User Tools

Site Tools


toh:buffalo:ls421de

Buffalo LinkStation LS421DE

This is a low-cost dual-port SATA NAS box. It comes with a 1GE network port and one USB 2.0 host port one the back and one USB 3.0 on the front.

Supported Versions

Version/Model Launch Date S/N OpenWrt Version Supported Model Specific Notes
LS421DE-EU 2013-05 - pending 1, 2, 3 -

Hardware Highlights

SoC Ram Flash Network USB Serial JTag
Marvell Armada-370@1200Mhz 512MiB 512MiB 1x GigE Yes it's difficult… No

GPL source code available at: http://opensource.buffalo.jp/ls400-110.html

Nas-central thread http://forum.buffalo.nas-central.org/viewtopic.php?f=68&t=30349

Hardware

Info

Instruction set: ARM
Vendor: Marvell Technology Group
Bootloader: U-Boot
System-On-Chip: Marvell Armada-370
CPU @Frq 1x ARM Cortex-A9 @1200MHz
Flash size: 512 MiB (NAND) + 1 MiB (SPI-NOR)
Flash Chip: Hynix H27U4G8F2DTR-BC
RAM size: 512 MiB DDR-3
Ethernet: Marvell NETA Ethernet core
Ethernet phy: Marvell 88E1518 via RGMII-ID
USB: 1x OHCI/EHCI, 1x XHCI
SATA: 2x 3.0 Gbps
Serial: Yes (unpopulated)
JTAG: No

Serial

port.serial general information about the serial port, serial port cable, etc.

The only known way to access the serial console is by wiring up R265 (RX) and R106 (TX) close to the marked edge of the SoC.

