User Tools

Site Tools


toh:audiocodes:mp252

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

toh:audiocodes:mp252 [2013/03/11 16:33]
toh:audiocodes:mp252 [2013/07/27 11:22] (current)
Line 1: Line 1:
-====== ​AudioCodes ​MP-252 ======+====== ​MediaPack ​MP-252 ======
 This Lantiq-based CPE board is labled >​EP-GW<​ TW_UP_UP-MVO-1 This Lantiq-based CPE board is labled >​EP-GW<​ TW_UP_UP-MVO-1
  
Line 6: Line 6:
 Besides the features one would expect from a Lantiq Danube XWAY board, this one also offers a 4P4C socket for a backup battery. Besides the features one would expect from a Lantiq Danube XWAY board, this one also offers a 4P4C socket for a backup battery.
  
-It comes with Jungo'​s OpenRG ​firmare.+It comes with Jungo'​s OpenRG ​firmware.
  
 **<color yellow>​The device is not fully supported yet (but about to be)</​color>​** **<color yellow>​The device is not fully supported yet (but about to be)</​color>​**
  
 ===== Notes ===== ===== Notes =====
-=== Working===+=== Working ===
   * serial :)   * serial :)
  
   * Ethernet   * Ethernet
-still required ​either booting from self-made U-Boot or forcing the vendor U-Boot to initialize the switch (e.g. tftp ...)+still requires ​either booting from self-made U-Boot or forcing the vendor U-Boot to initialize the switch (e.g. tftp ...)
  
   * USB (tested)   * USB (tested)
Line 24: Line 24:
 eth0: tx ring full eth0: tx ring full
  
-=== Not working yet===+=== Not working yet ===
   * ADSL   * ADSL
 driver loads, never gets past 0x300 handshake driver loads, never gets past 0x300 handshake
  
   * TAPI/VoIP   * TAPI/VoIP
-reference drivers probed ok, however, since Si SLICs are used, we'll need a driver for those and working SPI support...+reference drivers probed ok, however, since a Si3220 dual-SLIC is used, we'll need a driver for that and working SPI support...
  
 ===== Hardware Highlights ===== ===== Hardware Highlights =====
Line 46: Line 46:
 | **Flash size:​** ​     | 32 MiB | | **Flash size:​** ​     | 32 MiB |
 | **RAM:​** ​            | 64 MiB | | **RAM:​** ​            | 64 MiB |
-| **Wireless:​** ​       | Ralink Rt3062F 2.4ghz 802.11bgn 2T2R PCI | +| **Wireless:​** ​       ​| [[http://​www.mediatek.com/​_en/​01_products/​04_pro.php?​sn=1011|Ralink Rt3062F]] 2.4ghz 802.11bgn 2T2R PCI | 
-| **POTS:​** ​           | 2x FXS |+| **POTS:​** ​           | [[http://​www.silabs.com/​products/​voice/​slic/​Pages/​Si32xxDualProSLIC.aspx|Silicon Laboratories Si3220 + Si3208]] ​2x FXS |
 | **Ethernet:​** ​       | [[http://​web.archive.org/​web/​20050420132752/​http://​www.infineon.com/​cgi/​ecrm.dll/​ecrm/​scripts/​prod_ov.jsp?​oid=58991&​cat_oid=-12486|Infenion ADM6996I]] | | **Ethernet:​** ​       | [[http://​web.archive.org/​web/​20050420132752/​http://​www.infineon.com/​cgi/​ecrm.dll/​ecrm/​scripts/​prod_ov.jsp?​oid=58991&​cat_oid=-12486|Infenion ADM6996I]] |
 | **Internet:​** ​       | ADSL2+ | | **Internet:​** ​       | ADSL2+ |
Line 59: Line 59:
 ==== Serial ==== ==== Serial ====
 There is a serial port on the marked pinheaders (3.3V TTL level!) There is a serial port on the marked pinheaders (3.3V TTL level!)
 +
 +The unpopulated header just above is EJTAG (tested, works)
  
