User Tools

Site Tools


toh:avm:fritz.box.wlan.7360

AVM FRITZ!Box Fon WLAN 7360 (SL)

This box is using a Lantiq SoC, see soc.lantiq The box is currently supported as "stable" in LEDE since 17.01 (reboot)

The DECT does not work and is not supported due to missing PIGLET and DECT Driver (AVM driver is closed source) If you need DECT and/ or fully phone support, you should take a look at freetz.

Phone works only via SIP with asterisk or another SIP package and a wifi or ethernet SIP phone.

Supported Versions

Version/Model Launch Date S/N OpenWrt/LEDE Version Supported Model Specific Notes
v1 2010 D303.400.30.xxx.xxx L: 17.01, O: WIP 1&1 (1und1)

Hardware Highlights

CPU Ram Flash Network USB Serial JTag DSL
2x MIPS 34Kc 5.6 128MiB 16MB 2x 1000M (eth0, eth1) & 2x 100M (eth2, eth3) Yes (2x 2.0) Yes ? VDSL2 + ADSL2+

Hardware

Flashing via BOOTLOADER

  • You can only Flash the squashfs image via ADAM2, you should drive a session like in the code box:
  • While flashing, the Fritzbox will indicate the flash progress via the info LED (red light) and turns off when done.

lipkegu@Medice-PC /opt/openwrt-trunk $ ftp 192.168.178.1
Connected to 192.168.178.1.
220 ADAM2 FTP Server ready
Name (192.168.178.1:lipkegu): adam2
331 Password required for adam2
Password: 
230 User adam2 successfully logged in
Remote system type is AVM.
ftp> passive
Passive mode on.
ftp> binary
200 Type set to BINARY
ftp> debug 1
Debugging on (debug=1).
ftp> quote MEDIA FLSH
---> MEDIA FLSH
200 Media set to MEDIA_FLASH
ftp> put bin/lantiq/openwrt-lantiq-xrx200-FRITZ7360SL-squashfs.image.eva mtd1
local: bin/lantiq/openwrt-lantiq-xrx200-FRITZ7360SL-squashfs.image.eva remote: mtd1
ftp: setsockopt (ignored): Permission denied
---> PASV
227 Entering Passive Mode (192,168,178,1,12,9)
---> STOR mtd1
150 Opening BINARY data connection
226 Transfer complete
5505028 bytes sent in 10.72 secs (501.6 kB/s)
ftp> exit
---> QUIT
221 Thank you for using the FTP service on ADAM2

