F7D3302 and F7D7302

Bootloader refers to `WG7016F22 1-LF-AK`

Versions

Version/Model Launch Date S/N OpenWrt Version Supported Model Specific Notes
F7D7302 v1 - - WIP Noted on the internet as identical to the F7D3302
F7D3302 v1 - - WIP -

WIP openwrt patches: https://github.com/jmesmon/openwrt.git belkin

OEM source code available at: http://cache-www.belkin.com/support/dl/Belkin-F7D3302-v1.00.25.tgz

Hardware Highlights

SoC Ram Flash Network USB Serial JTag
Broadcom 4718 64MiB 16MiB 4 x 1 Yes Yes Probably, untested

Bootloader

Defaults to ip addr 192.168.2.1 after a nvram reset. Changing the ip in the manufacturure firmware also changes the bootloader ip.

CFE version observered HW rev
0.09e F7D7302 v1

Manuf MTD layout

0x00000000-0x00030000 : "boot"
0x00030000-0x007f0000 : "linux"
0x001b7bc4-0x007f0000 : "rootfs"
0x007f0000-0x00800000 : "nvram"

Keep the articles modular

Please include only model specific information, omit bla,bla and put everything generic into separate articles
generic.overview if you have no time to write certain stuff link to this
basic.config should lead the way, do not explain this again
DO NOT provide a complete howto here! Instead groom the general HowTos.

Installation

  1. »»»»here»»»»Latest OpenWrt release««««here«««« DO NOT PROVIDE OWN LINKS to http://downloads.openwrt.org/

Flash Layout

Please check out the article Flash Layout. It contains an example and a couple of explanations.

OEM easy installation

This section deals with how you install OpenWrt from a device freshly opened.

Note: Reset router to factory defaults if it has been previously configured.

  • Select "Firmware Update" under "Utilities" in the left column
  • If prompted to authenticate, leave the password entry field blank and continue
  • Select openwrt-f7d3302-squashfs.bin
  • Click Update. Yes, you are sure.
  • Wait for it to reboot (if the WAN is disconnected, this is indicated by a switch from an orange flashing light to a green light)
  • Telnet to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

OEM installation using the TFTP method

Specific values you need

Bootloader tftp server IPv4 address 192.168.2.1
Bootloader MAC address (special) FILL-IN
Firmware tftp image Latest OpenWrt release (NOTE: Either the one containing the model name, or the "f7dxxxx-qa")
TFTP Transfer Window (NONE, AFICT)
TFTP Window Start approximately FILL-IN seconds after power on
TFTP Client Required IP Address FILL-IN

Upgrading OpenWrt

generic.sysupgrade

If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

LuCI Web Upgrade Process

Terminal Upgrade Process

  • Login as root via SSH on 192.168.1.1
  • Use the following commands to upgrade.
WARNING: this snapshot does not yet exist

cd /tmp/
wget http://http://downloads.openwrt.org/snapshots/trunk/brcm47xx/openwrt-f7d3302-squashfs.bin
sysupgrade /tmp/openwrt-f7d3302-squashfs.bin

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
vlan1 (eth0.1) LAN ports (1 to 4) None
vlan2 (eth0.2) WAN port DHCP
phy0 WiFi Disabled

Switch Ports (for VLANs)

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
CPU (internal) 5
WAN 4
LAN 1 3
LAN 2 2
LAN 3 1
LAN 4 0

Failsafe mode

Buttons

hardware.button on howto use and configure the hardware button(s).

BUTTON Event
Reset reset
WPS wps

Hardware

Info

Instruction set: MIPS
Vendor: Broadcom
Bootloader: CFE
System-On-Chip: BCM4718A1KFBG
CPU @Frq MIPS 74K V4.0 @453 MHz
Flash size: 8MiB
Flash Chip: ???
RAM size: 64MiB
RAM Chip: EtronTech EM68B16CWPA
Wireless No1: SoC-integrated: Unknown Broadcom integrated IC for 2.4GHz 802.11b/g/n
Switch: Broadcom BCM5325EKQMG (100M, VLAN)
USB: Yes 1 x 2.0
Serial: Yes
JTAG: Yes

Photos

Model Number

Front:

Photo of front of the casing

Back:

Photo of back of the casing

Opening the case

Note: This will void your warranty!

  • There are a number of large tabs holding the case closed
  • I haven't found a good way to open it, I just pryed mine rather violently.

Main PCB

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

  • Look for a set of 4 pins labeled "J3" next to a large JTAG connector labeled "J2"
  • On my board, the headers of J3 were already populated
  • Pinout:
    1. 3.3v
    2. Tx (from router to computer)
    3. Rx (from computer to router)
    4. GND

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:

Photo of PCB with markings

Debricking

generic.debrick

On the serial console:

flash -noheader : flash1.trx

Imediately after that is entered, on a computer connected to the first lan port (check other ports for functionality), and with the ip address configured to 192.168.2.8

curl -T openwrt-f7d3302-squashfs.trx tftp://192.168.2.1

Bootloader Mods

  1. you could read about bootloader in general

Hardware mods

  1. as a beginner, you really should inform yourself about soldering in general and then obtain some practical experience!

Add a second USB port

  1. should be possible. Kernel enumerates 2 usb ports, and pads exist on the board. It appears we need a fuse, inductor, 2 resistors, and the port itself to get a second usb working.

