User Tools

Site Tools


toh:avm:fritz.box.wlan.7312

AVM FRITZ!Box 7312

Status

Important: only flash if serial connection available, Ethernet & Wifi not working out of the box

Tested lede-17.01.1-lantiq-xway-FRITZ7320-squashfs-sysupgrade.bin.

  • Boot: working
  • Serial Port: working
  • Wifi: working - has to be enabled via Serial → uci set wireless.radio0.disabled='0' → uci commit
  • DHCP: working (Wifi enabled)
  • Ethernet: not working! → shows up @Boot → device eth0 entered promiscuous mode → IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
  • ADSL: not tested
  • LEDs: not tested
  • LuCI: working, "Flash Firmware" not tested

Info

Architecture: MIPS
Vendor: Lantiq
Bootloader: Adam2
System-On-Chip: Lantiq Xway ARX188 PSB 50812 EL (MIPS 34Kc)
CPU/Speed: 393 MHz
NOR Flash: Macronix MX29GL128EHT2I-90G, 16MiB
RAM Chip: Zentel A4S12D40FTP-G5
RAM Specs: DDR1 64MiB @ 196 MHz
Wireless: Atheros AR9227 b/g/n 2x2
Ethernet: 1x 10/100 Atheros AR8030-A
Switch: none (only 1 ethernet port available)
xDSL: lantiq ADSL2+
USB: no
DECT: dialog semiconductor SC14441
Serial: Yes (2.54mm, unpopulated)
GPIO Buttons: wifi rfkill, dect rfkill
Power: External 5V 1.6A

Opening the case

Towards the back of the device there are two (one on each side) plastic latches.
Those are accessible through the ventilation slots:

Use a thin tool (screw driver or similar) to push them towards the inside of the device.
Once you push it far enough you can open the case a little on one side, then do the same on the other side → the two parts of the case will "fall apart" on their own.

PCB Photos

Serial

port.serial general information about the serial port, serial port cable, etc.

serial mode: 115200,n,8,1,hw

How to connect to the Serial Port of this specific device:

3V3 RX TX GND Software (Linux)
Board square cirlce cirlce cirlce
Siemens Data Cable white blue black sudo screen /dev/ttyUSB0 115200
Cutecom: Rate: 115200, Flow: none, Data: 8, Stop: 1, Parity: none → no input @BoxFTPMode → use screen

Flashing

Backup Firmware

Flash Firmware

Bootlogs

Lede 17.01.1 r3316

flashed: lede-17.01.1-lantiq-xway-FRITZ7320-squashfs-sysupgrade.bin

ROM VER: 1.1.3 CFG 01 (AVM) EVA Revision: 1.1820 Version: 2820 (C) Copyright 2005 AVM Date: Jul 16 2013 Time: 15:30:34 (1) 3 0x90000909-0x9000BD1F [FLASH:] MACRONIX Uniform-Flash 16MB 64 Bytes WriteBuffer [FLASH:](Eraseregion [0] 128 sectors a 128kB) [SYSTEM:] AR9 on 393MHz/393MHz/196MHz <create jffs2 from 0x90D80000 len 0x200000 jffs2_size 32> Atheros 8030 detected Eva_AVM >......................................[ 0.000000] Linux version 4.4.61 (buildbot@builds-02.infra.lede-project.org) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3103-1b51a49) ) #0 Sat Apr 15 16:13:45 2017 [ 0.000000] SoC: AR9 rev 1.2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001954c (MIPS 34Kc) [ 0.000000] MIPS: machine is FRITZ7320 - 1&1 HomeServer [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyLTQ0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00046280 [ 0.000000] Readback ErrCtl register=00046280 [ 0.000000] Memory: 58796K/65536K available (3877K kernel code, 162K rwdata, 620K rodata, 1212K init, 200K bss, 6740K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 393MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 9721189849 ns [ 0.000013] sched_clock: 32 bits at 196MHz, resolution 5ns, wraps every 10922685437ns [ 0.007941] Calibrating delay loop... 260.86 BogoMIPS (lpj=521728) [ 0.042400] pid_max: default: 32768 minimum: 301 [ 0.047261] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.053804] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.066966] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.076628] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.082836] pinctrl core: initialized pinctrl subsystem [ 0.089638] NET: Registered protocol family 16 [ 0.098889] pinctrl-xway 1e100b10.pinmux: Init done [ 0.104939] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: 5, channels: 20 [ 0.164505] Can't analyze schedule() prologue at 80009038 [ 0.179101] PCI host bridge /fpi@10000000/pci@E105400 ranges: [ 0.184759] MEM 0x0000000018000000..0x0000000019ffffff [ 0.190013] IO 0x000000001ae00000..0x000000001affffff [ 0.211861] usbcore: registered new interface driver usbfs [ 0.217416] usbcore: registered new interface driver hub [ 0.222753] usbcore: registered new device driver usb [ 0.228143] PCI host bridge to bus 0000:00 [ 0.232152] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff] [ 0.239060] pci_bus 0000:00: root bus resource [io 0x1ae00000-0x1affffff] [ 0.246004] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.252860] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.261554] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff] [ 0.269388] clocksource: Switched to clocksource MIPS [ 0.275948] NET: Registered protocol family 2 [ 0.281579] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.288482] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.294872] TCP: Hash tables configured (established 1024 bind 1024) [ 0.301505] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.307261] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.313853] NET: Registered protocol family 1 [ 0.326051] gptu: totally 6 16-bit timers/counters [ 0.330930] gptu: misc_register on minor 63 [ 0.335022] gptu: succeeded to request irq 126 [ 0.339505] gptu: succeeded to request irq 127 [ 0.344019] gptu: succeeded to request irq 128 [ 0.348532] gptu: succeeded to request irq 129 [ 0.353046] gptu: succeeded to request irq 130 [ 0.357563] gptu: succeeded to request irq 131 [ 0.363157] Crashlog allocated RAM at address 0x3f00000 [ 0.393368] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.399145] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.414068] io scheduler noop registered [ 0.417899] io scheduler deadline registered (default) [ 0.423861] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc [ 0.432789] console [ttyLTQ0] enabled [ 0.432789] console [ttyLTQ0] enabled [ 0.440037] bootconsole [early0] disabled [ 0.440037] bootconsole [early0] disabled [ 0.449084] lantiq nor flash device: 01000000 at 10000000 [ 0.453260] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.462544] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.467637] Amd/Fujitsu Extended Query version 1.3. [ 0.472617] number of CFI chips: 1 [ 0.476027] 4 ofpart partitions found on MTD device ltq_nor [ 0.481509] Creating 4 MTD partitions on "ltq_nor": [ 0.486337] 0x000000000000-0x000000020000 : "urlader" [ 0.495637] 0x000000020000-0x000000f80000 : "firmware" [ 0.538866] 2 eva-fw partitions found on MTD device firmware [ 0.543109] 0x000000020000-0x00000019cd49 : "kernel" [ 0.550211] 0x0000001a0100-0x000000f80000 : "rootfs" [ 0.556305] mtd: device 3 (rootfs) set to be root filesystem [ 0.560628] 1 squashfs-split partitions found on MTD device rootfs [ 0.566658] 0x000000440000-0x000000f80000 : "rootfs_data" [ 0.574714] 0x000000f80000-0x000000fc0000 : "tffs (1)" [ 0.581056] 0x000000fc0000-0x000001000000 : "tffs (2)" [ 0.596401] libphy: ltq_mii: probed [ 0.598762] eth0: attached PHY [Generic PHY] (phy_addr=1e180000.etop-ff:00, irq=-1) [ 0.607618] wdt 1f8803f0.watchdog: Init done [ 0.614013] NET: Registered protocol family 10 [ 0.624428] NET: Registered protocol family 17 [ 0.627584] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.639964] 8021q: 802.1Q VLAN Support v1.8 [ 0.644196] found entry name -> annex=B [ 0.647963] found entry name -> maca=34:31:C4:56:C9:3F [ 0.652992] found entry name -> macb=34:31:C4:56:C9:40 [ 0.658084] found entry name -> macwlan=34:31:C4:56:C9:41 [ 0.663430] found entry name -> macdsl=34:31:C4:56:C9:42 [ 0.668794] found entry name -> macwlan2=34:31:C4:56:C9:44 [ 0.674138] found entry name -> wlan_key=52492293968187462901 [ 0.696587] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 0.704373] Freeing unused kernel memory: 1212K (80491000 - 805c0000) [ 2.480025] init: Console is alive [ 2.482421] init: - watchdog - [ 5.417657] dwc2 1e101000.ifxhcd: DWC OTG Controller [ 5.421223] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1 [ 5.428522] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000 [ 5.435579] hub 1-0:1.0: USB hub found [ 5.438493] hub 1-0:1.0: 1 port detected [ 5.444610] init: - preinit - [ 6.309522] random: procd: uninitialized urandom read (4 bytes read, 26 bits of entropy available) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 9.598397] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 9.610430] urandom-seed: Seed file not found (/etc/urandom.seed) [ 9.777354] procd: - early - [ 9.779068] procd: - watchdog - [ 10.475474] procd: - ubus - [ 10.634267] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.643231] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.651458] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.659764] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.669277] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.677534] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.686738] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.695635] random: ubusd: uninitialized urandom read (4 bytes read, 43 bits of entropy available) [ 10.704865] procd: - init - Please press Enter to activate this console. [ 11.261869] NET: Registered protocol family 8 [ 11.264766] NET: Registered protocol family 20 [ 11.276570] PPP generic driver version 2.4.2 [ 11.287963] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.304710] IFX MEI Version 5.00.00 [ 11.315577] Infineon CPE API Driver version: DSL CPE API V3.24.4.4 [ 11.328814] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f [ 11.335400] Backport generated by backports.git backports-20160324-13-g24da7d3c [ 11.346811] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.358931] ATM1.0.26 ATM (A1) firmware version 0.16 [ 11.362749] ifxmips_atm: ATM init succeed [ 11.477289] Infineon Technologies DEU driver version 2.0.0 [ 11.483609] IFX DEU DES initialized (multiblock). [ 11.488235] IFX DEU AES initialized (multiblock). [ 11.492099] IFX DEU ARC4 initialized (multiblock). [ 11.496626] IFX DEU SHA1 initialized. [ 11.500211] IFX DEU MD5 initialized. [ 11.503754] IFX DEU SHA1_HMAC initialized. [ 11.507806] IFX DEU MD5_HMAC initialized. [ 11.520048] nf_conntrack version 0.5.0 (937 buckets, 3748 max) [ 11.545735] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002) [ 11.551182] owl-loader 0000:00:0e.0: Direct firmware load for ath9k-eeprom-pci-0000:00:0e.0.bin failed with error -2 [ 11.560439] owl-loader 0000:00:0e.0: Falling back to user helper [ 11.571013] NET: Registered protocol family 24 [ 11.597010] xt_time: kernel timezone is -0000 [ 11.700170] random: ubusd: uninitialized urandom read (4 bytes read, 48 bits of entropy available) [ 12.191464] owl-loader 0000:00:0e.0: fixup device configuration [ 12.198687] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18000000-0x1800ffff] [ 12.204265] PCI: Enabling device 0000:00:0e.0 (0000 -> 0002) [ 12.235132] ath: phy0: eeprom contains invalid mac address: 00:00:00:00:00:00 [ 12.240879] ath: phy0: random mac address will be used: be:10:31:cf:73:7a [ 12.273240] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xb8000000, irq=30 [ 25.438070] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 25.457496] jffs2_build_filesystem(): unlocking the mtd device... done. [ 25.462615] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 28.743338] device eth0 entered promiscuous mode [ 28.768640] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 29.929057] IPv6: ADDRCONF(NETDEV_UP): nas0: link is not ready [ 31.585501] random: nonblocking pool is initialized [ 110.507342] done. [ 110.507863] jffs2: notice: (953) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. BusyBox v1.25.1 () built-in shell (ash) _________ / /\ _ ___ ___ ___ / LE / \ | | | __| \| __| / DE / \ | |__| _|| |) | _| /________/ LE \ |____|___|___/|___| lede-project.org \ \ DE / \ LE \ / ----------------------------------------------------------- \ DE \ / Reboot (17.01.1, r3316-7eb58cf109) \________\/ ----------------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@LEDE:/#