* After flashing you can powercycle the Device

Photos

Opening the case

Logs

[    0.000000] Linux version 4.4.61 (lipkegu@Medice-PC) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3986-e1d433b) ) #0 SMP Fri Apr 21 05:50:55 2017
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is FRITZ7360SL - 1&1 HomeServer
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 08000000 @ 00000000 (usable)
[    0.000000] User-defined physical RAM map:
[    0.000000]  memory: 07e00000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000007dfffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000007dfffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007dfffff]
[    0.000000] On node 0 totalpages: 32256
[    0.000000] free_area_init_node: node 0, pgdat 80534e80, node_mem_map 81008480
[    0.000000]   Normal zone: 252 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32256 pages, LIFO batch:7
[    0.000000] Detected 1 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] PERCPU: Embedded 9 pages/cpu @8110b000 s8112 r8192 d20560 u36864
[    0.000000] pcpu-alloc: s8112 r8192 d20560 u36864 alloc=9*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32004
[    0.000000] Kernel command line: console=ttyLTQ0,115200 mem=126M vpe1_load_addr=0x87e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Writing ErrCtl register=00049ef0
[    0.000000] Readback ErrCtl register=00049ef0
[    0.000000] Memory: 120864K/129024K available (4071K kernel code, 164K rwdata, 1184K rodata, 1220K init, 223K bss, 8160K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] Setting up IPI vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000012] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007886] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.042410] pid_max: default: 32768 minimum: 301
[    0.047303] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053831] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.064064] Brought up 1 CPUs
[    0.072091] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.081790] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.088090] pinctrl core: initialized pinctrl subsystem
[    0.094087] NET: Registered protocol family 16
[    0.103777] pinctrl-xway 1e100b10.pinmux: Init done
[    0.109414] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.220140] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.337860] PCI host bridge /fpi@10000000/pcie@d900000 ranges:
[    0.372996] usbcore: registered new interface driver usbfs
[    0.378518] usbcore: registered new interface driver hub
[    0.383890] usbcore: registered new device driver usb
[    0.389371] PCI host bridge to bus 0000:00
[    0.393381] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff]
[    0.400295] pci_bus 0000:00: root bus resource [io  0x1d800000-0x1d8fffff]
[    0.407240] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.414095] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.422135] pci 0000:00:00.0: [1bef:0011] type 01 class 0x060000
[    0.422183] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[    0.439937] pci 0000:00:00.0: PME# supported from D0 D3hot
[    0.440583] pci 0000:01:00.0: [168c:ff1c] type 00 class 0x020000
[    0.440686] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff 64bit]
[    0.440870] pci 0000:01:00.0: supports D1
[    0.440892] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[    0.441213] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    0.441256] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01
[    0.441317] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
[    0.448022] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff 64bit]
[    0.455391] pci 0000:00:00.0: PCI bridge to [bus 01]
[    0.460403] pci 0000:00:00.0:   bridge window [mem 0x1c000000-0x1c0fffff]
[    0.467284] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1 
[    0.473932] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned
[    0.480287] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1 
[    0.486950] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[    0.499444] clocksource: Switched to clocksource MIPS
[    0.506326] NET: Registered protocol family 2
[    0.511614] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.518554] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.524912] TCP: Hash tables configured (established 1024 bind 1024)
[    0.531409] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.537266] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.543871] NET: Registered protocol family 1
[    0.548276] PCI: CLS 0 bytes, default 32
[    0.551837] gptu: totally 6 16-bit timers/counters
[    0.556784] gptu: misc_register on minor 63
[    0.560944] gptu: succeeded to request irq 126
[    0.565435] gptu: succeeded to request irq 127
[    0.569945] gptu: succeeded to request irq 128
[    0.574460] gptu: succeeded to request irq 129
[    0.578977] gptu: succeeded to request irq 130
[    0.583506] gptu: succeeded to request irq 131
[    0.588317] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.595515] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 7AA0000
[    0.601875] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 7AA0000
[    0.709938] genirq: Flags mismatch irq 0. 00000000 (RTLX) vs. 00000400 (IPI_resched)
[    0.719342] Crashlog allocated RAM at address 0x3f00000
[    0.751648] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.757494] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.773746] io scheduler noop registered
[    0.777658] io scheduler deadline registered (default)
[    0.783532] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.792464] console [ttyLTQ0] enabled
