase or overwrite the first sectors so it is useless for flashing another bootloader.
 +
 +Administrator mode is aquired by pressing '!'
 +Sniffing around through the bootloader disassembly shows some differences, these are explained in the last column
The VR9 bootloader has the following menu options: The VR9 bootloader has the following menu options:
-| [#] | Set Serial Number | +|    | Menu item | Admin mode? | comments |  
-| [2] | Use Normal Firmware | +| [#] | Set Serial Number | |
-| [3] | Use ART-Testing Firmware | +| [2] | Use Normal Firmware | | not implemented
-| [9] | Taggle ART Firmware Enable/Disable | +| [3] | Use ART-Testing Firmware | | not implemented
-| [A] | Set MAC Address | +| [9] | Taggle ART Firmware Enable/Disable | |
-| [B] | Set WPA Key | +| [A] | Set MAC Address | |
-| [E] | Erase Flash | +| [B] | Set WPA Key | |
-| [G] | Run Runtime Code | +| [E] | Erase Flash | |
-| [H] | Set Options | +| [G] | Run Runtime Code | |
-| [P] | Print Boot Params | +| [H] | Set Options | | | 
-| [U] | Upload to Flash | +| [I] | Unlisted | | Doesn't show menu, guess it is patched out | 
-| [V] | Set Board Version |+| [L] | Unlisted | | Doesn't show menu, guess it is patched out | 
 +| [M] | Upload to Memory | X |
 +| [P] | Print Boot Params | | | 
 +| [R] | Read from Memory | X | | 
 +| [S] | Unlisted | | Doesn't show menu, guess it is patched out | 
 +| [T] | Test Memory (not listed as option) | | Found in disassembly
 +| [U] | Upload to Flash | |
 +| [V] | Set Board Version | | | 
 +| [W] | Write to Memory | X | | 
 +| [Y] | Go to Memory | X | | 
 +| [Z] | Dump DDR Ram Register | X | | 
 +| [0] | Primary = Image 0 | X | | 
 +| [1] | Primary = Image 1 | X | | 
 + 
 +==== UART method ==== 
 + 
 +The installation procedure in short: 
 +  - Short the bootsel_0 pins (R159), apply VCC (3V3) to the R155 side of R154 (bootsel_2) and power on the router. 
 +  - Upload a special U-Boot RAM image using a serial cable 
 +  - Use U-Boot to erase the flash and install U-Boot to flash 
 +  - Power off the router, unshort the bootsel_0 pins, remove VCC from R154 and power on again 
 +  - Use the installed U-Boot to install OpenWrt to flash 
 + 
 +=== Preparation === 
 + 
 +You need a RS232-to-TTL cable connected to the serial header shown in the picture below. Short the UART boot pins with two jumper caps. 
 + 
 +{{:media:vgv7519_bootsel.jpg|}} 
 +(NOTE: bootsel_4 and bootsel_1 are just in the image for reference) 
 + 
 +Start TFTP server on your computer and copy ''openwrt-lantiq-vgv7519_nor-u-boot.img'' and ''openwrt-lantiq-xway-VGV7519-squashfs.image'' to the TFTP server root. Connect your computer to the router with an ethernet cable and configure the IP address to 192.168.1.2, netmask 255.255.255.0. 
 + 
 +=== Loading U-Boot === 
 + 
 +Use 115200 bps, 8-N-1, no flow control, as the serial connection parameter. 
 + 
 +Power on the router. You should see 
 +<code> 
 +ROM VER: 1.0.5 
 +CFG 04 
 +UART 
 +</code> 
 +on the serial output. 
 + 
 +Send ''openwrt-lantiq-arv7510pw_ram-u-boot.asc'' as raw ascii to the router. U-Boot should start. Press any key to stop autoboot. At this point you can make a backup of the original firmware using ''md.l 0xb0000000 0x1000000'' and logging the output (takes roughly 2 hours). The flash can be erased by issuing first ''protect off all'' and then ''erase all''. Use first ''setenv ipaddr 192.168.1.1'', ''setenv serverip 192.168.1.2'' and ''setenv ethaddr xx:xx:xx:xx:xx:xx'' (ethernet address can be found from the sticker on top of the switch ports) to configure the network, and then ''tftp 0x80700000 openwrt-lantiq-arv7510pw_nor-u-boot.img'' to transfer the actual U-Boot image to memory. Write it to flash using ''cp.b 0x80700000 0xb0000000 ${filesize}''. Power off the router and remove the jumper caps from UART boot pins. 
 + 
 +=== Loading OpenWrt === 
 + 
 +Power on the router. The U-Boot installed in the previous step should start. Press any key to stop autoboot. Use again ''setenv ipaddr 192.168.1.1'', ''setenv serverip 192.168.1.2'' and ''setenv ethaddr xx:xx:xx:xx:xx:xx'' to configure the network. Use ''saveenv'' to save these to flash. Use ''tftp 0x80700000 openwrt-lantiq-xway-VGV7519-squashfs.image'' to transfer the actual OpenWRT image to memory. Write it to flash using ''cp.b 0x80700000 0xb0060000 ${filesize}''. Use ''reset'' to reset the board. Watch as U-Boot loads OpenWrt and proceed to configure it to your liking!
Line 148: Line 222:
| Reset | reset | back | | | Reset | reset | back | |
| ECO | ? | side | disables USB & WIFI | | ECO | ? | side | disables USB & WIFI |
-| Wifi enable | ? | side | | +| Wifi enable | rfkill | side | | 
-| Secure Easy Setup | ses | side | |+| wps | wps | side | |
Line 156: Line 230:
| **[[wp>Instruction set|Architecture]]:**    | [[wp>MIPS architecture|MIPS]] | | **[[wp>Instruction set|Architecture]]:**    | [[wp>MIPS architecture|MIPS]] |
| **Vendor:**          | [[wp>Lantiq]] | | **Vendor:**          | [[wp>Lantiq]] |
-| **[[doc:techref:Bootloader]]:**    | [[doc:techref:bootloader:uboot|U-Boot]] |+| **[[doc:techref:Bootloader]]:**    | [[doc:techref:bootloader:brnboot|BRNBoot]] |
| **[[doc:hardware:soc|System-On-Chip]]:**  | VRX288 V1.1 (MIPS, PSB 80920 EL) | | **[[doc:hardware:soc|System-On-Chip]]:**  | VRX288 V1.1 (MIPS, PSB 80920 EL) |
| **[[doc:hardware:cpu|CPU]]/Speed**        | 34Kc 500 Mhz | | **[[doc:hardware:cpu|CPU]]/Speed**        | 34Kc 500 Mhz |
Line 164: Line 238:
| **WAN:**            | 1x RJ45 | | **WAN:**            | 1x RJ45 |