(OEM) EVA Revision: 1.1820 Version: 2820

ROM VER: 1.1.3 CFG 01 (AVM) EVA Revision: 1.1820 Version: 2820 (C) Copyright 2005 AVM Date: Jul 16 2013 Time: 15:30:34 (0) 3 0x90000909-0x9000BD1F [FLASH:] MACRONIX Uniform-Flash 16MB 64 Bytes WriteBuffer [FLASH:](Eraseregion [0] 128 sectors a 128kB) [SYSTEM:] AR9 on 393MHz/393MHz/196MHz Atheros 8030 detected Eva_AVM >.......................... Lantiq xDSL CPE AR9 [ifx_enhance_phy_clock] PLL0_CFG: 0x00b05f23 [ifx_enhance_phy_clock] Setting new PLL0_CFG for external PHY... [ifx_enhance_phy_clock] finished. [ 0.000000] Linux version 2.6.32.61 (jpluschke@EmbeddedVM) (gcc version 4.8.1 (Buildroot 2013.05) ) #1 Tue May 2 10:31:26 CEST 2017 [ 0.000000] phym = 04000000, mem = 04000000, max_pfn = 00004000 [ 0.000000] Reserving memory for CP1 @0xa4000000, size 0x00000000 [ 0.000000] wlan_mem_start = 0x03f9e000 [ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 804aa000) [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001954c (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00003f9e [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00003f9e [ 0.000000] [c55] c55_mem_start = 0xfc0000 [ 0.000000] [module-alloc-by-name] 'modulemem' not in use, use AVM Kernel Config (6758400 bytes, reserved for module mem) [ 0.000000] [module-alloc] use 0x672000 bytes at 0x81081000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16158 [ 0.000000] Kernel command line: console=ttyS1,115200n8r nor_size=16MB ethaddr=34:31:C4:56:C9:3F [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] [avm_cache_set_coherency]: setting cache coherency for HWRevision=189 to write through [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=0004628d [ 0.000000] Readback ErrCtl register=0004628d [ 0.000000] Memory: 52316k/65144k available (3383k kernel code, 12752k reserved, 1388k data, 176k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:181 [ 0.000000] [mips_cpu_irq_init] irq_base 0 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.020000] Calibrating delay loop... 261.32 BogoMIPS (lpj=1306624) [ 0.230000] Security Framework initialized [ 0.230000] Mount-cache hash table entries: 512 [ 0.230000] kernel_init: started [ 0.240000] kernel_init: kernel locked [power_managment_setup] reset 'DSL, DFE, AFE, VOICE, DSLTC, ARC' [power_managment_setup] reset 'LDO' [power_managment_setup] power down 'PPE TC, PPE EMA, LEDC, DFEV1, DFEV0' [power_managment_setup] power down 'MSI1, PDI1 PCIE1 PCIE1_PHY' [power_managment_setup] power down 'USB CTRL' [power_managment_setup] power down 'GPHY' [power_managment_setup] disable power domain 'DSL + DFE' [ 0.280000] NET: Registered protocol family 16 [ 0.290000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.290000] Reboot Status is: Short-PowerOff-Reboot [ 0.300000] [avmnet] [avmnet_cfg_init] Driver version: 6.137.1.1 - Revision 1496:3362 - Mi 8. Mär 12:37:40 CET 2017 [ 0.310000] Lantiq PCI host controller driver, version 1.2.0, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.320000] bio: create slab <bio-0> at 0 [ 0.320000] pci 0000:00:00.0: PME# supported from D1 D2 [ 0.330000] pci 0000:00:00.0: PME# disabled [ 0.330000] NET: Registered protocol family 8 [ 0.330000] NET: Registered protocol family 20 [ 0.340000] NET: Registered protocol family 2 [ 0.340000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.350000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.350000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.360000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.370000] TCP reno registered [ 0.370000] NET: Registered protocol family 1 [ 0.370000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17 ,(c)2009 Infineon Technologies AG [ 0.370000] skb_shared_size:344 [ 0.390000] [bcu_control_interrupt] 'FPI Slave BCU0' Error Interrupt [ 0.390000] Slave BCU[sBCU_EADD]: Error Address Register: 0x17000004 [ 0.390000] Slave BCU[sBCU_EDAT]: Error Data Capture Register: 0x0290030f [ 0.390000] Slave BCU[sBCU_CON] : Control Register: 0x4009ffff [ 0.390000] Slave BCU[sBCU_ECON]: Error Register (0x21be0030): [ 0.390000] FPI Bus Operation Code 0x2 [ 0.390000] FPI Bus Tag Number 0x1 [ 0.390000] FPI Bus Read Signal: passive [ 0.390000] FPI Bus Write Signal: active [ 0.390000] FPI Bus Supervisor Mode: active [ 0.390000] FPI Bus Acknowladge Signal: 0x3 [ 0.390000] FPI Bus Abort: passive [ 0.390000] FPI Bus Ready: active [ 0.390000] FPI Bus Timeout: not pressed [ 0.390000] FPI Bus Error Counter: 48 [ 0.460000] [bcu_control_init] interrupts for BCU installed [ 0.460000] Lantiq CGU driver, version 1.1.32, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.470000] clk-timing: timing:16, ram_refresh_timing:1524, base_ram_refresh_timing:7775 [ 0.480000] smvp_tc_init: tc 0 tcbind 00020000 tcstatus 18102000 [ 0.480000] smvp_tc_init: tc 1 tcbind 00200001 tcstatus 00000400 [ 0.480000] smvp_tc_init: tc 2 tcbind 00400001 tcstatus 00000400 [ 0.480000] smvp_tc_init: tc 3 tcbind 00600001 tcstatus 00000400 [ 0.480000] config3 0x424 MT 1 [ 0.480000] MVPControl 0x2, STLB 0 VPC 1 EVP 0 [ 0.480000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1 [ 0.510000] initcall 0x804b19cc returned with disabled interrupts [ 0.520000] audit: initializing netlink socket (disabled) [ 0.520000] type=2000 audit(0.523:1): initialized [ 0.530000] squashfs: version 3.4 (2008/08/26) Phillip Lougher [ 0.540000] JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.540000] fuse init (API version 7.13) [ 0.550000] msgmni has been set to 102 [ 0.550000] io scheduler noop registered (default) [ 0.550000] system-load 1 loadavg 0.0 0.0 0.0 - 11 tasks:0 % curr:swapper(0 %) max:swapper(0 %, pid:1), readytorun: 1, pgfault 0/s (max 0 avg 0.0) [ 0.570000] [avm_membench_init] [ 0.860000] avm_net_trace: Up and running. [ 0.870000] [loadcontrol] set auto - scale=1 [ 0.870000] [avm] configured: watchdog event debug [ 0.880000] AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: May 2 2017 10:30:27) [ 0.890000] ifx_pmu_init: Major 245 [ 0.890000] Lantiq PMU driver, version 1.2.6, (c) 2001-2013 Lantiq Deutschland GmbH [ 0.900000] Infineon Technologies RCU driver version 1.0.7 [ 0.900000] ttyS0 at MMIO 0x1e100400 (irq = 100) is a PORT_IFX_ASC [ 0.910000] ttyS1 at MMIO 0x1e100c00 (irq = 107) is a PORT_IFX_ASC [ 0.920000] loop: module loaded [ 0.920000] nbd: registered device at major 43 [ 0.940000] Generic platform RAM MTD, (c) 2004 Simtec Electronics [ 0.950000] Platform NOR MTD, (c) AVM 2010 [ 0.950000] [plat_nor_probe]start probe [ 0.950000] [do_map_probe] driver_name=cfi_probe [ 0.960000] mtd-nor: Found 1 x16 devices at 0x0 in 16-bit bank [ 0.970000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.970000] mtd-nor: CFI does not contain boot bank location. Assuming top. [ 0.980000] number of CFI chips: 1 [ 0.980000] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. [ 0.990000] [ifx_jffs2_parser_function] magic 19852003 found @pos 0xd80000, size 2097152 [ 1.010000] [ifx_squashfs_parser_function] magic found @pos 0x179300 [ 1.010000] 6 find_squashfs partitions found on MTD device mtd-nor [ 1.020000] Creating 6 MTD partitions on "mtd-nor": [ 1.020000] 0x000000179300-0x000000f80000 : "rootfs" [ 1.030000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.040000] 0x000000020000-0x000000179300 : "kernel" [ 1.050000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.060000] 0x000000000000-0x000000020000 : "urlader" [ 1.070000] 0x000000f80000-0x000000fc0000 : "tffs (1)" [ 1.070000] 0x000000fc0000-0x000001000000 : "tffs (2)" [ 1.080000] 0x000000d80000-0x000000f80000 : "jffs2" [ 1.080000] mtd-nor mtd-nor: registered mtd device [ 1.090000] tun: Universal TUN/TAP device driver, 1.6 [ 1.090000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.100000] IFX SWITCH API, Version 1.1.8.5 [ 1.100000] SWAPI: Registered character device [switch_api] with major no [81] [ 1.210000] CAPI Subsystem Rev 1.1.2.8 [ 1.210000] AVM PA 4.3.12 2015-11-11 [ 1.220000] AVM PA skb pktinfo at offset 128 size 196 [ 1.220000] [loadcontrol]module avm_pa registered [ 1.230000] IPv4 over IPv4 tunneling driver [ 1.230000] TCP cubic registered [ 1.230000] mcfw: IGMPv3 fast forwarding [ 1.240000] NET: Registered protocol family 10 [ 1.240000] NET: Registered protocol family 17 [ 1.250000] NET: Registered protocol family 8 [ 1.250000] atmpvc_init() failed with -17 [ 1.250000] KOAM is loaded successfully. [ 1.260000] l2tp_core: L2TP core driver, V2.0 [ 1.260000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.270000] l2tp_netlink: L2TP netlink interface [ 1.270000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.280000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.290000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0) [ 1.290000] mount on mtd3 and mtd4 (double buffering) [ 1.300000] TFFS Name Table L [ 1.300000] Adam2 environment variables API installed. [ 1.310000] [simple-profiling]: 4 performance counters implemented, OLD_34K [ 1.310000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.330000] Setup tcs=0x1 current_tc_mask=0x1, reg=0 [ 1.330000] [simple-profiling]: 4 performance counters implemented, OLD_34K [ 1.340000] Enable Performance Counter 1 for Data cache load/store misses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.350000] Setup tcs=0x1 current_tc_mask=0x1, reg=1 [ 1.360000] AVM Simple Profiling enabled Version 3.0 [ 1.360000] {avmnet_cfg_netinit} [ 1.370000] [avmnet] No config found for HWRev 189, HWSubRev 1, Profile-ID 0, trying base config for HWSubRev [ 1.380000] [avmnet] No config found for HWRev 189, HWSubRev 1, trying base config for HWRev [ 1.380000] {avmnet_mac_ar9_init} Init on module mac_ar9_0 called. [ 1.400000] [avmnet] [avmnet_mac_ar9_setup] IFX_AR9_ETH_CTL(0): 0x424001 [ 1.410000] [avmnet] [avmnet_mac_ar9_setup] mac_nr: 0, vlan_reg: 0x4070001 [ 1.540000] [avm_pa_multiplexer_init] start [ 1.540000] [avm_pa_multiplexer_init] init complete [ 1.540000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 34:31:c4:56:c9:3f [ 1.550000] kernel_init: basic setup done [ 1.560000] [squashfs] use lzma compression [ 1.560000] VFS: Mounted root (squashfs filesystem) readonly on device 31:0. [ 1.570000] Freeing unused kernel memory: 176k freed [ 1.620000] trying /sbin/init starting pid 104, tty '/dev/ttyS1': '/etc/init.d/rc.S' tar: removing leading '/' from member names source files in group 0 ... /etc/init.d/S00-signal /etc/init.d/S05-watchdog /etc/init.d/S09-rtc /etc/init.d/S01-head /etc/init.d/S08-tffs /etc/init.d/S02-led /etc/init.d/S09-config [ 4.040000] [module-alloc-by-name] give 0x12000 bytes at 0x81081000 to module 'led_modul_Fritz_Box_HW189' (0x660000 bytes left) [ 4.050000] led_modul_Fritz_Box_HW189: module license ' [ 4.050000] (C) Copyright 2012 by AVM [ 4.050000] ' taints kernel. [ 4.070000] Disabling lock debugging due to kernel taint [ 4.090000] [led_gpio_out_bit] Error: Setting GPIO pin 45 to 1 failed! [ 4.110000] AVM_WATCHDOG: System Init UEberwachung 240 Sekunden mknod: /var/flash/ar7.cfg: File exists P-Defaults: do nothing [ 4.790000] [module-alloc-by-name] give 0x1000 bytes at 0x81093000 to module 'rtc_avm' (0x65f000 bytes left) [ 4.820000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0 [ 4.820000] [avm-rtc]: avm_rtc_probe: register: ret=0x83126c00 [ 4.830000] [avm-rtc]: avm_rtc_probe: success exceute files in group 0 ... /etc/init.d/E05-basemodules group 0 done ... source files in group 1 ... /etc/init.d/S10-html /etc/init.d/S12-default /etc/init.d/S10-vm /etc/init.d/S15-filesys /etc/init.d/S11-config_def /etc/init.d/S17-capi /etc/init.d/S11-piglet /etc/init.d/S17-tam [ 5.060000] [ 5.060000] [avm_debug] redirecting kernel-messages (/dev/debug) [ 5.110000] [module-alloc-by-name] give 0x8000 bytes at 0x81094000 to module 'Piglet_noemif' (0x657000 bytes left) [ 5.110000] [module-alloc-by-name] 0x8000 bytes used, 0xB510 bytes expected [ 5.130000] [piglet]use default-settings (1 gpio from hw_config) [ 5.240000] [piglet]patch_dectfw: C030C000, totallen = 44825(AF19) [ 5.240000] [piglet]patch_dectfw: patch_adress: A0 max_len: 26 with Version 2 Len: 17 [ 5.240000] [piglet]patch_dectfw: RFPI tag found 0271929880 [ 5.240000] [piglet]patch_dectfw: dectmode 1 [ 5.240000] [piglet]dect_loader144xx: slow-bootmode <FE>* *************************************************************************************** [ 8.530000] [piglet]dect144xx_file_process: upload of '/lib/modules/dectfw_secondlevel_441.hex' successfull [ 10.540000] [piglet]TDM: FS: 8005 Hz CLK: 1023995 Hz [ 10.750000] system-load 100 % loadavg 0.15 0.3 0.1 - 22 tasks:24 % curr:mount(0 %) max:init(14 %, pid:1), readytorun: 1, pgfault 2299/s (max 1 avg 1.0) [jffs2] Mount /data success (mtd5 size 2097152) [jffs2] write env variable jffs2_size to 32 [ 10.980000] [module-alloc-by-name] give 0x5F000 bytes at 0x8109C000 to module 'pcmlink' (0x5F8000 bytes left) [ 10.980000] [module-alloc-by-name] 0x5F000 bytes used, 0x685E4 bytes expected [ 11.110000] [pcmlink]VPE-Interface: base 0xFC0000, maxsize 131072, host-irq 142 [ 11.490000] [module-alloc-by-name] give 0xA2000 bytes at 0x810FB000 to module 'isdn_fbox_fon5' (0x556000 bytes left) [ 11.490000] [module-alloc-by-name] 0xA2000 bytes used, 0xB60DC bytes expected [ 11.600000] [pcmlink]chrony-support [ 11.600000] VPE loader: loading segment 1 to 80FC0000 (14000 bytes) elf loaded [ 11.600000] vpe_run: tc 1 start-addr 80FC0000 [ 11.600000] vpe_run: tc 1 tcstatus 18000400 tcbind 00200001 MVPCONTROL 00000002 vpeopt 00000000 [ 12.620000] [isdn]PCMLINK: Version 7.511 (isdn: 3163) Codecslots=6 Slics=1 Pots=1 TE=0 NT=0 DECT=4 (IA3222) no HwCross DSP-EC: 2 [ 13.050000] [module-alloc-by-name] give 0x54000 bytes at 0x8119D000 to module 'capi_codec' (0x502000 bytes left) [ 13.050000] [module-alloc-by-name] 0x54000 bytes used, 0x5D6B0 bytes expected capicodec_init() [capi_codec] support fax [capi_codec] support Codecs [ 13.080000] : Codecs_Init register a /dev/debug handler [ 13.260000] [module-alloc-by-name] give 0x3A000 bytes at 0x811F1000 to module 'avm_dect' (0x4C8000 bytes left) [ 13.260000] [module-alloc-by-name] 0x3A000 bytes used, 0x42320 bytes expected [ 13.300000] [module-alloc-by-name] give 0x3000 bytes at 0x8122B000 to module 'dect_io' (0x4C5000 bytes left) [ 13.300000] [module-alloc-by-name] 0x3000 bytes used, 0x447C bytes expected TAM: create JFFS2 directory /data/tam exceute files in group 1 ... /etc/init.d/E15-device mknod led c 242 mknod tffs c 243 mknod avm_power c 252 mknod debug c 248 mknod avm_event c 249 mknod capi_oslib c 68 mknod dect_io c 239 / group 1 done ... source files in group 2 ... /etc/init.d/S21-udev exceute files in group 2 ... group 2 done ... source files in group 3 ... /etc/init.d/S30-ledcfg exceute files in group 3 ... group 3 done ... source files in group 4 ... /etc/init.d/S40-swap /etc/init.d/S44-hostname /etc/init.d/S48-configd /etc/init.d/S42-ptest /etc/init.d/S46-usb Jan 1 01:00:13 udevd[364]: specified group 'tty' unknown Jan 1 01:00:13 udevd[364]: specified group 'dialout' unknown Jan 1 01:00:13 udevd[364]: specified group 'kmem' unknown Jan 1 01:00:13 udevd[364]: specified group 'video' unknown Jan 1 01:00:13 udevd[364]: specified group 'audio' unknown Jan 1 01:00:13 udevd[364]: specified group 'lp' unknown Jan 1 01:00:13 udevd[364]: specified group 'disk' unknown Jan 1 01:00:13 udevd[364]: specified group 'floppy' unknown Jan 1 01:00:13 udevd[364]: specified group 'cdrom' unknown [ 13.860000] [module-alloc-by-name] give 0x1000 bytes at 0x8122E000 to module 'lzo_compress' (0x4C4000 bytes left) [ 13.860000] [module-alloc-by-name] 0x1000 bytes used, 0x1878 bytes expected [ 13.860000] [module-alloc-by-name] give 0x1000 bytes at 0x8122F000 to module 'lzo_decompress' (0x4C3000 bytes left) [ 13.860000] [module-alloc-by-name] 0x1000 bytes used, 0x1938 bytes expected Jan 1 01:00:13 udevd[364]: specified group 'tape' unknown <6>udev: starting version 151 [ 13.930000] [module-alloc-by-name] give 0x4000 bytes at 0x81230000 to module 'ramzswap' (0x4BF000 bytes left) [ 13.930000] [module-alloc-by-name] 0x4000 bytes used, 0x58E0 bytes expected [ 13.960000] ramzswap: /dev/ramzswap0 initialized: disksize_kb=8192mknod: /dev/ramzswap0: File exists [ 14.000000] Adding 8184k swap on /dev/ramzswap0. Priority:-1 extents:1 across:8184k SS exceute files in group 4 ... /etc/init.d/E40-dsl /etc/init.d/E46-net /etc/init.d/E47-voip [dsl sus] dsl line test calib factory file available [dsl get xtse] ANNEX=B [dsl get xtse] setting Annex B and J [dsl get xtse] 10 00 10 40 00 04 01 00 [dsl sus] starting ar9 dsp... [dsl sus] ANNEX=B DIAGNOSE=no [ 14.920000] [module-alloc-by-name] give 0x9000 bytes at 0x81234000 to module 'ifxmips_mei' (0x4B6000 bytes left) [ 14.920000] [module-alloc-by-name] 0x9000 bytes used, 0xBC1C bytes expected [dsl mei] Lantiq MEI driver version: 5.03.00 [dsl mei] Lantiq MEI driver global debug_level: 0 [dsl sus] loaded ar9 mei driver: ifxmips_mei.ko with params: [ 15.160000] [module-alloc-by-name] give 0x4D000 bytes at 0x8123D000 to module 'drv_dsl_cpe_api' (0x469000 bytes left) [ 15.160000] [module-alloc-by-name] 0x4D000 bytes used, 0x568A8 bytes expected [dsl drv] Lantiq CPE API Driver version: DSL CPE API V4.9.2.1 [dsl drv] Predefined debug level: 4 [dsl drv] dynamically registered major number 238 for drv_dsl_cpe_api [dsl sus] loaded ar9 dsl driver: drv_dsl_cpe_api.ko with params: [dsl sus] created ar9 dsl device node /dev/dsl_ar9 (major: 238 , minor: 0) [dsl sus] created ar9 mei device node /dev/ifx_mei (major: 105 , minor: 0) [dsl sus] started dsl_control (configuration: -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.sh ) nohup: appending output to nohup.out 0 [dsl sus] started dsl_monitor [dsl sus] ....ar9 dsp started [ 17.090000] [module-alloc-by-name] give 0x138000 bytes at 0x8128A000 to module 'kdsldmod' (0x331000 bytes left) [ 17.090000] [module-alloc-by-name] 0x138000 bytes used, 0x16CDE0 bytes expected [ 17.250000] kdsldmod: init start (Mar 8 2017 12:59:33) sizeof(struct sk_buff)=440 [ 17.260000] userman: device registerd (userman_url) with major=232 <6>kdsld: ttychannel: ldisc 8 registered [ 17.260000] PCP_NL: PCP netlink interface (multicast group 1) [ 17.260000] kdsldmod: init done (Mar 8 2017 12:59:33) /etc/init.d/E46-net: /etc/init.d/rc.net: line 527: l2tpv3d: not found Jan 1 01:00:18 ctlmgr[579]: pcpc_create_ctx: no pcpserver found Jan 1 01:00:19 upnpd[585]: starting ... 1970-01-01 01:00:19 upnpd[585]: ready (0sec) [ 20.950000] system-load 100 % loadavg 0.36 0.8 0.3 - 49 tasks:32 % curr:mtdblockd(8 %) max:ctlmgr(12 %, pid:581), readytorun: 2, pgfault 4266/s (max 2 avg 1.0) Jan 1 01:00:21 multid[595]: startup ($Revision: 29113 $$CompileDate: Mar 8 2017 12:55:54 $) Jan 1 01:00:21 multid[595]: starting ... Jan 1 01:00:21 multid[597]: HWRevision=189 Jan 1 01:00:21 multid[597]: l2tpcfg_cfg2buf: size 161 Jan 1 01:00:21 multid[597]: opt_without_tr069discover=0, AR7CFG->vinax_hsi_lan_ports=, multid.use_vinax=0, multid.tcom_targetarch=0, is_eth_switch_installed()=0, multid.cpmac_no_ata_possible=0, pppoeiface=nuller Jan 1 01:00:21 multid[597]: setup_cpmac: get_pppoeiface=???, multid.wan_iface_name=eth0 Jan 1 01:00:21 multid[597]: bridge_configured: is_vinax=0, is_ata=0, bridge_with_switch_separation=1 Jan 1 01:00:21 multid[597]: bridge_configured: nqos_bridge_active=0, bridge_port_set=0x0, igmp_flt_portset=0x0 Jan 1 01:00:21 multid[597]: bridge_configured: portnumber=1, portbit=0x1, mode=0 Jan 1 01:00:21 multid[597]: bridge_configured: other_bridge_active=0, effective bridge_port_set=0x0 Jan 1 01:00:21 multid[597]: ipv6_remove_addresses_for(eth0) Jan 1 01:00:21 multid[597]: create new bridge lan [avm_power] eth: port 0 force normal CON t0 [ 22.220000] ADDRCONF(NETDEV_UP): lan: link is not ready [ 22.220000] ADDRCONF(NETDEV_UP): lan: link is not ready Jan 1 01:00:22 ctlmgr[581]: WLANLIB: wlan_plugin_init:630: svn revision 2555 [ 22.570000] DSP: XDU=1( D1 ) OVR=0 MIPS_OVR=0 [ 22.860000] ADDRCONF(NETDEV_UP): eth0: link is not ready Jan 1 01:00:22 ctlmgr[581]: WLANLIB: weak_wlan_check:73: Missing weak 'wlan_get_known_wlan_macs'. Jan 1 01:00:22 ctlmgr[581]: WLANLIB: weak_wlan_check:76: Missing weak 'process_wlanmail'. Jan 1 01:00:22 ctlmgr[581]: WLANLIB: weak_wlan_check:79: Missing weak 'wlan_enabled_changed'. Jan 1 01:00:22 ctlmgr[581]: WLANLIB: weak_wlan_check:82: Missing weak 'wlan_wcfgutil_set_output'. Jan 1 01:00:22 ctlmgr[581]: WLANLIB: weak_wlan_check:83: Missing weak 'wlan_wcfgutil_set_dbg_level'. Jan 1 01:00:22 multid[597]: remove_iface_from_other_linuxbridges: iface=eth0, br_exclude=lan Jan 1 01:00:22 multid[597]: br_get_list1: (AVM) num=1 Jan 1 01:00:22 multid[597]: list[0]=lan Jan 1 01:00:22 multid[597]: add eth0 to linuxbridge(2) lan [ 22.970000] device eth0 entered promiscuous mode Jan 1 01:00:22 multid[597]: create new bridge guest [ 24.000000] ADDRCONF(NETDEV_UP): guest: link is not ready [ 24.000000] ADDRCONF(NETDEV_UP): guest: link is not ready Jan 1 01:00:24 multid[597]: ipv6_remove_addresses_for(lan) Jan 1 01:00:24 multid[597]: ipv6_remove_addresses_for(guest) Jan 1 01:00:24 multid[597]: set_igmp_bridge_flt: Jan 1 01:00:24 multid[597]: set_igmp_bridge_flt: sum portmap=0x0 Jan 1 01:00:24 multid[597]: set_igmp_bridge_flt: reset igmp netfilter Jan 1 01:00:24 multid[597]: snooping for lan? 1 Jan 1 01:00:24 multid[597]: multicast_snooping for bridge lan = 1 Jan 1 01:00:24 multid[597]: snooping for lan:0? 1 Jan 1 01:00:24 multid[597]: snooping for guest? 