Bootlogs

OEM bootlog

Decompressing...done Decompressing...done Init Arena Init Devs. Boot partition size = 131072(0x20000) et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.128.0 CPU type 0x19740: 453MHz Tot mem: 65536 KBytes CFE mem: 0x80700000 - 0x8079B620 (636448) Data: 0x807326D0 - 0x80734A80 (9136) BSS: 0x80734A80 - 0x80735620 (2976) Heap: 0x80735620 - 0x80799620 (409600) Stack: 0x80799620 - 0x8079B620 (8192) Text: 0x80700000 - 0x807326C4 (206532) Copying boot params..... DONE Bootloader version 0.09e boot_version 0.09e Project name : WG7016F22 1-LF-AK Press space bar to cancel startup... Device eth0: hwaddr 94-44-52-B9-7E-2B, ipaddr 192.168.1.102, mask 255.255.255.0 gateway not set, nameserver not set Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) Loading: ....... 4165296 bytes read Entry at 0x80001000 Closing network. Starting program at 0x80001000 Linux version 2.6.22 (andrew_chen@SW3SRV2.arcadyan.com.tw) (gcc version 4.1.2) #6 Mon Aug 30 19:36:15 CST 2010 CPU revision is: 00019740 Found chip type AI (0x19a14716) Chipc: rev 31, caps 0x184807c9, chipst 0x9400 pmurev 5, pmucaps 0x11242c05 No PLL init done for chip 4716 rev 1 pmurev 5 si_kattach done. ccrev = 31, wd_msticks = 32 Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Built 1 zonelists. Total pages: 16256 Kernel command line: root=/dev/mtdblock2 console=ttyS0,115200 init=/sbin/preinit Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, linesize 32 bytes. Synthesized TLB refill handler (20 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB modify handler fastpath (31 instructions). PID hash table entries: 256 (order: 8, 1024 bytes) CPU: BCM4716 rev 1 at 453 MHz Using 226.500 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 60664k/65536k available (2805k kernel code, 4812k reserved, 1126k data, 132k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using membase 8000000 PCI: Initializing host PCI: Reset RC PCI: Fixing up bus 0 PCI: Fixing up bridge PCI: Fixing up bridge PCI: Enabling device 0000:01:00.1 (0004 -> 0006) PCI: Fixing up bus 1 Time: MIPS clocksource has been installed. NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered gpio_init 478 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher fuse init (API version 7.8) io scheduler noop registered (default) Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 8) is a 16550A loop: module loaded PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 Physically mapped flash: Found 1 x16 devices at 0x0 in 8-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Flash device: 0x800000 at 0x1c000000 Physically mapped flash: squash filesystem with lzma found at block 1758 Creating 4 MTD partitions on "Physically mapped flash": 0x00000000-0x00030000 : "boot" 0x00030000-0x007f0000 : "linux" 0x001b7bc4-0x007f0000 : "rootfs" 0x007f0000-0x00800000 : "nvram" Found a 0MB serial flash sflash: found no supported devices usbmon: debugfs is not available GACT probability on Mirror/redirect action on u32 classifier input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (512 buckets, 4096 max) ctnetlink v0.93: registering with nfnetlink. BCM fast NAT: INIT ip_tables: (C) 2000-2006 Netfilter Core Team ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 132k freed Warning: unable to open an initial console. Algorithmics/MIPS FPU Emulator v1.5 [sighandler]: No more events to be processed, quitting. [cleanup]: Waiting for children. [cleanup]: All children terminated. Hit enter to continue...waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes vlan2: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Operation not supported eth1: Invalid argument eth1: Invalid argument eth1: Operation not supported eth1: Invalid argument eth1: Invalid argument waitpid: No child processes waitpid: No child processes brctl: No child processes waitpid: No child processes waitpid: No child processes waitpid: No child processes HTTPD: main(963) udhcpd_main(138): udhcp server (v0.9.8) started UPnP daemon is ready to run Reaped 317 killall: wps_monitor: no process killed waitpid: No child processes killall: wps_ap: no process killed killall: wps_enr: no process killed mkdir: cannot create directory '/tmp/mnt': File exists mkdir: cannot create directory '/tmp/etc': File exists mkdir: cannot create directory '/tmp/etc/sysconfig': File exists Starting HotPlug: /usr/sbin/hotplugd -D -f Starting jcpd daemon: /usr/sbin/jcpd share memory key=74565 successful id on creating=32769 sh: /usr/sbin/httpd_watchdog: not found original zone=GMT+8 modified dst=GMT [start_wan 1136], ifconfig vlan1 up vlan1: Operation not supported waitpid: No child processes waitpid: No child processes udhcpc_main(438): udhcp client (v0.9.8) started original zone=GMT+8 modified dst=GMT vlan1 dhcp vlan1: No such process Stop DDNS service! Hit enter to continue...connect: Network is unreachable Hit enter to continue...Starting Samba: /usr/sbin/smbd -D /usr/sbin/nmbd -D Setting SSID "belkin.4e4b" main(1152) wl -i eth1 ssid -C 11 belkin.4e4b start_wl(994) reStart the Wireless, lan_ifNames=vlan2 eth1 start_wl(1031), name=vlan2 start_wl(1031), name=eth1 Starting sxuptpd Initializing USB port mode: port1 = NAS port2 = NAS Starting usbjcpd Hit enter to continue...original zone=GMT+8 modified dst=GMT Portrd: Add iptable command: iptables -t nat -A POSTROUTING -s 192.168.1.0/24 -o vlan1 -j MASQUERADE iptables -t nat -A POSTROUTING -s 192.168.169.0/24 -o vlan1 -j MASQUERADE Hit enter to continue...