| **Modem:**          | Infineon/Lantiq [[http://www.lantiq.com/uploads/tx_abzlantiqproducts/PB-e-0027-v2_lres.pdf|XWAY VRX208]]<html><br>VDSL2 (G.993.2),<br>VDSL1 (G.993.1, T1.424, TS 101 270),<br>ADSL1/2/2+ (G.992.1/3/5) Annexes A, B, I, J, M, L</html> | | **Modem:**          | Infineon/Lantiq [[http://www.lantiq.com/uploads/tx_abzlantiqproducts/PB-e-0027-v2_lres.pdf|XWAY VRX208]]<html><br>VDSL2 (G.993.2),<br>VDSL1 (G.993.1, T1.424, TS 101 270),<br>ADSL1/2/2+ (G.992.1/3/5) Annexes A, B, I, J, M, L</html> |
-| **Wireless:**        | (unknown for now) Atheros AR9103 2.4ghz 802.11bgn | +| **Wireless:**        | RALink RT5362F TPHR059609 1222STA1 2.4ghz 802.11bgn | 
-| **Ethernet:**        | (unknown for now) RealTek RTL8366RB Gigabit w/ vlan support [[doc:techref:swconfig]] |+| **Ethernet:**        | <del>(unknown for now) RealTek RTL8366RB Gigabit w/ vlan support [[doc:techref:swconfig]]</del> Internal configurable (Infineon) (3x lantiq PEF7071v) |
| **Internet:**        | ADSL2+  | | **Internet:**        | ADSL2+  |
-| **Phone:** | [[http://www.lantiq.com/products/voice-customer-premises-equipment/slictm/xwaytm-slic100/xwaytm-slic120/|Lantiq XWAY SLIC120 (PEF 42068 V V1.2)]], 3x FXS (TAE ports which provide POTS via a SIP gateway) |+| **Phone:** | [[http://www.lantiq.com/products/voice-customer-premises-equipment/slictm/xwaytm-slic100/xwaytm-slic120/|Lantiq XWAY SLIC120 (PEF 42068 V V1.2)]], 3x FXS (TAE ports which provide POTS via a SIP gateway) Si3050/Si3011fs |
| **USB:**            | Yes 2 x 2.0    | | **USB:**            | Yes 2 x 2.0    |
| **[[doc:hardware:port.serial|Serial]]:**          | [[#Serial|Yes]] | | **[[doc:hardware:port.serial|Serial]]:**          | [[#Serial|Yes]] |
Line 228: Line 302:
| **Function** |  GND  |  RX  |  TX  |  VCC (3.3V)  | | **Function** |  GND  |  RX  |  TX  |  VCC (3.3V)  |
-<color red>Hooking up to the serial with 115200/8N1 enables you to access the bootloader. You have to enter three spaces immediately after powerup after which you have to enter some secret password (seems to be 16 characters, but of course I have no idea what it would be... The SHA-1 hash for the password is: 42f25cd06c3e1d7096b35cbd3c3813c23adaf03a</color>+<color red>Hooking up to the serial with 115200/8N1 enables you to access the bootloader. You have to enter three spaces immediately after powerup after which you have to enter some secret password (seems to be 16 characters, but of course I have no idea what it would be... The SHA-1 hash for the password is:  
 +42f25cd06c3e1d7096b35cbd3c3813c23adaf03a</color>
For a photo see the second picture from the Main PCB section For a photo see the second picture from the Main PCB section
 +
 +==== GPIOs ====
 +
 +Generic VR9 gpio map (0xBE100B00+x):
 +|        |OUT    |IN      |DIR    |ALT0    |ALT1    |OD      |PUDSEL  |PUDEN |
 +|port0  |10      |14      |18      |1c      |20      |24      |2c      |30    |
 +|port1  |40      |44      |48      |4c      |50      |54      |5c      |60    |
 +|port2  |70      |74      |78      |7c      |80      |84      |8c      |90    |
 +|port3  |a0      |a4      |a8      |ac      |b0-53  |b4-34  |bc-38  |c0-3c |
 +
 +Generic pin id to bit:
 +|0      |1      |2      |3      |4      |5      |6      7      8      9      10      11      12      13      14      15
 +|0x1    |0x2    |0x4    |0x8    |0x10    |0x20    |0x40    0x80    0x100  0x200  0x400  0x800  0x1000  0x2000  0x4000  0x8000
 +
 +
 +Generic alternat to function:
 +|        |f0      |f1      |f2      |f3  |
 +|alt0    |0      |1      |0      |1    |
 +|alt1    |0      |0      |1      |1    |
 +
 +Function from disassembled 2.x firmware
 +|gpio03|???                              |      | od | dir|~alt0|~alt1            |gpio| 
 +|gpio04|stp                              |      | od | dir| alt0|~alt1            |stp | 
 +|gpio05|stp                              |      | od | dir| alt0|~alt1            |stp | 
 +|gpio06|stp                              |      | od | dir| alt0|~alt1            |stp | 
 +|gpio11|duslic(FXS)                      |      | od | dir|~alt0|~alt1            |gpio| 
 +|gpio12|CoC /USB HCD                    | out  | od | dir|~alt0|~alt1            |gpio| 
 +|gpio15|ProDAAInitialize(fxo)            |      |    |    |    |                  |    |
 +|gpio20|sip_core_mwi_led_off            |      |    |    |    |                  |    | 
 +|gpio21|pci                              |~out  | od | dir|~alt0|~alt1            |gpio| 
 +|gpio30|vmmc-relay                      | out  | od | dir|~alt0|~alt1            |gpio| 
 +|gpio32|hcd                              |      | od | dir|~alt0|~alt1            |gpio| 
 +|gpio37|reinjiection maybe voip related  |      |    |    |    |                  |    | 
 +|gpio42|mdio                            |      | od | dir| alt0|~alt1            |mdio| 
 +|gpio43|mdio                            |      | od | dir| alt0|~alt1            |mdio| 
 +|gpio47|???                              | out  | od | dir|~alt0|~alt1            |gpio| 
 +
 +-Eth led                                     
 +|gpio07 GPHY                            |      | od | dir| alt0| alt1            |gphy|
 +|gpio44 GPHY                            |      | od | dir| alt0| alt1            |gphy|
 +
 +-buttons
 +|gpio09|btn-rst                          | in    |    |~dir|~alt0|~alt1            |gpio|
 +|gpio10|btn-wps                          | in    |    |~dir|~alt0|~alt1            |gpio|
 +|gpio41|btn-echo                        | in    |    |~dir|~alt0|~alt1            |gpio| 
 +|gpio45|btn-wlan                        | in    |    |~dir|~alt0|~alt1            |gpio| 
==== JTAG ==== ==== JTAG ====
Line 278: Line 399:
In c_entry() function ... In c_entry() function ...
install_exception install_exception
 +
 +
 +Had to go a long way to retrieve the reset of this (crashing) bootlog
 +
 +[GPIO FLOW] SetGpio() Begin ..
 +[GPIO FLOW] SetGpio() End.
 +Runtime code version: 03.00.122
 +System startup...
 +Set flash memory layout to Boot Parameters found !!!