1 Jan 1 01:00:24 multid[597]: multicast_snooping for bridge guest = 1 Jan 1 01:00:24 multid[597]: mrouter: using IGMPv3 for upstream interface dsl Jan 1 01:00:24 multid[597]: mrouter: using IGMPv3 for other interfaces Jan 1 01:00:24 multid[597]: resolv.conf with 127.0.0.1 written Jan 1 01:00:24 multid[597]: 125: enterprise 3561 suboption 4 op=0x2ae8c440 Jan 1 01:00:24 multid[597]: 125: enterprise 3561 suboption 5 op=0x2ae8c440 Jan 1 01:00:24 multid[597]: 125: enterprise 3561 suboption 6 op=0x2ae8c440 Jan 1 01:00:24 multid[597]: DHCPD: TR111 enabled Jan 1 01:00:24 multid[597]: DHCPD on lan Jan 1 01:00:24 multid[597]: DHCPD on lan:0 skipped, is virtual interface Jan 1 01:00:24 multid[597]: DHCPD on guest Jan 1 01:00:24 multid[597]: open(/dev/userman) - No such file or directory (2) Jan 1 01:00:24 multid[597]: open(/dev/userman) - No such file or directory (2) Jan 1 01:00:24 multid[597]: neighbour: real mac for Amigo changed from 18:cf:5e:0b:72:e3 to 00:50:b6:1a:3c:84 Jan 1 01:00:24 multid[597]: neighbour: real mac for BNELKA-DE changed from a4:4e:31:3e:33:20 to e4:b3:18:9c:65:d5 Jan 1 01:00:24 multid[597]: neighbour: real mac for Tommys-iPhone changed from b8:e8:56:f1:d3:52 to b4:8b:19:70:a7:c0 Jan 1 01:00:24 multid[597]: neighbour: real mac for iPhone-BUN changed from dc:41:5f:b4:44:f4 to b0:48:1a:93:27:4e [ 24.280000] [led_gpio_out_bit] Error: Setting GPIO pin 45 to 1 failed! [ 24.280000] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 24.280000] lan: port 1(eth0) entered forwarding state [ 24.280000] lan: port 1(eth0) entered forwarding state [ 24.280000] ADDRCONF(NETDEV_CHANGE): lan: link becomes ready Jan 1 01:00:24 multid[597]: neighbour: real mac for iPhonevtzGrosch changed from 4c:8d:79:66:9d:0e to 60:d9:c7:09:52:dc [ 24.300000] [dma_device_write] auto open tx_chan_no:0 [ 24.300000] Added 83AA7090M recipient for mc group 825D5530I6 (vid: 0), now 1 recipientsJan 1 01:00:24 multid[597]: add_jasonii_dns_rebind_protection_exceptions: free list Jan 1 01:00:24 multid[597]: Warning: dnsd_start: no dns server added Jan 1 01:00:24 multid[597]: interface lo new. Jan 1 01:00:24 multid[597]: mrouter: lan: vif 0 if_index 5 Jan 1 01:00:24 multid[597]: interface lo up. Jan 1 01:00:24 multid[597]: interface lo carrier up Jan 1 01:00:24 multid[597]: interface tunl0 new. Jan 1 01:00:24 multid[597]: interface eth0 new. Jan 1 01:00:24 multid[597]: remove_iface_from_other_linuxbridges: iface=eth0, br_exclude=lan Jan 1 01:00:24 multid[597]: br_get_list1: num=2 Jan 1 01:00:24 multid[597]: list[0]=lan Jan 1 01:00:24 multid[597]: list[1]=guest Jan 1 01:00:24 multid[597]: br_get_interfaces(guest)=0 Jan 1 01:00:24 multid[597]: add eth0 to linuxbridge(2) lan Jan 1 01:00:24 multid[597]: setup_mc_mdb: bridgename=lan etherdevname=eth0 (239.255.255.250) Jan 1 01:00:24 multid[597]: interface eth0 up. Jan 1 01:00:24 multid[597]: interface eth0 carrier up Jan 1 01:00:24 multid[597]: setup_mc_mdb: bridgename=lan etherdevname=eth0 (239.255.255.250) Jan 1 01:00:24 multid[597]: interface adsl new. Jan 1 01:00:24 multid[597]: interface lan new. Jan 1 01:00:24 multid[597]: DHCPD on lan Jan 1 01:00:24 multid[597]: interface lan up. Jan 1 01:00:24 multid[597]: DHCPD on lan Jan 1 01:00:24 multid[597]: interface lan carrier up Jan 1 01:00:24 multid[597]: interface guest new. Jan 1 01:00:24 multid[597]: interface guest up. Jan 1 01:00:24 multid[597]: DHCPD on guest Jan 1 01:00:24 multid[597]: mrouter: lan: vif 0 if_index 5 Jan 1 01:00:24 multid[597]: mrouter: guest: vif 1 if_index 6 Jan 1 01:00:24 multid[597]: ipv6_remove_addresses_for(lan) Jan 1 01:00:24 multid[597]: ipv6_remove_addresses_for(guest) 1970-01-01 01:00:24 multid[595]: ready (3sec) Jan 1 01:00:24 multid[597]: verbose: DISABLED Jan 1 01:00:24 ddnsd[651]: startup ($Revision: 1.31 $$CompileDate: Mar 8 2017 12:55:54 $) Jan 1 01:00:24 ddnsd[651]: starting ... Jan 1 01:00:24 ddnsd[653]: DDNS: no valid accounts 1970-01-01 01:00:24 ddnsd[651]: [651]: Daemon start failed (0sec) Jan 1 01:00:24 ddnsd[653]: [653] Start failed FATAL: ddnsd not running after started Jan 1 01:00:25 pcpd[655]: startup (Mar 8 2017 12:55:52) Jan 1 01:00:25 pcpd[655]: starting ... Jan 1 01:00:25 pcpd[657]: Local v4 address: 192.168.178.1 Jan 1 01:00:25 pcpd[657]: verbose: DISABLED 1970-01-01 01:00:25 pcpd[655]: ready (0sec) Jan 1 01:00:25 upnpdevd[659]: startup ($Revision: 1.11 $$CompileDate: Mar 8 2017 12:55:54 $) Jan 1 01:00:25 upnpdevd[659]: starting ... Jan 1 01:00:25 upnpdevd[661]: CONFIG_LOGD disabled: No UPnP-Device for avmlogd 1970-01-01 01:00:25 upnpdevd[659]: ready (0sec) Jan 1 01:00:25 upnpdevd[661]: verbose: DISABLED rc.wlan: Start WLAN... [ 25.630000] Added 83B2F090M recipient for mc group 82447E30I6 (vid: 0), now 1 recipientsWLAND:[00670]:01:00.25/[25.79]:BUILD: Mar 8 2017, 13:08:39 [ 26.900000] [module-alloc-by-name] give 0x20000 bytes at 0x813C2000 to module 'aae' (0x311000 bytes left) [ 26.900000] [module-alloc-by-name] 0x20000 bytes used, 0x262B0 bytes expected [ 27.050000] [wlan_config] Given config is: [ 27.050000] [wlan_config] hw_interface=0 chip_type=3 (kiwi) offload=1 (non) [ 27.050000] [wlan_config] hwrev=189 hwsubrev=1 maca=34:31:C4:56:C9:3F [ 27.050000] [wlan_eeprom] Calibration data blocks found = 1 [ 27.050000] [wlan_eeprom] EEPROM #1, type "AR92x7": [ 27.050000] [wlan_eeprom] regDmn=0x8114 - patching to 0 [ 27.050000] [wlan_eeprom] Build with ART 0.9b21 [ 27.050000] avm_net_trace: New net trace device 'WLAN Management Traffic' registered with minor 128. Jan 1 01:00:27 dsld[673]: startup ($Revision: 28389 $$CompileDate: Mar 8 2017 12:56:19 $) Jan 1 01:00:27 dsld[673]: set_preconfig1 Jan 1 01:00:27 dsld[673]: sync_group in ar7.cfg: Jan 1 01:00:27 dsld[673]: sync_group:sync_dsl(enabled=1), nr=0 Jan 1 01:00:27 dsld[673]: vcc:1/32 Jan 1 01:00:27 dsld[673]: dsliface:internet Jan 1 01:00:27 dsld[673]: dsliface:mstv Jan 1 01:00:27 dsld[673]: vcc:1/35 Jan 1 01:00:27 dsld[673]: dsliface:voip Jan 1 01:00:27 dsld[673]: sync_group: dsl Jan 1 01:00:27 dsld[673]: sync_dsl is igd_device Jan 1 01:00:27 dsld[673]: set_preconfig2 Jan 1 01:00:27 dsld[673]: add_vcc_connection: 1/32, sync_group=dsl Jan 1 01:00:27 dsld[673]: add_vcc_connection: 1/35, sync_group=dsl Jan 1 01:00:27 dsld[673]: starting ... Jan 1 01:00:27 dsld[693]: DSL Mac 34:31:c4:56:c9:42 Jan 1 01:00:27 dsld[693]: VOIP Mac 34:31:c4:56:c9:43 Jan 1 01:00:27 dsld[693]: VCC2 Mac 34:31:c4:56:c9:44 Jan 1 01:00:27 dsld[693]: VCC3 Mac 34:31:c4:56:c9:40 <3>kdsld: kdsld_vcc_preunregister: * [ 27.210000] kdsld: nr_ipv4 0 nr_ipv6 0 nr_vpn 0 Jan 1 01:00:27 dsld[693]: sync_group(prepare_interfaces): dsl: inet_nr=0 Jan 1 01:00:27 dsld[693]: nach prepare_interfaces: dsld.dsliface_default_inet_nr=0, dsld.dsliface_voip_nr=1 Jan 1 01:00:27 dsld[693]: get_queueindex: none: not found Jan 1 01:00:27 dsld[693]: get_queueindex: none: not found Jan 1 01:00:27 dsld[693]: queue 0: prio 0 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 1: prio 10 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 2: prio 20 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 3: prio 30 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 4: prio 100 weight 90 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 5: prio 100 weight 10 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: queue 6: prio 200 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:27 dsld[693]: appl 0: sip-appl result 1 Jan 1 01:00:27 dsld[693]: classifer: local "localmark sip" result 1 Jan 1 01:00:27 dsld[693]: classifer: local "localmark rtp" result 1 Jan 1 01:00:27 dsld[693]: classifer: local "localmark sipdns,ntpdns,tr069dns,tr069" result 2 Jan 1 01:00:27 dsld[693]: classifer: local "localmark webdav" result 3 Jan 1 01:00:27 dsld[693]: classifer: lan "ip.proto IPv6-ICMP" result 2 Jan 1 01:00:27 dsld[693]: classifer: lan "ip.proto icmp" result 2 Jan 1 01:00:27 dsld[693]: classifer: lan "udp.dport 53" result 2 Jan 1 01:00:27 dsld[693]: classifer: lan "udp.dport 5060" result 4 Jan 1 01:00:27 dsld[693]: classifer: local "localmark sip_internet" result 1 Jan 1 01:00:27 dsld[693]: classifer: local "localmark rtp_internet" result 1 Jan 1 01:00:27 dsld[693]: classifer: local "localmark dns" result 2 Jan 1 01:00:27 dsld[693]: classifer: lan "tcp.dport 5060" result 4 Jan 1 01:00:27 dsld[693]: classifer: lan "udp.dport 43962 ip.tos 0x60" result 5 Jan 1 01:00:27 dsld[693]: classifer: lan "udp.dport 47806 ip.tos 0x60" result 5 Jan 1 01:00:27 dsld[693]: classifer: local "localmark igmp ip.tos 0x60" result 6 Jan 1 01:00:27 dsld[693]: classifer: local "localmark igmp" result 7 Jan 1 01:00:27 dsld[693]: classifer: lan "udp.dport 123 ip.tos 0x60" result 8 Jan 1 01:00:27 dsld[693]: classifer: lan "tcp.dport 80 ip.tos 0x60" result 8 Jan 1 01:00:27 dsld[693]: result 0: tos 65535 vprio 65535 queue 5 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 1: tos 65535 vprio 65535 queue 2 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 2: tos 65535 vprio 65535 queue 1 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 3: tos 65535 vprio 65535 queue 6 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 4: tos 65535 vprio 65535 queue 2 appl 0 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 5: tos 96 vprio 65535 queue 1 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 6: tos 128 vprio 4 queue 0 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 7: tos 0 vprio 0 queue 0 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: result 8: tos 128 vprio 65535 queue 1 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:27 dsld[693]: interface lo added. Jan 1 01:00:27 dsld[693]: interface lo up. Jan 1 01:00:27 dsld[693]: interface lo carrier_up. Jan 1 01:00:27 dsld[693]: interface tunl0 added. Jan 1 01:00:27 dsld[693]: interface eth0 added. Jan 1 01:00:27 dsld[693]: interface eth0 up. Jan 1 01:00:27 dsld[693]: interface eth0 carrier_up. Jan 1 01:00:27 dsld[693]: interface adsl added. Jan 1 01:00:27 dsld[693]: interface lan added. Jan 1 01:00:27 dsld[693]: interface lan up. Jan 1 01:00:27 dsld[693]: interface lan carrier_up. Jan 1 01:00:27 dsld[693]: interface guest added. Jan 1 01:00:27 dsld[693]: interface guest up. Jan 1 01:00:27 dsld[693]: start register_vccs_and_ifaces_on_kdsld for sync_dsl Jan 1 01:00:27 dsld[693]: setup_dslchannel: ifname= Jan 1 01:00:27 dsld[693]: kdsld_preregister_vcc: predsl1 <3>kdsld: kdsld_vcc_preregister: predsl1 <3>kdsld: kdsld_vcc_preregister: vcc->ifaces=(null) Jan 1 01:00:27 dsld[693]: kdsld_preregister_vcc: kdsld_vccidx=0 [ 27.510000] kdsld: voip: set_rcv_ipaddr: 192.168.178.1 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=3 Jan 1 01:00:27 dsld[693]: udslcb_created: nr=1 (sync_dsl) Jan 1 01:00:27 dsld[693]: udsliface->attached=1(0x44ec00) Jan 1 01:00:27 dsld[693]: setup_dslchannel: ifname= Jan 1 01:00:27 dsld[693]: kdsld_preregister_vcc: predsl2 <3>kdsld: kdsld_vcc_preregister: predsl2 <3>kdsld: kdsld_vcc_preregister: vcc->ifaces=(null) Jan 1 01:00:27 dsld[693]: kdsld_preregister_vcc: kdsld_vccidx=1 [ 27.540000] kdsld: internet: set_rcv_ipaddr: 192.168.178.1 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=3 Jan 1 01:00:27 dsld[693]: udslcb_created: nr=0 (sync_dsl) Jan 1 01:00:27 dsld[693]: udsliface->attached=1(0x44eb8c) [ 27.540000] kdsld: IPv6: mstv: link local fe80::3631:c4ff:fe56:c944 remote :: [ 27.540000] kdsld: mstv: set_rcv_ipaddr: 192.168.178.1 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=3 Jan 1 01:00:27 dsld[693]: udslcb_created: nr=2 (sync_dsl) Jan 1 01:00:27 dsld[693]: udsliface->attached=1(0x44ec74) Jan 1 01:00:27 dsld[693]: udslinterface_set_internet_forwardrules: FORWARDRULES_INTERNET_NORMAL=13 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=13 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=10 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=11 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=12 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=13 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=10 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=11 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=12 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=13 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=10 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=11 Jan 1 01:00:27 dsld[693]: udslinterface_set_forwardrules: group=12 [ 27.610000] kdsld: route-dsl: set_snd_ipaddr: 192.168.180.1 [ 27.610000] kdsld: route-dsl: set_rcv_ipaddr: 192.168.180.1 Jan 1 01:00:27 dsld[693]: voip_backup: enabled 1970-01-01 01:00:27 dsld[673]: ready (0sec) Jan 1 01:00:27 dsld[693]: verbose: DISABLED Notify type: DSL_INTERFACE_STATUS Jan 1 01:00:30 telefon[800]: use clock_gettime(CLOCK_MONOTONIC)! Jan 1 01:00:30 telefon[800]: No S0NT! Jan 1 01:00:30 telefon[800]: NoOldMSNNames telefon: SIGCHLD PID 840 received! Jan 1 01:00:30 telefon[800]: WARNING No config file '/var/flash/fx_def' ! [ 31.080000] system-load 100 % loadavg 0.84 0.19 0.6 - 61 tasks:49 % curr:telefon(5 %) max:ctlmgr(27 %, pid:581), readytorun: 2, pgfault 4668/s (max 3 avg 1.0) Jan 1 01:00:31 telefon[800]: INFO No MOH file '/var/flash/fx_moh' ! [ 31.760000] [module-alloc-by-name] give 0x21000 bytes at 0x813E2000 to module 'krtp' (0x2F0000 bytes left) [ 31.760000] [module-alloc-by-name] 0x21000 bytes used, 0x2670C bytes expected [ 32.290000] [module-alloc-by-name] give 