Hitting enter drops to BusyBox v1.7.2 (2010-08-30 20:06:26 CST)

NVRAM dump

Terminal ready nvram show sb/1/ofdm2gpo=0x44444444 wl_radius_port=1812 auto_mode_5g=1 wan_unit=0 wl0_wmf_bss_enable=1 wan0_primary=1 pci/1/1/mcs5gpo0=0x0 pci/1/1/stbcpo=0 wan_route= ses_wds_mode=1 wl0_frameburst=on pci/1/1/mcs5gpo1=0x0 wl_txstreams=0 access_control_enabled=0 pci/1/1/mcs5gpo2=0x0 pci/1/1/maxp5gha0=0x32 wan_pppoe_keepalive=0 wan_pptp_ip= filter_client_url0= health_week=0 wan0_ipaddr=1.0.0.1 pci/1/1/mcs5gpo3=0x0 pci/1/1/maxp5gha1=0x32 log_ipaddr= wan0_proto=dhcp boardrev=0x1102 br0_ifnames=vlan2 eth1 wl0.14_hwaddr=96:44:52:B9:7E:29 pci/1/1/aa5g=0x3 wl_nctrlsb=lower wan0_pptp_dhcp=dhcp sb/1/mcs2gpo0=0x6666 wl_version=5.10.128.0 wl0_leddc=0x640000 et0macaddr=94:44:52:B9:7E:2B sb/1/mcs2gpo1=0x6666 ddns_enable=disabled sb/1/mcs2gpo2=0x6666 sb/1/mcs2gpo3=0x6666 wl0_akm=psk psk2 wl0_radarthrs=0 0x6a8 0x6c8 0x6ac 0x6c7 pci/1/1/pa5glw2a0=0xfa8e sb/1/mcs2gpo4=0x6666 wan_pppoe_passwd= wl_maxassoc=128 health_days=0 0 1 0 0 0 0 wl0_guest_mode=0 wan0_dns=12.213.224.61 watchdog=3000 boot_wait=on pci/1/1/pa5glw2a1=0xfabc sb/1/mcs2gpo5=0x6666 sb/1/mcs2gpo6=0x6666 wps_modelname=F7D7302 v1 wl_phytypes= wl_leddc=0x640000 wl0_infra=1 sb/1/mcs2gpo7=0x6666 bt_autoDelTorrent=1 wl0_country_code=US fw_disable=0 dhcp_client_list_num=0 emf_rtport_entry= bt_autoRateControl=1 wps_config_command=0 gs_remote_mgmt=0 gs_dmzEnable=0 gui_version=1.00.23 ddns_wildcard= wl_infra=1 reset_gpio=6 ses_event=2 ddns_server=0 wan0_bigpond_passwd= wl0_bcn_rotate=1 pmon_ver=CFE 5.10.128.0 bw_maxTx=100000000 restore_defaults=0 wan0_ifname=vlan1 vlan2ports=0 1 2 3 5* health_enable=1 wl0.1_hwaddr=96:44:52:B9:7E:2C schedule_reboot_status=0 wan0_pptp_demand=0 wl0_wme_sta_be=15 1023 3 0 0 off off wl0_nctrlsb=lower pci/1/1/cddpo=0 wan_lease=86400 wan_pppoe_service= wl0_version=5.10.128.0 sb/1/triso2g=3 wl_wme_apsd=on sb/1/sromrev=8 http_wanport=8080 wl_radius_ipaddr= ddns_hostname= eco_wlan_start=0 wl0.7_hwaddr=96:44:52:B9:7E:22 lan_gateway=192.168.1.102 wl0_ifname=eth1 dst_time_zone=GMT lan_domain=Belkin wl0_wme_sta_bk=15 1023 7 0 0 off off timer_interval=3600 dhcp_reserveIndex=0 pci/1/1/ag1=2 wan_bigpond_sindex=0 bt_autoHideMode=1 lan1_ipaddr=192.168.169.1 forward_port0= wl_net_reauth=900 wl0_rxstreams=0 gpio4=robo_reset ses_enable=1 obscurePSK_guest=1 wan_pppoe_mru=1492 health_time=7 lan_route= wl0_mrate=0 wps_device_pin=08890948 gpio8=wps_button time_zone_index=4 wl1_channel=0 wps_hw_enable=1 wl0_mode=ap pci/1/1/pa5gw2a0=0xFAFA wan_gateway=1.0.0.1 reboot_from_self_healing=1 serial=0 pci/1/1/pa5gw2a1=0xFAAA sb/1/pa2gw2a0=0xFACB dhcp_start=192.168.1.2 sb/1/pa2gw2a1=0xFAB8 wl0_ap_isolate=0 lan1_route= dlna_backup_ignore=0 pci/1/1/pa5ghw2a0=0xfac3 dhcp_end=192.168.1.100 wl_mrate=0 wan_bigpond_enable=0 wan0_pptp_subnet= pci/1/1/pa5ghw2a1=0xFAC3 sb/1/itt2ga0=0x20 wl_wmf_bss_enable=1 wl_akm=psk psk2 wps_get_stauts=0 wl0.15_hwaddr=96:44:52:B9:7E:2A wl0_wme_no_ack=off wl0_ampdu=auto wl0_gmode=1 sb/1/itt2ga1=0x20 login_timeout=10 eco_led_dim=1 boardtype=0xa4cf is_default=0 wl_wme_bss_disable=0 wl_ampdu_rr_rtylimit_tid=2 2 2 2 2 2 2 2 wl0_nband=2 wan0_bigpond_srver= wl_gmode=1 wl_ampdu=auto wps_uuid=5A18F382E1326BD3A4C3247B66DE83ED ddns_password= stats_server= pci/1/1/itt5ga0=0x3e pci/1/1/rxchain=3 eco_wlan=0 bw_peekTx=125000000 wl0_nreqd= pci/1/1/itt5ga1=0x3e lan_netmask=255.255.255.0 wps_enr_mode=disabled