 {{:​media:​ac252-serial.jpg|}} {{:​media:​ac252-serial.jpg|}}
Line 87: Line 89:
 ==== U-Boot ==== ==== U-Boot ====
 Patch was sent Patch was sent
-[[http://​dev.phrozen.org/​gitweb/?​p=uboot-upstream.git;​a=commit;​h=151a4a3b676947bd55d8af1838ccd2f82b3e911f|upstream]].+[[http://​dev.phrozen.org/​gitweb/?​p=uboot-upstream.git;​a=commit;​h=f09e4ffeb5f4278cc218aba1e87aa704fc082e6e|upstream]].
  
 ==== Flash Layout ==== ==== Flash Layout ====
Line 132: Line 134:
 ^ name ^ start ^ end ^ size ^ ^ name ^ start ^ end ^ size ^
 | uboot | 0x00000000 | 0x0001FFFF | 0x00020000 | | uboot | 0x00000000 | 0x0001FFFF | 0x00020000 |
-| ubootconfig | 0x00020000 | 0x0003FFFF | 0x00010000 ​|+| ubootconfig | 0x00020000 | 0x0003FFFF | 0x00020000 ​|
 | settings | 0x00040000 | 0x0009FFFF | 0x00060000 | | settings | 0x00040000 | 0x0009FFFF | 0x00060000 |
 | linux (kernel+rootfs) | 0x000A0000 | 0x00FBFFFF | 0x00F20000 | | linux (kernel+rootfs) | 0x000A0000 | 0x00FBFFFF | 0x00F20000 |
Line 558: Line 560:
 <p style="​padding:​ 10px;​border:​1px solid grey;​height:​600px;​font:​10px/​14px Georgia, Garamond, Serif;​overflow:​Auto;​background-color:#​FFFFFF">​ <p style="​padding:​ 10px;​border:​1px solid grey;​height:​600px;​font:​10px/​14px Georgia, Garamond, Serif;​overflow:​Auto;​background-color:#​FFFFFF">​
 <​code>​ <​code>​
-ÿ+ROM VER: 1.0.3 
 +CFG 01 
 +Read
 ROM VER: 1.0.3 ROM VER: 1.0.3
 CFG 01 CFG 01
Line 565: Line 569:
  
  
-U-Boot 1.1.5.8-IAD-1664 (Mar 16 2010 - 13:47:19)+U-Boot 1.1.5.4-IAD-3264 (Jan 17 2010 - 10:42:44)
  
 DRAM:  64 MB DRAM:  64 MB
Line 571: Line 575:
  ​relocate_code start  ​relocate_code start
  ​relocate code finish.  ​relocate code finish.
-Flash: ​16 MB+Flash: ​32 MB
 In:    serial In:    serial
 Out:   ​serial Out:   ​serial
Line 580: Line 584:
 Type "run flash_nfs"​ to mount root filesystem over NFS Type "run flash_nfs"​ to mount root filesystem over NFS
  
-Hit any key to stop autoboot: ​ 3  2  1  0  +Hit any key to stop autoboot: ​ 3  2  0  
-## Booting image at b00a0000 ​... +DANUBE # tftp 0x81000000 openwrt-lantiq-xway-ACMP252-uImage 
-   Image Name:   MIPS OpenWrt Linux-3.7.10 +Using danube Switch device 
-   ​Created: ​     2013-03-06   6:29:26 UTC+TFTP from server 192.168.1.20;​ our IP address is 192.168.1.1 
 +Filename '​openwrt-lantiq-xway-ACMP252-uImage'​. 
 +Load address: 0x81000000 
 +Loading: #################################################################​ 
 + #################################################################​ 
 + #################################################################​ 
 + #################################################################​ 
 + #################################################################​ 
 + #################################################################​ 
 + #################################################################​ 
 + #################################################################​ 
 + #################################################################​ 
 + #################################################################​ 
 + #################################################################​ 
 + ###################################################​ 
 +done 
 +Bytes transferred = 3918797 (3bcbcd hex) 
 +DANUBE # bootm 
 +## Booting image at 81000000 ​... 
 +   Image Name:   MIPS OpenWrt Linux-3.8.3 
 +   ​Created: ​     2013-03-17  18:25:45 UTC
    Image Type:   MIPS Linux Kernel Image (lzma compressed)    Image Type:   MIPS Linux Kernel Image (lzma compressed)
-   Data Size:    ​1183502 ​Bytes =  ​1.MB+   Data Size:    ​3918733 ​Bytes =  ​3.MB
    Load Address: 80002000    Load Address: 80002000
    Entry Point: ​ 80002000    Entry Point: ​ 80002000
Line 593: Line 617:
 Starting kernel ... Starting kernel ...
  
