User Tools

Site Tools


toh:aztech:gr7000

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

toh:aztech:gr7000 [2012/09/23 11:23]
toh:aztech:gr7000 [2015/09/26 13:26] (current)
tmomas Picture links corrected + resized
Line 1: Line 1:
 +====== Aztech GR7000 ======
  
 +===== Hardware Highlights =====
 +^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^
 +| Lantiq XWAY ARX168 AR9 @ 333MHz | 32MiB | 8MiB | 5 x 1| Yes | Yes | Yes |
 +
 +==== Info ====
 +| **[[wp>​Instruction set|Architecture]]:​** ​   | [[wp>​MIPS architecture|MIPS32]] |
 +| **Vendor:​** ​         | [[doc:​hardware:​soc:​soc.lantiq]] [[wp>​Lantiq]] |
 +| **[[doc:​techref:​Bootloader]]:​** ​    | U-Boot 1.1.5-LANTIQ-v-1.8.20 |
 +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​ | Infineon/​Lantiq XWAY ARX168 |
 +| **[[doc:​hardware:​cpu|CPU]]/​Speed** ​       | MIPS 34Kc / 333MHz |
 +| **Flash-Chip:​** ​     | Spansion S29GL064N90TF104 |
 +| **Flash size:​** ​     | 8MB |
 +| **RAM:​** ​            | 32MB HYNIX H5DU2562GTR-E3C ​ |
 +| **Wireless:​** ​       | Ralink RT3062F 802.11bgn |
 +| **Ethernet:​** ​       | Atheros AR8316 5 x Gigabit |
 +| **USB:​** ​            | Yes 2 x 2.0 (driver dwc_otg) ​   |
 +| **[[doc:​hardware:​port.serial|Serial]]:​** | [[#​Serial|Yes]] |
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​    | [[#​JTAG|Yes]] ​ |
 +
 +==== Original Flash Layout ====
 +->​[[doc:​techref:​flash.layout]] for explanations!
 +
 +^dev:^ size^erasesize^name^
 +|mtd0:| 00010000 | 00002000 |"​u-boot"​ |
 +|mtd1:| 007f0000 | 00010000 |"​rootfs"​ |
 +
 +==== Serial ====
 +== Pinout ==
 +
 +Now connect a [[http://​buffalo.nas-central.org/​index.php/​Use_a_Nokia_Serial_Cable_on_an_ARM9_Linkstation#​Preparing_the_Cable|serial hack adapter]] (DKU-5, CA-42 or similar containing the PL-2303 chip) and away you go!\\
 +The right settings for accessing the serial console are as follows:
 +
 +Bits per second: **115200**\\
 +Data bits: **8**\\
 +Stop bits: **1**\\
 +Parity: **None**\\
 +Flow control: **None**\\
 +
 +==== CPU Info ====
 +<​code>​
 +system type             : AR9
 +processor ​              : 0
 +cpu model               : MIPS 34K V4.12
 +BogoMIPS ​               : 222.00
 +wait instruction ​       : yes
 +microsecond timers ​     : yes
 +tlb_entries ​            : 16
 +extra interrupt vector ​ : yes
 +hardware watchpoint ​    : yes
 +ASEs implemented ​       : mips16 dsp mt
 +VCED exceptions ​        : not available
 +VCEI exceptions ​        : not available
 +</​code>​
 +
 +==== BootLog ====
 +<​code>​
 +ROM VER: 1.1.3
 +CFG 01
 +DDR Access auto data-eye tuning Rev 0.1a
 +DDR size from 0xa0000000 - 0xa1ffffff
 +DDR check ok... start booting...
 +
 +
 +
 +U-Boot 1.1.5-LANTIQ-v-1.8.20 (Aug 19 2010 - 09:13:40)