Bootlogs

OEM bootlog

BootROM 1.08 Booting from SPI flash DDR3 Training Sequence - Ver 2.3.5 DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED ========================= ==== Welcome to YANAGI == ========================= ** LOADER ** U-Boot 2009.08-svn ( 4月 09 2013 - 19:15:41)Marvell version: 1.1.3 NQ U-Boot Addressing: Code: 00600000:006AFFF0 BSS: 006F8360 Stack: 0x5fff70 PageTable: 0x8e0000 Heap address: 0x900000:0xe00000 BUFFALO_BOOTVER=0.06 Board: Buffalo LS-M 88f6710 SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200Mhz, L2 @ 600Mhz DDR @ 600Mhz, TClock @ 200Mhz DDR 16Bit Width, FastPath Memory Access PEX 0: Root Complex Interface, Detected Link X1 PEX 1: Detected No Link. DRAM: 512 MB CS 0: base 0x00000000 size 512 MB Addresses 14M - 0M are saved for the U-Boot usage. SF: Detected MX25L8006E with page size 256, total 1048576 bytes NAND: 512 MiB u-boot envinit tval=e4cefcd5 FPU not initialized USB 0: Host Mode USB 1: Host Mode Shutting down unused interfaces: AUDIO TDM Modules/Interfaces Detected: SDIO RGMII0 Phy RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) HDD1 Power ON HDD0 Power ON Marvell Serial ATA Adapter Integrated Sata device found Device 0 @ 0 0: Model: WDC WD10EFRX-68FYTN0 Firm: 82.00A82 Ser#: WD-XXXXXXXXXXXX Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Device 1 @ 0 1: Model: WDC WD10EFRX-68PJCN0 Firm: 82.00A82 Ser#: WD-XXXXXXXXXXXX Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) MAC Address : XX:XX:XX:XX:XX:XX MAC Address read from block device 0 : ** Bad partition 1 ** MAC Address read from block device 1 : ** Bad partition 1 ** MMC: MRVL_MMC: 0 Net: egiga0, egiga1 [PRIME] hit any key to switch tftp boot. Hit any key to stop autoboot: 2  1  0 Hit any key to stop autoboot: 3  2  1  0 ### JFFS2 loading '/uImage.buffalo' to 0x1200000 Scanning JFFS2 FS: .  done. ### JFFS2 load complete: 2894408 bytes loaded to 0x1200000 ### JFFS2 loading '/initrd.buffalo' to 0x2600000 ### JFFS2 load complete: 11854685 bytes loaded to 0x2600000 ## Booting kernel from Legacy Image at 01200000 ... Image Name: Linux-3.3.4 Created: 2013-05-29 18:55:47 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2894344 Bytes = 2.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02600000 ... Image Name: initramfs Created: 2013-05-29 19:21:58 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 11854621 Bytes = 11.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0 Initializing cgroup subsys cpu Linux version 3.3.4 (root@debian) (gcc version 4.6.2 (Linaro GCC branch-4.6.2. Marvell GCC 201201-883.01c949de) ) #1 Thu May 30 03:55:41 JST 2013 CPU: Marvell PJ4Bv7 Processor [561f5811] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache Machine: Marvell Armada-370 Using UBoot passing parameters structure >>>>>>>Tag MAC XX:XX:XX:XX:XX:XX >>>>>>>Tag MAC XX:XX:XX:XX:XX:XX Memory policy: ECC disabled, Data cache writealloc Built 1 zonelists in Zone order, mobility grouping off. Total pages: 130048 Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x2600040 panic=5 BOOTVER=0.06 UBOOT_DATE=2013/04/09 mtdparts=armada-nand:0x2000000(boot),0x1e000000(rootfs) nandboot=yes PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 512MB = 512MB total Memory: 498168k/498168k available, 26120k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc053383c (5295 kB) .init : 0xc0534000 - 0xc0559000 ( 148 kB) .data : 0xc055a000 - 0xc0589840 ( 191 kB) .bss : 0xc0589864 - 0xc05c2350 ( 227 kB) NR_IRQS:256 axp_time_init Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok hw perfevents: no hardware support available Setting up static identity map for 0x3da858 - 0x3da89c devtmpfs: initialized xor: measuring software checksum speed arm4regs : 1151.600 MB/sec 8regs : 817.600 MB/sec 32regs : 1149.600 MB/sec xor: using function: arm4regs (1151.600 MB/sec) NET: Registered protocol family 16 L0 cache Enabled Speculative Prefetch Disabled aurora_l2_init Aurora: Enabling L2 AuroraL2: System L2 cache support initialised Support IO coherency. Enable DLB and DRAM write coalescing CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 512MB SDRAM_CS1 ....disable SDRAM_CS2 ....disable