wl0_wme_txp_be=7 3 4 2 0 lan1_ifname=br1 wan_pptp_demand=0 wl_nband=2 wl0_dtim=3 wl0_ssid=belkin.4e4b lan1_hwnames= wan_pptp_hostname= http_username= wl_wme_sta_vi=7 15 2 6016 3008 off off wan0_pppoe_ifname= pci/1/1/maxp5ga0=0x32 wl_nreqd= wl_wme_ap_be=15 63 3 0 0 off off wan_bigpond_user_name= wl0_dfs_preism=60 pci/1/1/maxp5ga1=0x32 os_date=Aug 30 2010 lan_ap_ipaddr=192.168.2.254 sb/1/regrev=97 access_control_member0= wl0_wme_txp_bk=7 3 4 2 0 pci/1/1/ofdm5gpo0=0x0 sb/1/ag0=2 http_lanport=80 pci/1/1/ofdm5gpo1=0x0 pci/1/1/pdetrange5g=4 sb/1/ag1=2 wl_plcphdr=long wl_wme_sta_vo=3 7 2 3264 1504 off off landing_password= lan1_wins= wl_macmode=disabled wl_mimo_preamble= nvram_version=1 wan_hwname= wan_domain= wl_wme_ap_bk=15 1023 7 0 0 off off wl0_key1= wan0_pptp_enable=0 lan_lease=-1 wan_netmask=255.0.0.0 wl_phytype=n wl0_vlan_prio_mode=off wl0_key2= wan0_hostname= wl_lazywds=0 wl0.2_hwaddr=96:44:52:B9:7E:2D wl0_key3= wl_dfs_postism=60 wl0_key4= filter_client0= wps_default_pin=08890948 lan1_lease=86400 filter_maclist= pci/1/1/boardflags=0x200 wl_auth_mode=none wl0.8_hwaddr=96:44:52:B9:7E:23 vlan2hwname=et0 wan_pptp_subnet= wl0_bridge= wl0_hw_rxchain=3 pci/1/1/pa5glw1a0=0x1637 http_passwd= wl_wpa_psk=d4e9764a wl_guest_passwd=a96d4e6d47 pci/1/1/pa5glw1a1=0x1591 sb/1/extpagain2g=2 bt_torrentFolder=torrent lan_stp=1 wan_pppoe_demand=0 nat_type=cone wl0_wme_ap_vi=7 15 1 6016 3008 off off wan0_pptp_idletime=5 wl0_bss_maxassoc=128 wl_mode=ap igmp_proxy_func=1 wan0_pppoe_passwd= gs_sku_id=51 wl0_tpc_db= wl0_plcphdr=long wl0_rate=0 wl0_closed=0 wan_pptp_gateway= wl0.10_hwaddr=96:44:52:B9:7E:25 wl0_macmode=disabled xtalfreq=20000 wan_dns_auto=1 wl_wpa_gtk_rekey=0 wl0_wme_ap_vo=3 7 1 3264 1504 off off wl0_radioids=BCM2056 wan0_pptp_ip= sb/1/stbcpo=0 lan_dhcp=0 wps_unconfig_addenr=0 wl0_phytype=n wl_wme_txp_vi=7 3 4 2 0 qos_1=0 wl0_lazywds=0 qos_2=1 qos_3=2 usb_mounted_nodes= qos_4=3 wps_proc_status=0 wan0_pppoe_keepalive=0 boardflags2=0x1402 sb/1/bwduppo=0 sb/1/aa2g=3 wl0_afterburner=off sb/1/txchain=3 wl_wme_txp_vo=7 3 4 2 0 wl0_antdiv=-1 lan_hwaddr=94:44:52:B9:7E:2B wl_wds_timeout=1 ddns_started=0 wan_dns= filter_client_srv0= wl_wps_mode=enabled wan0_pppoe_ac= pci/1/1/bw40po=0 wan_pptp_enable=0 wl_ssid=belkin.4e4b wl_dtim=3 project_id=00n2 wl0_wpa_psk=d4e9764a pci/1/1/sromrev=8 wan_pppoe_mtu=1454 wl_radarthrs=0 0x6a8 0x6c8 0x6ac 0x6c7 ac_schedule0=inactive wait_time=3 bt_autoHideSec=86400 ac_schedule1=inactive wan0_pppoe_ip=0.0.0.0 ac_schedule2=inactive gs_silex=1 wl0_amsdu=auto wan0_pptp_username= ac_schedule3=inactive wan0_pppoe_dhcp=dhcp bt_torrentDLimit=50 ac_schedule4=inactive dhcp_wins=wan ac_schedule5=inactive os_server= ac_schedule6=inactive check_health=1 ac_schedule7=inactive pci/1/1/pa5gw1a0=0x143B wan_proto=dhcp wan_pptp_serviceip= wl_key1= wl_amsdu=auto ac_schedule8=inactive pci/1/1/pa5gw1a1=0x1664 sb/1/pa2gw1a0=0x15A4 wl_key2= ac_schedule9=inactive wl0_unit=0 wan0_pppoe_mru=1492 sb/1/pa2gw1a1=0x1639 wl_key3= wl_country_code=US wl_key4= pci/1/1/pa5ghw1a0=0x16be wl_hwaddr= wl0.3_hwaddr=96:44:52:B9:7E:2E pci/1/1/pa5ghw1a1=0x16BE wl_rxchain=3 wl0_net_reauth=900 wl0_bss_enabled=0 sb/1/boardflags2=0x1402 wl_vlan_prio_mode=off remote_mgmt_enabled=0 wps_count=0 gs_wftp_enabled=0 bt_torrentExitHour=1 wl0_nmode=-1 lan1_stp=1 wps_timeout_enable=0 wl0.9_hwaddr=96:44:52:B9:7E:24 board_version=01 wan_pppoe_idletime=5 wps_restart=0 wan0_bigpond_sindex=0 wl_nmode=-1 