-[    0.000000] Linux version 3.7.10 (daniel@earthship) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #12 Wed Mar 6 08:29:19 IST 2013+[    0.000000] Linux version 3.8.(daniel@earthship) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #1 Sun Mar 17 20:25:31 IST 2013
 [    0.000000] SoC: Danube rev 1.3 [    0.000000] SoC: Danube rev 1.3
 [    0.000000] bootconsole [early0] enabled [    0.000000] bootconsole [early0] enabled
 [    0.000000] CPU revision is: 00019641 (MIPS 24KEc) [    0.000000] CPU revision is: 00019641 (MIPS 24KEc)
-[    0.000000] Board: MP-252 - AudioCodes MediaPack MP-252 
 [    0.000000] Determined physical RAM map: [    0.000000] Determined physical RAM map:
 [    0.000000] ​ memory: 04000000 @ 00000000 (usable) [    0.000000] ​ memory: 04000000 @ 00000000 (usable)
Line 614: Line 637:
 [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 [    0.000000] __ex_table already sorted, skipping sort [    0.000000] __ex_table already sorted, skipping sort
-[    0.000000] Writing ErrCtl register=0007ff6c +[    0.000000] Writing ErrCtl register=0007ff68 
-[    0.000000] Readback ErrCtl register=0007ff6c +[    0.000000] Readback ErrCtl register=0007ff68 
-[    0.000000] Memory: ​61196k/65536k available (2516k kernel code, 4340k reserved, ​766k data, 228k init, 0k highmem)+[    0.000000] Memory: ​52680k/65536k available (2570k kernel code, 12856k ​reserved, ​784k data, 8668k init, 0k highmem)
 [    0.000000] NR_IRQS:256 [    0.000000] NR_IRQS:256
 [    0.000000] CPU Clock: 333MHz [    0.000000] CPU Clock: 333MHz
Line 638: Line 661:
 [    0.144000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [    0.144000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
 [    0.148000] pci 0000:​00:​0e.0:​ BAR 0: assigned [mem 0x18000000-0x1800ffff] [    0.148000] pci 0000:​00:​0e.0:​ BAR 0: assigned [mem 0x18000000-0x1800ffff]
-[    0.152000] pci 0000:​00:​0e.0:​ SLOT:14 PIN:1 IRQ:135+[    0.152000] pci 0000:​00:​0e.0:​ SLOT:14 PIN:1 IRQ:30
 [    0.156000] Switching to clocksource MIPS [    0.156000] Switching to clocksource MIPS
 [    0.164000] NET: Registered protocol family 2 [    0.164000] NET: Registered protocol family 2
-[    0.172000] TCP established hash table entries: ​2048 (order: ​216384 bytes) +[    0.172000] TCP established hash table entries: ​512 (order: ​04096 bytes) 
-[    0.180000] TCP bind hash table entries: ​2048 (order: 1, 8192 bytes) +[    0.180000] TCP bind hash table entries: ​512 (order: ​-1, 2048 bytes) 
-[    0.184000] TCP: Hash tables configured (established ​2048 bind 2048)+[    0.184000] TCP: Hash tables configured (established ​512 bind 512)
 [    0.192000] TCP: reno registered [    0.192000] TCP: reno registered
-[    0.196000] UDP hash table entries: 256 (order: 0, 4096 bytes)+[    0.192000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 [    0.200000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [    0.200000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 [    0.208000] NET: Registered protocol family 1 [    0.208000] NET: Registered protocol family 1
-[    0.212000] gptu: totally 6 16-bit timers/​counters +[    0.736000] gptu: totally 6 16-bit timers/​counters 
-[    0.216000] gptu: misc_register on minor 63 +[    0.740000] gptu: misc_register on minor 63 
-[    0.220000] gptu: succeeded to request irq 126 +[    0.744000] gptu: succeeded to request irq 126 
-[    0.228000] gptu: succeeded to request irq 127 +[    0.748000] gptu: succeeded to request irq 127 
-[    0.232000] gptu: succeeded to request irq 128 +[    0.752000] gptu: succeeded to request irq 128 
-[    0.236000] gptu: succeeded to request irq 129 +[    0.756000] gptu: succeeded to request irq 129 
-[    0.240000] gptu: succeeded to request irq 130 +[    0.760000] gptu: succeeded to request irq 130 
-[    0.244000] gptu: succeeded to request irq 131 +[    0.768000] gptu: succeeded to request irq 131 
-[    0.252000] lantiq,vmmc 1f103000.vmmc:​ requested GPIO 255 +[    0.772000] lantiq,vmmc 1f103000.vmmc:​ requested GPIO 255 
-[    0.256000] lantiq,vmmc 1f103000.vmmc:​ reserved 1MB at 0x03900000 +[    0.780000] lantiq,vmmc 1f103000.vmmc:​ reserved 1MB at 0x02900000 
-[    0.264000] ralink,​eeprom ralink_eep.4:​ using RT2860.eeprom as eeprom +[    0.792000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher 
-[    0.276000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher +[    0.800000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 
