You are here: OpenWrt Wiki » Table of Hardware » Asus » Asus WL600g

Differences

This shows you the differences between two versions of the page.

--- toh:asus:wl600g [2013/02/02 07:05]
markcoker
+++ toh:asus:wl600g [2013/05/08 16:30] (current)
danitool
@@ Line 1: / Line 1: @@
 ====== Asus WL600g ======
-It works (apart ADSL) using latest releases:
+Supported, but without ADSL.
-http://downloads.openwrt.org/snapshots/trunk/brcm63xx/openwrt-96348GW-generic-squashfs-cfe.bin
+  * Backfire (10.03.1):\\ [[http://downloads.openwrt.org/backfire/10.03.1/brcm63xx/openwrt-96348GW-generic-squashfs-cfe.bin|openwrt-96348GW-generic-squashfs-cfe.bin]]
+  * Attitude Adjustment (12.09):\\ [[http://downloads.openwrt.org/attitude_adjustment/12.09/brcm63xx/generic/openwrt-96348GW-generic-squashfs-cfe.bin|openwrt-96348GW-generic-squashfs-cfe.bin]]
-http://downloads.openwrt.org/backfire/10.03.1-rc4/brcm63xx/openwrt-96348GW-generic-squashfs-cfe.bin
+  * Trunk:\\ [[http://downloads.openwrt.org/snapshots/trunk/brcm63xx/openwrt-96348GW-generic-squashfs-cfe.bin|openwrt-96348GW-generic-squashfs-cfe.bin]]
-FIXME Someone tried with ASUS/BROADCOM ADSL native binaries?
 ===== Hardware =====
@@ Line 14: / Line 12: @@
 | **Vendor:**          | [[wp>Broadcom]] |
 | **[[doc:techref:Bootloader]]:**     | [[doc:techref:bootloader:CFE]] |
-| **[[doc:hardware:soc|System-On-Chip]]:**  | bcm6348 |
+| **Board Id: **    | 96348GW-10 |
+| **[[doc:hardware:soc|System-On-Chip]]:**  | BCM6348 |
 | **[[doc:hardware:cpu|CPU]]/Speed**        | BMIPS3300 V0.7 / 256 MHz |
 | **Flash-Chip:**      | MX29LV320CBTC-90G |
@@ Line 44: / Line 43: @@
 Image of Serial & JTAG
-{{:media:wl600g_serial.and.jtag.png|}}
+{{:media:wl600g_serial.and.jtag.png?400|}}
 ===== Software =====
@@ Line 69: / Line 68: @@
 ===== Serial =====
-J503 (needs to be comfirmed) is a serial port that could be cabled to get access to router console. 115000 8N1\\
+J503 is a serial port that could be cabled to get access to router console. 115000 8N1\\
 Signals are 3.3V like many other boards. \\
 Pinout:\\
@@ Line 75: / Line 74: @@
 N/A | TX\\
 N/A | RX\\
 ===== JTAG Port =====
@@ Line 86: / Line 84: @@
 ===== Custom firmwares =====
-TODO
+Dumb wifi radio, see thread [[https://forum.openwrt.org/viewtopic.php?pid=180020#p180020|Router for mpd like Asus WL 500g]]:
+[[http://files.myopera.com/danitool/linux/WL600g_Backfire_10.03.2_wifiradio3.zip|WL600g_Backfire_10.03.2_wifiradio3.zip]]
 ===== Interesting threads =====
@@ Line 97: / Line 98: @@
 ===== Connect stuff to the USB port =====
 To connect stuff to the USB port, please see [[doc:howto:usb.overview|Connect stuff to the USB port]].
+===== Bootlogs =====
+This is the serial output on start.
+==== OEM bootlog ====
+<HTML>
+<p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF">
+<code>
+CFE version 1.0.37-0.8 for BCM96348 (32bit,SP,BE)
+Build Date: ¤@  2¤ë 20 18:37:34 CST 2006 (root@localhost.localdomain)
+Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
+Initializing Arena.
+Initializing Devices.
+CPU type 0x29107: 256MHz, Bus: 128MHz, Ref: 32MHz
+Total memory used by CFE:  0x80401000 - 0x805246F0 (1193712)
+Initialized Data:          0x8041C680 - 0x8041E080 (6656)
+BSS Area:                  0x8041E080 - 0x804226F0 (18032)
+Local Heap:                0x804226F0 - 0x805226F0 (1048576)
+Stack Area:                0x805226F0 - 0x805246F0 (8192)
+Text (code) segment:       0x80401000 - 0x8041C67C (112252)
+Boot area (physical):      0x00525000 - 0x00565000
+Relocation Factor:         I:00000000 - D:00000000
+Board IP address                : 192.168.1.1:ffffff00
+Host IP address                 : 192.168.1.100
+Gateway IP address              :
+Run from flash/host (f/h)       : f
+Default host run file name      : vmlinux
+Default host flash file name    : bcm963xx_fs_kernel
+Boot delay (0-9 seconds)        : 1
