You are here: OpenWrt Wiki » Table of Hardware » Aztech » Aztech GR7000

Aztech GR7000

Hardware Highlights

CPU	Ram	Flash	Network	USB	Serial	JTag
Lantiq XWAY ARX168 AR9 @ 333MHz	32MiB	8MiB	5 x 1	Yes	Yes	?

Info

Architecture:	MIPS32
Vendor:	soc.lantiq Lantiq
Bootloader:	U-Boot 1.1.5-LANTIQ-v-1.8.20
System-On-Chip:	Infineon/Lantiq XWAY ARX168
CPU/Speed	MIPS 34Kc / 333MHz
Flash-Chip:	Spansion S29GL064N90TF104
Flash size:	8MB
RAM:	32MB HYNIX H5DU2562GTR-E3C
Wireless:	Ralink RT3062F 802.11bgn
Ethernet:	Atheros AR8316 5 x Gigabit
USB:	Yes 2 x 2.0 (driver dwc_otg)
Serial:	Yes
JTAG:	Yes

Original Flash Layout

→flash.layout for explanations!

dev:	size	erasesize	name
mtd0:	00010000	00002000	"u-boot"
mtd1:	007f0000	00010000	"rootfs"

Serial

Pinout

Now connect a serial hack adapter (DKU-5, CA-42 or similar containing the PL-2303 chip) and away you go!
The right settings for accessing the serial console are as follows:

Bits per second: 115200
Data bits: 8
Stop bits: 1
Parity: None
Flow control: None

CPU Info

system type             : AR9
processor               : 0
cpu model               : MIPS 34K V4.12
BogoMIPS                : 222.00
wait instruction        : yes
microsecond timers      : yes
tlb_entries             : 16
extra interrupt vector  : yes
hardware watchpoint     : yes
ASEs implemented        : mips16 dsp mt
VCED exceptions         : not available
VCEI exceptions         : not available

BootLog

ROM VER: 1.1.3
CFG 01
DDR Access auto data-eye tuning Rev 0.1a
DDR size from 0xa0000000 - 0xa1ffffff
DDR check ok... start booting...



U-Boot 1.1.5-LANTIQ-v-1.8.20 (Aug 19 2010 - 09:13:40)

Boot from NOR flash
AR9 BOARD
CLOCK CPU 333M RAM 166M
DRAM:  32 MB

 relocate_code start
 relocate_code finish.
Flash:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:
switch chip id=0000ffff
amazon_s Switch

Type "run flash_nfs" to mount root filesystem over NFS

Hit any key to stop autoboot:  0
## Booting image at b06d78f0 ...
   Image Name:   MIPS IFXCPE Linux-2.6.20.19
   Created:      2010-11-02   9:36:09 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1140432 Bytes =  1.1 MB
   Load Address: 80002000
   Entry Point:  80349000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80349000) ...
## Giving linux memsize in MB, 32

Starting kernel ...

Infineon xDSL CPE AR9
mips_hpt_frequency = 166666666, counter_resolution = 2
drivers/char/ifxmips_rcu.c:668:ifx_rcu_init: Can not register RCU device - -16

IFX CPE login: DAS 2434
BOOTLoader:1.1.5-LANTIQ-v-1.8.20
CPU:AR9-v
Kernel:2.6.20.19
Software:UGW-4.2.1-832-1736-02Nov10
Tool Chain:3.4.6/0.9.29
The pid file is: /var/run/wscd.pid.ra0!
gPassiveMsgQ Init success! gPassiveMsgID=0x4c3b5f41!
gActiveMsgQ Init success!
sock=5!(0x0x7ffd7128)
Pthread(wscDevNLHandle)Now waiting for the netlink socket incoming message!
Create netlink socket thread success!
Create ioctl socket(6) success!
.
Error with UpnpInit -- -208
[: 1: unknown operand
Bringup wan started for wan index 1 !!
SIOCSIFADDR: No such device
SIOCGIFFLAGS: No such device
[: -lt: argument expected
SIOCGIFFLAGS: No such device
/usr/sbin/pppd: In file /etc/ppp/peers/pppoe1: unrecognized option 'eth1.3'
cat: /tmp/adsl_status: No such file or directory
Bringup wan started for wan index 2 !!
SIOCSIFADDR: No such device
SIOCGIFFLAGS: No such device
udhcpc (v0.9.9-pre) started
cat: /tmp/adsl_status: No such file or directory
Sending discover...
Sending discover...
Sending discover...
No lease, forking to background.

IFX CPE login: admin
Password:


BusyBox v1.00 (2010.11.02-08:56+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

# uname -a
Linux Aztech 2.6.20.19 #1 Tue Nov 2 17:31:28 SGT 2010 mips unknown

OpenWrt

Wiki Search

Actions

Donate

Translations