SDRAM_CS3 ....disable DEVICE_CS0 ....base f2000000, size 32MB DEVICE_CS1 ....no such DEVICE_CS2 ....no such DEVICE_CS3 ....no such PEX0_MEM ....base e0000000, size 32MB PEX0_IO ....base f1100000, size 1MB PEX1_MEM ....base e2000000, size 32MB PEX1_IO ....base f1200000, size 1MB INTER_REGS ....base d0000000, size 1MB DMA_UART ....no such SPI_CS0 ....base f0000000, size 16MB SPI_CS1 ....no such SPI_CS2 ....no such SPI_CS3 ....no such SPI_CS4 ....no such SPI_CS5 ....no such SPI_CS6 ....no such SPI_CS7 ....no such BOOT_ROM_CS ....no such DEV_BOOTCS ....base f5000000, size 16MB PMU_SCRATCHPAD ....no such CRYPT0_ENG ....base c8010000, size 64KB Marvell Armada370 Board-- YANAGI Soc: MV6710 A1 LE LSP version: Armada370_LSP_3.1.0_p15_NQ Detected Tclk 200000000, SysClk 600000000, FabricClk 600000000 gpiochip_add: registered GPIOs 0 to 64 on device: mv_gpio hw-breakpoint: debug architecture 0x4 unsupported. Marvell USB EHCI Host controller #0: d004c400 Marvell USB EHCI Host controller #1: d004c200 PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe1ffffff] PCI: bus0: Fast back to back transfers disabled PCI host bridge to bus 0000:01 pci_bus 0000:01: root bus resource [io 0x100000-0x1fffff] pci_bus 0000:01: root bus resource [mem 0xe2000000-0xe3ffffff] PCI: bus1: Fast back to back transfers enabled pci 0000:00:01.0: BAR 0: assigned [mem 0xe0000000-0xe0001fff 64bit] bio: create slab <bio-0> at 0 raid6: int32x1 135 MB/s raid6: int32x2 210 MB/s raid6: int32x4 203 MB/s raid6: int32x8 244 MB/s raid6: using algorithm int32x8 (244 MB/s) vgaarb: loaded SCSI subsystem initialized Switching to clocksource armada370_clocksource NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Trying to unpack rootfs image as initramfs... Freeing initrd memory: 11576K cesadev_init(c053bb7c) mvCesaInit: channels=1, session=640, queue=64 Armada XP hwmon thermal sensor initialized. Initializing Armada-XP CPU power management (DISABLED) MICON ctrl (C) BUFFALO INC. V.1.00 installed. Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.1.00 installed. Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed. Kernel event proc (C) BUFFALO INC. V.1.00 installed. initial_polarity_val = 0x0001f800 initial_polarity_val_high = 0x00000000 Buffalo GPIO SATA Hotplug Event Driver (C) BUFFALO INC. Ver.1.00 installed. VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. fuse init (API version 7.18) SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled SGI XFS Quota Management subsystem msgmni has been set to 995 async_tx: api initialized (async) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Initializing ths8200_init Initializing dove_adi9889_init mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver mv_xor mv_xor.0: Marvell XOR: ( xor ) mv_xor mv_xor.1: Marvell XOR: ( xor ) mv_xor mv_xor.2: Marvell XOR: ( cpy ) mv_xor mv_xor.3: Marvell XOR: ( fill cpy ) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xd0012000 (irq = 41) is a 16550A console [ttyS0] enabled brd: module loaded loop: module loaded ** BUFFALO Disable Command Queuing Function [sata_mv sata_mv.0] ** sata_mv sata_mv.0: slots 32 ports 2 scsi0 : sata_mv scsi1 : sata_mv ata1: SATA max UDMA/133 irq 55 ata2: SATA max UDMA/133 irq 55 SPI Serial flash detected @ 0xf0000000, 1024KB (16sec x 64KB) armada-nand armada-nand.0: Initialize HAL based NFC in 8bit mode with DMA Disabled using BCH 4bit ECC NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit) Bad block table found at page 262080, version 0x01 Bad block table found at page 262016, version 0x01 nand_read_bbt: bad block at 0x000002f20000 nand_read_bbt: bad block at 0x000006120000 nand_read_bbt: bad block at 0x000009da0000 nand_read_bbt: bad block at 0x00000fbe0000 nand_read_bbt: bad block at 0x000016280000 2 cmdlinepart partitions found on MTD device armada-nand Creating 2 MTD partitions on "armada-nand": 0x000000000000-0x000002000000 : "boot" 0x000002000000-0x000020000000 : "rootfs" mv_eth_probe: port_mask=0x3, cpu_mask=0x1 0 - Base 0x00000000 , Size = 0x20000000. 4 - Base 0xf2000000 , Size = 0x02000000. 8 - Base 0xe0000000 , Size = 0x02000000. 9 - Base 0xf1100000 , Size = 0x00100000. 