 +Bootcode version: v3.00.06
 +Serial number: J229112404
 +Hardware version: 01
 +06.07.2012-17:48:38
 +config_fnd=3, cfg_size=31115
 +cgi info size=31055, 0x55545352
 +Decompression ratio = 9.4
 +Signature matched at offset 279224
 +Add-on new config tail> oldSize:279264, oldCfgSize:13625, adjust length to -1
 +[CONFIG] read_config_from_flash ret=0
 +[CONFIG] load_config ret=1
 +cert_one:
 +-----BEGIN CERTIFICATE-----
 +MIIEnDCCBAWgAwIBAgIQdTN9mrDhIzuuLX3kRpFi1DANBgkqhkiG9w0BAQUFADBf
 +MQswCQYDVQQGEwJVUzEXMBUGA1UEChMOVmVyaVNpZ24sIEluYy4xNzA1BgNVBAsT
 +LkNsYXNzIDMgUHVibGljIFByaW1hcnkgQ2VydGlmaWNhdGlvbiBBdXRob3JpdHkw
 +HhcNMDUwMTE5MDAwMDAwWhcNMTUwMTE4MjM1OTU5WjCBsDELMAkGA1UEBhMCVVMx
 +FzAVBgNVBAoTDlZlcmlTaWduLCBJbmMuMR8wHQYDVQQLExZWZXJpU2lnbiBUcnVz
 +dCBOZXR3b3JrMTswOQYDVQQLEzJUZXJtcyBvZiB1c2UgYXQgaHR0cHM6Ly93d3cu
 +dmVyaXNpZ24uY29tL3JwYSAoYykwNTEqMCgGA1UEAxMhVmVyaVNpZ24gQ2xhc3Mg
 +MyBTZWN1cmUgU2VydmVyIENBMIIBIjANBgkqhkiG9w0BAQEFAAOCAQ8AMIIBCgKC
 +AQEAlcMhEo5AxQ0BX3ZeZpTZcyxYGSK4yfx6OZAqd3J8HT732FXjr0LLhzAC3Fus
 +cOa4RLQrNeuT0hcFfstG1lxToDJRnXRkWPkMmgDqXkRJZHL0zRDihQr5NO6ziGap
 +paRa0A6Yf1gNK1K7hql+LvqySHyN2y1fAXWijQY7i7RhB8m+Ipn4G9G1V2YETTX0
 +kXGWtZkIJZuXyDrzILHdnpgMSmO3ps6wAc74k2rzDG6fsemEe4GYQeaB3D0s57Rr
 +4578CBbXs9W5ZhKZfG1xyE2+xw/j+zet1XWHIWuG0EQUWlR5OZZpVsm5Mc2JYVjh
 +2XYFBa33uQKvp/1HkaIiNFox0QIDAQABo4IBgTCCAX0wEgYDVR0TAQH/BAgwBgEB
 +/wIBADBEBgNVHSAEPTA7MDkGC2CGSAGG+EUBBxcDMCowKAYIKwYBBQUHAgEWHGh0
 +dHBzOi8vd3d3LnZlcmlzaWduLmNvbS9ycGEwMQYDVR0fBCowKDAmoCSgIoYgaHR0
 +cDovL2NybC52ZXJpc2lnbi5jb20vcGNhMy5jcmwwDgYDVR0PAQH/BAQDAgEGMBEG
 +CWCGSAGG+EIBAQQEAwIBBjApBgNVHREEIjAgpB4wHDEaMBgGA1UEAxMRQ2xhc3Mz
 +Q0EyMDQ4LTEtNDUwHQYDVR0OBBYEFG/sr6DdiqTv9SoQZy0/VYK81+8lMIGABgNV
 +HSMEeTB3oWOkYTBfMQswCQYDVQQGEwJVUzEXMBUGA1UEChMOVmVyaVNpZ24sIElu
 +Yy4xNzA1BgNVBAsTLkNsYXNzIDMgUHVibGljIFByaW1hcnkgQ2VydGlmaWNhdGlv
 +biBBdXRob3JpdHmCEHC65B0Q2Sk0tjjKewPMur8wDQYJKoZIhvcNAQEFBQADgYEA
 +w34IRl2RNs9n3Nenr6+4IsOLBHTTsWC85v63RBKBWzFzFGNWxnIu0RoDQ1w4ClBK
 +Tc3athmo9JkNr+P32PF1KGX2av6b9L1S2T/L2hbLpZ4ujmZSeD0m+v6UNohKlV4q
 +TBnvbvqCPy0D79YoszcYz0KyNCFkR9MgazpM3OYDkAw=
 +-----END CERTIFICATE-----
 +default route: 0.0.0.0
 +[CheckUSBBackConf]Erase the garbage config in usbBackConf_s
 +BufferInit:
 +BUF_HDR_SZ=192 BUF_ALIGN_SZ=16 BUFFER_OFFSET=448
 +BUF_BUFSZ0=576 BUF_BUFSZ1=4352
 +NUM_OF_B0=0 NUM_OF_B1=2400
 +BUF_POOL0_SZ=0 BUF_POOL1_SZ=10905600
 +sizeof(BUFFER0)=768,sizeof(BUFFER1)=4544
 +*BUF0=0x828e681c *BUF1=0x81e7fffc
 +Altgn *BUF0=0x828e6820 *BUF1=0x81e80000
 +End at BUF0:0x828e6820, BUF1:0x828e6800
 +
 +BUF0[0]=0x828e6820 BUF1[0]=0x81e80000
 +
 +buffer0 pointer init OK!
 +buffer1 pointer init OK!
 +[qm_lnk_init] CLOCKHZ=1000 ...
 +[qm_lnk_init] add if 3 into QM link 0
 +[qm_lnk_init] add if 4 into QM link 0
 +[qm_cbq_enable] no QM attached
 +[qm_cbq_detach] no QM is attached at link 0
 +ptime=2000000/1000, cptime=20202/1000, offtime=40724/1000
 +New cls: id=0, bw=8 ns/byte, maxd=0 ms,
 +        maxb=32, minb=2, avgpktsz=250, maxpktsz=1600,
 +        offtime=1, parent=0, borrow=0
 +        pri=0, maxidle=1, minidle=-25,
 +        maxq=96, clsfg=17
 +ptime=12800000/1000, cptime=1280129299/1000, offtime=1280129299/1000
 +New cls: id=1, bw=808 ns/byte, maxd=0 ms,
 +        maxb=16, minb=1, avgpktsz=1600, maxpktsz=1600,
 +        offtime=1280, parent=8121049c, borrow=8121049c
 +        pri=5, maxidle=341, minidle=-2585,
 +        maxq=48, clsfg=21
 +qm_cbq_attach(): cbqp->cbq_res=107
 +ptime=2000000/1000, cptime=40608/1000, offtime=166340/1000
 +New cls: id=2, bw=8 ns/byte, maxd=0 ms,
 +        maxb=32, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=1, parent=8121049c, borrow=8121049c
 +        pri=5, maxidle=1, minidle=-26,
 +        maxq=48, clsfg=21
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=3, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=6, maxidle=0, minidle=-2560000,
 +        maxq=48, clsfg=20
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=4, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=0, maxidle=0, minidle=-2560000,
 +        maxq=96, clsfg=21
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=5, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=1, maxidle=0, minidle=-2560000,
 +        maxq=48, clsfg=23
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=6, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=2, maxidle=0, minidle=-2560000,
 +        maxq=48, clsfg=23
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=7, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=3, maxidle=0, minidle=-2560000,
 +        maxq=48, clsfg=23
 +ptime=2000000/1000, cptime=18446744073709551615/1000, offtime=18446744073709551615/1000
 +New cls: id=8, bw=799999 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=819241, parent=8120ee9c, borrow=8120ee9c
 +        pri=4, maxidle=0, minidle=-2560000,
 +        maxq=48, clsfg=23
 +ptime=2000000/1000, cptime=40608/1000, offtime=166340/1000
 +New cls: id=9, bw=8 ns/byte, maxd=0 ms,
 +        maxb=16, minb=4, avgpktsz=250, maxpktsz=1600,
 +        offtime=1, parent=8120ee9c, borrow=8120ee9c
 +        pri=6, maxidle=1, minidle=-26,
 +        maxq=48, clsfg=20
 +gConfig.Interface[0].IP_Addr = 127.0.0.1
 +gConfig.Interface[0].Subnet_Mask = 255.255.255.255
 +gConfig.Interface[0].Description = LOCAL_LOOPBACK
 +***** [iput_IpLinkUp] ifno=0, link_type:12
 +Interface 0 ip = 127.0.0.1
 +
 +gConfig.Interface[1].IP_Addr = 192.168.1.254
 +gConfig.Interface[1].Subnet_Mask = 255.255.255.0
 +gConfig.Interface[1].Description = LAN
 +gConfig.Interface[1].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[1].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[1].VLAN_Idx].IGMP_Querier_Enable = 1
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:01 to VLAN 0 (port 1)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:01 to VLAN 0 (port 2)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:02 to VLAN 0 (port 1)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:02 to VLAN 0 (port 2)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:16 to VLAN 0 (port 1)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:00:00:16 to VLAN 0 (port 2)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:7F:FF:FA to VLAN 0 (port 1)
