Differences

This shows you the differences between two versions of the page.

toh:astoria:arv752dpw22 [2014/02/17 15:38]
toh:astoria:arv752dpw22 [2014/10/05 21:13] (current)
dsdwn
Line 2981: Line 2981:
===== U-Boot ===== ===== U-Boot =====
-Downloads: [[http://downloads.openwrt.org/snapshots/trunk/lantiq/|OpenWrt Trunk uboot]]+Downloads: [[http://downloads.openwrt.org/attitude_adjustment/12.09-rc1/lantiq/danube/|OpenWrt 12.09-rc1 uboot]]
There are 3 different possibilities to run u-boot: There are 3 different possibilities to run u-boot:
Line 2988: Line 2988:
  - **uboot-lantiq-arv752DPW22_ramboot** meant to be uploaded via UART by the cpu if flash's bootloader is broken, for rescue purposes \\ see [[arv752dpw22#uart.mode|below]]   - **uboot-lantiq-arv752DPW22_ramboot** meant to be uploaded via UART by the cpu if flash's bootloader is broken, for rescue purposes \\ see [[arv752dpw22#uart.mode|below]]
 +More recent version of U-Boot available for this device [[http://downloads.openwrt.org/snapshots/trunk/lantiq/|from current trunk]]: Use U-Boot for ARV7518PW according to [[https://forum.openwrt.org/viewtopic.php?pid=225575#p225575|this article]].
==== run u-boot noninvasive via serial port ==== ==== run u-boot noninvasive via serial port ====
-  - download [[http://downloads.openwrt.org/snapshots/trunk/lantiq/uboot-lantiq-arv752DPW22_brnboot/|u-boot.bin]]+  - download [[http://downloads.openwrt.org/attitude_adjustment/12.09-rc1/lantiq/danube/uboot-lantiq-arv752DPW22_brnboot/u-boot.bin|u-boot.bin]]
  - get into administrative mode of bootloader   - get into administrative mode of bootloader
  - choose\\ ''[M] Upload to Memory''\\ at default address 0x80002000   - choose\\ ''[M] Upload to Memory''\\ at default address 0x80002000
Line 3079: Line 3080:
{{:toh:astoria:uart.3.3v.803a.jpg?250|}} {{:toh:astoria:uart.3.3v.803a.jpg?250|}}
{{:toh:astoria:uart.closeup.803a.jpg?250|}} {{:toh:astoria:uart.closeup.803a.jpg?250|}}
 +
 +
 +===== Running CC =====
 +
 +
 +1. compile firmware- AND u-boot-loader-images (find recipes galore in this Wiki)
 +
 +2. transfer new uboot into memory (find informations above - my example assumes, that's a running u-boot on the system avail)
 +
 +3. write new uboot to flash
 +
 +-REBOOT-
 +
 +4. load new firmware into memory (tftp or bootp)
 +
 +5. write uploaded firmware into flash (checksums may differ, addresses should be similiar)
 +
 +-REBOOT-
 +
 +
 +<code>
 +
 +HostPC:~# python ./ubootwrite.py --addr=0x80500000 --write=openwrt-lantiq-arv752dpw22_nor-u-boot.img --verbose
 +... ... ...
 +Ok, prompt received
 +Writing: mw 8052d4e0 ffffffff at: 0x8052d4e0
 +Waiting for prompt...
 +Ok, prompt received
 +File successfully written. You should run command 'crc32 80500000 0002d4e4' on the modem and the result must be 17ceed2d.