gs_domainName=Belkin bt_torrentULimit=20 lan1_gateway=192.168.169.1 remote_mgmt_ip= serial_number=121037G3118844 wl_rxstreams=0 ses_cl_enable=1 wl_wps_reg=enabled wl0_wds= wl_rate=0 wan0_gateway=72.173.128.1 log_level=0 wl0_reg_mode=off ntp_server=192.43.244.18 192.5.41.41 133.100.9.2 wan_hwaddr= wps_mfstring=Belkin International wl0.11_hwaddr=96:44:52:B9:7E:26 wan0_bigpond_enable=0 lan_ifnames=vlan2 eth1 bandwidth_var_5=1 first_bootup=0 qosname1=Voice Device wl0_radius_port=1812 wl0_wme=on wl0_auth=0 access_control_need_update=0 wan_bigpond_srver= qosname2=Online Games qosname3=Video wl0_rxchain=3 wl0_radius_ipaddr= wl0_wme_bss_disable=0 qosname4=Default wl0_wme_sta_vi=7 15 2 6016 3008 off off pci/1/1/boardflags2=0x0 ure_disable=1 sb/1/boardflags=0x310 wan_pppoe_username= sb/1/leddc=0xffff wan_ifnames=vlan1 wl0_wme_sta_vo=3 7 2 3264 1504 off off wan0_domain=wildblue.com wan0_hwname= pci/1/1/ledbh0=0 wl_rateset=12 wl_crypto=aes pci/1/1/ledbh1=0xffff wan_pptp_connect_id=0 pci/1/1/pa5glw0a0=0xfe87 pci/1/1/ledbh2=0xffff wl_guest_timeout=720 wl0_wps_reg=enabled pci/1/1/pa5glw0a1=0xfe9a pci/1/1/ledbh3=0xffff eco_mode=0 lan_ipaddr=192.168.1.102 clkfreq=453,226,113 os_name=linux lan_proto=static wl_radius_key= allow_remote_ip=1 wl0_maxassoc=128 vlan1hwname=et0 lan1_netmask=255.255.255.0 wan0_route= wl_unit=0 wan_bigpond_manual=0 wl0_phytypes=n wan0_pppoe_demand=0 wl0_frag=2346 wl0_wep=disabled wps_button_assertlvl=0 router_disable=0 lan1_proto=dhcp filter_client_sch0= wl_nmode_protection=off wps_sta_pin=00000000 wan0_netmask=255.255.254.0 ddns_username= wl0.4_hwaddr=96:44:52:B9:7E:2F wl0_rifs= wan0_pptp_gateway= pci/1/1/antswctl2g=0 sdram_config=0x184 gs_apMode=0 wan0_wins=127.0.0.1 vlan1ports=4 5* dmz_ipaddr= wl_wds= wl_5G=0 wan_pptp_idletime=5 wps_pinfail=0 wps_ui_dopinpbc=0 cancel_reboot=0 wl0_ampdu_rr_rtylimit_tid=2 2 2 2 2 2 2 2 wl0_rateset=12 pci/1/1/bwduppo=0 wl0.1_ssid=belkin.4e4b.guests wl0_ure= loader_version=0.09e pci/1/1/txchain=3 wl0_wme_apsd=on eco_mode_started=0 sb/1/macaddr=94:44:52:B9:7E:2B wl0_wme_txp_vi=7 3 4 2 0 sb/1/ccode=US wl0_txstreams=0 wl_wme=on pci/1/1/antswitch=0 lan_ifname=br0 wan_primary=0 wl_wme_ap_vi=7 15 1 6016 3008 off off ht_remote_ip=192.168.1.1 wl0_mimo_preamble= boardflags=0x310 wan0_pptp_server_name= wan0_pppoe_mtu=1454 wandevs=vlan1 sdram_refresh=0x1d38 wl0_wme_txp_vo=7 3 4 2 0 sb/1/cck2gpo=0 dhcp_domain=wan wl0.12_hwaddr=96:44:52:B9:7E:27 wl_auth=0 vuze_task_num=0 wps_proc_mac= pci/1/1/pa5gw0a0=0xFEAF sdram_ncdl=0x6e000027 pci/1/1/pa5gw0a1=0xFEC6 sb/1/pa2gw0a0=0xFE98 lan1_domain= wl_wme_ap_vo=3 7 1 3264 1504 off off sb/1/pa2gw0a1=0xFE9E hardware_version=F7D7302 v1 default_wan_macaddr=94:44:52:B9:7E:2C hw_version=0B ezc_enable=1 wl_frameburst=on wl_bss_maxassoc=128 lang_code=0 wl0_nmode_protection=off wan0_lease=43200 pci/1/1/pa5ghw0a0=0xfef3 pci/1/1/pa5ghw0a1=0xFEF3 wan_pppoe_dhcp=dhcp is_modified=0 wan_ipaddr=1.0.0.1 wan_pptp_username= gs_samba_enabled=1 vuze_vod_active=0 wl0_rts=2347 time_zone_DST=1 sb/1/bw40po=0 sb/1/devid=0x4329 lan1_dhcp=0 wan_wins= wl_ifname= check_wifi=1 pci/1/1/leddc=0xffff wl_wep=disabled wl_nbw_cap=1 wl_ampdu_rtylimit_tid=5 5 5 5 5 5 5 5 gs_remote_mgmt_port=8080 wl0_hw_txchain=3 lan_ap_netmask=255.255.255.0 wps_show_status=10 os_version=1.00.23 wl_guest_mode=0 wl_gmode_protection= wan0_pptp_ifname=ppp0 wl0_wpa_gtk_rekey=0 pci/1/1/triso5g=3 wan_pptp_dhcp=dhcp