 +br_register_static_mcast_mac: Add static entry 01:00:5E:7F:FF:FA to VLAN 0 (port 2)
 +[mac_0_init] ifno=1, vlan=0, vid=1, port_mask=0xf, mac_0_initialized=0
 +[init_local_variables] ethwan=2, g_eth_wan_mode=3, wanitf=0xffffffff
 +[init_local_variables] g_wan_itf=0x2, g_ipv6_acc_en=1, g_wanqos_en=8
 +[e5 alloc_dma] pre_alloc_desc_total_num=736, line 4437
 +[config_SW_VLAN] bTaggedIngress=0, bTaggedEgress=0
 +mac_0_init: interface 1 registered to VLAN 1, port_mask=f
 +MAC Address(ifno 1): 1c:c6:3c:c4:3d:a7
 +***** [iput_IpLinkUp] ifno=1, link_type:12
 +Interface 1 ip = 192.168.1.254
 +
 +gConfig.Interface[2].IP_Addr = 0.0.0.0
 +gConfig.Interface[2].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[2].Description = WLAN
 +gConfig.Interface[2].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[2].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[2].VLAN_Idx].IGMP_Querier_Enable = 1
 +[HWLAN] ifno=2 irno=7 port=0x00000000
 +***** [iput_IpLinkUp] ifno=2, link_type:12
 +Interface 2 ip = 192.168.1.254
 +
 +gConfig.Interface[3].IP_Addr = 0.0.0.0
 +gConfig.Interface[3].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[3].Description = THS
 +[mac_0_init] ifno=3, vlan=1, vid=2, port_mask=0x10, mac_0_initialized=1
 +[config_SW_VLAN] bTaggedIngress=1, bTaggedEgress=1
 +mac_0_init: interface 3 registered to VLAN 2, port_mask=10
 +MAC Address(ifno 3): 1c:c6:3c:c4:3d:a7
 +***** [iput_IpLinkUp] ifno=3, link_type:2
 +time = 08/01/2003, 00:00:00
 +iput_IpLinkUp(ifno=3)> ifp->add_default_route:1
 +Init NAT data structure
 +iput_IpLinkUp(ifno=3): set ddns_update to 1
 +Interface 3 ip = 0.0.0.0
 +
 +gConfig.Interface[4].IP_Addr = 0.0.0.0
 +gConfig.Interface[4].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[4].Description = ATM2
 +[mac_0_init] ifno=4, vlan=1, vid=2, port_mask=0x10, mac_0_initialized=1
 +[config_SW_VLAN] bTaggedIngress=1, bTaggedEgress=1
 +mac_0_init: interface 4 registered to VLAN 2, port_mask=10
 +MAC Address(ifno 4): 1c:c6:3c:c4:3d:a7
 +***** [iput_IpLinkUp] ifno=4, link_type:2
 +iput_IpLinkUp(ifno=4)> ifp->add_default_route:0
 +Init NAT data structure
 +No default route, no need to reinit the NAT data structure
 +Interface 4 ip = 0.0.0.0
 +
 +gConfig.Interface[15].IP_Addr = 0.0.0.0
 +gConfig.Interface[15].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[15].Description = PPPoE1
 +IFLNK_PPPOE init : (Linkp)ifno = 15 idx = 2
 +IFLNK_PPPOE init : (Driverp)ifno = 15 idx = 4
 +pppInit> set (PPPShutdownRequest[15] = 0), do_connect_in_progress[15]=0
 +[change_phase] start to release the allocated memory in if_table[0].ppp_p->state
 +[pppoe_init]
 +Interface 15 ip = 0.0.0.0
 +
 +gConfig.Interface[16].IP_Addr = 0.0.0.0
 +gConfig.Interface[16].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[16].Description = PPPoE2
 +IFLNK_PPPOE init : (Linkp)ifno = 16 idx = 2
 +IFLNK_PPPOE init : (Driverp)ifno = 16 idx = 4
 +pppInit> set (PPPShutdownRequest[16] = 0), do_connect_in_progress[16]=0
 +[change_phase] start to release the allocated memory in if_table[0].ppp_p->state
 +[pppoe_init]
 +[PPPoE]gInitOk==1 , So Not Do pppoe_init
 +Interface 16 ip = 0.0.0.0
 +
 +gConfig.Interface[31].IP_Addr = 0.0.0.0
 +gConfig.Interface[31].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[31].Description = WDS1
 +gConfig.Interface[31].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[31].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[31].VLAN_Idx].IGMP_Querier_Enable = 1
 +[HWLAN] ifno=31 irno=7 port=0x00000000
 +***** [iput_IpLinkUp] ifno=31, link_type:12
 +Interface 31 ip = 192.168.1.254
 +
 +gConfig.Interface[32].IP_Addr = 0.0.0.0
 +gConfig.Interface[32].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[32].Description = WDS2
 +gConfig.Interface[32].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[32].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[32].VLAN_Idx].IGMP_Querier_Enable = 1
 +[HWLAN] ifno=32 irno=7 port=0x00000000
 +***** [iput_IpLinkUp] ifno=32, link_type:12
 +Interface 32 ip = 192.168.1.254
 +
 +gConfig.Interface[33].IP_Addr = 0.0.0.0
 +gConfig.Interface[33].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[33].Description = WDS3
 +gConfig.Interface[33].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[33].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[33].VLAN_Idx].IGMP_Querier_Enable = 1
 +[HWLAN] ifno=33 irno=7 port=0x00000000
 +***** [iput_IpLinkUp] ifno=33, link_type:12
 +Interface 33 ip = 192.168.1.254
 +
 +gConfig.Interface[34].IP_Addr = 0.0.0.0
 +gConfig.Interface[34].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[34].Description = WDS4
 +gConfig.Interface[34].VLAN_Idx = 0
 +ifp->ipaddr = C0A801FE
 +ifp->netmask = FFFFFF00
 +gConfig.Vlan_Ports[gConfig.Interface[34].VLAN_Idx].VNet = 1
 +gConfig.Vlan_Ports[gConfig.Interface[34].VLAN_Idx].IGMP_Querier_Enable = 1
 +[HWLAN] ifno=34 irno=7 port=0x00000000
 +***** [iput_IpLinkUp] ifno=34, link_type:12
 +Interface 34 ip = 192.168.1.254
 +
 +gConfig.Interface[35].IP_Addr = 0.0.0.0
 +gConfig.Interface[35].Subnet_Mask = 0.0.0.0
 +gConfig.Interface[35].Description = COM1
 +pppInit> set (PPPShutdownRequest[35] = 0), do_connect_in_progress[35]=0
 +[change_phase] start to release the allocated memory in if_table[0].ppp_p->state
 +if_umts_init() WAN interface 35, UMTS-COM1: baudrate=115200
 +if_umts_init() MAC:1C:C6:3C:C4:3D:A8
 +RUNTASK id=2 umtsEventHandleTsk...
 +RUNTASK id=3 umtsEventExeHandleTsk...
 +RUNTASK id=4 umtsReceQueueTsk...
 +RUNTASK id=5 umtsReceTsk...
 +RUNTASK id=6 umtsWritTsk...
 +Interface 35 ip = 0.0.0.0
 +
 +gConfig.Interface[36].IP_Addr = 192.168.2.253
 +gConfig.Interface[36].Subnet_Mask = 255.255.255.0
 +gConfig.Interface[36].Description = APLAN
 +ruleCheck()> Group: 0,  Error: Useless rule index will be truncated, from idx:2
 +ruleCheck()> Group: 1,  Error: Useless rule index will be truncated, from idx:22
 +ruleCheck()> Group: 2,  Error: Useless rule index will be truncated, from idx:0
 +CBAC rule format check succeed !!