-[    0.284000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. +[    0.808000] msgmni has been set to 102 
-[    0.292000] msgmni has been set to 119 +[    0.812000] io scheduler noop registered 
-[    0.296000] io scheduler noop registered +[    0.816000] io scheduler deadline registered (default) 
-[    0.300000] io scheduler deadline registered (default) +[    0.824000] 1e100c00.serial:​ ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,​asc 
-[    0.308000] 1e100c00.serial:​ ttyLTQ0 at MMIO 0x1e100c00 (irq = 112) is a lantiq,​asc +[    0.832000] console [ttyLTQ0] enabled, bootconsole disabled 
-[    0.316000] console [ttyLTQ0] enabled, bootconsole disabled +[    0.832000] console [ttyLTQ0] enabled, bootconsole disabled 
-[    0.316000] console [ttyLTQ0] enabled, bootconsole disabled +[    0.848000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e 
-[    0.332000] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e +[    0.856000] Amd/Fujitsu Extended Query Table at 0x0040 
-[    0.340000] Amd/Fujitsu Extended Query Table at 0x0040 +[    0.860000]   ​Amd/​Fujitsu Extended Query version 1.3. 
-[    0.344000]   ​Amd/​Fujitsu Extended Query version 1.3. +[    0.864000] number of CFI chips: 1 
-[    0.348000] number of CFI chips: 1 +[    0.868000ofpart partitions found on MTD device ltq_nor 
-[    0.352000ofpart partitions found on MTD device ltq_nor +[    0.872000] Creating ​MTD partitions on "​ltq_nor":​ 
-[    0.356000] Creating ​MTD partitions on "​ltq_nor":​ +[    0.880000] 0x000000000000-0x000000020000 : "​uboot"​ 
-[    0.360000] 0x000000000000-0x000000020000 : "​uboot"​ +[    0.888000] 0x000000020000-0x000000040000 : "​uboot_env"​ 
-[    0.368000] 0x000000020000-0x000000040000 : "​uboot_env"​ +[    0.892000] 0x000000040000-0x0000000a0000 : "​boardconfig"​ 
-[    0.376000] 0x000000040000-0x0000000a0000 : "​boardconfig"​ +[    0.900000] 0x0000000a0000-0x000000fc0000 ​: "​linux"​ 
-[    0.384000] 0x0000000a0000-0x000002000000 ​: "​linux"​ +[    0.908000] Creating 2 MTD partitions on "​ltq_nor":​ 
-[    0.392000] found squashfs behind kernel +[    0.912000] 0x0000000a0000-0x0000003e0000 ​: "​kernel"​ 
-[    0.392000] Creating 2 MTD partitions on "​ltq_nor":​ +[    0.9200000x0000003e0000-0x000000fc0000 ​: "​rootfs"​ 
-[    0.396000] 0x0000000a0000-0x0000001c0f4e ​: "​kernel"​ +[    0.924000] mtd: partition "​rootfs" ​set to be root filesystem 
-[    0.404000mtd: partition "​kernel"​ must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only +[    0.928000split_squashfsno squashfs found in "ltq_nor
-[    0.420000] 0x0000001c0f4e-0x000002000000 ​: "​rootfs"​ +[    0.9360000x000000fc0000-0x000001000000 ​: "sysconfig
-[    0.420000] mtd: partition "​rootfs" ​must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only +[    0.9440000x000001000000-0x000002000000 : "​rootfs_data"​ 
-[    0.436000mtdpartition ​"rootfs" ​set to be root filesystem +[    0.964000] etop: invalid MAC, using random 
-[    0.440000mtdpartition ​"rootfs_data" ​created automatically,​ ofs=400000, len=1C00000 ​ +[    ​1.020000] libphy: ltq_mii: probed 
-[    0.4480000x000000400000-0x000002000000 : "​rootfs_data"​ +[    ​1.020000] eth0: ADM6996M model PHY found. 
-[    0.468000] etop: invalid MAC, using random +[    ​1.028000] eth0: attached PHY [Infineon ADM6996] (phy_addr=1e180000.etop-ff:​00,​ irq=-1) 
-[    ​0.524000] libphy: ltq_mii: probed +[    ​1.040000] wdt 1f8803f0.watchdog:​ Init done 
-[    ​0.528000] eth0: ADM6996M model PHY found. +[    ​1.044000] TCP: cubic registered 
-[    ​0.532000] eth0: attached PHY [Infineon ADM6996] (phy_addr=1e180000.etop-ff:​00,​ irq=-1) +[    ​1.048000] NET: Registered protocol family 17 
-[    ​0.544000] wdt 1f8803f0.watchdog:​ Init done +[    ​1.052000] 8021q: 802.1Q VLAN Support v1.8 
-[    ​0.552000] TCP: cubic registered +[    ​1.076000] Freeing unused kernel memory: ​8668k freed
-[    ​0.552000] NET: Registered protocol family 17 +
-[    ​0.556000] 8021q: 802.1Q VLAN Support v1.8 +
-[    ​0.572000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. +
-[    0.580000] Freeing unused kernel memory: ​228k freed+
 - preinit - - preinit -
 Press the [f] key and hit [enter] to enter failsafe mode Press the [f] key and hit [enter] to enter failsafe mode
 - regular preinit - - regular preinit -
-[    7.848000] jffs2: notice: (510) jffs2_build_xattr_subsystem:​ complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 8 of xref (0 dead, 2 orphan) found. 
-switching to jffs2 
 - init - - init -
  