+Board Id Name                   : 96348GW-10
+Psi size in KB                  : 24
+Number of MAC Addresses (1-32)  : 11
+Base MAC Address                : 00:1b:fc:c1:38:21
+Ethernet PHY Type               : Internal
+Memory size in MB               : 16
+*** Press any key to stop auto run (1 seconds) ***
+Auto run second count down: 110
+GPIOio_PIN_HIGH is Off
+Code Address: 0x80010000, Entry Address: 0x8024a018
+Decompression OK!
+Entry at 0x8024a018
+Closing network.
+Starting program at 0x8024a018
+Linux version 2.6.8.1 (root@localhost.localdomain) (gcc version 3.4.2) #1 Tue Feb 9 17:43:54 CST 2010
+Total Flash size: 4096K with 71 sectors
+GW-10 prom init
+CPU revision is: 00029107
+mpi: No Card is in the PCMCIA slot
+Determined physical RAM map:
+ memory: 00fa0000 @ 00000000 (usable)
+On node 0 totalpages: 4000
+  DMA zone: 4000 pages, LIFO batch:1
+  Normal zone: 0 pages, LIFO batch:1
+  HighMem zone: 0 pages, LIFO batch:1
+Built 1 zonelists
+Kernel command line: root=31:0 ro noinitrd
+brcm mips: enabling icache and dcache...
+Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
+Primary data cache 8kB 2-way, linesize 16 bytes.
+PID hash table entries: 64 (order 6: 512 bytes)
+Using 128.000 MHz high precision timer.
+Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
+Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
+Memory: 13324k/16000k available (1590k kernel code, 2656k reserved, 686k data, 76k init, 0k highmem)
+Calibrating delay loop... 255.59 BogoMIPS
+Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
+Checking for 'wait' instruction...  unavailable.
+NET: Registered protocol family 16
+Can't analyze prologue code at 8019bf84
+usbcore: registered new driver usbfs
+usbcore: registered new driver hub
+devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
+devfs: boot_options: 0x1
+NTFS driver 2.1.15 [Flags: R/O DEBUG].
+PPP generic driver version 2.4.2
+NET: Registered protocol family 24
+Linux video capture interface: v1.00
+Using noop io scheduler
+bcm963xx_mtd driver v1.0
+brcmboard: brcm_board_init entry
+bcm963xx_serial driver v2.0
+u32 classifier
+    OLD policer on
+NET: Registered protocol family 2
+IP: routing cache hash table of 512 buckets, 4Kbytes
+TCP: Hash tables configured (established 512 bind 1024)
+NET: Registered protocol family 1
+NET: Registered protocol family 17
+Ebtables v2.0 registered
+NET: Registered protocol family 8
+NET: Registered protocol family 20
+.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
+All bugs added by David S. Miller <davem@redhat.com>
+VFS: Mounted root (squashfs filesystem) readonly.
+Mounted devfs on /dev
+Freeing unused kernel memory: 76k freed
+init started:  BusyBox v1.00 (2010.02.09-09:52+0000) multi-call binary
+Algorithmics/MIPS FPU Emulator v1.5
+BusyBox v1.00 (2010.02.09-09:52+0000) Built-in shell (msh)
+Enter 'help' for a list of built-in commands.
+Loading drivers and kernel modules...
+Asus mknod Init
+Asus mknod finish (Roly)
+Using /lib/modules/2.6.8.1/extra/atmapi.ko
+atmapi: module license 'Proprietary' taints kernel.
+Using /lib/modules/2.6.8.1/extra/blaadd.ko
+blaadd: blaa_detect entry
+Using /lib/modules/2.6.8.1/extra/adsldd.ko
+adsl: adsl_init entry
+Using /lib/modules/2.6.8.1/extra/bcmprocfs.ko
+Broadcom BCMPROCFS v1.0 initialized
+Using /lib/modules/2.6.8.1/extra/bcm_enet.ko
+Broadcom BCM6348B0 Ethernet Network Device v0.3 Feb  9 2010 17:42:35
+Config Ethernet Switch Through MDIO Sseudo PHY Interface
+eth0: MAC Address: 00:1B:FC:C1:38:21
+Using /lib/modules/2.6.8.1/extra/bcm_usb.ko
+Broadcom BCM6348B0 USB Network Device v0.4 Feb  9 2010 20:14:40
+usb0: MAC Address: 00 1B FC C1 38 21
+usb0: Host MAC Address: 00 1B FC C1 38 21
+Using /lib/modules/2.6.8.1/extra/wl.ko
+PCI: Setting latency timer of device 0000:00:01.0 to 64
+PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