 +reqCBACBuf()> init match pool, Have: 1000
 +Memory Address: 0xffffffff81168514 ~ 0xffffffff8116f290
 +reqCBACBuf()> init timeGap pool, Have: 10000
 +Memory Address: 0xffffffff8116f290 ~ 0xffffffff8119ffe4
 +reqCBACBuf()> init sameHost pool, Have: 2000
 +Memory Address: 0xffffffff8119ffe4 ~ 0xffffffff811afa04
 +CBAC rule pool initialized !!
 +Init NAT data structure
 +No default route, no need to reinit the NAT data structure
 +RUNTASK id=7 if_task if0...
 +RUNTASK id=8 if_task if1...
 +RUNTASK id=9 if_task if2...
 +RUNTASK id=10 if_task if3...
 +RUNTASK id=11 if_task if4...
 +RUNTASK id=12 if_task if31...
 +RUNTASK id=13 if_task if32...
 +RUNTASK id=14 if_task if33...
 +RUNTASK id=15 if_task if34...
 +RUNTASK id=16 if_task if35...
 +RUNTASK id=17 if_task if36...
 +RUNTASK id=18 timer_task...
 +RUNTASK id=19 conn_mgr...
 +RUNTASK id=20 main_8021x...
 +RUNTASK id=21 saveRandomSeedTask...
 +vfs_codepage_init() TimeZone:23, vfs_cp_idx:23, vfs_cp_ID:5
 +fat_codePageInit() TimeZone:23, codePage:CP850, cPID:5, cpSize:256, toUpSize:30
 +==[vfs_register_filesystem]============================
 +list size:1,  Method:0x808f5cfc
 +  1) Type:0xfc, Name:BRN-VFS
 +=================================================================
 +==[vfs_register_filesystem]============================
 +list size:7,  Method:0x808f5e88
 +  1) Type:0x01, Name:FAT12
 +  2) Type:0x04, Name:FAT16
 +  3) Type:0x06, Name:FAT16
 +  4) Type:0x0b, Name:FAT32
 +  5) Type:0x0c, Name:FAT32
 +  6) Type:0x0e, Name:FAT16
 +  7) Type:0x81, Name:Minix
 +=================================================================
 +[0-START]=========================================
 +  Node 000-[\],  DIR, MountFlag:0x00
 +[0-END]===========================================
 +  [1-START]=========================================
 +    Node 001-[dev],  DIR, MountFlag:0x00
 +  [1-END]===========================================
 +  [1-START]=========================================
 +    Node 002-[mnt],  DIR, MountFlag:0x00
 +  [1-END]===========================================
 +dump_inode() freeCnt:77, usedCnt:3
 +otg_host_power_set() USB Host0 Power OFF
 +usb_host_power_set() isOn:1
 +otg_host_power_set() USB Host1 Power OFF
 +usb_host_power_set() isOn:1
 +RUNTASK id=23 period_task...
 +
 +========== ADSL Modem initialization OK ! ======
 +
 +[Dhcpd_Start]
 +RUNTASK id=24 dhcp_daemon...
 +main()> usb:1, ftp:0
 +found signature: 78h 56h 34h 12h
 +ulImgLens=2166494, LENGTH[5]-12=7864308, type:0
 +length checking OK
 +[0]2 find End at 0xFFFFFFFFB0290C00 len=2166494, type=0
 +found signature: 78h 56h 34h 12h
 +ulImgLens=6978, LENGTH[5]-12=7864308, type:10
 +length checking OK
 +[1]2 find End at 0xFFFFFFFFB0292800 len=6978, type=10
 +found signature: 78h 56h 34h 12h
 +ulImgLens=12616, LENGTH[5]-12=7864308, type:11
 +length checking OK
 +[2]2 find End at 0xFFFFFFFFB0295C00 len=12616, type=11
 +found signature: 78h 56h 34h 12h
 +ulImgLens=231260, LENGTH[5]-12=7864308, type:12
 +length checking OK
 +[3]2 find End at 0xFFFFFFFFB02CE400 len=231260, type=12
 +---[ LZMA head start in 0xFFFFFFFFB02CE800 ]---
 +found signature: 78h 56h 34h 12h
 +ulImgLens=365159, LENGTH[5]-12=7864308, type:50
 +length checking OK
 +[4]2 find End at 0xFFFFFFFFB0327800 len=365159, type=50
 +---[ LZMA head start in 0xFFFFFFFFB0327C00 ]---
 +found signature: 78h 56h 34h 12h
 +ulImgLens=363500, LENGTH[5]-12=7864308, type:90
 +length checking OK
 +[5]2 find End at 0xFFFFFFFFB0380800 len=363500, type=90
 +---[ LZMA head start in 0xFFFFFFFFB0380C00 ]---
 +found signature: 78h 56h 34h 12h
 +ulImgLens=202985, LENGTH[5]-12=7864308, type:8
 +length checking OK
 +[6]2 find End at 0xFFFFFFFFB03B2400 len=202985, type=8
 +[get_web_address] Web-0:  addr:0xb0291000, len:6978, type:10
 +[get_web_address] Web-1:  addr:0xb0292c00, len:12616, type:11
 +[get_web_address] Web-2:  addr:0xb0296000, len:231260, type:12
 +RUNTASK httpd...
 +RUNTASK id=28 SSLClient ...
 +g_Client_Cert_Array=0x81c49558
 +RUNTASK id=29 dnsproxy...
 +RUNTASK id=30 dhcpd_mgmt_task...
 +runDDNS() ddns_enable:0, DDNSTaskRun:0, needReRunDDNS:1
 +UPnP task run-up... upnpFunc:1
 +UPNP Device initialize success! slot=31
 +TR64 is enabled
 +TR64 Device initialize success! slot=32
 +RUNTASK id=35 wscmain...
 +RUNTASK id=36 wsc_Send_eap_packet...
 +RUNTASK id=37 wsc_Send_UPNP_packet...
 +RUNTASK id=38 WSC_WaitUserAction_Task...
 +UART RX Output
 +Starting Multitask...
 +
 +===== General exception ======
 +EPC  -> 0x80006F20
 +CO_SR -> 0x0000FC03
 +Register Dump: Saved Area : Begin 0x8166CC34 End 0x8166CDCF
 +RES:0x00000000
 + RA:0x8000585C
 + AT:0x809A0000
 + V0:0x80000010
 + V1:0x0000FC03
 + A0:0x00000015
 + A1:0x00000008
 + A2:0x01BC3854
 + T0:0x0000FC01
 + T1:0x00000000
 + T2:0x0000005A
 + T3:0x00000001
 + T4:0x00000000
 + T5:0x00000000
 + T6:0x0FFFFFFF
 + T7:0x0000000F
 + T8:0x808AF8F5
 + T9:0x00000000
 + S0:0x00000BB8
 + S1:0x00000015
 + S2:0x00000015
 + S3:0xFFFFFFFF
 + S4:0x00000001
 + S5:0x00000000
 + S6:0x01E02108
 + S7:0xC1838500
 + S8:0x3052E99D
 +EPC:0x80006F20
 + SR:0x0000FC03
 + CAUSE:0x80000010
 + Instruction : 0x14628821
 + SP (Save Point) :0x8166CC34
 +==============================
 +
 +===================
 +Print call path
 +0x00000000,Function=0x80006EC0  PC=0x80006F20
 +0x00000001,Function=0x8000584C  PC=0x80005854
 +0x00000002,Function=0x00000000  PC=0x80005844
 +
 +===================
 +
 +===================
 +Print call stacks
 +0x00000000 Stack:
 +0x8166CEF0: 0x00000BB8 0x00000015 0x00000064 0x80113704
 +0x8166CF00: 0x00000001 0x8000585C 0xC1838500 0x00000000
 +
 +0x00000001 Stack:
 +0x8166CF10: 0x8000584C 0x00000000 0x80113704 0x00000000
</code> </code>
Line 312: Line 890:
<p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF"> <p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF">
<code> <code>
 +
 +ROM VER: 1.0.5
 +CFG 01
 +
 +
 +U-Boot 2014.04-g1702a40-dirty (Jun 21 2014 - 16:13:24) VGV7519
 +
 +Board: Arcadyan VGV7519 VRX288 Board
 +SoC:  Lantiq VRX288 v1.1
 +CPU:  500 MHz
 +IO:    250 MHz
 +BUS:  250 MHz
 +BOOT:  NOR
 +DRAM:  64 MiB
 +Flash: 16 MiB
 +*** Warning - bad CRC, using default environment
 +
 +In:    serial
 +Out:  serial
 +Err:  serial
 +Net:  firmware: using built-in firmware lantiq/vrx200_phy11g_a1x.fw
 +ltq-eth
 +Hit any key to stop autoboot:  0
 +Wrong Image Format for bootm command
 +ERROR: can't get kernel image!