 +
 +Boot from NOR flash
 +AR9 BOARD
 +CLOCK CPU 333M RAM 166M
 +DRAM:  32 MB
 +
 + ​relocate_code start
 + ​relocate_code finish.
 +Flash: ​ 8 MB
 +In:    serial
 +Out:   ​serial
 +Err:   ​serial
 +Net:
 +switch chip id=0000ffff
 +amazon_s Switch
 +
 +Type "run flash_nfs"​ to mount root filesystem over NFS
 +
 +Hit any key to stop autoboot: ​ 0
 +## Booting image at b06d78f0 ...
 +   Image Name:   MIPS IFXCPE Linux-2.6.20.19
 +   ​Created: ​     2010-11-02 ​  ​9:​36:​09 UTC
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +   Data Size:    1140432 Bytes =  1.1 MB
 +   Load Address: 80002000
 +   Entry Point: ​ 80349000
 +   ​Verifying Checksum ... OK
 +   ​Uncompressing Kernel Image ... OK
 +No initrd
 +## Transferring control to Linux (at address 80349000) ...
 +## Giving linux memsize in MB, 32
 +
 +Starting kernel ...
 +
 +Infineon xDSL CPE AR9
 +mips_hpt_frequency = 166666666, counter_resolution = 2
 +drivers/​char/​ifxmips_rcu.c:​668:​ifx_rcu_init:​ Can not register RCU device - -16
 +
 +IFX CPE login: DAS 2434
 +BOOTLoader:​1.1.5-LANTIQ-v-1.8.20
 +CPU:AR9-v
 +Kernel:​2.6.20.19
 +Software:​UGW-4.2.1-832-1736-02Nov10
 +Tool Chain:​3.4.6/​0.9.29
 +The pid file is: /​var/​run/​wscd.pid.ra0!
 +gPassiveMsgQ Init success! gPassiveMsgID=0x4c3b5f41!
 +gActiveMsgQ Init success!
 +sock=5!(0x0x7ffd7128)
 +Pthread(wscDevNLHandle)Now waiting for the netlink socket incoming message!
 +Create netlink socket thread success!
 +Create ioctl socket(6) success!
 +.
 +Error with UpnpInit -- -208
 +[: 1: unknown operand
 +Bringup wan started for wan index 1 !!
 +SIOCSIFADDR:​ No such device
 +SIOCGIFFLAGS:​ No such device
 +[: -lt: argument expected
 +SIOCGIFFLAGS:​ No such device
 +/​usr/​sbin/​pppd:​ In file /​etc/​ppp/​peers/​pppoe1:​ unrecognized option '​eth1.3'​
 +cat: /​tmp/​adsl_status:​ No such file or directory
 +Bringup wan started for wan index 2 !!
 +SIOCSIFADDR:​ No such device
 +SIOCGIFFLAGS:​ No such device
 +udhcpc (v0.9.9-pre) started
 +cat: /​tmp/​adsl_status:​ No such file or directory
 +Sending discover...
 +Sending discover...
 +Sending discover...
 +No lease, forking to background.
 +
 +IFX CPE login: admin
 +Password:
 +
 +
 +BusyBox v1.00 (2010.11.02-08:​56+0000) Built-in shell (ash)
 +Enter '​help'​ for a list of built-in commands.
 +
 +# uname -a
 +Linux Aztech 2.6.20.19 #1 Tue Nov 2 17:31:28 SGT 2010 mips unknown
 +</​code>​
 +
 +===== Photos =====
 +{{:​media:​aztech:​aztech_gr7000_board.jpg?​400|}}
 +
 +{{:​media:​aztech:​aztech_gr7000_soc.jpg?​200|}}
 +{{:​media:​aztech:​aztech_gr7000_flash.jpg?​200|}}
 +{{:​media:​aztech:​aztech_gr7000_wifi.jpg?​200|}}
 +{{:​media:​aztech:​aztech_gr7000_switch.jpg?​200|}}
 +
 +===== Tags =====
 +{{tag>​ADSL2+ lantiq ar9}}