 +HostPC:~#
 +
 +
 +
 +
 +
 +#################### from serial-console ###############################################
 +
 +crc32 80500000 0002d4e4
 +
 +##### check ! (17ceed2d in my case)
 +
 +protect off 0xb0000000 0xB002FFFF   
 + 
 +erase 0xb0000000 0xB002FFFF
 +
 +cp.b 0x80500000 0xb0000000 0x2d4e4
 +
 +protect on 0xb0000000 0xB002FFFF 
 +
 +
 +
 +
 +#####################  REBOOT  ##################################
 +
 +
 +
 +
 +
 +
 +ARV752DPW22 # help
 +?      - alias for 'help'
 +base    - print or set address offset
 +bdinfo  - print Board Info structure
 +bootm  - boot application image from memory
 +bootp  - boot image via network using BOOTP/TFTP protocol
 +cmp    - memory compare
 +cp      - memory copy
 +crc32  - checksum calculation
 +editenv - edit environment variable
 +env    - environment handling commands
 +erase  - erase FLASH memory
 +exit    - exit script
 +false  - do nothing, unsuccessfully
 +flinfo  - print FLASH memory information
 +go      - start application at address 'addr'
 +help    - print command description/usage
 +iminfo  - print header information for application image
 +loadb  - load binary file over serial line (kermit mode)
 +loadx  - load binary file over serial line (xmodem mode)
 +loady  - load binary file over serial line (ymodem mode)
 +loop    - infinite loop on address range
 +md      - memory display
 +mdio    - MDIO utility commands
 +mii    - MII utility commands
 +mm      - memory modify (auto-incrementing address)
 +mw      - memory write (fill)
 +nm      - memory modify (constant address)
 +ping    - send ICMP ECHO_REQUEST to network host
 +printenv- print environment variables
 +protect - enable or disable FLASH write protection
 +reset  - Perform RESET of the CPU
 +run    - run commands in an environment variable
 +saveenv - save environment variables to persistent storage
 +setenv  - set environment variables
 +showvar - print local hushshell variables
 +test    - minimal test like /bin/sh
 +tftpboot- boot image via network using TFTP protocol
 +true    - do nothing, successfully
 +version - print monitor, compiler and linker version
 +ARV752DPW22 # version
 +
 +U-Boot 2013.10-openwrt4 (Oct 05 2014 - 01:17:14) ARV752DPW22
 +mips-openwrt-linux-uclibc-gcc (OpenWrt/Linaro GCC 4.8-2014.04 r42701) 4.8.3
 +GNU ld (GNU Binutils) 2.22
 +
 +
 +ARV752DPW22 # printenv
 +addconsole=setenv bootargs $bootargs console=$consoledev,$baudrate
 +addeth=setenv bootargs $bootargs ethaddr=$ethaddr
 +addip=setenv bootargs $bootargs ip=$ipaddr:$serverip::::$netdev:off
 +addmachtype=setenv bootargs $bootargs machtype=ARV752DPW22
 +baudrate=115200
 +bootcmd=bootm ${kernel_addr}
 +bootdelay=2
 +consoledev=ttyLTQ1
 +ethact=ltq-eth
 +ethaddr=00:01:02:03:04:05
 +ipaddr=192.168.1.1
 +kernel_addr=0xB0040000
 +load-uboot-nor=tftpboot u-boot.bin
 +load-uboot-norspl=tftpboot u-boot.ltq.norspl
 +load-uboot-norspl-lzma=tftpboot u-boot.ltq.lzma.norspl
 +load-uboot-norspl-lzo=tftpboot u-boot.ltq.lzo.norspl
 +loadaddr=0x81000000
 +netdev=eth0
 +serverip=192.168.1.2
 +stderr=serial
 +stdin=serial
 +stdout=serial
 +update-uboot-nor=run load-uboot-nor write-uboot-nor
 +write-uboot-nor=protect off 0xB0000000 +$filesize && erase 0xB0000000 +$filesize && cp.b $fileaddr 0xB0000000 $filesize
 +
 +
 +
 +ARV752DPW22 # bootp
 +BOOTP broadcast 1
 +Using ltq-eth device
 +TFTP from server 192.168.1.50; our IP address is 192.168.1.21
 +Filename 'openwrt-lantiq-xway-ARV752DPW22-squashfs.image'.