[    0.799784] bootconsole [early0] disabled
[    0.809000] lantiq nor flash device: 01000000 at 10000000
[    0.813162] ltq_nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e
[    0.822587] Amd/Fujitsu Extended Query Table at 0x0040
[    0.827716]   Amd/Fujitsu Extended Query version 1.3.
[    0.832750] number of CFI chips: 1
[    0.836185] 4 ofpart partitions found on MTD device ltq_nor
[    0.841716] Creating 4 MTD partitions on "ltq_nor":
[    0.846594] 0x000000000000-0x000000020000 : "urlader"
[    0.855528] 0x000000020000-0x000000f80000 : "firmware"
[    0.877876] 2 eva-fw partitions found on MTD device firmware
[    0.882163] 0x000000020000-0x0000001d0c2d : "kernel"
[    0.889244] 0x0000001e0100-0x000000f80000 : "rootfs"
[    0.895431] mtd: device 3 (rootfs) set to be root filesystem
[    0.899758] 1 squashfs-split partitions found on MTD device rootfs
[    0.905884] 0x0000008c0000-0x000000f80000 : "rootfs_data"
[    0.913796] 0x000000f80000-0x000000fc0000 : "tffs (1)"
[    0.920351] 0x000000fc0000-0x000001000000 : "tffs (2)"
[    1.030704] libphy: lantiq,xrx200-mdio: probed
[    1.106664] eth0: attached PHY [Atheros 8030 ethernet] (phy_addr=0:00, irq=-1)
[    1.174643] eth0: attached PHY [Atheros 8030 ethernet] (phy_addr=0:01, irq=-1)
[    1.243139] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    1.311137] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    1.420092] ltq-cputemp cputemp@0: Current CPU die temperature: 68.0 °C
[    1.425710] wdt 1f8803f0.watchdog: Init done
[    1.433122] NET: Registered protocol family 10
[    1.442260] NET: Registered protocol family 17
[    1.445487] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.457964] 8021q: 802.1Q VLAN Support v1.8
[    1.474943] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.482421] Freeing unused kernel memory: 1220K (8054f000 - 80680000)
[    4.454116] eth0: port 4 got link
[    4.772471] init: Can't open /sys/block/zram0/disksize: No such file or directory
[    4.779174] init: Console is alive
[    4.782236] init: - watchdog -
[    4.812562] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    4.908567] SCSI subsystem initialized
[    5.450802] eth0: port 1 got link
[    5.774822] dwc2 1e101000.ifxhcd: DWC OTG Controller
[    5.778399] dwc2 1e101000.ifxhcd: new USB bus registered, assigned bus number 1
[    5.785805] dwc2 1e101000.ifxhcd: irq 62, io mem 0x00000000
[    5.791292] dwc2 1e101000.ifxhcd: Hardware does not support descriptor DMA mode -
[    5.798698] dwc2 1e101000.ifxhcd: falling back to buffer DMA mode.
[    5.806744] hub 1-0:1.0: USB hub found
[    5.809539] hub 1-0:1.0: 1 port detected
[    6.670822] dwc2 1e106000.ifxhcd: DWC OTG Controller
[    6.674444] dwc2 1e106000.ifxhcd: new USB bus registered, assigned bus number 2
[    6.681786] dwc2 1e106000.ifxhcd: irq 91, io mem 0x00000000
[    6.687295] dwc2 1e106000.ifxhcd: Hardware does not support descriptor DMA mode -
[    6.694706] dwc2 1e106000.ifxhcd: falling back to buffer DMA mode.
[    6.702705] hub 2-0:1.0: USB hub found
[    6.705550] hub 2-0:1.0: 1 port detected
[    6.714183] usbcore: registered new interface driver usb-storage
[    6.719713] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    6.736619] init: - preinit -
[    7.338178] usb 2-1: new high-speed USB device number 2 using dwc2
[    7.594201] random: procd: uninitialized urandom read (4 bytes read, 33 bits of entropy available)
[    7.602649] usb-storage 2-1:1.0: USB Mass Storage device detected
[    7.627229] scsi host0: usb-storage 2-1:1.0
[    8.632126] scsi 0:0:0:0: Direct-Access     WD       My Book 1230     1065 PQ: 0 ANSI: 6
[    8.644782] scsi 0:0:0:1: Enclosure         WD       SES Device       1065 PQ: 0 ANSI: 6
[    8.652355] sd 0:0:0:0: [sda] Spinning up disk...
[    9.658568] .
[    9.904747] mount_root: loading kmods from internal overlay
[    9.944562] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[    9.953371] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[   10.293822] jffs2_scan_eraseblock(): End of filesystem marker found at 0x20000
[   10.299705] jffs2_build_filesystem(): unlocking the mtd device... done.
[   10.306209] jffs2_build_filesystem(): erasing all blocks after the end marker... 
[   10.662582] .......ready
[   16.870137] sd 0:0:0:0: [sda] 3906963456 512-byte logical blocks: (2.00 TB/1.82 TiB)
[   16.877538] sd 0:0:0:0: [sda] Write Protect is off
[   16.881324] sd 0:0:0:0: [sda] Mode Sense: 53 00 10 08
[   16.882309] sd 0:0:0:0: [sda] No Caching mode page found
[   16.886651] sd 0:0:0:0: [sda] Assuming drive cache: write through
[   17.040188]  sda: sda1 sda2 sda3
[   17.047993] sd 0:0:0:0: [sda] Attached SCSI disk
[   26.142603] random: nonblocking pool is initialized
[   43.742719] done.
[   43.743235] jffs2: notice: (466) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   43.759250] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   43.765849] block: unable to load configuration (fstab: Entry not found)
[   43.772541] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   43.778984] block: unable to load configuration (fstab: Entry not found)
[   43.785594] block: attempting to load /etc/config/fstab
[   43.791017] block: unable to load configuration (fstab: Entry not found)
[   43.797499] block: no usable configuration
[   43.869202] jffs2: notice: (463) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[   44.788584] block: attempting to load /tmp/jffs_cfg/upper/etc/config/fstab
[   44.794475] block: unable to load configuration (fstab: Entry not found)
[   44.801146] block: attempting to load /tmp/jffs_cfg/etc/config/fstab