-Please press Enter to activate this console. [    ​8.936000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH +Please press Enter to activate this console. [    ​6.796000] ocf: module license '​BSD'​ taints kernel. 
-[    ​8.956000] Compat-drivers backport release: compat-drivers-2013-01-21-1 +[    6.800000] Disabling lock debugging due to kernel taint 
-[    ​8.960000] Backport based on wireless-testing.git master-2013-02-22 +[    7.092000] IFXOS, Version 1.5.14 (c) Copyright 2009, Lantiq Deutschland GmbH 
-[    ​8.968000] compat.git: wireless-testing.git +[    ​7.120000] Compat-drivers backport release: compat-drivers-2013-01-21-1 
-[    ​9.008000] cfg80211: Calling CRDA to update world regulatory domain +[    ​7.124000] Backport based on wireless-testing.git master-2013-02-22 
-[    ​9.012000] cfg80211: World regulatory domain updated: +[    ​7.132000] compat.git: wireless-testing.git 
-[    ​9.016000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp) +[    ​7.176000] cfg80211: Calling CRDA to update world regulatory domain 
-[    ​9.024000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) +[    ​7.180000] cfg80211: World regulatory domain updated: 
-[    ​9.032000] cfg80211: ​  ​(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) +[    ​7.184000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp) 
-[    ​9.040000] cfg80211: ​  ​(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) +[    ​7.192000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) 
-[    ​9.048000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) +[    ​7.200000] cfg80211: ​  ​(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) 
-[    ​9.052000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) +[    ​7.208000] cfg80211: ​  ​(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) 
-[    ​9.600000] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH +[    ​7.216000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) 
-[    ​9.776000] SCSI subsystem initialized +[    ​7.224000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) 
-  10.300000] Lantiq MIPS24KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH+[    ​7.432000] Lantiq TAPI device driver, version 3.13.0.2, (c) 2001-2010 Lantiq Deutschland GmbH 
 +[    ​7.480000] SCSI subsystem initialized 
 +   7.576000] Lantiq MIPS24KEc MPS driver, version 2.2.2.5, (c) 2006-2010 Lantiq Deutschland GmbH
  