 +Load address: 0x81000000
 +Loading: #################################################################
 +        #################################################################
 +        #################################################################
 +        #################################################################
 +        #################################################################
 +        #################################################################
 +        #################################################################
 +        #################################################################
 +        #################################################################
 +        #################################################################
 +        #################################################################
 +        #################################################################
 +        #################################################################
 +        ##########################
 +        935.5 KiB/s
 +done
 +Bytes transferred = 4456452 (440004 hex)
 +ARV752DPW22 # crc32 81000000 440004
 +CRC32 for 81000000 ... 81440003 ==> 6b5cb0b5
 +
 +ARV752DPW22 # flinfo
 +
 +Bank # 1: CFI conformant flash (16 x 16)  Size: 8 MB in 135 Sectors
 +  AMD Standard command set, Manufacturer ID: 0xC2, Device ID: 0x22CB
 +  Erase timeout: 16384 ms, write timeout: 1 ms
 +
 +  Sector Start Addresses:
 +  B0000000  RO  B0002000  RO  B0004000  RO  B0006000  RO  B0008000  RO
 +  B000A000  RO  B000C000  RO  B000E000  RO  B0010000  RO  B0020000  RO
 +  B0030000  RO  B0040000        B0050000        B0060000        B0070000     
 +  B0080000        B0090000        B00A0000        B00B0000        B00C0000     
 +  B00D0000        B00E0000        B00F0000        B0100000        B0110000     
 +  B0120000        B0130000        B0140000        B0150000        B0160000     
 +  B0170000        B0180000        B0190000        B01A0000        B01B0000     
 +  B01C0000        B01D0000        B01E0000        B01F0000        B0200000     
 +  B0210000        B0220000        B0230000        B0240000        B0250000     
 +  B0260000        B0270000        B0280000        B0290000        B02A0000     
 +  B02B0000        B02C0000        B02D0000        B02E0000        B02F0000     
 +  B0300000        B0310000        B0320000        B0330000        B0340000     
 +  B0350000        B0360000        B0370000        B0380000        B0390000     
 +  B03A0000        B03B0000        B03C0000        B03D0000        B03E0000     
 +  B03F0000        B0400000        B0410000        B0420000        B0430000     
 +  B0440000        B0450000        B0460000        B0470000        B0480000     
 +  B0490000        B04A0000        B04B0000        B04C0000        B04D0000     
 +  B04E0000        B04F0000        B0500000        B0510000        B0520000     
 +  B0530000        B0540000        B0550000        B0560000        B0570000     
 +  B0580000        B0590000        B05A0000        B05B0000        B05C0000     
 +  B05D0000        B05E0000        B05F0000        B0600000        B0610000     
 +  B0620000        B0630000        B0640000        B0650000        B0660000     
 +  B0670000        B0680000        B0690000        B06A0000        B06B0000     
 +  B06C0000        B06D0000        B06E0000        B06F0000        B0700000     
 +  B0710000        B0720000        B0730000        B0740000        B0750000     
 +  B0760000        B0770000        B0780000        B0790000        B07A0000     
 +  B07B0000        B07C0000        B07D0000        B07E0000        B07F0000     
 +
 +ARV752DPW22 # erase 0xB0040000 0xB048FFFF
 +
 +..................................................................... done
 +Erased 69 sectors
 +ARV752DPW22 # cp.b 0x81000000 0xB0040000 0x440004
 +Copy to Flash... done
 +
 +#####################  REBOOT  ##################################
 +
 +
 +ARV752DPW22 #
 +ROM VER: 1.0.3
 +CFG 01
 +ReaƤ
 +ROM VER: 1.0.3
 +CFG 01
 +Read EEPROMX
 + X
 +
 +
 +U-Boot 2013.10-openwrt4 (Oct 05 2014 - 01:17:14) ARV752DPW22
 +
 +Board: Arcadyan ARV752DPW22
 +SoC:  Lantiq Danube-S v1.5
 +CPU:  333.333 MHz
 +IO:    166.667 MHz
 +BUS:  83.333 MHz
 +BOOT:  NOR
 +DRAM:  64 MiB
 +Flash: 8 MiB
 +In:    serial
 +Out:  serial
 +Err:  serial
 +Net:  ltq-eth
 +Hit any key to stop autoboot:  0
 +## Booting kernel from Legacy Image at b0040000 ...
 +  Image Name:  MIPS OpenWrt Linux-3.14.18
 +  Created:      2014-10-05  0:48:52 UTC
 +  Image Type:  MIPS Linux Kernel Image (lzma compressed)
 +  Data Size:    1442704 Bytes = 1.4 MiB
 +  Load Address: 80002000
 +  Entry Point:  80002000
 +  Verifying Checksum ... OK
 +  Uncompressing Kernel Image ... OK
 +
 +Starting kernel ...
 +
 +[    0.000000] Linux version 3.14.18 (zeissig@deb9470m) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r42701) ) #1 Sun Oct 5 01:48:43 BST 2014
 +[    0.000000] SoC: Danube rev 1.5
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU0 revision is: 00019641 (MIPS 24KEc)
 +[    0.000000] MIPS: machine is ARV752DPW22 - Arcor 803
 +[    0.000000] Determined physical RAM map:
 +[    0.000000]  memory: 04000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone ranges:
 +[    0.000000]  Normal  [mem 0x00000000-0x03ffffff]
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000]  node  0: [mem 0x00000000-0x03ffffff]
 +[    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes.