0x1000 bytes at 0x81403000 to module 'sch_tbf' (0x2EF000 bytes left) [ 32.290000] [module-alloc-by-name] 0x1000 bytes used, 0x263C bytes expected [ 32.410000] [module-alloc-by-name] give 0x2000 bytes at 0x81404000 to module 'sch_llq' (0x2ED000 bytes left) [ 32.410000] [module-alloc-by-name] 0x2000 bytes used, 0x3714 bytes expected [ 32.420000] sch_llq: May 2 2017 10:30:56 [ 32.500000] [module-alloc-by-name] give 0x2000 bytes at 0x81406000 to module 'sch_sfq' (0x2EB000 bytes left) [ 32.500000] [module-alloc-by-name] 0x2000 bytes used, 0x28BC bytes expected telefon: SIGCHLD PID 926 received! Jan 1 01:00:32 telefon[899]: NoOldMSNNames Jan 1 01:00:33 dsld[693]: !!!!!!!!!!!!!!!!!route_add: default: metric=2, iface=dsl mknod: /var/flash/fx_def: File exists telefon: SIGCHLD PID 939 received! Jan 1 01:00:33 telefon[899]: WARNING No config file '/var/flash/fx_def' ! Jan 1 01:00:33 voipd[918]: starting ... Jan 1 01:00:34 dsld[693]: udslinterface_set_forwardrules: group=0 1970-01-01 01:00:34 voipd[918]: ready (1sec) group 4 done ... source files in group 5 ... exceute files in group 5 ... group 5 done ... source files in group 6 ... exceute files in group 6 ... group 6 done ... source files in group 7 ... /etc/init.d/S73-capitcp /etc/init.d/S76-media /etc/init.d/S75-inetd /etc/init.d/S79-boxnotify [ 35.140000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 255 -> 0 Jan 1 01:00:35 ddnsd[975]: startup ($Revision: 1.31 $$CompileDate: Mar 8 2017 12:55:54 $) Jan 1 01:00:35 ddnsd[975]: starting ... Jan 1 01:00:35 ddnsd[1012]: DDNS: no valid accounts Jan 1 01:00:35 ddnsd[1012]: [1012] Start failed Jan 1 01:00:35 pcpd[1017]: already running exceute files in group 7 ... group 7 done ... source files in group 8 ... /etc/init.d/S85-apps Jan 1 01:00:35 telefon[899]: Stop DECT [ 35.900000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 0 -> 0 [ 35.900000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 0 -> 0 exceute files in group 8 ... group 8 done ... source files in group 9 ... /etc/init.d/S99-tail rc.wlan: Start WLAN... rc.wlan start: WLAN daemon already running run_clock demon started AVM_WATCHDOG: System Init UEberwachung abgeschlossen (208070 ms noch verfuegbar) [ 36.120000] SysRq : Changing Loglevel Loglevel set to 4 Info: have to stop cat /dev/debug. notifyd[1030]: received signal Hangup pbd[793]: received signal Hangup Please press Enter to activate this console. Jan 1 01:00:40 usermand[1144]: starting ... Jan 1 01:00:40 contfiltd[1158]: starting ... Jan 1 01:00:49 ddnsd[1399]: startup ($Revision: 1.31 $$CompileDate: Mar 8 2017 12:55:54 $) Jan 1 01:00:49 ddnsd[1399]: starting ... Jan 1 01:00:49 ddnsd[1401]: DDNS: no valid accounts Jan 1 01:00:49 ddnsd[1401]: [1401] Start failed Jan 1 01:00:49 pcpd[1403]: already running telefon: SIGCHLD PID 1043 received! telefon: SIGCHLD PID 934 received! starting pid 1068, tty '/dev/ttyS1': '-/bin/sh' BusyBox v1.20.2 (2015-07-07 11:46:25 CEST) built-in shell (ash) Enter 'help' for a list of built-in commands. ermittle die aktuelle TTY tty is "/dev/ttyS1" Serielles Terminal disable start/stop characters and flowcontrol # ifconfig adsl Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:2000 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ath0 Link encap:Ethernet HWaddr 34:31:C4:56:C9:41 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:213 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) dsl Link encap:Point-to-Point Protocol inet addr:192.168.178.1 P-t-P:192.168.178.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth0 Link encap:Ethernet HWaddr 34:31:C4:56:C9:3F UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:60 overruns:0 frame:0 TX packets:245 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:86164 (84.1 KiB) guest Link encap:Ethernet HWaddr 34:31:C4:56:C9:3F inet addr:192.168.179.1 Bcast:192.168.179.255 Mask:255.255.255.0 UP BROADCAST ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lan Link encap:Ethernet HWaddr 34:31:C4:56:C9:3F inet addr:192.168.178.1 Bcast:192.168.178.255 Mask:255.255.255.0 inet6 addr: fe80::3631:c4ff:fe56:c93f/64 Scope:Link UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:60 errors:0 dropped:0 overruns:0 frame:0 TX packets:245 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:7992 (7.8 KiB) TX bytes:85120 (83.1 KiB) lan:0 Link encap:Ethernet HWaddr 34:31:C4:56:C9:3F inet addr:169.254.1.1 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:786 errors:0 dropped:0 overruns:0 frame:0 TX packets:786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:347944 (339.7 KiB) TX bytes:347944 (339.7 KiB) wifi0 Link encap:UNSPEC HWaddr 34-31-C4-56-C9-41-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2704 errors:0 dropped:0 overruns:0 frame:0 TX packets:692 errors:2 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:24 Memory:b8000000-b8010000 # iwconfig lo no wireless extensions. tunl0 no wireless extensions. Warning: Driver for device eth0 has been compiled with an ancient version of Wireless Extension, while this program support version 11 and later. Some things may be broken... eth0 ESSID:off/any Nickname:"" NWID:off/any Mode:Unknown/bug Channel:0 Access Point: 00:01:00:00:00:00 Bit Rate:8.38861 Mb/s Sensitivity:2146438480/0 RTS thr:off Fragment thr:off Encryption key:<too big> Power Management:on adsl no wireless extensions. lan no wireless extensions. guest no wireless extensions. dsl no wireless extensions. wifi0 no wireless extensions. ath0 IEEE 802.11ng ESSID:"FRITZ!Box 7312" Mode:Master Frequency:2.412 GHz Access Point: 34:31:C4:56:C9:41 Bit Rate:300 Mb/s Tx-Power:19 dBm RTS thr:off Fragment thr:off Encryption key:203D-3334-DA21-24DC-A1DD-1B23-8298-6A9E [2] Security mode:open Power Management:off Link Quality=94/94 Signal level=-96 dBm Noise level=-95 dBm Rx invalid nwid:10 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 printenv CONFIG_WLAN=y CONFIG_WLAN_RADIOSENSOR=y CONFIG_FON_HD=y CONFIG_USB_STORAGE_USERS=n CONFIG_TIMERCONTROL=y CONFIG_BETA_RELEASE=0 CONFIG_EWETEL_SMARTMETER=n CONFIG_USB_HOST_AVM=n CONFIG_LFS=y CONFIG_PERL=n CONFIG_FON_IPPHONE=y CONFIG_LTE=n CONFIG_I2C=n CONFIG_VPN_CERTSRV=n CONFIG_UTF8_FULL=y CONFIG_AB_COUNT=1 CONFIG_WLAN_TXPOWER=y CONFIG_CAPI_NT=n CONFIG_ONLINEHELP_URL=http://help.avm.de/fritzbox.php?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_NFS_CLI=n CONFIG_UDEV=y CONFIG_WLAN_OPENWIFI=n CONFIG_ATA_NOPASSTHROUGH=n CONFIG_JFFS2=y CONFIG_T38=y USER=root CONFIG_STOREUSRCFG=y CONFIG_NFS=n CONFIG_USB_TETHERING=n CONFIG_KIDS_CONTENT=n CONFIG_LED_EVENTS=y CONFIG_CODECS_IN_PCMROUTER=y CONFIG_CAPI_XILINX=y CONFIG_UBIK2=n CONFIG_SQLITE=n CONFIG_NEUERUL=y CONFIG_WLAN_ATH_NM_MAGPIE=n CONFIG_WEBGUI_PASS=n CONFIG_CHRONY=y CONFIG_FONGUI2=y CONFIG_CONFIGD=y CONFIG_DSL_UR8=n CONFIG_WLAN_WDS_NO_SLAVE=n CONFIG_TAM_ONRAM=n CONFIG_FONQUALITY=y CONFIG_SQLITE_VIDEO=n CONFIG_FTP=n CONFIG_USB=n CONFIG_GPS=n HOME=/ GCOV_PREFIX=/var/gcov OEM=1und1 CONFIG_MULTI_COUNTRY=n CONFIG_VDSL=n CONFIG_NCURSES=n CONFIG_PRODUKT_NAME=FRITZ!Box 7312 (UI) CONFIG_ENVIRONMENT_PATH=/proc/sys/urlader CONFIG_DECT_AUDIOD=y CONFIG_DECT_NO_EMISSION=y CONFIG_C4=n CONFIG_USB_HOST_TI=n ethaddr=34:31:C4:56:C9:3F CONFIG_AVMIPC_REMOTE_IP= CONFIG_PROV_DEFAULT=n CONFIG_ASSIST=y CONFIG_SWAP=y CONFIG_HOME_AUTO=n CONFIG_LED_NO_DSL_LED=y CONFIG_NTFS=n CONFIG_MANUAL_URL=https://assets.avm.de/manual/?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_SUBVERSION= CONFIG_VERSION=06.54 CONFIG_DIAGNOSE_LEVEL=0 CONFIG_USB_STORAGE=n CONFIG_USB_INTERNAL_HUB=n CONFIG_CAPI_POTS=n HWRevision_ATA=1 CONFIG_SAMBA=n CONFIG_WEBSRV=y CONFIG_USB_XHCI=n CONFIG_RELEASE=1 CONFIG_BLUETOOTH_CTP=n CONFIG_DECT_MONI_EX=y Language_is_default=yes CONFIG_ROMSIZE=16 CONFIG_FIRMWARE_URL=http://www.avm.de/fritzbox-firmware-update.php?hardware=189&oem=1und1&language=de&country=049 CONFIG_SERVICEPORTAL_URL=http://www.avm.de/fritzbox-service-portal.php?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_FLASH_DOUBLE=n CONFIG_PRODUKT=Fritz_Box_HW189 CONFIG_DECT_FW_ULE=n HWRevision=189 HWRevision_BitFileCount= ANNEX=B CONFIG_NO_EXTENDED_CODECS=y CONFIG_BUTTON=y CONFIG_ACCESSORY_URL=http://www.avm.de/fritzbox_apps.php?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_VERSION_MAJOR=117 CONFIG_MAILD=y CONFIG_XILINX=y CONFIG_TR064=y CONFIG_MEDIASRV_MOUNT=n CONFIG_CXX=n CONFIG_WLAN_ATH_NM_COMBO=n CONFIG_BOXLOWRESSOURCES=y CONFIG_DOCSIS_PCD_NO_REBOOT=n CONFIG_ONLINEHELP=y CONFIG_NQOS=y Country_is_default=yes CONFIG_VPN=y CONFIG_USB_PRINT_SERV=n CONFIG_GDB=n CONFIG_UPNP=y CONFIG_ETH_COUNT=1 CONFIG_USB_LTE=n CONFIG_WEBDAV=n CONFIG_CAPI=y TERM=vt102 CONFIG_MAILER=n CONFIG_TR069=y CONFIG_DSL_2DP=n CONFIG_WLAN_GUEST=y CONFIG_CDROM_FALLBACK=n CONFIG_PLUGINV2=n CONFIG_ONLINEPB=y CONFIG_USB_GSM=n CONFIG_FAXSEND=y CONFIG_WLAN_WEATHER_CAC=n CONFIG_PLC_DETECTION=y nor_size=16MB CONFIG_FHEM=n CONFIG_USB_GSM_VOICE=n CONFIG_WLAN_WDS=n CONFIG_DECT=y PATH=/sbin:/usr/sbin:/bin:/usr/bin CONFIG_WLAN_1130TNET=n CONFIG_CAPI_UBIK=n CONFIG_TELEKOM_KOFFER=n CONFIG_RAMDISK=n CONFIG_NAND=n CONFIG_MTD_MAILSEND=y CONFIG_INSTALL_TYPE=mips34_16MB_dect441_1eth_1ab_wlan11n_40508 CONFIG_DECT_PICTURED=y CONFIG_FAXSUPPORT=y enable_ata=1 CONFIG_WLAN_MADWIFI=y CONFIG_HOME_AUTO_NET=n CONFIG_MULTI_LANGUAGE=n CONFIG_QOS_METER=y CONFIG_WLAN_ATH_NM_PCI=y CONFIG_DECT_HOME=n CONFIG_SRTP=n CONFIG_IGD=y CONFIG_CONFIGSPACE_ONNAND=n CONFIG_UNIQUE_PASSWD=n CONFIG_WLAN_WMM=y CONFIG_DECT_ONOFF=n CONFIG_OEM_DEFAULT=avm CONFIG_EXT2=n CONFIG_PLUGINV2_WEBCM_INTERPRETER=n CONFIG_FAX2MAIL=y CONFIG_MEDIASRV=n CONFIG_MYFRITZ=y CONFIG_ATA=y CONFIG_HOMEI2C=n CONFIG_ERR_FEEDBACK=y CONFIG_EXT3=n CONFIG_BOX_FEEDBACK=y CONFIG_AUDIO=n CONFIG_BASIS=y CONFIG_SQLITE_BILDER=n CONFIG_VLYNQ=n CONFIG_DSL_MULTI_ANNEX=n CONFIG_IPV6=y CONFIG_WLAN_1350TNET=n CONFIG_VOIP_ENUM=n CONFIG_ECO=y CONFIG_INETD=y CONFIG_USB_HOST_INTERNAL=n CONFIG_LOGD=n SHELL=/bin/sh CONFIG_WLAN_IPTV=y CONFIG_USB_WLAN_AUTH=n CONFIG_CDROM=n CONFIG_NOTELNETD=n CONFIG_VOL_COUNTER=y CONFIG_WLAN_EACS=y CONFIG_REMOTE_HTTPS=y CONFIG_GDB_FULL=n CONFIG_HOSTNAME=fritz.box CONFIG_UTF8=y CONFIG_MEDIACLI=y CONFIG_USB_STORAGE_SPINDOWN=n CONFIG_LIB_MATH=y CONFIG_ECO_SYSSTAT=y CONFIG_DOCSIS_CLI=n CONFIG_AUTOUPDATE=n CONFIG_USB_HOST=n CONFIG_DOCSIS=n CONFIG_AURA=n CONFIG_MAILER2=y CONFIG_DECT_14488=y ETC_CONFIG_PATH=/etc/init.d/rc.init CONFIG_WLAN_TCOM_PRIO=n CONFIG_PLUGINV2_WLAN=n Language=de CONFIG_UPDATEFEATURE_URL=https://www.avm.de/fritzbox_firmware-features.php?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_DECT2=y CONFIG_WLAN_WDS2=n CONFIG_WEBCM_INTERPRETER=y CONFIG_SESSIONID=y CONFIG_KIDS=y CONFIG_MTD_RSS=y CONFIG_CAPI_TE=n CONFIG_WLAN_HOTSPOT=n CONFIG_NEWSLETTER_URL=http://www.avm.de/newsletter?hardware=189&oem=1und1&language=de&country=049&version=117.06.54&subversion= CONFIG_LABOR_DSL=n CONFIG_WLAN_WPS=y CONFIG_DECT_MONI=y CONFIG_ANNEX=B CONFIG_WEBUSB=n CONFIG_SOCAT=n PWD=/ CONFIG_DSL_VENDORID= CONFIG_MINI=n CONFIG_PLC=n CONFIG_LINEARTV=n Country=049 CONFIG_ETH_GBIT=n CONFIG_VLYNQ0=0 CONFIG_TAM_MODE=1 CONFIG_WLAN_GREEN=y GCOV_PREFIX_STRIP=5 TZ=CET-1CEST-2,M3.5.0/02:00:00,M10.5.0/03:00:00 CONFIG_PPA=y CONFIG_WLAN_SAVEMEM=n CONFIG_GDB_SERVER=n CONFIG_VLYNQ1=0 CONFIG_MTD_MAIL=y CONFIG_CAPI_MIPS=n CONFIG_FONBOOK2=y OEM_DEFAULT_INDEX= CONFIG_NAS=n CONFIG_WLAN_ATH_NM_USB=n CONFIG_WLAN_ATH_NM_OFFLOAD=n CONFIG_NFS_SRV=n CONFIG_MORPHSTICK=n CONFIG_BLUETOOTH=n CONFIG_ATA_FULL=n CONFIG_LUA=y CONFIG_TAM=y CONFIG_SPEECH_FEEDBACK=y CONFIG_LLTD=n CONFIG_SDK=n CONFIG_RAMSIZE=64 CONFIG_FON=y CONFIG_LIBZ=y CONFIG_DECT_CATIQ20=n CONFIG_DSL=y CONFIG_IPTV_4THOME=y HWSubRevision=1