10 - Base 0xe2000000 , Size = 0x02000000. 11 - Base 0xf1200000 , Size = 0x00100000. 12 - Base 0xd0000000 , Size = 0x00100000. 14 - Base 0xf0000000 , Size = 0x01000000. 23 - Base 0xf5000000 , Size = 0x01000000. 25 - Base 0xc8010000 , Size = 0x00010000. o 2 Giga ports supported o NETA acceleration mode 1 o RX Queue support: 1 Queues * 128 Descriptors o TX Queue support: 1 Queues * 512 Descriptors o GSO supported o GRO supported o Receive checksum offload supported o Transmit checksum offload supported o Driver ERROR statistics enabled o Switch support enabled o Loading network interface(s) o Port 0 is connected to Linux netdevice giga p=0: mtu=1500, mac=d002beec o eth0, ifindex = 2, GbE port = 0 o Port 1 is connected to Linux netdevice giga p=1: mtu=1500, mac=d002beec o eth1, ifindex = 3, GbE port = 1 sky2: driver version 1.30 i2c /dev entries driver rtc-rs5c372 0-0032: clock needs to be set rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6 rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0 md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 cpuidle: using governor ladder cpuidle: using governor menu mmc0: mvsdio driver initialized, lacking card detect (fall back to polling) TCP cubic registered NET: Registered protocol family 17 VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 rtc-rs5c372 0-0032: hctosys: unable to read the hardware clock ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata1.00: ATA-9: WDC WD10EFRX-68FYTN0, 82.00A82, max UDMA/133 ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD10EFRX-68F 82.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 0:0:0:0: [sda] 4096-byte physical blocks sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: unknown partition table sd 0:0:0:0: [sda] Attached SCSI disk ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) ata2.00: ATA-9: WDC WD10EFRX-68PJCN0, 82.00A82, max UDMA/133 ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD10EFRX-68P 82.0 PQ: 0 ANSI: 5 sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 1:0:0:0: [sdb] 4096-byte physical blocks sd 1:0:0:0: [sdb] Write Protect is off sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: unknown partition table sd 1:0:0:0: [sdb] Attached SCSI disk Freeing init memory: 148K ---- in /init --- mount: mounting shm on /dev/shm failed: No such file or directory mount: mounting devpts on /dev/pts failed: No such file or directory ldconfig: /usr/lib/libstdc++.so.6.0.16-gdb.py is not an ELF file - it has the wrong magic bytes at the start. err: libsys: nas_feature : using /root/.nas_features/EU/0x0000300C Checking the existance of micon ... LS-WSGL/R1Ver1.0 libsys: /etc/sysctl.conf : using /root/.params/sysctl/0x0000300C cp: can't stat '/root/.params/sysctl/0x0000300C.iSCSI': No such file or directory ls: /dev/rtc: No such file or directory libsys: /dev/rtc was updated : /dev/rtc 254 0 hwclock: ioctl(RTC_RD_TIME) to /dev/rtc to read the time failed: Invalid argument Thu Nov 1 00:00:00 JST 2007 hwclock: ioctl(RTC_RD_TIME) to /dev/rtc to read the time failed: Invalid argument Thu Nov 1 00:00:00 JST 2007 *** Caution!!! /etc/fanctld.conf create failed! ldconfig: /usr/lib/libstdc++.so.6.0.16-gdb.py is not an ELF file - it has the wrong magic bytes at the start. modprobe: module e1000e not found in modules.dep LibSys_GetUsbDiskStartNum : Usb device not found(/sys/block/sdc/device). Returning 3 grep: /var/tmp/devlink: No such file or directory create_devlink:Using new routine. linuxrc:choose operation (timeout 4[s]) 1:RamRoot 2:sda1 2:sda2 other:HddRoot ? -HddRoot- -- rebuild mdadm.conf for BOOT, ROOTFS with Intelligent routine -- checkDiskStatus : disk1 plugged checkDiskStatus : disk1 LibSys_IsScsiDeviceExist [1] 0:0:0:0 checkDiskStatus : disk2 plugged checkDiskStatus : disk2 LibSys_IsScsiDeviceExist [1] 1:0:0:0 checkDiskStatus : disk1 plugged checkDiskPeformance : disk1 performans test ... 152117 kB/s [OK] checkDiskStatus : disk2 plugged checkDiskPeformance : disk2 performans test ... 148686 kB/s [OK] mount: mounting /dev/disk1_1 on /tmp/boot_test failed: No such file or directory mount: mounting /dev/disk2_1 on /tmp/boot_test failed: No such file or directory libmd: GetMdBaseDisk : Selected 0 mdadm: cannot open /dev/disk?