 +[    0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Writing ErrCtl register=0007a008
 +[    0.000000] Readback ErrCtl register=0007a008
 +[    0.000000] Memory: 60484K/65536K available (3166K kernel code, 144K rwdata, 720K rodata, 176K init, 190K bss, 5052K reserved)
 +[    0.000000] NR_IRQS:256
 +[    0.000000] CPU Clock: 333MHz
 +[    0.000000] Calibrating delay loop... 221.18 BogoMIPS (lpj=442368)
 +[    0.036000] pid_max: default: 32768 minimum: 301
 +[    0.040000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.044000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.052000] pinctrl core: initialized pinctrl subsystem
 +[    0.056000] NET: Registered protocol family 16
 +[    0.076000] pinctrl-xway 1e100b10.pinmux: Init done
 +[    0.080000] dma-xway 1e104100.dma: Init done - hw rev: 3, ports: 5, channels: 20
 +[    0.092000] PCI host bridge /fpi@10000000/pci@E105400 ranges:
 +[    0.096000]  MEM 0x0000000018000000..0x0000000019ffffff
 +[    0.100000]  IO 0x000000001ae00000..0x000000001affffff
 +[    0.124000] bio: create slab <bio-0> at 0
 +[    0.136000] usbcore: registered new interface driver usbfs
 +[    0.140000] usbcore: registered new interface driver hub
 +[    0.144000] usbcore: registered new device driver usb
 +[    0.148000] PCI host bridge to bus 0000:00
 +[    0.152000] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
 +[    0.156000] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
 +[    0.160000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
 +[    0.168000] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff]
 +[    0.172000] pci 0000:00:0f.2: BAR 0: assigned [mem 0x18010000-0x180100ff]
 +[    0.176000] pci 0000:00:0f.0: BAR 4: assigned [io  0x1ae00000-0x1ae0001f]
 +[    0.180000] pci 0000:00:0f.1: BAR 4: assigned [io  0x1ae00020-0x1ae0003f]
 +[    0.184000] Switched to clocksource MIPS
 +[    0.196000] NET: Registered protocol family 2
 +[    0.200000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.208000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.212000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.220000] TCP: reno registered
 +[    0.224000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.228000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.236000] NET: Registered protocol family 1
 +[    0.240000] PCI: Enabling device 0000:00:0f.0 (0000 -> 0001)
 +[    0.248000] PCI: Enabling device 0000:00:0f.1 (0000 -> 0001)
 +[    0.252000] PCI: Enabling device 0000:00:0f.2 (0000 -> 0002)
 +[    0.260000] gptu: totally 6 16-bit timers/counters
 +[    0.264000] gptu: misc_register on minor 63
 +[    0.268000] gptu: succeeded to request irq 126
 +[    0.272000] gptu: succeeded to request irq 127
 +[    0.276000] gptu: succeeded to request irq 128
 +[    0.280000] gptu: succeeded to request irq 129
 +[    0.288000] gptu: succeeded to request irq 130
 +[    0.292000] gptu: succeeded to request irq 131
 +[    0.304000] lantiq,vmmc 1f103000.vmmc: requested GPIO 209
 +[    0.308000] lantiq,vmmc 1f103000.vmmc: reserved 1MB at 0x03900000
 +[    0.316000] ralink,eeprom ralink_eep.4: using RT2860.eeprom as eeprom
 +[    0.328000] futex hash table entries: 256 (order: -1, 3072 bytes)
 +[    0.336000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +[    0.340000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.352000] msgmni has been set to 118
 +[    0.356000] io scheduler noop registered
 +[    0.360000] io scheduler deadline registered (default)
 +[    0.368000] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
 +[    0.376000] console [ttyLTQ0] enabled
 +[    0.376000] console [ttyLTQ0] enabled
 +[    0.384000] bootconsole [early0] disabled
 +[    0.384000] bootconsole [early0] disabled
 +[    0.396000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
 +[    0.404000] Amd/Fujitsu Extended Query Table at 0x0040
 +[    0.408000]  Amd/Fujitsu Extended Query version 1.1.