[   44.807583] block: unable to load configuration (fstab: Entry not found)
[   44.814149] block: attempting to load /etc/config/fstab
[   44.819502] block: unable to load configuration (fstab: Entry not found)
[   44.826056] block: no usable configuration
[   44.831888] mount_root: overlay filesystem has not been fully initialized yet
[   44.840060] mount_root: switching to jffs2 overlay
[   46.180459] urandom-seed: Seed file not found (/etc/urandom.seed)
[   46.309829] procd: - early -
[   46.311724] procd: - watchdog -
[   46.545111] eth0: port 4 lost link
[   46.548473] eth0: port 1 lost link
[   47.048876] procd: - ubus -
[   47.104625] procd: - init -
[   47.807702] kmodloader: loading kernel modules from /etc/modules.d/*
[   47.821928] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[   47.832722] NET: Registered protocol family 8
[   47.835723] NET: Registered protocol family 20
[   47.851077] sit: IPv6 over IPv4 tunneling driver
[   47.867991] gre: GRE over IPv4 demultiplexor driver
[   47.876575] ip_gre: GRE over IPv4 tunneling driver
[   47.899325] PPP generic driver version 2.4.2
[   47.919317] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   47.977826] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG
[   47.977826] 
[   47.977826] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6
[   48.034857] 
[   48.034857] Predefined debug level: 3
[   48.072736] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[   48.079423] Backport generated by backports.git backports-20160324-13-g24da7d3c
[   48.122182] ip_tables: (C) 2000-2006 Netfilter Core Team
[   48.139003] Infineon Technologies DEU driver version 2.0.0 
[   48.160944] IFX DEU DES initialized (multiblock).
[   48.183138] IFX DEU AES initialized (multiblock).
[   48.191554] IFX DEU ARC4 initialized (multiblock).
[   48.202862] IFX DEU SHA1 initialized.
[   48.209712] IFX DEU MD5 initialized.
[   48.215739] IFX DEU SHA1_HMAC initialized.
[   48.223603] IFX DEU MD5_HMAC initialized.
[   48.234367] nf_conntrack version 0.5.0 (1907 buckets, 7628 max)
[   48.292844] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[   48.297309] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[   48.304161] owl-loader 0000:01:00.0: Direct firmware load for ath9k-eeprom-pci-0000:01:00.0.bin failed with error -2
[   48.313365] owl-loader 0000:01:00.0: Falling back to user helper
[   48.338155] PPP MPPE Compression module registered
[   48.348355] NET: Registered protocol family 24
[   48.357704] PPTP driver version 0.8.5
[   48.401587] xt_time: kernel timezone is -0000
[   48.604281] kmodloader: done loading kernel modules from /etc/modules.d/*
[   69.216243] ATM1.0.26    ATM (A1) firmware version 0.24
[   69.220123] ifxmips_atm: ATM init succeed
[   72.114611] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   72.158259] device eth0.1 entered promiscuous mode
[   72.161790] device eth0 entered promiscuous mode
[   72.200070] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   72.945650] eth0: port 4 got link
[   72.954937] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   73.073847] br-lan: port 1(eth0.1) entered forwarding state
[   73.078167] br-lan: port 1(eth0.1) entered forwarding state
[   73.262726] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   73.861533] IPv6: ADDRCONF(NETDEV_UP): nas0: link is not ready
[   73.942854] eth0: port 1 got link
[   75.078627] br-lan: port 1(eth0.1) entered forwarding state
[   86.951015] enter showtime, cell rate: 0 - 2716, 1 - 2716, xdata addr: 0xa60f0000
[   86.989369] enter showtime, cell rate: 0 - 2716, 1 - 2716, xdata addr: 0xa60f0000
[   87.138667] IPv6: ADDRCONF(NETDEV_CHANGE): nas0: link becomes ready
[   89.353868] pppoe-wan: renamed from ppp0
[   89.436164] owl-loader 0000:01:00.0: fixup device configuration
[   89.442926] pci 0000:01:00.0: [168c:002e] type 00 class 0x028000
[   89.443041] pci 0000:01:00.0: reg 0x10: [mem 0x1c000000-0x1c00ffff 64bit]
[   89.443244] pci 0000:01:00.0: supports D1
[   89.443271] pci 0000:01:00.0: PME# supported from D0 D1 D3hot
[   89.443693] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff 64bit]
[   89.449895] PCI: Enabling device 0000:01:00.0 (0140 -> 0142)
[   89.511623] ath: phy0: eeprom contains invalid mac address: 00:00:00:00:00:00
[   89.517435] ath: phy0: random mac address will be used: 86:18:bf:0a:4d:99
[   89.525716] ath: EEPROM regdomain: 0x8114
[   89.525742] ath: EEPROM indicates we should expect a country code
[   89.525759] ath: doing EEPROM country->regdmn map search
[   89.525775] ath: country maps to regdmn code: 0x37
[   89.525791] ath: Country alpha2 being used: DE
[   89.525805] ath: Regpair used: 0x37
[   89.539684] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   89.544507] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xbc000000, irq=144
[   99.054960] pppoe-wan: renamed from ppp0
[  218.025355] pptp-vpn: renamed from ppp1

xDSL Settings

In /etc/config/network use these settings for ADSL

config atm-bridge 'atm'
        option vpi '1'
        option vci '32'
        option encaps 'llc'
        option payload 'bridged'

config dsl 'dsl'
        option annex 'bdmt'
        option xfer_mode 'atm'
        option line_mode 'adsl'

config interface 'wan'
        option proto 'pppoe'
        option ipv6 'auto'
        option username 'username'
        option password 'password'
        option ifname 'nas0'

Telnet access

call #96*7* to enable telnetd or call #96*8* to disable the telnetd

JTAG

How to connect to JTAG interface, and how to reflash the device with JTAG tools

toh/avm/fritz.box.wlan.7360.txt · Last modified: 2017/04/23 09:36 by LipkeGu