wan_pptp_server_name= wan_bigpond_passwd= wl0_sta_retry_time=5 bt_torrentTimeout=60 wan0_desc=Default Connection wan0_pptp_serviceip= pci/1/1/extpagain5g=2 wl_frag=2346 wl_preauth= wl0_key=1 ses_cl_event=0 filter_macmode=disabled wl_maclist= wps_addER=0 emf_entry= wl_rifs= et0phyaddr=30 console_loglevel=1 dhcp_reserveIP= wl_ure= wl0.5_hwaddr=96:44:52:B9:7E:20 bl_version=1.0.37.01 time_zone=GMT+8 filter_client_key0= wl_bcn_rotate=1 wl_wps_config_state=1 wan0_pppoe_service= wan0_pppoe_idletime=5 wan_ifname=vlan1 wan0_dns_auto=1 wl_wme_sta_be=15 1023 3 0 0 off off wan0_hwaddr=94:44:52:B9:7E:2C sb/1/pdetrange2g=2 wl_radioids= wl0_dfs_postism=60 landevs=vlan2 wl0 wl1 wan_hostname=F7D7302 v1 wl0_radio=0 dhcp1_start=192.168.169.2 wl_corerev= wl_nmcsidx=-1 wl0_nbw_cap=1 wl0.1_wpa_psk= dhcp_reserveRemoveId=0 wl_channel=0 wl0_bcn=100 wps_mode=enabled wl_wme_sta_bk=15 1023 7 0 0 off off wps_currentband= gs_fw_auto=0 gs_usb_enabled=1 wl0_hwaddr=94:44:52:B9:7E:2B wl_radio=0 wl_afterburner=off ddns_timeout= wan0_pptp_passwd= pci/1/1/ccode=0 wl0_ampdu_rtylimit_tid=5 5 5 5 5 5 5 5 wl0_preauth= sb/1/tssipos2g=1 ezc_version=2 emf_enable=1 wl0_gmode_protection= wl0.13_hwaddr=96:44:52:B9:7E:28 wan0_bigpond_user_name= bw_maxRx=100000000 wl0_maclist= bt_torrentExitRatio=0.75 sdram_init=0x0419 wl_rts=2347 log_ram_enable=1 firewall_version=1.3.8 sb/1/antswctl2g=2 lan_wins= wan_pptp_ifname=ppp0 wan_desc= wl_ap_isolate=0 bt_contentFolder=download wps_modelnum=1.00.23 lan_hwnames= wps_method=1 lan1_ifnames=wl0.1 wl0.2 wl0.3 wl1.1 wl1.2 wl1.3 qos1=Voice Device wl_txchain=3 dhcp1_end=192.168.169.100 wl_wme_no_ack=off qos2=Online Games lan_upnp_wfa_subc_num=0 wl0_5G=0 wan0_unit=0 wan0_pppoe_username= remote_auto_fw=0 qos3=Video wl0_wps_config_state=1 wl0_radius_key= qos4=Default wl0_wme_ap_be=15 63 3 0 0 off off wl0_nmcsidx=-1 wl0_corerev=17 wan0_ifnames=vlan1 bw_qos_changed=0 bigpond_started=0 wl_key=1 obscurePSK=1 pci/1/1/regrev=0 wl0_channel=0 wps_aplockdown=0 wl0_wds_timeout=1 pci/1/1/tssipos5g=1 sb/1/ledbh0=0 wps_device_name=Share N300 Wireless N Router eco_wlan_end=48 schedule_reboot_time=255 wl0.1_bss_enabled=0 sb/1/maxp2ga0=0x46 sb/1/ledbh1=0 wl_bridge= wl0_wme_ap_bk=15 1023 7 0 0 off off wl0_wps_mode=enabled pci/1/1/devid=0x432d sb/1/maxp2ga1=0x46 sb/1/ledbh2=0 upnp_enable=1 wl_bss_enabled=0 wan0_pptp_connect_id=0 wan0_pptp_hostname= sb/1/ledbh3=0 wps_config_method=0x84 wl_wme_txp_be=7 3 4 2 0 gs_login_timeout=10 wan_pppoe_ac= gs_remote_mgmt_ip=192.168.2.7 wan0_bigpond_manual=0 pci/1/1/macaddr=00:06:4E:00:00:03 sb/1/cddpo=0 emf_uffp_entry= gs_pingWanBlock=1 eco_wlan_days=0 0 0 0 0 0 0 ddns_status=disabled wps_status=0 wl0_guest_passwd=12345678 lan1_hwaddr=00:00:00:00:00:00 wl_dfs_preism=60 sb/1/rxchain=3 wan_pppoe_ip=0.0.0.0 wl_sta_retry_time=5 wl0_auth_mode=none wl_closed=0 wl_wme_txp_bk=7 3 4 2 0 wl_tpc_db= ac_schedule10=inactive autofw_port0= wl0.6_hwaddr=96:44:52:B9:7E:21 gs_ftp_enabled=0 ac_schedule11=inactive wl0_crypto=aes boardnum=121037G3118844 ac_schedule12=inactive wl0_txchain=3 sb/1/antswitch=0 wan_pppoe_ifname= wan_pptp_passwd= bt_maxDownloads=3 dhcp_reserveMAC= ac_schedule13=inactive wl_bcn=100 ac_schedule14=inactive pci/1/1/maxp5gla0=0x3a wl_reg_mode=off ac_schedule15=inactive pci/1/1/maxp5gla1=0x3a ac_schedule16=inactive ac_schedule17=inactive pci/1/1/antswctl5g=0 ac_schedule18=inactive wl0_guest_timeout=720 wl_antdiv=-1 ac_schedule19=inactive size: 13522 bytes (19246 left)