 +[    0.416000] number of CFI chips: 1
 +[    0.416000] 4 ofpart partitions found on MTD device ltq_nor
 +[    0.424000] Creating 4 MTD partitions on "ltq_nor":
 +[    0.428000] 0x000000000000-0x000000030000 : "uboot"
 +[    0.436000] 0x000000030000-0x000000040000 : "uboot_env"
 +[    0.444000] 0x000000040000-0x0000007f0000 : "firmware"
 +[    0.460000] 2 uimage-fw partitions found on MTD device firmware
 +[    0.464000] 0x000000040000-0x0000001a03d0 : "kernel"
 +[    0.472000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    0.488000] 0x0000001a03d0-0x0000007f0000 : "rootfs"
 +[    0.488000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    0.504000] mtd: device 4 (rootfs) set to be root filesystem
 +[    0.508000] mtd: partition "rootfs_data" created automatically, ofs=0x450000, len=0x3a0000
 +[    0.516000] 0x000000450000-0x0000007f0000 : "rootfs_data"
 +[    0.572000] 0x0000007f0000-0x000000800000 : "board_config"
 +[    0.616000] switch0: Atheros AR8216 rev. 1 switch registered on 1e180000.etop-ff
 +[    0.652000] libphy: ltq_mii: probed
 +[    0.812000] eth0: attached PHY [Atheros AR8216/AR8236/AR8316] (phy_addr=1e180000.etop-ff:00, irq=-1)
 +[    0.824000] wdt 1f8803f0.watchdog: Init done
 +[    0.840000] TCP: cubic registered
 +[    0.844000] NET: Registered protocol family 17
 +[    0.848000] 8021q: 802.1Q VLAN Support v1.8
 +[    0.860000] UBIFS error (pid 1): ubifs_mount: cannot open "ubi0:rootfs", error -19
 +[    0.876000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
 +[    0.884000] Freeing unused kernel memory: 176K (803f4000 - 80420000)
 +procd: Console is alive
 +procd: - watchdog -
 +[    6.228000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 +[    6.232000] ehci-platform: EHCI generic platform driver
 +[    6.240000] ehci-pci: EHCI PCI platform driver
 +[    6.244000] ehci-pci 0000:00:0f.2: EHCI Host Controller
 +[    6.248000] ehci-pci 0000:00:0f.2: new USB bus registered, assigned bus number 1
 +[    6.256000] ehci-pci 0000:00:0f.2: irq 135, io mem 0x18010000
 +[    6.272000] ehci-pci 0000:00:0f.2: USB 2.0 started, EHCI 1.00
 +[    6.276000] hub 1-0:1.0: USB hub found
 +[    6.280000] hub 1-0:1.0: 4 ports detected
 +[    6.288000] uhci_hcd: USB Universal Host Controller Interface driver
 +[    6.292000] uhci_hcd 0000:00:0f.0: UHCI Host Controller
 +[    6.300000] uhci_hcd 0000:00:0f.0: new USB bus registered, assigned bus number 2
 +[    6.304000] uhci_hcd 0000:00:0f.0: irq 135, io base 0x1ae00000
 +[    6.312000] hub 2-0:1.0: USB hub found
 +[    6.316000] hub 2-0:1.0: 2 ports detected
 +[    6.320000] uhci_hcd 0000:00:0f.1: UHCI Host Controller
 +[    6.324000] uhci_hcd 0000:00:0f.1: new USB bus registered, assigned bus number 3
 +[    6.332000] uhci_hcd 0000:00:0f.1: irq 135, io base 0x1ae00020
 +[    6.340000] hub 3-0:1.0: USB hub found
 +[    6.344000] hub 3-0:1.0: 2 ports detected
 +[    6.352000] IFXUSB: ifxusb_hcd: version 3.2 B110801
 +[    6.860000] IFXUSB: USB core #0 soft-reset
 +[    7.064000] IFXUSB: USB core #0 soft-reset
 +[    7.068000] ifxusb_hcd ifxusb_hcd: IFX USB Controller
 +[    7.072000] ifxusb_hcd ifxusb_hcd: new USB bus registered, assigned bus number 4
 +[    7.080000] ifxusb_hcd ifxusb_hcd: irq 62, io mem 0xbe101000
 +[    7.084000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode
 +[    7.092000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode
 +[    7.096000] IFXUSB: Init: Power Port (0)
 +[    7.104000] hub 4-0:1.0: USB hub found
 +[    7.108000] hub 4-0:1.0: 1 port detected
 +[    7.112000] ifxusb_hcd ifxusb_hcd: requested GPIO 208
 +procd: - preinit -
 +[    7.428000] random: mktemp urandom read with 99 bits of entropy available
 +Press the [f] key and hit [enter] to enter failsafe mode
 +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
 +jffs2 is not ready - marker found
 +procd: - early -
 +procd: - watchdog -
 +procd: - ubus -
 +procd: - init -
 +Please press Enter to activate this console.