 +VGV7519 # bootm 0xB0080000
 +## Booting kernel from Legacy Image at b0080000 ...
 +  Image Name:  MIPS OpenWrt Linux-3.10.36
 +  Created:      2014-06-21  11:50:30 UTC
 +  Image Type:  MIPS Linux Kernel Image (lzma compressed)
 +  Data Size:    1414748 Bytes = 1.3 MiB
 +  Load Address: 80002000
 +  Entry Point:  80002000
 +  Verifying Checksum ... OK
 +  Uncompressing Kernel Image ... OK
Starting kernel ... Starting kernel ...
-[    0.000000] Linux version 3.8.13 (thelizard@ubuntu) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r37050) ) #31 Sat Jul 6 01:23:47 CEST 2013+[    0.000000] Linux version 3.10.36 (thelizard@ubuntu) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41296) ) #1 Sat Jun 21 13:50:23 CEST 2014
[    0.000000] SoC: VR9 rev 1.1 [    0.000000] SoC: VR9 rev 1.1
[    0.000000] bootconsole [early0] enabled [    0.000000] bootconsole [early0] enabled
Line 334: Line 947:
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
-[    0.000000] __ex_table already sorted, skipping sort +[    0.000000] Writing ErrCtl register=0007cf41 
-[    0.000000] Writing ErrCtl register=00048068 +[    0.000000] Readback ErrCtl register=0007cf41 
-[    0.000000] Readback ErrCtl register=00048068 +[    0.000000] Memory: 60476k/65536k available (3008k kernel code, 5060k reserved, 1018k data, 188k init, 0k highmem)
-[    0.000000] Memory: 61000k/65536k available (2616k kernel code, 4536k reserved, 860k data, 224k init, 0k highmem)+
[    0.000000] NR_IRQS:256 [    0.000000] NR_IRQS:256
[    0.000000] CPU Clock: 500MHz [    0.000000] CPU Clock: 500MHz
Line 348: Line 960:
[    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28 [    0.060000] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV [    0.068000] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
-[    0.084000] bio: create slab <bio-0> at 0 +[    0.072000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185] 
-[    0.088000] gpio-stp-xway 1e100bb0.stp: Init done +[    0.184000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193] 
-[    0.092000] usbcore: registered new interface driver usbfs +[    0.284000] ifx_pcie_wait_phy_link_up timeout 
-[    0.096000] usbcore: registered new interface driver hub +[    0.288000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185] 
-[    0.100000] usbcore: registered new device driver usb +[    0.400000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193] 
-[    0.104000] Switching to clocksource MIPS +[    0.500000] ifx_pcie_wait_phy_link_up timeout 
-[    0.112000] NET: Registered protocol family 2 +[    0.504000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185] 
-[    0.116000] TCP established hash table entries: 512 (order: 0, 4096 bytes) +[    0.616000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193] 
-[    0.120000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) +[    0.716000] ifx_pcie_wait_phy_link_up timeout 
-[    0.128000] TCP: Hash tables configured (established 512 bind 512) +[    0.720000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185] 
-[    0.136000] TCP: reno registered +[    0.832000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193] 
-[    0.136000] UDP hash table entries: 256 (order: 0, 4096 bytes) +[    0.932000] ifx_pcie_wait_phy_link_up timeout 
-[    0.144000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) +[    0.936000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_assert[185] 
-[    0.152000] NET: Registered protocol family 1 +[    1.048000] arch/mips/pci/ifxmips_pcie_vr9.h:pcie_device_rst_deassert[193] 
-[    0.156000] gptu: totally 6 16-bit timers/counters +[    1.148000] ifx_pcie_wait_phy_link_up timeout 
-[    0.160000] gptu: misc_register on minor 63 +[    1.152000] pcie_rc_initialize link up failed!!!!! 
-[    0.164000] gptu: succeeded to request irq 126 +[    1.164000] bio: create slab <bio-0> at 0 
-[    0.168000] gptu: succeeded to request irq 127 +[    1.168000] gpio-stp-xway 1e100bb0.stp: Init done 
-[    0.172000] gptu: succeeded to request irq 128 +[    1.172000] usbcore: registered new interface driver usbfs 
-[    0.176000] gptu: succeeded to request irq 129 +[    1.176000] usbcore: registered new interface driver hub 
-[    0.184000] gptu: succeeded to request irq 130 +[    1.180000] usbcore: registered new device driver usb 
-[    0.188000] gptu: succeeded to request irq 131 +[    1.184000] Switching to clocksource MIPS 
-[    0.192000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a1x.bin +[    1.192000] NET: Registered protocol family 2 
-[    0.200000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 38C0000 +[    1.196000] TCP established hash table entries: 512 (order: 0, 4096 bytes) 
-[    0.208000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 38C0000 +[    1.200000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) 
-[    0.316000] squashfs: version 4.0 (2009/01/31) Phillip Lougher +[    1.208000] TCP: Hash tables configured (established 512 bind 512) 
-[    0.320000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. +[    1.216000] TCP: reno registered 
-[    0.332000] msgmni has been set to 119 +[    1.216000] UDP hash table entries: 256 (order: 0, 4096 bytes) 
-[    0.336000] io scheduler noop registered +[    1.224000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) 
-[    0.340000] io scheduler deadline registered (default) +[    1.232000] NET: Registered protocol family 1 
-[    0.344000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc +[    1.236000] gptu: totally 6 16-bit timers/counters 
-[    0.352000] console [ttyLTQ0] enabled, bootconsole disabled +[    1.240000] gptu: misc_register on minor 63 
-[    0.352000] console [ttyLTQ0] enabled, bootconsole disabled +[    1.244000] gptu: succeeded to request irq 126 
-[    0.368000] lantiq nor flash device: 00800000 at 10000000 +[    1.248000] gptu: succeeded to request irq 127 
-[    0.372000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00007f Chip ID 0x0022cb +[    1.252000] gptu: succeeded to request irq 128 
-[    0.380000] Amd/Fujitsu Extended Query Table at 0x0040 +[    1.256000] gptu: succeeded to request irq 129 
-[    0.384000]  Amd/Fujitsu Extended Query version 1.1. +[    1.264000] gptu: succeeded to request irq 130 
-[    0.392000] number of CFI chips: 1 +[    1.268000] gptu: succeeded to request irq 131 
-[    0.392000] lantiq nor flash device: 00800000 at 14800000 +[    1.272000] phy-xrx200 gphy-xrx200.5: requesting lantiq/vr9_phy11g_a1x.bin 
-[    0.400000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00007f Chip ID 0x0022cb +[    1.280000] phy-xrx200 gphy-xrx200.5: booting GPHY0 firmware at 38C0000 
-[    0.408000] Amd/Fujitsu Extended Query Table at 0x0040 +[    1.288000] phy-xrx200 gphy-xrx200.5: booting GPHY1 firmware at 38C0000 
-[    0.412000]  Amd/Fujitsu Extended Query version 1.1. +[    1.396000] squashfs: version 4.0 (2009/01/31) Phillip Lougher 
-[    0.420000] number of CFI chips: 1 +[    1.404000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 
-[    0.424000] Concatenating MTD devices: +[    1.412000] msgmni has been set to 118 
-[    0.428000] (0): "ltq_nor" +[    1.416000] io scheduler noop registered 
-[    0.428000] (1): "ltq_nor" +[    1.420000] io scheduler deadline registered (default) 
-[    0.432000] into device "10000000.nor-boot" +[    1.428000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,asc 
-[    0.436000] 3 ofpart partitions found on MTD device 10000000.nor-boot +[    1.436000] console [ttyLTQ0] enabled, bootconsole disabled 
-[    0.444000] Creating 3 MTD partitions on "10000000.nor-boot": +[    1.436000] console [ttyLTQ0] enabled, bootconsole disabled 
-[    0.448000] 0x000000000000-0x000000040000 : "uboot" +[    1.448000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00007f Chip ID 0x0022cb 
-[    0.456000] 0x000000060000-0x000000070000 : "uboot_env" +[    1.456000] Amd/Fujitsu Extended Query Table at 0x0040 
-[    0.460000] 0x000000080000-0x000001000000 : "linux+[    1.464000]  Amd/Fujitsu Extended Query version 1.1. 