(OEM) EVA Revision: 1.1322 Version: 2322

FritzOS 06.03 ref 117

ROM VER: 1.1.3 CFG 01 (AVM) EVA Revision: 1.1322 Version: 2322 (C) Copyright 2005 AVM Date: Dec 16 2011 Time: 14:45:22 (1) 2 0x0-0x341D [FLASH:] MACRONIX Uniform-Flash 16MB 64 Bytes WriteBuffer [FLASH:](Eraseregion [0] 128 sectors a 128kB) [SYSTEM:] AR9 on 393MHz/393MHz/196MHz Atheros 8030 detected Eva_AVM >........................... Lantiq xDSL CPE AR9 [ifx_enhance_phy_clock] PLL0_CFG: 0x00b0660b [ifx_enhance_phy_clock] PLL0 already modified. [ 0.000000] Linux version 2.6.32.60 (hjortmann@EmbeddedVM) (gcc version 4.6.3 (Buildroot 2011.11) ) #3 Thu Dec 5 14:42:47 CET 2013 [ 0.000000] phym = 04000000, mem = 04000000, max_pfn = 00004000 [ 0.000000] Reserving memory for CP1 @0xa4000000, size 0x00000000 [ 0.000000] wlan_mem_start = 0x03f9e000 [ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 804d2000) [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0001954c (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00003f9e [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00003f9e [ 0.000000] [c55] c55_mem_start = 0xfc0000 [ 0.000000] [module-alloc-by-name] 'modulemem' not in use, use AVM Kernel Config (6402048 bytes, reserved for module mem) [ 0.000000] [module-alloc] use 0x61b000 bytes at 0x81081000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16158 [ 0.000000] Kernel command line: console=ttyS1,115200n8r nor_size=16MB ethaddr=9C:C7:A6:A5:96:1E [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] [avm_cache_set_coherency]: setting cache coherency for HWRevision=189 to write through [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=0002c000 [ 0.000000] Readback ErrCtl register=0002c000 [ 0.000000] Memory: 52520k/65144k available (3412k kernel code, 12552k reserved, 1519k data, 176k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:181 [ 0.000000] [mips_cpu_irq_init] irq_base 0 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.000000] console [ttyS1] enabled, bootconsole disabled [ 0.020000] Calibrating delay loop... 261.32 BogoMIPS (lpj=1306624) [ 0.230000] Security Framework initialized [ 0.230000] Mount-cache hash table entries: 512 [ 0.230000] kernel_init: started [ 0.240000] kernel_init: kernel locked [power_managment_setup] reset 'DSL, DFE, AFE, VOICE, DSLTC, ARC' [power_managment_setup] reset 'LDO' [power_managment_setup] power down 'PPE TC, PPE EMA, LEDC, DFEV1, DFEV0' [power_managment_setup] power down 'MSI1, PDI1 PCIE1 PCIE1_PHY' [power_managment_setup] disable power domain 'DSL + DFE' [ 0.270000] NET: Registered protocol family 16 [ 0.280000] Reboot Status: (c) AVM 2013, Reboot Status is: Software-Reboot(c) AVM 2013, Reboot Status is: Software-Reboot(c) AVM 2013, Reboot Status is: Software-Reboot [ 0.290000] Reboot Status is: Soft-Reboot [ 0.290000] [avmnet] [avmnet_cfg_init] Driver version: 6.106.1.2 - Revision 1496:2498 - Do 5.12.2013 14:42:21 [ 0.300000] Lantiq PCI host controller driver, version 1.2.0, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.310000] bio: create slab <bio-0> at 0 [ 0.310000] pci 0000:00:00.0: PME# supported from D1 D2 [ 0.320000] pci 0000:00:00.0: PME# disabled [ 0.320000] NET: Registered protocol family 8 [ 0.320000] NET: Registered protocol family 20 [ 0.330000] NET: Registered protocol family 2 [ 0.330000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.340000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.340000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.350000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.360000] TCP reno registered [ 0.360000] NET: Registered protocol family 1 [ 0.360000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17 [ 0.360000] ,(c)2009 Infineon Technologies AG [ 0.360000] skb_shared_size:344 [ 0.380000] I[avm_register_busmaster:125]: Registered busmaster device: AVM_DMA_BUSMASTER [ 0.380000] [bcu_control_interrupt] 'FPI Slave BCU0' Error Interrupt [ 0.380000] Slave BCU[sBCU_EADD]: Error Address Register: 0x17000004 [ 0.380000] Slave BCU[sBCU_EDAT]: Error Data Capture Register: 0x0290030f [ 0.380000] Slave BCU[sBCU_CON] : Control Register: 0x4009ffff [ 0.380000] Slave BCU[sBCU_ECON]: Error Register (0x21be0030): [ 0.380000] FPI Bus Operation Code 0x2 [ 0.380000] FPI Bus Tag Number 0x1 [ 0.380000] FPI Bus Read Signal: passive [ 0.380000] FPI Bus Write Signal: active [ 0.380000] FPI Bus Supervisor Mode: active [ 0.380000] FPI Bus Acknowladge Signal: 0x3 [ 0.380000] FPI Bus Abort: passive [ 0.380000] FPI Bus Ready: active [ 0.380000] FPI Bus Timeout: not pressed [ 0.380000] FPI Bus Error Counter: 48 [ 0.450000] [bcu_control_init] interrupts for BCU installed [ 0.460000] Lantiq CGU driver, version 1.1.32, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.470000] clk-timing: timing:16, ram_refresh_timing:1524, base_ram_refresh_timing:7775 [ 0.480000] smvp_tc_init: tc 0 tcbind 00020000 tcstatus 18102000 [ 0.480000] smvp_tc_init: tc 1 tcbind 00200001 tcstatus 00000400 [ 0.480000] smvp_tc_init: tc 2 tcbind 00400001 tcstatus 00000400 [ 0.480000] smvp_tc_init: tc 3 tcbind 00600001 tcstatus 00000400 [ 0.480000] config3 0x424 MT 1 [ 0.480000] MVPControl 0x2, STLB 0 VPC 1 EVP 0 [ 0.480000] mvpconf0 0xb8008403, PVPE 1 PTC 3 M 1 [ 0.510000] initcall 0x804d98fc returned with disabled interrupts [ 0.520000] audit: initializing netlink socket (disabled) [ 0.520000] type=2000 audit(0.000:1): initialized [ 0.530000] [simple_profiling] 0 entries 50 min [ 0.530000] squashfs: version 3.4 (2008/08/26) Phillip Lougher [ 0.540000] JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.550000] fuse init (API version 7.13) [ 0.550000] msgmni has been set to 102 [ 0.560000] io scheduler noop registered (default) [ 0.560000] [avm_membench_init] [ 0.860000] avm_net_trace: Up and running. [ 0.860000] [loadcontrol] set auto - scale=1 [ 0.870000] [avm] configured: watchdog event debug [ 0.870000] [ 0.870000] AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: Dec 5 2013 14:42:03) [ 0.880000] [simple-profiling]: 4 performance counters implemented, OLD_34K [ 0.890000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 0.900000] Setup tcs=0x1 current_tc_mask=0x1, reg=0 [ 0.910000] [simple-profiling]: 4 performance counters implemented, OLD_34K [ 0.920000] Enable Performance Counter 1 for Data cache load/store misses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 0.930000] Setup tcs=0x1 current_tc_mask=0x1, reg=1 [ 0.930000] [avm]: AVM Simple Profiling enabled. [ 0.940000] ifx_pmu_init: Major 245 [ 0.940000] Lantiq PMU driver, version 1.2.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.950000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.960000] Infineon Technologies RCU driver version 1.0.7 [ 0.960000] ttyS0 at MMIO 0x1e100400 (irq = 100) is a PORT_IFX_ASC [ 0.970000] ttyS1 at MMIO 0x1e100c00 (irq = 107) is a PORT_IFX_ASC [ 0.980000] loop: module loaded [ 0.980000] nbd: registered device at major 43 [ 0.980000] [0]system-load 1 loadavg 0.0 0.0 0.0 - 13 tasks:0 % curr:swapper(0 %) max:swapper(0 %, pid:1), readytorun: 1, pgfault 0/s (max 0 avg 0.0) [ 1.020000] Generic platform RAM MTD, (c) 2004 Simtec Electronics [ 1.020000] Platform NOR MTD, (c) AVM 2010 [ 1.020000] [plat_nor_probe]start probe [ 1.030000] [do_map_probe] driver_name=cfi_probe [ 1.030000] mtd-nor: Found 1 x16 devices at 0x0 in 16-bit bank [ 1.040000] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.040000] mtd-nor: CFI does not contain boot bank location. Assuming top. [ 1.050000] number of CFI chips: 1 [ 1.050000] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. [ 1.060000] [ifx_jffs2_parser_function] mtd_info->name mtd-nor mtd_info->index 0 param=0 p_mtd_pat=0x83a1a954 [ 1.070000] [ifx_jffs2_parser_function] try partition kernel (offset 0x20000 len 16121856) [ 1.080000] [ifx_jffs2_parser_function] magic 19852003 found @pos 0xd80000, size 2097152 [ 1.090000] [ifx_squashfs_parser_function] mtd_info->name mtd-nor mtd_info->index 0 param=0 p_mtd_pat=0x83a1a954 [ 1.120000] [ifx_squashfs_parser_function:320] pos: 0x17a900 | offs[0]: 0x17a900 | size[0]: 14702336 | offs[1]: 0x20000 | size[1]: 1419520 [ 1.130000] [ifx_squashfs_parser_function] magic found @pos 0x17a900 [ 1.130000] 6 find_squashfs partitions found on MTD device mtd-nor [ 1.140000] Creating 6 MTD partitions on "mtd-nor": [ 1.140000] 0x00000017a900-0x000000f80000 : "rootfs" [ 1.150000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.160000] {ifx_mtd_add_notifier} name rootfs [ 1.170000] 0x000000020000-0x00000017a900 : "kernel" [ 1.170000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 1.180000] {ifx_mtd_add_notifier} name kernel [ 1.190000] 0x000000000000-0x000000020000 : "urlader" [ 1.190000] {ifx_mtd_add_notifier} name urlader [ 1.200000] 0x000000f80000-0x000000fc0000 : "tffs (1)" [ 1.200000] {ifx_mtd_add_notifier} name tffs (1) [ 1.210000] 0x000000fc0000-0x000001000000 : "tffs (2)" [ 1.210000] {ifx_mtd_add_notifier} name tffs (2) [ 1.220000] 0x000000d80000-0x000000f80000 : "jffs2" [ 1.220000] {ifx_mtd_add_notifier} name jffs2 [ 1.230000] {ifx_mtd_add_notifier} name mtd-nor [ 1.230000] mtd-nor mtd-nor: registered mtd device [ 1.240000] Lantiq SSC driver, version 2.4.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.240000] Unknown SPI device: 0xFF 0xFF 0xFF [ 1.250000] ifx_spi_flash_init: Found no serial flash device [ 1.250000] tun: Universal TUN/TAP device driver, 1.6 [ 1.260000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.270000] IFX SWITCH API, Version 1.1.8.5 [ 1.270000] SWAPI: Registered character device [switch_api] with major no [81] [ 1.380000] mice: PS/2 mouse device common for all mice [ 1.380000] i2c /dev entries driver [ 1.390000] CAPI Subsystem Rev 1.1.2.8 [ 1.390000] AVM PA 4.1.3 2013-11-18 [ 1.390000] AVM PA skb pktinfo at offset 128 size 192 [ 1.400000] [loadcontrol]module avm_pa registered [ 1.400000] IPv4 over IPv4 tunneling driver [ 1.410000] TCP cubic registered [ 1.410000] mcfw: IGMPv3 fast forwarding [ 1.410000] NET: Registered protocol family 10 [ 1.420000] IPv6 over IPv4 tunneling driver [ 1.420000] NET: Registered protocol family 17 [ 1.430000] NET: Registered protocol family 8 [ 1.430000] atmpvc_init() failed with -17 [ 1.430000] KOAM is loaded successfully. [ 1.440000] l2tp_core: L2TP core driver, V2.0 [ 1.440000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.450000] l2tp_netlink: L2TP netlink interface [ 1.450000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.460000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.470000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0) [ 1.470000] mount on mtd3 and mtd4 (double buffering) [ 1.480000] Adam2 environment variables API installed. [ 1.480000] {avmnet_cfg_netinit} [ 1.490000] [avmnet] No config found for HWRev 189, HWSubRev 1, Profile-ID 0, trying base config for HWSubRev [ 1.500000] [avmnet] No config found for HWRev 189, HWSubRev 1, trying base config for HWRev [ 1.510000] {avmnet_mac_ar9_init} Init on module mac_ar9_0 called. [ 1.520000] [avmnet] [avmnet_mac_ar9_setup] IFX_AR9_ETH_CTL(0): 0x424001 [ 1.530000] [avmnet] [avmnet_mac_ar9_setup] mac_nr: 0, vlan_reg: 0x4070001 [ 1.660000] [avm_pa_multiplexer_init] start [ 1.660000] [avm_pa_multiplexer_init] init complete [ 1.660000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 9c:c7:a6:a5:96:1e [ 1.670000] kernel_init: basic setup done [ 1.680000] [squashfs] use lzma compression [ 1.690000] VFS: Mounted root (squashfs filesystem) readonly on device 31:0. [ 1.690000] Freeing unused kernel memory: 176k freed [ 1.740000] trying /sbin/init starting pid 112, tty '/dev/ttyS1': '/etc/init.d/rc.S' tar: removing leading '/' from member names source files in group 0 ... /etc/init.d/S00-signal /etc/init.d/S05-watchdog /etc/init.d/S09-rtc /etc/init.d/S01-head /etc/init.d/S08-tffs /etc/init.d/S02-led /etc/init.d/S09-config [ 2.740000] TFFS Name Table K [ 4.250000] [module-alloc-by-name] give 0x11000 bytes at 0x81081000 to module 'led_modul_Fritz_Box_HW189' (0x60a000 bytes left) [ 4.260000] led_modul_Fritz_Box_HW189: module license ' [ 4.260000] (C) Copyright 2012 by AVM [ 4.260000] ' taints kernel. [ 4.270000] Disabling lock debugging due to kernel taint [ 4.290000] [led_gpio_out_bit] Error: Setting GPIO pin 45 to 1 failed! [ 4.300000] AVM_WATCHDOG: System Init UEberwachung 240 Sekunden mknod: /var/flash/ar7.cfg: File exists P-Defaults: do nothing [ 4.850000] [module-alloc-by-name] give 0x1000 bytes at 0x81092000 to module 'rtc_avm' (0x609000 bytes left) [ 4.870000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0 [ 4.880000] [avm-rtc]: avm_rtc_probe: register: ret=0x83063400 [ 4.880000] [avm-rtc]: avm_rtc_probe: success exceute files in group 0 ... /etc/init.d/E05-basemodules group 0 done ... source files in group 1 ... /etc/init.d/S10-html /etc/init.d/S12-default /etc/init.d/S10-vm /etc/init.d/S15-filesys /etc/init.d/S11-config_def /etc/init.d/S17-capi /etc/init.d/S11-piglet /etc/init.d/S17-tam [ 5.110000] [ 5.110000] [avm_debug]redirect kernel-messages (/dev/debug) [ 5.170000] [module-alloc-by-name] give 0x8000 bytes at 0x81093000 to module 'Piglet_noemif' (0x601000 bytes left) [ 5.170000] [module-alloc-by-name] 0x8000 bytes used, 0xAB30 bytes expected [ 5.180000] [piglet]use default-settings (1 gpio from hw_config) [ 5.320000] patch_dectfw: C025D000, totallen = 42434(A5C2) [ 5.320000] patch_dectfw: patch_adress: A0 max_len: 26 with Version 2 Len: 17 [ 5.320000] patch_dectfw: dectmode 1 [ 5.320000] dect_loader: slow-bootmode <FE>* ********************************************************************************** [ 8.510000] dect144xx_file_process: upload of '/lib/modules/dectfw_secondlevel_441.hex' successfull [ 10.520000] [piglet]TDM: FS: 8005 Hz CLK: 1024005 Hz checkempty: : No such file or directory [jffs2] Mount /data success (mtd5 size 2097152) [jffs2] write env variable jffs2_size to 32 [ 11.010000] [module-alloc-by-name] give 0x5D000 