 +[  12.904000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH
 +
 +[  12.936000] NET: Registered protocol family 10
 +[  12.956000] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH
 +[  12.968000] NET: Registered protocol family 8
 +[  12.972000] NET: Registered protocol family 20
 +[  12.988000] PPP generic driver version 2.4.2
 +[  13.000000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[  13.020000] IFX MEI Version 5.00.00
 +[  13.036000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
 +[  13.048000] Loading modules backported from Linux version master-2014-09-26-0-g25e3efa
 +[  13.056000] Backport generated by backports.git backports-20140905-1-gde42785
 +[  13.080000] Lantiq MIPS24KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
 +[  13.088000] request_timer(3, 0x000001AE, 1)...successful!
 +[  13.092000] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH
 +[  13.104000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[  13.128000] ATM1.0.26    ATM (A1) firmware version 0.17
 +[  13.132000] ifxmips_atm: ATM init succeed
 +[  13.156000] nf_conntrack version 0.5.0 (947 buckets, 3788 max)
 +[  13.192000] NET: Registered protocol family 24
 +[  13.236000] xt_time: kernel timezone is -0000
 +[  13.252000] random: nonblocking pool is initialized
 +[  13.304000] cfg80211: Calling CRDA to update world regulatory domain
 +[  13.312000] cfg80211: World regulatory domain updated:
 +[  13.316000] cfg80211:  DFS Master region: unset
 +[  13.320000] cfg80211:  (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
 +[  13.328000] cfg80211:  (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
 +[  13.336000] cfg80211:  (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
 +[  13.344000] cfg80211:  (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
 +[  13.352000] cfg80211:  (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
 +[  13.360000] cfg80211:  (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
 +[  13.368000] cfg80211:  (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
 +[  13.376000] cfg80211:  (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
 +[  13.384000] cfg80211:  (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
 +[  13.536000] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002)
 +[  13.544000] rt2800pci 0000:00:0e.0: failed to load eeprom property
 +[  13.548000] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'RT2860.eeprom'.
 +[  13.556000] rt2800pci 0000:00:0e.0: Direct firmware load failed with error -2
 +[  13.564000] rt2800pci 0000:00:0e.0: Falling back to user helper
 +[  13.728000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3572, rev 0223 detected
 +[  13.736000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0008 detected
 +[  26.976000] device eth0.1 entered promiscuous mode
 +[  26.980000] device eth0 entered promiscuous mode
 +[  26.992000] br-lan: port 1(eth0.1) entered forwarding state
 +[  26.996000] br-lan: port 1(eth0.1) entered forwarding state
 +[  29.000000] br-lan: port 1(eth0.1) entered forwarding state
 +[  31.232000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
 +[  31.248000] jffs2_build_filesystem(): unlocking the mtd device... done.
 +[  31.252000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
 +[  69.076000] jffs2: notice: (1110) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
 +procd: - init complete -
 +
 +
 +
 +BusyBox v1.22.1 (2014-10-05 01:42:11 BST) built-in shell (ash)
 +Enter 'help' for a list of built-in commands.
 +
 +  _______                    ________        __
 + |      |.-----.-----.-----.|  |  |  |.----.|  |_
 + |  -  ||  _  |  -__|    ||  |  |  ||  _||  _|
 + |_______||  __|_____|__|__||________||__|  |____|
 +          |__| W I R E L E S S  F R E E D O M
 + -----------------------------------------------------
 + CHAOS CALMER (Bleeding Edge, r42701)
 + -----------------------------------------------------
 +  * 1 1/2 oz Gin            Shake with a glassful
 +  * 1/4 oz Triple Sec      of broken ice and pour
 +  * 3/4 oz Lime Juice      unstrained into a goblet.
 +  * 1 1/2 oz Orange Juice
 +  * 1 tsp. Grenadine Syrup
 + -----------------------------------------------------
 +root@OpenWrt:/#
 +
 +
 +</code>
 +
 +
 +for problems with wlan eeprom:
 +
 +https://forum.openwrt.org/viewtopic.php?pid=223479#p223479
===== Tags ===== ===== Tags =====
{{tag>FastEthernet 4Port USB 3USB serial InternalAntenna 64RAM 8Flash MIPS MIPS32 24K ADSL2+ lantiq danube 802.11bgn fxo}} {{tag>FastEthernet 4Port USB 3USB serial InternalAntenna 64RAM 8Flash MIPS MIPS32 24K ADSL2+ lantiq danube 802.11bgn fxo}}

Back to top

toh/astoria/arv752dpw22.1392647911.txt.bz2 · Last modified: 2014/02/17 15:38 (external edit)