User Tools

Site Tools


toh:asus:wlhdd2.5

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

toh:asus:wlhdd2.5 [2012/11/08 16:51]
toh:asus:wlhdd2.5 [2015/04/19 16:47] (current)
zo0ok [ASUS WL-HDD] Adding note about CPU
Line 1: Line 1:
 ====== ASUS WL-HDD ====== ====== ASUS WL-HDD ======
 +// 20150419 zo0ok: Unclear if there are two versions with 125MHz/​200MHz cpu or if it is not know. Also unclear about platform/​chipset. Please clearify here and in ToH. (and remove this note) //
 ====== Yakumo Wireless Storage 60 ====== ====== Yakumo Wireless Storage 60 ======
 The device is supported in OpenWrt (White Russian and later). Confirmed running Version are WhiteRussian,​ Kamikaze and BackFire. You need to install the openwrt-brcm47xx-squashfs.trx (BackFire) or openwrt-brcm-2.4-squashfs.trx firmware images. The device is supported in OpenWrt (White Russian and later). Confirmed running Version are WhiteRussian,​ Kamikaze and BackFire. You need to install the openwrt-brcm47xx-squashfs.trx (BackFire) or openwrt-brcm-2.4-squashfs.trx firmware images.
Line 9: Line 10:
  
 ===== Installation ===== ===== Installation =====
-See  [[doc:howto:installing|Installing OpenWrt]]. Using the tftp-method is described there: [[oldwiki:​OpenWrtDocs:​Hardware:​Asus:​Flashing|Asus Flashing]].+See  [[doc/howto/​generic.flashing|Installing OpenWrt ​(generic)]]. Using the tftp-method is described there: [[oldwiki:​OpenWrtDocs:​Hardware:​Asus:​Flashing|Asus Flashing]].
  
-=== BackFire === +==== BackFire ​==== 
-You need to change /​etc/​hotplug.d/​net/​10-net (see [[https://​dev.openwrt.org/​ticket/​5312]]) to get the wireless interface running. ​+You may need to change /​etc/​hotplug.d/​net/​10-net (see [[https://​dev.openwrt.org/​ticket/​5312]]) to get the wireless interface running. ​
  
-The device produces a lot of '​process '/​bin/​ash --login'​ (pid 1212) exited. Scheduling for restart.'​ messages in the syslog. Removing '​ttyS0::​askfirst:/​bin/​ash --login'​ in /​etc/​inittab solves this problem. ​+If the device produces a lot of '​process '/​bin/​ash --login'​ (pid 1212) exited. Scheduling for restart.'​ messages in the syslog. Removing '​ttyS0::​askfirst:/​bin/​ash --login'​ in /​etc/​inittab solves this problem. ​
  
-In the installation by default, the two module b43 and b43legacy are loaded but b43 is the only needed. So you can remove the loading of b43legacy at the beginning by removing 30-b43-legacy from the directory /​etc/​config/​modules.d+In the installation by default, the two module ​[[http://​linuxwireless.org/​en/​users/​Drivers/​b43#​Supported_devices|b43 and b43legacy]] are loaded but b43 is the only needed. So you can remove the loading of b43legacy at the beginning by removing 30-b43-legacy from the directory /​etc/​config/​modules.d
  
-=== Kamikaze ===+==== Kamikaze ​====
  
 The boot_wait NVRAM variable is **on** by default. Resetting to factory defaults via reset button or mtd erase nvram is **not safe** on this unit. The boot_wait NVRAM variable is **on** by default. Resetting to factory defaults via reset button or mtd erase nvram is **not safe** on this unit.
Line 176: Line 177:
 | **Flash-Chip:​** ​     | MX 29LV320ATTC-90 | | **Flash-Chip:​** ​     | MX 29LV320ATTC-90 |
 | **Flash size:​** ​     | 4 MiB | | **Flash size:​** ​     | 4 MiB |
-| **RAM:​** ​            | Hynix HY57V283220T-7 |+| **RAM:​** ​            | Hynix HY57V283220T-7 ​/ SDR-143 ​|
 | **RAM size:​** ​       | 16 MiB | | **RAM size:​** ​       | 16 MiB |
-| **Wireless:​** ​       | Broadcom BCM4306 802.11b/g (mini-pci)\\ PCI-ID 14e4:4320 (rev 03) |+| **Wireless:​** ​       | Broadcom BCM4306 802.11b/g (onboard)\\ PCI-ID 14e4:4320 (rev 03) |
 | **Ethernet:​** ​       | 1x network controller, no switch | | **Ethernet:​** ​       | 1x network controller, no switch |
 | **USB:​** ​            | Yes 1x1.1, second port possible | | **USB:​** ​            | Yes 1x1.1, second port possible |
Line 193: Line 194:
 If you want to open the device (maybe for exchanging the disk) remove the screws below the two little rubber-pads (could be that there are no screws, as on my yakumo. just pull on). Then slide the mainboard with the HD on it out of the case by carefully pulling the front plate. If you want to open the device (maybe for exchanging the disk) remove the screws below the two little rubber-pads (could be that there are no screws, as on my yakumo. just pull on). Then slide the mainboard with the HD on it out of the case by carefully pulling the front plate.
  
 +{{:​toh:​asus:​asus:​wlhdd2.5:​wl_hdd_usb_all1.jpg?​400|}}\\
 //Main PCB// //Main PCB//
  
-FIXME 
- 
-**Photo of PCB** 
  
 ==== Nvram Reset ==== ==== Nvram Reset ====
Line 309: Line 308:
 This device has some solder pads for a external interface like the WL-500G. For using it please read [[http://​forum.openwrt.org/​viewtopic.php?​id=7083|this forum postings]]. This device has some solder pads for a external interface like the WL-500G. For using it please read [[http://​forum.openwrt.org/​viewtopic.php?​id=7083|this forum postings]].
  
 +===== Tags =====
 +For some Help with the Tags, please have a look here: [[meta/​tags]]
  
 +{{tag>​bcm47xx bcm4702 FastEthernet 1Port 1USB 802.11bg 1Ant 16RAM 4Flash MIPS MIPS32}}
toh/asus/wlhdd2.5.1352389919.txt.bz2 · Last modified: 2012/11/08 16:51 (external edit)