_1: No such file or directory mdadm: cannot open /dev/disk??_1: No such file or directory mdadm: cannot open /dev/disk?_2: No such file or directory mdadm: cannot open /dev/disk??_2: No such file or directory mdadm: cannot open /dev/disk?_5: No such file or directory mdadm: cannot open /dev/disk??_5: No such file or directory mdadm: No devices listed in conf file were found. -- setup max error counts -- /sys/block/md0/md/maxerr_cnt is setted to -1 /usr/local/lib/libmd: line 765: /sys/block/md0/md/maxerr_cnt: No such file or directory /sys/block/md1/md/maxerr_cnt is setted to -1 /usr/local/lib/libmd: line 765: /sys/block/md1/md/maxerr_cnt: No such file or directory /sys/block/md2/md/maxerr_cnt is setted to -1 /usr/local/lib/libmd: line 765: /sys/block/md2/md/maxerr_cnt: No such file or directory /usr/local/bin/hdd_raid_syncspeed.sh: line 148: /sys/block/md0/md/sync_speed_max: No such file or directory /usr/local/bin/hdd_raid_syncspeed.sh: line 148: /sys/block/md1/md/sync_speed_max: No such file or directory /usr/local/bin/hdd_raid_syncspeed.sh: line 148: /sys/block/md2/md/sync_speed_max: No such file or directory Starting :fsck_disks(boot) ... [Failed. ] Starting :mount(boot) ... [Failed. ] mount: mounting /dev/md1 on /rootfs failed: No such file or directory mount: mounting /dev/md1 on /rootfs failed: No such file or directory TestRootfs failed -RamdiskRoot- --- rcStart (initrd) --- mount: mounting proc on /proc failed: Device or resource busy mount: mounting sysfs on /sys failed: Device or resource busy ldconfig: /usr/lib/libstdc++.so.6.0.16-gdb.py is not an ELF file - it has the wrong magic bytes at the start. Cannot set device ring parameters: Operation not supported Cannot set device ring parameters: Operation not supported Cannot set device ring parameters: Operation not supported Cannot set device ring parameters: Operation not supported Cannot get device ring settings: No such device Cannot get device ring settings: No such device Cannot get device ring settings: No such device Cannot get device ring settings: No such device modprobe: module e1000e not found in modules.dep === checkroot.sh === grep: /var/tmp/devlink: No such file or directory create_devlink:Using new routine. swapon: can't stat '/dev/md2': No such file or directory create dir : /var/www === create_devlink.sh === create_devlink:Using new routine. === startSysMd.sh === -- rebuild mdadm.conf for BOOT, ROOTFS with Intelligent routine -- checkDiskStatus : disk1 plugged checkDiskStatus : disk1 LibSys_IsScsiDeviceExist [1] 0:0:0:0 checkDiskStatus : disk2 plugged checkDiskStatus : disk2 LibSys_IsScsiDeviceExist [1] 1:0:0:0 checkDiskStatus : disk1 plugged checkDiskPeformance : disk1 performans test ... 152110 kB/s [OK] checkDiskStatus : disk2 plugged checkDiskPeformance : disk2 performans test ... 149027 kB/s [OK] mount: mounting /dev/disk1_1 on /tmp/boot_test failed: No such file or directory mount: mounting /dev/disk2_1 on /tmp/boot_test failed: No such file or directory libmd: GetMdBaseDisk : Selected 0 mdadm: cannot open /dev/disk?_1: No such file or directory mdadm: cannot open /dev/disk??_1: No such file or directory mdadm: cannot open /dev/disk?_2: No such file or directory mdadm: cannot open /dev/disk??_2: No such file or directory mdadm: cannot open /dev/disk?_5: No such file or directory mdadm: cannot open /dev/disk??_5: No such file or directory mdadm: No devices listed in conf file were found. -- setup max error counts -- /sys/block/md0/md/maxerr_cnt is setted to -1 /usr/local/lib/libmd: line 765: /sys/block/md0/md/maxerr_cnt: No such file or directory /sys/block/md1/md/maxerr_cnt is setted to -1 /usr/local/lib/libmd: line 765: /sys/block/md1/md/maxerr_cnt: No such file or directory /sys/block/md2/md/maxerr_cnt is setted to -1 /usr/local/lib/libmd: line 765: /sys/block/md2/md/maxerr_cnt: No such file or directory /usr/local/bin/hdd_raid_syncspeed.sh: line 148: /sys/block/md0/md/sync_speed_max: No such file or directory /usr/local/bin/hdd_raid_syncspeed.sh: line 148: /sys/block/md1/md/sync_speed_max: No such file or directory /usr/local/bin/hdd_raid_syncspeed.sh: line 148: /sys/block/md2/md/sync_speed_max: No such file or directory === fwupdate.sh === umount: can't umount /boot: Invalid argument mkdir: can't create directory '/boot': File exists mount: mounting /dev/md0 on /boot failed: No such file or directory === check_nandboot.sh === grep: /tmp/check_nandboot: No such file or directory === acpid.sh === /etc/init.d/rcS: line 43: /etc/init.d/acpid.sh: No such file or directory === closeSysMd.sh === mdadm: error opening /dev/md0: No such file or directory mdadm: error opening /dev/md1: No such file or directory mdadm: error opening /dev/md2: No such file or directory === sethostname.sh === configure files from Buffalo parameters. === restore_config.sh === -- rebuild mdadm.conf for BOOT -- mdadm: cannot open /dev/disk?_1: No such file or directory mdadm: cannot open /dev/disk??_1: No such file or directory mdadm: No devices listed in conf file were found. -- setup max error counts -- /sys/block/md0/md/maxerr_cnt is setted to -1 /usr/local/lib/libmd: line 765: /sys/block/md0/md/maxerr_cnt: No such file or directory mount: mounting /dev/md0 on /boot failed: No such file or directory Restore previous configuration files tar (child): /boot/conf_save.tgz: Cannot open: No such file or directory tar (child): Error is not recoverable: exiting now tar (child): /boot/conf_save.tgz: Cannot open: No such file or directory tar (child): Error is not recoverable: exiting now /bin/tar: Child returned status 2 /bin/tar: Error is not recoverable: exiting now /bin/tar: Child returned status 2 /bin/tar: Error is not recoverable: exiting now unzip fail. /tmp/etc/localtime -> BusyBox v1.19.4 (2013-05-13 21:53:16 JST) multi-call binary. Usage: dirname FILENAME Strip non-directory suffix from FILENAME BusyBox v1.19.4 (2013-05-13 21:53:16 JST) multi-call binary. Usage: mkdir [OPTIONS] DIRECTORY... Create DIRECTORY -m MODE Mode -p No error if exists; make parent directories as needed umount: can't umount /boot: Invalid argument rootfs on / type rootfs (rw,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,relatime) sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,relatime) udev on /dev type devtmpfs (rw,nosuid,relatime,size=10240k,nr_inodes=62271,mode=755) /dev/ram1 on /mnt/ram type tmpfs (rw,relatime,size=15360k) PID USER COMMAND 1 root init 2 root [kthreadd] 3 root [ksoftirqd/0] 4 root [kworker/0:0] 5 root [kworker/u:0] 6 root [khelper] 7 root [kdevtmpfs] 8 root [kworker/u:1] 142 root [sync_supers] 144 root [bdi-default] 146 root [kblockd] 153 root [ata_sff] 159 root [md] 179 root [rpciod] 180 root [kworker/0:1] 183 root [crypto] 184 root [crypto_ret] 197 root [kswapd0] 198 root [fsnotify_mark] 199 root [nfsiod] 201 root [xfs_mru_cache] 202 root [xfslogd] 203 root [xfsdatad] 204 root [xfsconvertd] 205 root [crypto] 317 root [scsi_eh_0] 320 root [scsi_eh_1] 323 root [kworker/u:2] 324 root [kworker/u:3] 335 root [mtdblock0] 341 root [mtdblock1] 346 root [mtdblock2] 369 root [kworker/u:4] 754 root {rcS} /bin/sh /etc/init.d/rcS 1325 root {restore_config.} /bin/sh /etc/init.d/restore_config.sh start 1353 root ps mdadm: error opening /dev/md0: No such file or directory mdadm: error opening /dev/md1: No such file or directory mdadm: error opening /dev/md2: No such file or directory grep: /etc/melco/iscsi_info: No such file or directory /etc/init.d/restore_config.sh: line 59: perl: command not found === EnablingAutoip.sh === === networking.sh === /etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-eth0.pid eth0 /etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-eth1.pid eth1 /etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-bond0.pid bond0 /etc/init.d/networking.sh : Read dhcpc file /etc/init.d/networking.sh : configure : create network files.. (eth0) IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[] create network files.. (eth1) IP=[dhcp], netmask=[], dgw=[] dhcpcd: no process found /etc/init.d/networking.sh : Delete /etc/dhcpc/dhcpcd-.pid Configuration network interface: lo eth0 eth1 /sbin/ifconfig eth0 mtu 1500 multicast /sbin/ifconfig eth1 mtu 1500 multicast requesting DHCP tout=30[s] networking.sh: dhcp