OpenWrt bootlog

Decompressing...done Decompressing...done Init Arena Init Devs. Boot partition size = 131072(0x20000) et0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.10.128.0 CPU type 0x19740: 453MHz Tot mem: 65536 KBytes CFE mem: 0x80700000 - 0x8079B620 (636448) Data: 0x807326D0 - 0x80734A80 (9136) BSS: 0x80734A80 - 0x80735620 (2976) Heap: 0x80735620 - 0x80799620 (409600) Stack: 0x80799620 - 0x8079B620 (8192) Text: 0x80700000 - 0x807326C4 (206532) Copying boot params..... DONE Bootloader version 0.09e boot_version 0.09e Project name : WG7016F22 1-LF-AK Press space bar to cancel startup... Device eth0: hwaddr 94-44-52-B9-7E-2B, ipaddr 192.168.2.1, mask 255.255.255.0 gateway not set, nameserver not set Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) Loading: .. 3876 bytes read Entry at 0x80001000 Closing network. Starting program at 0x80001000 [ 0.000000] Linux version 3.10.18 (x@gun) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38541) ) #1 Sat Nov 9 20:19:47 PST 2013 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019740 (MIPS 74Kc) [ 0.000000] bcm47xx: using bcma bus [ 0.000000] bcma: bus0: Found chip with id 0x4716, rev 0x01 and package 0x0A [ 0.000000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x1F, class 0x0) [ 0.000000] bcma: bus0: Core 3 found: MIPS 74K (manuf 0x4A7, id 0x82C, rev 0x01, class 0x0) [ 0.000000] bcma: bus0: Early bus registered [ 0.000000] MIPS: machine is Belkin F7D330X [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61492k/65536k available (2402k kernel code, 4044k reserved, 570k data, 220k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] Calibrating delay loop... 225.02 BogoMIPS (lpj=450048) [ 0.040000] pid_max: default: 32768 minimum: 301 [ 0.044000] Mount-cache hash table entries: 512 [ 0.052000] NET: Registered protocol family 16 [ 0.072000] bio: create slab at 0 [ 0.080000] Switching to clocksource MIPS [ 0.092000] NET: Registered protocol family 2 [ 0.100000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.108000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.112000] TCP: Hash tables configured (established 512 bind 512) [ 0.120000] TCP: reno registered [ 0.124000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.132000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.136000] NET: Registered protocol family 1 [ 0.144000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x11, class 0x0) [ 0.152000] bcma: bus0: Core 2 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x00, class 0x0) [ 0.164000] bcma: bus0: Core 4 found: USB 2.0 Host (manuf 0x4BF, id 0x819, rev 0x04, class 0x0) [ 0.172000] bcma: bus0: Core 5 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0E, class 0x0) [ 0.180000] bcma: bus0: Core 6 found: DDR1/DDR2 Memory Controller (manuf 0x4BF, id 0x82E, rev 0x01, class 0x0) [ 0.192000] bcma: bus0: Core 7 found: Internal Memory (manuf 0x4BF, id 0x80E, rev 0x07, class 0x0) [ 0.204000] bcma: bus0: Core 8 found: I2S (manuf 0x4BF, id 0x834, rev 0x00, class 0x0) [ 0.256000] bcma: bus0: PCIEcore in host mode found [ 0.436000] PCI host bridge to bus 0000:00 [ 0.440000] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0bffffff] [ 0.448000] pci_bus 0000:00: root bus resource [io 0x0100-0x07ff] [ 0.452000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.464000] bcma: PCI: Fixing up bridge 0000:00:00.0 [ 0.468000] bcma: PCI: Fixing up device 0000:00:00.0 [ 0.476000] bcma: PCI: Fixing up bridge 0000:00:00.1 [ 0.480000] bcma: PCI: Fixing up device 0000:00:00.1 [ 0.492000] bcma: bus0: Bus registered [ 0.500000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.508000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.520000] msgmni has been set to 120 [ 0.524000] io scheduler noop registered [ 0.528000] io scheduler deadline registered (default) [ 0.532000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled [ 0.564000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 2) is a U6_16550A [ 0.572000] console [ttyS0] enabled, bootconsole disabled [ 0.572000] console [ttyS0] enabled, bootconsole disabled [ 0.588000] physmap platform flash device: 02000001 at 1c000000 [ 0.592000] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0000cb [ 0.604000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.608000] Amd/Fujitsu Extended Query version 1.1. [ 0.616000] number of CFI chips: 1 [ 0.676000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0 [ 0.684000] Creating 6 MTD partitions on "physmap-flash.0": [ 0.688000] 0x000000000000-0x000000030000 : "boot" [ 0.696000] 0x000000030000-0x0000007f0000 : "linux" [ 0.704000] 0x00000003001c-0x0000000309a0 : "loader" [ 0.712000] 0x0000000309a0-0x000000132800 : "kernel" [ 0.720000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.732000] 0x000000132800-0x0000007f0000 : "rootfs" [ 0.740000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.756000] mtd: device 4 (rootfs) set to be root filesystem [ 0.760000] mtd: partition "rootfs_data" created automatically, ofs=0x300000, len=0x4f0000 [ 0.768000] 0x000000300000-0x0000007f0000 : "rootfs_data" [ 0.780000] 0x0000007f0000-0x000000800000 : "nvram" [ 0.792000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds) [ 0.800000] GPIO_WDT: failed to register misc device [ 0.808000] TCP: cubic registered [ 0.808000] NET: Registered protocol family 17 [ 0.816000] 8021q: 802.1Q VLAN Support v1.8 [ 0.828000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.840000] Freeing unused kernel memory: 220K (802e9000 - 80320000) Console is alive procd: Console is alive - watchdog - procd: - watchdog - ^[^[[C^[^[[C[ 3.604000] diag: kernel found a "Belkin F7D330X" [ 3.608000] diag: Detected 'Belkin F7D330X' [ 3.616000] pps_core: LinuxPPS API ver. 1 registered [ 3.620000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 3.632000] PTP clock support registered [ 3.644000] bgmac bcma0:1: Found PHY addr: 30 (NOREGS) [ 3.652000] bgmac bcma0:1: Support for Roboswitch not implemented [ 3.660000] libphy: bgmac mii bus: probed [ 3.740000] b53_common: found switch: BCM5325, rev 0 [ 3.744000] (unregistered net_device): attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=bgmac-0-0:1e) [ 3.760000] bgmac: Broadcom 47xx GBit MAC driver loaded kmod: ran 15 iterations - preinit - procd: - preinit - Press the [f] key and hit [enter] to enter failsafe mode mount_root: jffs2 is ready [ 7.356000] jffs2: notice: (203) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 6 of xref (0 dead, 2 orphan) found. - early - procd: - early - - watchdog - procd: - watchdog - - init - procd: - init - Please press Enter to activate this console. [ 9.344000] NET: Registered protocol family 10 [ 9.364000] nf_conntrack version 0.5.0 (964 buckets, 3856 max) [ 9.380000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 9.408000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5 [ 9.420000] Backport generated by backports.git backports-20130617-4-ge3220f5 [ 9.432000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.500000] xt_time: kernel timezone is -0000 [ 9.532000] cfg80211: Calling CRDA to update world regulatory domain [ 9.540000] cfg80211: World regulatory domain updated: [ 9.544000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 9.552000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.560000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 9.568000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 9.576000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.584000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.672000] PPP generic driver version 2.4.2 [ 9.688000] NET: Registered protocol family 24 [ 9.736000] b43-phy0: Broadcom 4716 WLAN found (core revision 17) [ 9.740000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 5 [ 9.836000] Broadcom 43xx driver loaded [ Features: PNL ] [ 9.852000] Broadcom 43xx-legacy driver loaded [ Features: PLD ] [ 14.560000] device eth0.1 entered promiscuous mode [ 14.568000] device eth0 entered promiscuous mode [ 14.584000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 14.588000] br-lan: port 1(eth0.1) entered forwarding state [ 14.596000] br-lan: port 1(eth0.1) entered forwarding state [ 16.600000] br-lan: port 1(eth0.1) entered forwarding state procd: - init complete -

Notes

Tags

For some Help with the Tags, please have a look here: tags

Back to top

toh/belkin/f7d3302.txt · Last modified: 2013/11/10 10:45 by codyps