+wl: srom not detected, using main memory mapped srom info (wombo board)
+wl0: wlc_attach: using main board MAC address base in NVRAM (wombo board)
+wl0 MAC Address: 00:1B:FC:C1:38:21
+dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
+wl0: Broadcom BCM4318 802.11 Wireless Controller 3.91.41.0
+cfm init()
+xmlEndWebCamobj is not xmlstate.verify!!!
+xmlEndFTPobj is not xmlstate.verify
+xmlEndQoSobj is not xmlstate.verify
+eth0 Link UP.
+BcmAdsl_Initialize=0xC0054208, g_pFnNotifyCallback=0xC00673A4
+AdslCoreHwReset: AdslOemDataAddr = 0xA0FF8054
+dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_tables.ko
+ip_tables: (C) 2000-2002 Netfilter core team
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/iptable_filter.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack.ko
+ip_conntrack version 2.1 (125 buckets, 0 max) - 384 bytes per conntrack
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/iptable_nat.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/iptable_mangle.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_conntrack_ipsec.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_nat_ipsec.ko
+insmod ip_conntrack_ftp port:1111
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_ftp.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_gre.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_h323.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_irc.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_pptp.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_rtsp.ko
+ip_conntrack_rtsp: falsely claims to have parameter setup_timeout
+ip_conntrack_rtsp v0.01 loading
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_tftp.ko
+insmod ip_nat_ftp port:1111
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_ftp.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_gre.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_h323.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_irc.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_pptp.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_rtsp.ko
+ip_nat_rtsp v0.01 loading
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_tftp.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_FTOS.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_LOG.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_MARK.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_MASQUERADE.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_REDIRECT.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_TCPMSS.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_layer7.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_length.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_limit.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_mark.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_state.ko
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ipt_tcpmss.ko
+ADSL G.994 training
+==>   Bcm963xx Software Version: 3.02L.01.A2pB018e.d16f   <==
+device usb0 entered promiscuous mode
+br0: port 1(usb0) entering learning state
+br0: topology change detected, propagating
+br0: port 1(usb0) entering forwarding state
+device eth0 entered promiscuous mode
+br0: port 2(eth0) entering learning state
+br0: topology change detected, propagating
+br0: port 2(eth0) entering forwarding state
+pvc2684d: Interface "nas_8_35" created sucessfully
+pvc2684d: Communicating over ATM 0.8.35, encapsulation: LLC
+device nas_8_35 entered promiscuous mode
+br0: port 3(nas_8_35) entering learning state
+br0: topology change detected, propagating
+br0: port 3(nas_8_35) entering forwarding state
+device usb0 left promiscuous mode
+br0: port 1(usb0) entering disabled state
+device usb0 entered promiscuous mode
+br0: port 1(usb0) entering learning state
+br0: topology change detected, propagating
+br0: port 1(usb0) entering forwarding state