requesting... DontDownIfacepool #1: pkt_size=1536, buf_size=1632 - 256 of 256 buffers added alwaysFork eth1: link up eth1: link up, full duplex, speed 1 Gbps eth1: started SIOCGIFADDR :Cannot assign requested address sendto: count 6 sync 0 sendto: count 6 sync 0 dhcpcd.exe: interface eth1 has been configured with new IP=X.X.X.X GATEWAY=X.X.X.X ** eth1 : networking.sh dhcp fin. /sbin/ifconfig eth0 netmask Waiting 1421 ...finished. Checking network address for each network device SIOCGIFADDR :No such device networking.sh: arp_newip_notify_sub : Can't get ipaddr of eth0. networking.sh: arp_newip_notify_sub : executing arping -A X.X.X.X -I eth1 -c 1 configure files from Buffalo parameters. === syslog.sh === Starting system logger: load_info ItemValue = off LoadConfFileStringEx:key=[ad_dns] not found in /etc/melco/info. LoadConfFileOnOffEx:key=[info_visible] not found in /etc/melco/info. LoadConfFileOnOffEx:key=[smb2] not found in /etc/melco/info. Starting kernel logger: === kernelmon.sh === Starting kernelmon:=== fanctld.sh === * Starting fanctld ... [ ok ] === usb.sh === usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb xhci_hcd 0000:00:01.0: xHCI Host Controller xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 1 xhci_hcd 0000:00:01.0: irq 58, io mem 0xe0000000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhci_hcd 0000:00:01.0: xHCI Host Controller xhci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci_marvell ehci_marvell.0: Marvell Orion EHCI ehci_marvell ehci_marvell.0: new USB bus registered, assigned bus number 3 ehci_marvell ehci_marvell.0: irq 45, io base 0xfbb50100 ehci_marvell ehci_marvell.0: USB 2.0 started, EHCI 1.00 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected ehci_marvell ehci_marvell.1: Marvell Orion EHCI ehci_marvell ehci_marvell.1: new USB bus registered, assigned bus number 4 ehci_marvell ehci_marvell.1: irq 46, io base 0xfbb51100 ehci_marvell ehci_marvell.1: USB 2.0 started, EHCI 1.00 hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usblp grep: /etc/melco/usbshareinfo: No such file or directory /usr/local/lib/libsys: line 1078: sqlite3: command not found grep: /etc/melco/usbshareinfo: No such file or directory /usr/local/lib/libsys: line 1078: sqlite3: command not found KERNELMOn (SATA 0 plugged) /usr/local/lib/libsys: line 1103: sqlite3: command not found /usr/local/lib/libsys: line 1103: sqlite3: command not found /usr/local/lib/libsys: line 1115: sqlite3: command not found /usr/local/lib/libsys: line 1115: sqlite3: command not found === clientUtil_servd.sh === Starting clientUtil_server: ->Starting on eth1 ->Starting on eth0 === daemonwatch.sh === Starting daemonwatch:daemonwatch Ver.1.01 watch list file : /etc/daemonwatch.list === bootcomplete.sh === No need to run drivecheck.sh KERNELMOn (SATA 1 plugged) /usr/local/bin/hdd_raid_syncspeed.sh: line 148: /sys/block/md0/md/sync_speed_max: No such file or directory /usr/local/bin/hdd_raid_syncspeed.sh: line 148: /sys/block/md1/md/sync_speed_max: No such file or directory /usr/local/bin/hdd_raid_syncspeed.sh: line 148: /sys/block/md2/md/sync_speed_max: No such file or directory hdd_raid_syncspeed.sh: Adding EDP md devices hdd_raid_syncspeed.sh: USERLAND_MD=md10 md11 md12 md13 md14 md101 md102 === micon_setup.sh === === late_inspection_phase.sh === KERNELMOn (lanact 1000 full eth1) === buffalo_rescue.sh === buffalo_rescue.sh: Its not a usb boot environment. **** request DHCP eth1 BUFFALO INC. LinkStation series LS421DE-EM986 login: **** release DHCP IP eth1: stopped eth1: link up eth1: started ** eth1 : networking.sh dhcp fin. Checking network address for each network device Checking network address for each network device KERNELMOn (PSW_on) OF admin Password: admin@LS421DE-EM986:~$ netstat -l Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State netstat: /proc/net/tcp6: No such file or directory udp 0 0 0.0.0.0:bootpc 0.0.0.0:* udp 0 0 0.0.0.0:22936 0.0.0.0:* udp 0 0 0.0.0.0:22936 0.0.0.0:* netstat: /proc/net/udp6: No such file or directory netstat: /proc/net/raw6: No such file or directory Active UNIX domain sockets (only servers) Proto RefCnt Flags Type State I-Node Path