bytes at 0x8109B000 to module 'pcmlink' (0x5A4000 bytes left) [ 11.010000] [module-alloc-by-name] 0x5D000 bytes used, 0x65E18 bytes expected [pcmlink]svn: 1922 [ 11.120000] [pcmlink]VPE-Interface: base 0xFC0000, maxsize 131072, host-irq 142 [ 11.510000] [0]system-load 6 loadavg 0.15 0.3 0.1 - 23 tasks:30 % curr:modprobe(4 %) max:init(10 %, pid:1), readytorun: 1, pgfault 1927/s (max 1 avg 1.0) [ 11.640000] [module-alloc-by-name] give 0xB2000 bytes at 0x810F8000 to module 'isdn_fbox_fon5' (0x4F2000 bytes left) [ 11.640000] [module-alloc-by-name] 0xB2000 bytes used, 0xC7608 bytes expected [ 11.730000] [isdn]svn:3066 [ 11.730000] driver params overwritten io_addr=0x0 irq_num=0 [ 11.730000] [pcmlink]chrony-support [ 11.740000] VPE loader: loading segment 1 to 80FC0000 (14000 bytes) elf loaded [ 11.740000] vpe_run: tc 1 start-addr 80FC0000 [ 11.740000] vpe_run: tc 1 tcstatus 18002000 tcbind 00200001 MVPCONTROL 00000002 vpeopt 00000000 [ 12.750000] PCMLINK: Version 7.498 Codecslots=6 Slics=1 Pots=1 TE=0 NT=0 DECT=4 (IA3222) no HwCross DSP-EC: 2 [ 13.230000] [module-alloc-by-name] give 0x54000 bytes at 0x811AA000 to module 'capi_codec' (0x49E000 bytes left) [ 13.230000] [module-alloc-by-name] 0x54000 bytes used, 0x5DA80 bytes expected capicodec_init() [capi_codec] support fax [capi_codec] support Codecs [ 13.450000] [module-alloc-by-name] give 0x35000 bytes at 0x811FE000 to module 'avm_dect' (0x469000 bytes left) [ 13.450000] [module-alloc-by-name] 0x35000 bytes used, 0x3D3EC bytes expected [ 13.480000] [DECTDRV_ERR] avm_dect driver init [ 13.480000] [DECTDRV_ERR] [avm_dect]avm_dect_thread: start [ 13.490000] [module-alloc-by-name] give 0x3000 bytes at 0x81233000 to module 'dect_io' (0x466000 bytes left) [ 13.490000] [module-alloc-by-name] 0x3000 bytes used, 0x454C bytes expected TAM: create JFFS2 directory /data/tam [ 13.520000] dect_uicp_from_dect, ignore 8 bytes, dect_manager not up: 2F 7B exceute files in group 1 ... /etc/init.d/E15-device mknod led c 242 mknod tffs c 243 [ 13.610000] dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: F6 14 mknod avm_power c 252 mknod debug c 248 mknod avm_event c 249 mknod capi_oslib c 68 mknod dect_io c 227 / group 1 done ... source files in group 2 ... /etc/init.d/S21-udev exceute files in group 2 ... group 2 done ... source files in group 3 ... /etc/init.d/S30-ledcfg exceute files in group 3 ... group 3 done ... source files in group 4 ... /etc/init.d/S40-swap /etc/init.d/S44-hostname /etc/init.d/S48-configd /etc/init.d/S42-ptest /etc/init.d/S46-usb Jan 1 01:00:13 udevd[355]: specified group 'tty' unknown Jan 1 01:00:13 udevd[355]: specified group 'dialout' unknown Jan 1 01:00:13 udevd[355]: specified group 'kmem' unknown Jan 1 01:00:13 udevd[355]: specified group 'video' unknown Jan 1 01:00:13 udevd[355]: specified group 'audio' unknown Jan 1 01:00:13 udevd[355]: specified group 'lp' unknown Jan 1 01:00:13 udevd[355]: specified group 'disk' unknown Jan 1 01:00:13 udevd[355]: specified group 'floppy' unknown Jan 1 01:00:13 udevd[355]: specified group 'cdrom' unknown Jan 1 01:00:13 udevd[355]: specified group 'tape' unknown [ 14.020000] [module-alloc-by-name] give 0x1000 bytes at 0x81236000 to module 'lzo_compress' (0x465000 bytes left) [ 14.020000] [module-alloc-by-name] 0x1000 bytes used, 0x1888 bytes expected [ 14.050000] [module-alloc-by-name] give 0x1000 bytes at 0x81237000 to module 'lzo_decompress' (0x464000 bytes left) [ 14.050000] [module-alloc-by-name] 0x1000 bytes used, 0x1908 bytes expected [ 14.100000] [module-alloc-by-name] give 0x4000 bytes at 0x81238000 to module 'ramzswap' (0x460000 bytes left) [ 14.100000] [module-alloc-by-name] 0x4000 bytes used, 0x5F00 bytes expected [ 14.120000] ramzswap: /dev/ramzswap0 initialized: disksize_kb=8192mknod: /dev/ramzswap0: File exists [ 14.160000] Adding 8184k swap on /dev/ramzswap0. Priority:-1 extents:1 across:8184k SS exceute files in group 4 ... /etc/init.d/E40-dsl /etc/init.d/E46-net /etc/init.d/E47-voip [dsl get xtse] ANNEX=B [dsl get xtse] setting Annex B and J [dsl get xtse] 10 00 10 40 00 04 01 00 [dsl sus] starting ar9 dsp... [dsl sus] ANNEX=B DIAGNOSE=no [ 15.270000] [module-alloc-by-name] give 0x9000 bytes at 0x8123C000 to module 'ifxmips_mei' (0x457000 bytes left) [ 15.270000] [module-alloc-by-name] 0x9000 bytes used, 0xBCAC bytes expected [dsl mei] Lantiq MEI driver version: 5.03.00 [dsl mei] Lantiq MEI driver global debug_level: 0 [dsl sus] loaded ar9 mei driver: ifxmips_mei.ko with params: [ 15.530000] [module-alloc-by-name] give 0x4C000 bytes at 0x81245000 to module 'drv_dsl_cpe_api' (0x40B000 bytes left) [ 15.530000] [module-alloc-by-name] 0x4C000 bytes used, 0x559A0 bytes expected [dsl drv] Lantiq CPE API Driver version: DSL CPE API V4.9.2.1 [dsl drv] Predefined debug level: 4 [dsl drv] dynamically registered major number 239 for drv_dsl_cpe_api [dsl sus] loaded ar9 dsl driver: drv_dsl_cpe_api.ko with params: [dsl sus] created ar9 dsl device node /dev/dsl_ar9 (major: 239 , minor: 0) [dsl sus] created ar9 mei device node /dev/ifx_mei (major: 105 , minor: 0) [dsl sus] started dsl_control (configuration: -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.sh ) nohup: appending output to nohup.out 0 [dsl sus] started dsl_monitor [dsl sus] ....ar9 dsp started [ 17.560000] [module-alloc-by-name] give 0x11E000 bytes at 0x81291000 to module 'kdsldmod' (0x2ED000 bytes left) [ 17.560000] [module-alloc-by-name] 0x11E000 bytes used, 0x14A6A4 bytes expected [ 17.670000] kdsldmod: init start (Feb 7 2014 15:25:04) sizeof(struct sk_buff)=440 [ 17.680000] userman: device registerd (userman_url) with major=233 <6>kdsld: ttychannel: ldisc 8 registered [ 17.680000] kdsldmod: init done [ 18.600000] dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: F6 14 Jan 1 01:00:18 l2tpv3d[571]: starting. Jan 1 01:00:18 l2tpv3d[571]: verbose: DISABLED [ 21.280000] ADDRCONF(NETDEV_UP): lan: link is not ready [ 21.290000] ADDRCONF(NETDEV_UP): guest: link is not ready [avm_power] eth: port 0 force normal CON t0 [avm_power] eth: port 1 force throttle CON t0 [ 21.940000] [avmnet] [avmnet_power_config] tried to set mode for port 1 [ 21.940000] [avm_power] : ethernet switch failed [avm_power] eth: port 2 force throttle CON t0 [ 21.940000] [avmnet] [avmnet_power_config] tried to set mode for port 2 [ 21.940000] [avm_power] : ethernet switch failed [avm_power] eth: port 3 force throttle CON t0 [ 21.940000] [avmnet] [avmnet_power_config] tried to set mode for port 3 [ 21.940000] [avm_power] : ethernet switch failed [ 22.110000] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 22.110000] device eth0 entered promiscuous mode Jan 1 01:00:21 multid[590]: DHCPD on lan:0 skipped, is virtual interface rc.wlan: Start WLAN... [ 22.710000] DSP: XDU=1( D1 ) OVR=0 MIPS_OVR=0 [ 22.810000] [0]system-load 9 loadavg 0.36 0.8 0.3 - 59 tasks:38 % curr:wland(0 %) max:mtdblockd(13 %, pid:86), readytorun: 2, pgfault 3655/s (max 2 avg 1.0) WLAND:[00609]:01:00.22:Build = Dec 5 2013 14:33:42 [ 23.590000] dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: F6 14 Jan 1 01:00:23 dsld[613]: startup ($Revision: 1.95 $$CompileDate: Feb 7 2014 15:23:27 $) Jan 1 01:00:23 dsld[613]: set_preconfig1 Jan 1 01:00:23 dsld[613]: sync_group in ar7.cfg: Jan 1 01:00:23 dsld[613]: sync_group:sync_dsl(enabled=1), nr=0 Jan 1 01:00:23 dsld[613]: vcc:1/32 Jan 1 01:00:23 dsld[613]: dsliface:internet Jan 1 01:00:23 dsld[613]: dsliface:voip Jan 1 01:00:23 dsld[613]: sync_group: dsl Jan 1 01:00:23 dsld[613]: sync_dsl is igd_device Jan 1 01:00:23 dsld[613]: set_preconfig2 Jan 1 01:00:23 dsld[613]: add_vcc_connection: dsl Jan 1 01:00:23 dsld[617]: DSL Mac 9c:c7:a6:a5:96:21 Jan 1 01:00:23 dsld[617]: VOIP Mac 9c:c7:a6:a5:96:22 Jan 1 01:00:23 dsld[617]: VCC2 Mac 9c:c7:a6:a5:96:23 Jan 1 01:00:23 dsld[617]: VCC3 Mac 9c:c7:a6:a5:96:1f <3>kdsld: kdsld_vcc_preunregister: * Jan 1 01:00:24 dsld[617]: voip: ppptarget voip disabled, ignored [ 25.000000] kdsld: nr_ipv4 0 nr_ipv6 0 nr_vpn 0 Jan 1 01:00:24 dsld[617]: sync_group(prepare_interfaces): dsl: inet_nr=0 Jan 1 01:00:24 dsld[617]: nach prepare_interfaces: dsld.dsliface_default_inet_nr=0, dsld.dsliface_voip_nr=-1 Jan 1 01:00:24 dsld[617]: get_queueindex: none: not found Jan 1 01:00:24 dsld[617]: get_queueindex: none: not found Jan 1 01:00:24 dsld[617]: queue 0: prio 0 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 1: prio 10 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 2: prio 20 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 3: prio 30 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 4: prio 100 weight 90 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 5: prio 100 weight 10 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: queue 6: prio 200 weight 0 shrate 0 shburst 0 wan Jan 1 01:00:24 dsld[617]: appl 0: sip-appl result 1 Jan 1 01:00:24 dsld[617]: classifer: local "localmark sip" result 1 Jan 1 01:00:24 dsld[617]: classifer: local "localmark rtp" result 1 Jan 1 01:00:24 dsld[617]: classifer: local "localmark sipdns,ntpdns,tr069dns,tr069" result 2 Jan 1 01:00:24 dsld[617]: classifer: local "localmark igmp" result 3 Jan 1 01:00:24 dsld[617]: classifer: local "localmark webdav" result 4 Jan 1 01:00:24 dsld[617]: classifer: lan "udp.dport 43962,47806" result 2 Jan 1 01:00:24 dsld[617]: classifer: lan "ip.proto IPv6-ICMP" result 2 Jan 1 01:00:24 dsld[617]: classifer: lan "ip.proto icmp" result 2 Jan 1 01:00:24 dsld[617]: classifer: lan "udp.dport 53" result 2 Jan 1 01:00:24 dsld[617]: classifer: lan "udp.dport 5060" result 5 Jan 1 01:00:24 dsld[617]: classifer: lan "dhcpoption 12 FRITZ!Media* mediatab" result 6 Jan 1 01:00:24 dsld[617]: classifer: lan "ethsrctab mediatab" result 6 Jan 1 01:00:24 dsld[617]: classifer: local "localmark sip_internet" result 1 Jan 1 01:00:24 dsld[617]: classifer: local "localmark rtp_internet" result 1 Jan 1 01:00:24 dsld[617]: result 0: tos 65535 vprio 65535 queue 5 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 1: tos 65535 vprio 65535 queue 2 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 2: tos 65535 vprio 65535 queue 1 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 3: tos 65535 vprio 65535 queue 0 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 4: tos 65535 vprio 65535 queue 6 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 5: tos 65535 vprio 65535 queue 2 appl 0 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: result 6: tos 65535 vprio 65535 queue 3 appl 65535 bridge 65535 forward 65535 Jan 1 01:00:24 dsld[617]: interface lo added. Jan 1 01:00:24 dsld[617]: interface lo up. Jan 1 01:00:24 dsld[617]: interface tunl0 added. Jan 1 01:00:24 dsld[617]: interface sit0 added. Jan 1 01:00:24 dsld[617]: interface eth0 added. Jan 1 01:00:24 dsld[617]: interface eth0 up. Jan 1 01:00:24 dsld[617]: interface adsl added. Jan 1 01:00:24 dsld[617]: interface lan added. Jan 1 01:00:24 dsld[617]: interface lan up. Jan 1 01:00:24 dsld[617]: interface guest added. Jan 1 01:00:24 dsld[617]: interface guest up. Jan 1 01:00:24 dsld[617]: interface hotspot added. Jan 1 01:00:24 dsld[617]: interface hotspot up. Jan 1 01:00:24 dsld[617]: start register_vccs_and_ifaces_on_kdsld for sync_dsl Jan 1 01:00:24 dsld[617]: setup_dslchannel: ifname= Jan 1 01:00:24 dsld[617]: kdsld_preregister_vcc: predsl1 <3>kdsld: kdsld_vcc_preregister: predsl1 <3>kdsld: kdsld_vcc_preregister: vcc->ifaces=(null) Jan 1 01:00:24 dsld[617]: kdsld_preregister_vcc: kdsld_vccidx=0 Jan 1 01:00:24 dsld[617]: verbose: DISABLED Jan 1 01:00:25 telefon[631]: use clock_gettime(CLOCK_MONOTONIC)! Jan 1 01:00:25 telefon[631]: No S0NT! Jan 1 01:00:25 telefon[631]: NoOldMSNNames telefon: SIGCHLD PID 632 received! Jan 1 01:00:25 telefon[631]: WARNING No config file '/var/flash/fx_def' ! Jan 1 01:00:25 ctlmgr[577]: WLANLIB: my_wlan_init:649: svn revision 1493 Jan 1 01:00:25 telefon[631]: INFO No MOH file '/var/flash/fx_moh' ! Jan 1 01:00:25 ctlmgr[577]: WLANLIB: weak_wlan_check:63: Missing weak 'process_wlanmail'. telefon: SIGCHLD PID 645 received! group 4 done ... source files in group 5 ... exceute files in group 5 ... group 5 done ... source files in group 6 ... exceute files in group 6 ... group 6 done ... source files in group 7 ... /etc/init.d/S73-capitcp /etc/init.d/S75-inetd /etc/init.d/S76-media [ 28.550000] dect_uicp_from_dect, ignore 16 bytes, dect_manager not up: F6 14 exceute files in group 7 ... group 7 done ... source files in group 8 ... /etc/init.d/S85-apps exceute files in group 8 ... group 8 done ... source files in group 9 ... /etc/init.d/S99-tail [ 29.170000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 255 -> 0 [ 29.170000] [DECTDRV_ERR] EepromReadExtRecord, record 0 not found (no records) [ 29.170000] [DECTDRV_ERR] EepromReadExtRecord, record 0 not found (no records) run_clock demon started [ 29.560000] SysRq : Changing Loglevel Loglevel set to 4 Jan 1 01:00:29 telefon[638]: NoOldMSNNames mknod: /var/flash/fx_def: File exists telefon: SIGCHLD PID 679 received! Jan 1 01:00:29 telefon[638]: WARNING No config file '/var/flash/fx_def' ! Info: have to stop cat /dev/debug. [ 5.170000] [module-alloc-by-name] give 0x8000 bytes at 0x81093000 to module 'Piglet_noemif' (0x601000 bytes left) [ telefon: SIGHUP received! pbd[629]: received signal Hangup pbd[628]: received signal Hangup pbd[627]: received signal Hangup pbd[625]: received signal Hangup Please press Enter to activate this console. telefon: SIGHUP received! Jan 1 01:00:29 telefon[638]: Stop DECT starting pid 683, tty '/dev/ttyS1': '-/bin/sh' BusyBox v1.19.3 (2012-08-08 12:53:46 CEST) built-in shell (ash) Enter 'help' for a list of built-in commands. ermittle die aktuelle TTY tty is "/dev/ttyS1" Serielles Terminal # rc.wlan: Start WLAN... rc.wlan: WLAN daemon already running uname -a Linux fritz.fonwlan.box 2.6.32.60 #3 Thu Dec 5 14:42:47 CET 2013 mips GNU/Linux telefon: SIGCHLD PID 694 received! telefon: SIGCHLD PID 648 received!