-[    0.464000] Creating 2 MTD partitions on "10000000.nor-boot"+[    1.468000] number of CFI chips: 1 
-[    0.468000] 0x000000080000-0x0000001b0000 : "kernel+[    1.472000] 3 ofpart partitions found on MTD device ltq_nor 
-[    0.476000] 0x0000001b0000-0x000001000000 : "rootfs" +[    1.476000] Creating 3 MTD partitions on "ltq_nor": 
-[    0.480000] mtd: partition "rootfs" set to be root filesystem +[    1.480000] 0x000000000000-0x000000040000 : "uboot" 
-[    0.484000] mtd: partition "rootfs_data" created automatically, ofs=390000, len=C70000 +[    1.488000] 0x000000060000-0x000000070000 : "uboot_env" 
-[    0.492000] 0x000000390000-0x000001000000 : "rootfs_data" +[    1.492000] 0x000000080000-0x000001000000 : "firmware
-[    0.608000] libphy: lantiq,xrx200-mdio: probed +[    1.496000] mtd: partition "firmware" extends beyond the end of device "ltq_nor" -- size truncated to 0x780000 
-[    0.616000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1) +[    1.508000] 0x0000001d969c-0x000000800000 : "rootfs" 
-[    0.624000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1) +[    1.512000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only 
-[    0.632000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1) +[    1.528000] mtd: device 3 (rootfs) set to be root filesystem 
-[    0.636000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1) +[    1.532000] mtd: partition "rootfs_data" created automatically, ofs=0x3f0000, len=0x410000 
-[    0.648000] eth1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1) +[    1.540000] 0x0000003f0000-0x000000800000 : "rootfs_data" 
-[    0.656000] wdt 1f8803f0.watchdog: Init done +[    1.672000] libphy: lantiq,xrx200-mdio: probed 
-[    0.660000] leds-gpio gpio-leds.7: pins are not configured from the driver +[    1.680000] net-xrx200: invalid MAC, using random 
-[    0.668000] TCP: cubic registered +[    1.684000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:00, irq=-1) 
-[    0.672000] NET: Registered protocol family 17 +[    1.692000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:01, irq=-1) 
-[    0.676000] 8021q: 802.1Q VLAN Support v1.8 +[    1.700000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1) 
-[    0.688000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4+[    1.708000] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1) 
-[    0.696000] Freeing unused kernel memory: 224k freed+[    1.716000] net-xrx200: invalid MAC, using random 
 +[    1.720000] eth1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.3] (phy_addr=0:05, irq=-1) 
 +[    1.728000] wdt 1f8803f0.watchdog: Init done 
 +[    1.732000] leds-gpio gpio-leds.7: pins are not configured from the driver 
 +[    1.744000] TCP: cubic registered 
 +[    1.744000] NET: Registered protocol family 17 
 +[    1.752000] 8021q: 802.1Q VLAN Support v1.8 
 +[    1.760000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19 
 +[    1.772000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3
 +[    1.776000] Freeing unused kernel memory: 188K (803f1000 - 80420000) 
 +[    2.700000] eth0: port 0 got link
procd: Console is alive procd: Console is alive
-[    2.260000] IFXUSB: ifxusb_hcd: version 3.2 B110801 +procd: - watchdog - 
-[    2.264000] Chip Version :01c0 BurstSize=0 +[    4.572000] IFXUSB: ifxusb_hcd: version 3.2 B110801 
-[    2.868000] IFXUSB: USB core #0 soft-reset +[    4.576000] Chip Version :01c0 BurstSize=0 
-[    3.168000] IFXUSB: USB core #0 soft-reset +[    5.180000] IFXUSB: USB core #0 soft-reset 
-[    3.172000] ifxusb_hcd ifxusb_hcd: IFX USB Controller +[    5.484000] IFXUSB: USB core #0 soft-reset 
-[    3.176000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1 +[    5.488000] ifxusb_hcd ifxusb_hcd: IFX USB Controller 
-[    3.184000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000 +[    5.492000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 1 
-[    3.188000] IFXUSB: Init: Power Port (0) +[    5.500000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000 
-[    3.196000] eth0: port 4 got link +[    5.504000] IFXUSB: Init: Power Port (0) 
-[    3.196000] hub 1-0:1.0: USB hub found +[    5.512000] hub 1-0:1.0: USB hub found 
-[    3.200000] hub 1-0:1.0: 1 port detected +[    5.512000] hub 1-0:1.0: 1 port detected 
-[    3.704000] IFXUSB: USB core #1 soft-reset +[    6.016000] IFXUSB: USB core #1 soft-reset 
-[    4.008000] IFXUSB: USB core #1 soft-reset +[    6.320000] IFXUSB: USB core #1 soft-reset 
-[    4.012000] ifxusb_hcd ifxusb_hcd: IFX USB Controller +[    6.324000] ifxusb_hcd ifxusb_hcd: IFX USB Controller 
-[    4.016000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2 +[    6.328000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 2 
-[    4.024000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000 +[    6.336000] ifxusb_hcd ifxusb_hcd: irq 91, io mem 0xbe106000 
-[    4.028000] IFXUSB: Init: Power Port (0) +[    6.340000] IFXUSB: Init: Power Port (0) 
-[    4.032000] hub 2-0:1.0: USB hub found +[    6.344000] hub 2-0:1.0: USB hub found 
-[    4.036000] hub 2-0:1.0: 1 port detected +[    6.348000] hub 2-0:1.0: 1 port detected 
-[    4.040000] ifxusb_hcd ifxusb_hcd: requested GPIO 233+[    6.352000] ifxusb_hcd ifxusb_hcd: requested GPIO 232
procd: - preinit - procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode Press the [f] key and hit [enter] to enter failsafe mode
-mount_root: jffs2 is ready +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level 
-[    7.464000] jffs2: notice: (257) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 8 of xref (0 dead, 2 orphan) found.+jffs2 is ready 
 +jffs2 is ready 
 +[    9.832000] jffs2: notice: (267) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 9 of xref (0 dead, 2 orphan) found. 