-  10.304000] request_timer(3,​ 0x000001AE, 1)...successful! +   7.580000] request_timer(3,​ 0x000001AE, 1)...successful! 
-  10.312000] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH +   7.588000] Lantiq VMMC device driver, version 1.9.0.3, (c) 2006-2010 Lantiq Deutschland GmbH 
-  10.628000] PCI: Enabling device 0000:​00:​0e.0 (0000 -> 0002) +   7.724000] PCI: Enabling device 0000:​00:​0e.0 (0000 -> 0002) 
-  10.632000] phy0 -> rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from '​RT2860.eeprom'​+   7.736000] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 3572, rf: 0008, rev: 0221. 
-rt2x00 eeprom: ​ board MP-252 is not supported y  10.864000phy0 -> rt2x00lib_request_eeprom_fileError Failed to request EEPROM+[    7.772000] Button Hotplug driver version 0.4.1 
-  10.872000rt2800pciprobe of 0000:00:0e.0 failed with error -2 +   7.988000ip_tables(C) 2000-2006 Netfilter Core Team 
-et +[    8.264000] nf_conntrack version 0.5.0 (958 buckets, 3832 max) 
-  11.032000NETRegistered protocol family 8 +   8.716000IFX MEI Version 5.00.00 
-  11.036000NETRegistered protocol family 20 +[    8.752000] IFXUSBifxusb_hcdversion 3.2 B110801 
-  11.860000IFX MEI Version 5.00.00 +[    9.260000] IFXUSBUSB core #0 soft-reset 
-  11.988000]  +[    9.464000] IFXUSB: USB core #soft-reset 
-  11.988000]  +[    9.464000] ifxusb_hcd ifxusb_hcd: IFX USB Controller 
-  11.988000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4 +   9.472000ifxusb_hcd ifxusb_hcdnew USB bus registered, assigned bus number 1 
-  12.024000ATM1.0.26    ATM (A1) firmware version 0.17 +   9.476000ifxusb_hcd ifxusb_hcdirq 62, io mem 0xbe101000 
-  12.028000ifxmips_atmATM init succeed +   9.484000IFXUSB: Mode Mismatch Interrupt: currently in Host mode 
-[   15.820000] device eth0 entered promiscuous mode +[    9.488000] IFXUSB: Mode Mismatch Interrupt: currently in Host mode 
-[   15.824000] br-lan: port 1(eth0) entered forwarding state +[    9.496000] IFXUSB: Init: Power Port (0) 
-[   15.828000] br-lan: port 1(eth0) entered forwarding state +   9.500000hub 1-0:1.0: USB hub found 
-[   17.832000] br-lan: port 1(eth0) entered forwarding state +   9.504000hub 1-0:1.0: 1 port detected 
-[   27.124000] libphy: Trying 100/FULL+   9.508000] ifxusb_hcd ifxusb_hcd: requested GPIO 227 
 +[    9.572000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4 
 +   9.620000Infineon Technologies DEU driver version 2.0.0  
 +   9.624000] Danube Chip ver. 1.3 or below detected.  
 +[    9.632000] IFX DEU DES initialized ​(multiblock). 
 +[    9.636000] IFX DEU AES initialized (multiblock). 
 +[    9.640000] IFX DEU SHA1 initialized. 
 +[    9.644000] IFX DEU MD5 initialized. 
 +[    9.676000] PTM 1.0.27 ​   PTM (E1) firmware version 0.17 
 +   9.680000ifxmips_ptmPTM init succeed 
 +[    9.724000] Initializing USB Mass Storage driver... 
 +[    9.728000] usbcore: registered new interface driver usb-storage 
 +[    9.732000] USB Mass Storage support registered. 
 +[    9.764000] Error: Driver '​gpio-keys-polled'​ is already registered, aborting... 
 +[   13.396000] device eth0 entered promiscuous mode 
 +[   13.404000] br-lan: port 1(eth0) entered forwarding state 
 +[   13.408000] br-lan: port 1(eth0) entered forwarding state 
 +[   15.412000] br-lan: port 1(eth0) entered forwarding state 
 +[   24.512000] libphy: Trying 100/FULL
  