cat /proc/cpuinfo

system type		: AR9
processor		: 0
cpu model		: MIPS 34Kc V4.12
BogoMIPS		: 261.32
wait instruction	: yes
microsecond timers	: yes
tlb_entries		: 16
extra interrupt vector	: yes
hardware watchpoint	: yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb]
ASEs implemented	: mips16 dsp mt
shadow register sets	: 1
core			: 0
VCED exceptions		: not available
VCEI exceptions		: not available

lsmod

Module                  Size  Used by    Tainted: P  
userman_mod            51600  4 
ath_pktlog             15776  0 
umac                  637696  1 ath_pktlog
ath_dev               200240  2 ath_pktlog,umac
ath_dfs                46128  2 umac,ath_dev
ath_rate_atheros       25440  3 ath_pktlog,umac,ath_dev
ath_hal               582992  4 ath_pktlog,umac,ath_dev,ath_rate_atheros
asf                     7632  4 umac,ath_dev,ath_dfs,ath_hal
adf                    13184  3 umac,ath_dev,ath_hal
aae                   107888  4 umac,ath_dev,ath_dfs,ath_hal
kdsldmod             1168720  9 userman_mod
drv_dsl_cpe_api       309104  2 
ifxmips_mei            36544  3 drv_dsl_cpe_api
ramzswap               15424  1 
lzo_decompress          1888  1 ramzswap
lzo_compress            1728  1 ramzswap
dect_io                10256  0 
avm_dect              216400  1 dect_io
capi_codec            341840  0 
isdn_fbox_fon5        727920  5 
pcmlink               378736  4 avm_dect,capi_codec,isdn_fbox_fon5
Piglet_noemif          30496  0 
rtc_avm                 3584  1 pcmlink
led_modul_Fritz_Box_HW189    68576  4 

processes

PID USER VSZ STAT COMMAND 1 root 1236 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [events/0] 5 root 0 SW [khelper] 8 root 0 SW [async/mgr] 22 root 0 SW [sync_supers] 23 root 0 SW [bdi-default] 25 root 0 SW [kblockd/0] 43 root 0 SW [kswapd0] 44 root 0 SW [aio/0] 53 root 0 SW [pm_info] 60 root 0 SWN [avmdebug] 86 root 0 SW [mtdblockd] 104 root 0 SW [l2tp] 108 root 0 SW [tffsd_mtd_0] 109 root 0 SW [avmnet_workqueu] 111 root 0 SW [avmnet_timer] 171 root 0 SW [cleanup_timer_f] 275 root 0 SWN [jffs2_gcd_mtd5] 280 root 0 SW [capi_pipew/0] 281 root 0 SW [capi_schedw/0] 282 root 0 SW [pcmlink_ctrl] 283 root 0 SW [capitransp] 286 root 0 SW< [avm_dect_thread] 287 root 0 SW [ksock tcp worke] 288 root 0 SW [ksock tcp serve] 373 root 1236 S < /sbin/udevd --daemon 374 root 1236 S < /sbin/udevd --daemon 375 root 1236 S < /sbin/udevd --daemon 389 root 2480 S /bin/configd 414 root 0 SW [RTT_Client] 422 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 430 root 2492 S dsl_monitor -d 431 root 2492 S dsl_monitor -d 432 root 2492 S dsl_monitor -d 434 root 2492 S dsl_monitor -d 440 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 441 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 442 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 443 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 444 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 445 root 3152 S dsl_control -i10_00_10_40_00_04_01_00 -f/lib/modules/dsp_ar9/ar9-B-dsl.bin -n/etc/dsl/notify/dsl_notify.s 563 root 0 SWN [dectuart_route] 567 root 2692 S avmipcd 571 root 3208 S l2tpv3d 577 root 12472 S ctlmgr 581 root 5108 S upnpd 584 root 0 SW [autbtex] 585 root 0 SW [ceocex_ne] 586 root 0 SW [pmex_ne] 587 root 0 SW [pmex_fe] 590 root 3948 S multid 602 root 2776 S upnpdevd 612 root 2588 S wland -B 617 root 4276 S dsld -i -n 625 root 4288 S pbd 626 root 4288 S pbd 628 root 4288 S pbd 629 root 4288 S pbd 635 root 12472 S ctlmgr 636 root 12472 S ctlmgr 637 root 12472 S ctlmgr 638 root 5724 S telefon a127.0.0.1 643 root 5724 S telefon a127.0.0.1 644 root 5724 S telefon a127.0.0.1 655 root 5796 S < voipd 664 root 1236 S /usr/sbin/inetd 671 root 1136 S /bin/run_clock -c /dev/tffs -d 683 root 1256 S -/bin/sh 1241 root 5108 S upnpd 1242 root 5108 S upnpd 1243 root 5108 S upnpd 1244 root 1412 S hostapd -B /etc/wpa2/WSC_ath0.conf 1262 root 3416 S usermand 1264 root 3268 S contfiltd 1312 root 1232 R ps w 1313 root 1232 R ps


mount

rootfs on / type rootfs (rw)
/dev/root on / type squashfs (ro,relatime)
proc on /proc type proc (rw,relatime)
tmpfs on /var type tmpfs (rw,relatime)
tmpfs on /dev type tmpfs (rw,relatime)
sysfs on /sys type sysfs (rw,relatime)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
/dev/mtdblock5 on /data type jffs2 (rw,relatime)

disk free

ilesystem                Size      Used Available Use% Mounted on
/dev/root                10.2M     10.2M         0 100% /
tmpfs                    25.8M    600.0K     25.2M   2% /var
tmpfs                    25.8M     12.0K     25.8M   0% /dev
/dev/mtdblock5            2.0M    388.0K      1.6M  19% /data

ifconfig

adsl Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:2000 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ath0 Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:20 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:13 errors:0 dropped:224 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:5447 (5.3 KiB) eth0 Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:1E UP BROADCAST PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) guest Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:1E inet addr:192.168.179.1 Bcast:192.168.179.255 Mask:255.255.255.0 inet6 addr: fe80::9ec7:a6ff:fea5:961e/64 Scope:Link UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:368 (368.0 B) hotspot Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:1E UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lan Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:1E inet addr:192.168.178.1 Bcast:192.168.178.255 Mask:255.255.255.0 inet6 addr: fe80::9ec7:a6ff:fea5:961e/64 Scope:Link UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:259 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:79305 (77.4 KiB) lan:0 Link encap:Ethernet HWaddr 9C:C7:A6:A5:96:1E inet addr:169.254.1.1 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:810 errors:0 dropped:0 overruns:0 frame:0 TX packets:810 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:311942 (304.6 KiB) TX bytes:311942 (304.6 KiB) wifi0 Link encap:UNSPEC HWaddr 9C-C7-A6-A5-96-20-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1012 errors:0 dropped:0 overruns:0 frame:0 TX packets:6241 errors:10 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:24 Memory:b8000000-b8010000


toh/avm/fritz.box.wlan.7312.txt · Last modified: 2017/08/22 12:47 by everloop