 +switching to overlay
procd: - early - procd: - early -
procd: - watchdog - procd: - watchdog -
 +procd: - ubus -
procd: - init - procd: - init -
Please press Enter to activate this console. Please press Enter to activate this console.
-[   8.952000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH+[   11.252000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
-[   9.100000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5 +11.276000] NET: Registered protocol family 10 
-[    9.104000] Backport generated by backports.git backports-20130617-4-ge3220f5 +11.284000] NET: Registered protocol family 8 
-[    9.140000] cfg80211: Calling CRDA to update world regulatory domain +11.288000] NET: Registered protocol family 20 
-[    9.148000] cfg80211: World regulatory domain updated: +11.300000] sit: IPv6 over IPv4 tunneling driver 
-[    9.152000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) +[  11.316000] PPP generic driver version 2.4.2 
-[    9.160000] cfg80211:  (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) +11.336000] nf_conntrack version 0.5.0 (947 buckets, 3788 max) 
-[    9.164000] cfg80211:  (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) +[  11.352000] ip6_tables: (C) 2000-2006 Netfilter Core Team 
-[    9.172000] cfg80211:  (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) +[  11.388000] MEI CPE Driver, Version 1.2.0
-[    9.180000] cfg80211:  (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) +
-[    9.188000] cfg80211:  (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) +
-[    9.428000] NET: Registered protocol family 10 +
-10.144000] NET: Registered protocol family 8 +
-10.148000] NET: Registered protocol family 20 +
-10.220000] PPP generic driver version 2.4.2 +
-10.460000] ip_tables: (C) 2000-2006 Netfilter Core Team +
-[  10.540000] xt_time: kernel timezone is -0000 +
-[  10.552000] NET: Registered protocol family 24 +
-[  10.636000] nf_conntrack version 0.5.0 (956 buckets, 3824 max) +
-[  11.116000] ip6_tables: (C) 2000-2006 Netfilter Core Team +
-[  11.148000] MEI CPE Driver, Version 1.2.0+
-[  11.148000] (c) Copyright 2009, Infineon Technologies AG+[  11.392000] (c) Copyright 2009, Infineon Technologies AG
### MEI CPE - MEI CPE - MEI CPE - MEI CPE ### ### MEI CPE - MEI CPE - MEI CPE - MEI CPE ###
Lantiq CPE API Driver version: DSL CPE API V4.11.4 Lantiq CPE API Driver version: DSL CPE API V4.11.4
-[  11.240000+[  11.420000
-[  11.240000] Predefined debug level: 2 +[  11.420000] Predefined debug level: 2 
-[  11.352000] ATM1.0.26    ATM (A1) firmware version 0.24 +[  11.428000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea 
-[  11.356000] ifxmips_atm: ATM init succeed +[  11.436000] Backport generated by backports.git backports-20140320-37-g5c33da0 
-[  11.476000] Infineon Technologies DEU driver version 2.0.0 +[  11.444000] ip_tables: (C) 2000-2006 Netfilter Core Team 
-[  11.480000] IFX DEU DES initialized (multiblock). +[  11.456000] Infineon Technologies DEU driver version 2.0.0 
-[  11.484000] IFX DEU AES initialized (multiblock). +[  11.460000] IFX DEU DES initialized (multiblock). 
-[  11.488000] IFX DEU ARC4 initialized (multiblock). +[  11.468000] IFX DEU AES initialized (multiblock). 
-[  11.496000] IFX DEU SHA1 initialized. +[  11.472000] IFX DEU ARC4 initialized (multiblock). 
-[  11.496000] IFX DEU MD5 initialized. +[  11.476000] IFX DEU SHA1 initialized. 
-[  11.500000] IFX DEU SHA1_HMAC initialized. +[  11.480000] IFX DEU MD5 initialized. 
-[  11.504000] IFX DEU MD5_HMAC initialized. +[  11.484000] IFX DEU SHA1_HMAC initialized. 
-15.360000] device eth0 entered promiscuous mode +[  11.488000] IFX DEU MD5_HMAC initialized. 
-15.364000] br-lan: port 1(eth0) entered forwarding state +11.508000] NET: Registered protocol family 24 
-15.372000] br-lan: port 1(eth0) entered forwarding state +[  11.528000] xt_time: kernel timezone is -0000 
-17.376000] br-lan: port 1(eth0) entered forwarding state+[  11.552000] cfg80211: Calling CRDA to update world regulatory domain 
 +[  11.556000] cfg80211: World regulatory domain updated: 
 +[  11.560000] cfg80211:  DFS Master region: unset 
 +[  11.564000] cfg80211:  (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) 
 +[  11.576000] cfg80211:  (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  11.584000] cfg80211:  (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  11.592000] cfg80211:  (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  11.600000] cfg80211:  (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  11.608000] cfg80211:  (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) 
 +[  11.616000] cfg80211:  (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) 
 +[  18.052000] device eth0 entered promiscuous mode 
 +18.060000] br-lan: port 1(eth0) entered forwarding state 
 +18.064000] br-lan: port 1(eth0) entered forwarding state 
 +20.068000] br-lan: port 1(eth0) entered forwarding state
procd: - init complete - procd: - init complete -
Line 498: Line 1125:
</HTML> </HTML>
 +===== Progress =====
 +
 +|USB: working  |https://dev.openwrt.org/ticket/16800#ticket  |
 +|WIFI: working |https://dev.openwrt.org/changeset/42907 (CC) |
 +|              |https://dev.openwrt.org/changeset/42906 (BB) |
 +             
===== Notes ===== ===== Notes =====
 +SIP:
 +
 +daemon to test:
 +sofia-sip
 +pjsip(already in openwrt)
 +owsip(already in openwrt)
 +
 +driver vmmc:
 +http://mirror2.openwrt.org/sources/drv_vmmc-1.9.0.tar.bz2
 +drv_vmmc-1.9.0/FEATURES_and_OPEN_ISSUES
 +* TAPI 3.13.0.2, drv_vmmc 1.9.0.3, KPI 2.2.0.0, MPS 2.2.2.5
 +* XWAY VRX288 VoIP Firmware  2.1.0.7.0
 +Original firmware 1.9.0.4
 +
 +need firmware dump for dsl, voip and coef + populate openwrt/package/ifx-vmmc/Makefile
 +
 +driver tapi:
 +http://mirror2.openwrt.org/sources/drv_tapi-3.13.0.tar.bz2
 +Same level as original firmware
 +
 +http://dev.phrozen.org/ltq-mirror/ (dsl and other stuff)
 +
 +DSL:
 +available version 4.11.4 - my firmware version: 4.12.4 - May works
 +need firmware dump
 +
 +SWITCH:
 +look at switch_utils note at http://wiki.openwrt.org/toh/tp-link/td-w8970#switch_utility
 +we need to decompile original firmware and recovery switch initialization params
 +
 +FXO:
 +Si3050+Si3011 should be a FXO interface. It seems they implemented FXO using external component.
 +
 +WIFI:
 +I haven't decapped the shield, but by looking to original SuperTask firmware, it seems to be RT3090 Minipci + NICInitRT5390RF
===== Tags ===== ===== Tags =====
For some Help with the Tags, please have a look here: [[meta/tags]] For some Help with the Tags, please have a look here: [[meta/tags]]
-{{tag>GigabitEthernet 4Port 1NIC 1WNIC USB 2USB ath9k 64RAM 16Flash MIPS MIPS32 34K lantiq VR9 VDSL2}}+{{tag>GigabitEthernet 4Port 1NIC 1WNIC USB 2USB ath9k 64RAM 16Flash MIPS MIPS32 34K lantiq VR9 VDSL2 JTAG}}

Back to top

toh/arcadyan/vgv7519.1373190538.txt.bz2 · Last modified: 2013/07/07 11:48 (external edit)