Differences

This shows you the differences between two versions of the page.

toh:avm:fritz.box.wlan.3050 [2013/04/13 10:32] (current)
Line 1: Line 1:
 +====== FRITZ!Box WLAN 3050 ======
 +This is one of the older Fritz! boxes that uses the Texas Instruments AR7 SoC.
 +**<color red>This device is not officially supported as of July 2012!</color>**
 +
 +Some work on the AR7 Platform is already done:
 +[[https://dev.openwrt.org/wiki/ar7]]
 +
 +
 +===== Hardware Highlights =====
 +^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^
 +| [[wp>TI-AR7|Texas Instruments AR7]] | 16MiB | ? MiB | 2 | Yes | ? | ? |
 +
 +
 +===== =====
 +
 +| [[doc/howto/generic.overview]] |
 +| [[doc/howto/basic.config]] |
 +
 +===== Installation =====
 +  - -> [[doc:howto:obtain.firmware]]
 +  - -> [[doc:howto:generic.flashing|Install OpenWrt]]
 +
 +==== Flash Layout ====
 +Please check out the article [[doc:techref:Flash Layout]]. It contains an example and a couple of explanations.
 +
 +
 +==== Upgrading OpenWrt ====
 +->  [[doc:howto:generic.sysupgrade]]
 +
 +If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
 +
 +=== LuCI Web Upgrade Process ===
 +
 +  * Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
 +  * Upload image file for sysupgrade to LuCI
 +  * Wait for reboot
 +
 +=== Terminal Upgrade Process ===
 +
 +  * Login as root via SSH on 192.168.1.1
 +  * Use the following commands to upgrade.
 +
 +<code>
 +cd /tmp/
 +wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
 +sysupgrade /tmp/xxx.abc
 +</code>
 +
 +  *If sysupgrade does not support this router, use the following commands.
 +
 +<code>
 +cd /tmp/
 +wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
 +mtd write /tmp/xxx.abc linux && reboot</code>
 +
 +===== Basic configuration =====
 +-> [[doc:howto:basic.config|Basic configuration]] After flashing, proceed with this.\\
 +Set up your Internet connection, configure wireless, configure USB port, etc.
 +
 +
 +
 +==== Failsafe mode ====
 +-> [[doc:howto:generic.failsafe]]
 +
 +==== Buttons ====
 +
 +The Fritz!Box WLAN 3050 has no buttons.
 +
 +===== Hardware =====
 +==== Info ====
 +| **[[wp>Instruction set|Architecture]]:**    | [[wp>MIPS architecture|MIPS32]] |
 +| **Vendor:**          | [[wp>Texas Instruments]] |
 +| **[[doc:techref:Bootloader]]:**    | ? |
 +| **[[doc:hardware:soc|System-On-Chip]]:**  | Texas Instruments AR7 (TNETD7300) |
 +| **[[doc:hardware:cpu|CPU]]/Speed**        |  |
 +| **Flash-Chip:**      | ? |
 +| **Flash size:**      | ? |
 +| **RAM:**            | 16 MiB  |
 +| **Wireless:**        | Texas Instruments TNETW1130 2.4ghz 802.11b/g |
 +| **Ethernet:**        | ?  |
 +| **Internet:**        | ADSL |
 +| **USB:**            | Yes 1 x  |
 +| **[[doc:hardware:port.serial|Serial]]:**          | [[#Serial|?]] |
 +| **[[doc:hardware:port.jtag|JTAG]]:**            | [[#JTAG|Yes]] ? |
 +
 +==== Opening the case ====
 +**Note:** This will void your warranty!
 +
 +To remove the cover use a flat screw driver and turn the Fritz!Box upside down. You will see four square holes on the border of the bottom panel. Now put the screw driver gently in one of these holes and move its top from left to the right when you startet with one of the holes on the left side. If you started with one of the holes on the right side you have to move the top of your screw driver from right to left in that hole.
 +
 +
 +===== Tags =====
 +For some Help with the Tags, please have a look here: [[meta/tags]]
 +
 +{{tag> 2Port 2PHY USB AR7 TI AVM FritzBox 16RAM MIPS MIPS32}}

Back to top

toh/avm/fritz.box.wlan.3050.txt · Last modified: 2013/04/13 10:32 (external edit)