+ADSL G.992 started
+device eth0 left promiscuous mode
+br0: port 2(eth0) entering disabled state
+device eth0 entered promiscuous mode
+br0: port 2(eth0) entering learning state
+br0: topology change detected, propagating
+br0: port 2(eth0) entering forwarding state
+device wl0 entered promiscuous mode
+infosvr start!!!
+xmlEndWebCamobj is not xmlstate.verify!!!
+xmlEndFTPobj is not xmlstate.verify
+xmlEndQoSobj is not xmlstate.verify
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_conntrack_ipsec.ko
+insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_conntrack_ipsec.ko': Success (17): Success
+Using /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_nat_ipsec.ko
+insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/broadcom/ip_nat_ipsec.ko': Success (17)sntp: host not found
+xmlEndWebCamobj is not xmlstate.verify!!!
+xmlEndFTPobj is not xmlstate.verify
+xmlEndQoSobj is not xmlstate.verify
+watchdog init testing!!!!!!!!!
+: Success
+uhci_hcd: falsely claims to have parameter debug
+USB Universal Host Controller Interface driver v2.2
+PCI: Enabling device 0000:00:07.0 (0000 -> 0001)
+uhci_hcd 0000:00:07.0: UHCI Host Controller
+uhci_hcd 0000:00:07.0: irq 32, io base 0c000000
+uhci_hcd 0000:00:07.0: new USB bus registered, assigned bus number 1
+ADSL G.992 channel analysis
+hub 1-0:1.0: USB hub found
+hub 1-0:1.0: 2 ports detected
+PCI: Enabling device 0000:00:07.1 (0000 -> 0001)
+uhci_hcd 0000:00:07.1: UHCI Host Controller
+uhci_hcd 0000:00:07.1: irq 32, io base 0c000020
+uhci_hcd 0000:00:07.1: new USB bus registered, assigned bus number 2
+hub 2-0:1.0: USB hub found
+hub 2-0:1.0: 2 ports detected
+PCI: Enabling device 0000:00:07.2 (0000 -> 0002)
+ehci_hcd 0000:00:07.2: EHCI Host Controller
+capbase:::1000010
+capbase:::1000010
+ehci_hcd 0000:00:07.2: irq 32, pci mem a8010800
+ehci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 3
+ehci_hcd 0000:00:07.2: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
+hub 3-0:1.0: USB hub found
+hub 3-0:1.0: 4 ports detected
+usblp: falsely claims to have parameter proto_bias
+usbcore: registered new driver usblp
+drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
+ov511: falsely claims to have parameter ov518_color
+usbcore: registered new driver ov511
+drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
+pwc: falsely claims to have parameter dev_hint
+pwc Philips webcam module version 9.0.1 loaded.
+pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
+pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
+pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
+usbcore: registered new driver Philips webcam
+SCSI subsystem initialized
+ADSL link up, fast, us=1148, ds=0
+Initializing USB Mass Storage driver...
+usbcore: registered new driver usb-storage
+USB Mass Storage support registered.
+br0: port 1(usb0) entering disabled state
+PPP: PPP8_35_1 Start to connect ...
+ADSL link down
+ADSL G.994 training
+ADSL G.992 channel analysis
+ADSL link up, fast, us=1020, ds=0
+PPP: PPP8_35_1 Start to connect ...
+std_rcv_pado: ses->state= 07, p_in->code=07, PADO_CODE=07
+std_rcv_pado: ses->state= 65, p_in->code=07, PADO_CODE=07
+std_rcv_pado: ses->state= 65, p_in->code=07, PADO_CODE=07
+std_rcv_pado: ses->state= 65, p_in->code=07, PADO_CODE=07
+std_rcv_pado: ses->state= 65, p_in->code=07, PADO_CODE=07
+std_rcv_pado: ses->state= 65, p_in->code=07, PADO_CODE=07
+PPP: PPP8_35_1 Connection Up.
+Primary DNS server = 8.8.8.8
+Secondary DNS server = 8.8.4.4
+ftp: 0 0,http: 2 2,telnet: 0 0, tftpd: 2 2
+usb_ftpport is 1111
+:49:36 INFO:siproxd.c:192 siproxd-0.5.10-3874 i686-redhat-linux-gnu starting up
+</code>
+</p>
+</HTML>
 ===== Tags =====
 {{tag>bcm63xx bcm6348}}

toh/asus/wl600g.1359785130.txt.bz2 · Last modified: 2013/02/02 07:05 by markcoker

OpenWrt

Wiki Search

Actions

Donate

Translations

Differences