  
  
-BusyBox v1.19.4 (2013-03-06 06:01:00 IST) built-in shell (ash)+BusyBox v1.19.4 (2013-03-17 20:16:14 IST) built-in shell (ash)
 Enter '​help'​ for a list of built-in commands. Enter '​help'​ for a list of built-in commands.
  
Line 751: Line 788:
           |__| W I R E L E S S   F R E E D O M           |__| W I R E L E S S   F R E E D O M
  ​-----------------------------------------------------  ​-----------------------------------------------------
- ​BARRIER BREAKER (Bleeding Edge, r35893)+ ​BARRIER BREAKER (Bleeding Edge, r36067)
  ​-----------------------------------------------------  ​-----------------------------------------------------
   * 1/2 oz Galliano ​        Pour all ingredients into   * 1/2 oz Galliano ​        Pour all ingredients into
Line 759: Line 796:
  ​-----------------------------------------------------  ​-----------------------------------------------------
 root@OpenWrt:/# ​ root@OpenWrt:/# ​
 +
 </​code>​ </​code>​
 </p> </p>
Line 764: Line 802:
  
 ===== Tags ===== ===== Tags =====
-{{tag>​FastEthernet 4Port 1PHY hwVLAN USB 2USB rt2x00 InternalAntenna ​ADSL2+ ​fxo 64RAM 32Flash MIPS MIPS32 24KEc usb2.0 ​xdsl ejtag ethernet ​adsl 2x2 1usb}}+{{tag>​FastEthernet ​1NIC 1WNIC 4Port hwVLAN USB 2USB rt2x00 InternalAntenna fxo 64RAM 32Flash MIPS MIPS32 24KEc usb2.0 ​ADSL2+ lantiq danube  ​ejtag ethernet 2x2 1usb}}
toh/audiocodes/mp252.1363016031.txt.bz2 · Last modified: 2013/03/11 16:33 (external edit)