OpenWrt bootlog

BootROM 1.08 Booting from SPI flash DDR3 Training Sequence - Ver 2.3.5 DDR3 Training Sequence - Ended Successfully BootROM: Image checksum verification PASSED ========================= ==== Welcome to YANAGI == ========================= ** LOADER ** U-Boot 2009.08-svn ( 4月 09 2013 - 19:15:41)Marvell version: 1.1.3 NQ U-Boot Addressing: Code: 00600000:006AFFF0 BSS: 006F8360 Stack: 0x5fff70 PageTable: 0x8e0000 Heap address: 0x900000:0xe00000 BUFFALO_BOOTVER=0.06 Board: Buffalo LS-M 88f6710 SoC: MV6710 A1 CPU: Marvell PJ4B v7 UP (Rev 1) LE CPU @ 1200Mhz, L2 @ 600Mhz DDR @ 600Mhz, TClock @ 200Mhz DDR 16Bit Width, FastPath Memory Access PEX 0: Root Complex Interface, Detected Link X1 PEX 1: Detected No Link. DRAM: 512 MB CS 0: base 0x00000000 size 512 MB Addresses 14M - 0M are saved for the U-Boot usage. SF: Detected MX25L8006E with page size 256, total 1048576 bytes NAND: 512 MiB u-boot envinit tval=e4cef545 FPU not initialized USB 0: Host Mode USB 1: Host Mode Shutting down unused interfaces: AUDIO TDM Modules/Interfaces Detected: SDIO RGMII0 Phy RGMII1 Phy PEX0 (Lane 0) PEX1 (Lane 1) SATA0 (Lane 2) SATA1 (Lane 3) HDD1 Power ON HDD0 Power ON Marvell Serial ATA Adapter Integrated Sata device found Device 0 @ 0 0: Model: WDC WD10EFRX-68FYTN0 Firm: 82.00A82 Ser#: WD-WCC4J6RN7E4X Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) Device 1 @ 0 1: Model: WDC WD10EFRX-68PJCN0 Firm: 82.00A82 Ser#: WD-WCC4JLLJ5R7P Type: Hard Disk Supports 48-bit addressing Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) MAC Address : 10:6F:3F:CD:19:86 MAC Address read from block device 0 : ** Bad partition 1 ** MAC Address read from block device 1 : ** Bad partition 1 ** MMC: MRVL_MMC: 0 Net: egiga0, egiga1 [PRIME] hit any key to switch tftp boot. Hit any key to stop autoboot: 2  0 switched to TFTP boot. Hit any key to stop autoboot: 3  2  1  0 Using egiga1 device TFTP from server 192.168.11.1; our IP address is 192.168.11.150 Filename 'uImage.buffalo'. Load address: 0x1200000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########## done Bytes transferred = 5870520 (5993b8 hex) Using egiga1 device TFTP from server 192.168.11.1; our IP address is 192.168.11.150 Filename 'initrd.buffalo'. Load address: 0x2600000 Loading: * TFTP error: 'File not found' (1) Starting again ## Booting kernel from Legacy Image at 01200000 ... Image Name: ARM OpenWrt Linux-4.0.8 Created: 2015-07-14 20:37:49 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5870456 Bytes = 5.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Wrong Ramdisk Image Format Ramdisk image is corrupt or invalid Hit any key to stop autoboot: 3  2  0 BUFFALO>> bootm 1200000 ## Booting kernel from Legacy Image at 01200000 ... Image Name: ARM OpenWrt Linux-4.0.8 Created: 2015-07-14 20:37:49 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5870456 Bytes = 5.6 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.0.8 (daniel@box) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r46113) ) #23 SMP Tue Jul 14 22:37:31 CEST 2015 [ 0.000000] CPU: ARMv7 Processor [561f5811] revision 1 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine model: BUFFALO LS42x [ 0.000000] Memory policy: Data cache writeback [ 0.000000] CPU: All CPU(s) started in SVC mode. [ 0.000000] PERCPU: Embedded 9 pages/cpu @dfbe1000 s7104 r8192 d21568 u36864 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048 [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x2600040 panic=5 BOOTVER=0.06 UBOOT_DATE=2013/04/09 mtdparts=armada-nand:0x2000000(boot),0x1e000000(rootfs) tftpboot=yes [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 510920K/524288K available (3170K kernel code, 136K rwdata, 872K rodata, 4388K init, 157K bss, 13368K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc03fae5c (4044 kB) [ 0.000000] .init : 0xc03fb000 - 0xc0844000 (4388 kB) [ 0.000000] .data : 0xc0844000 - 0xc08663c8 ( 137 kB) [ 0.000000] .bss : 0xc08663c8 - 0xc088d8fc ( 158 kB) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1. [ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] L2C: DT/platform modifies aux control register: 0x12086300 -> 0x1a086302 [ 0.000000] Aurora cache controller enabled, 4 ways, 256 kB [ 0.000000] Aurora: CACHE_ID 0x00000100, AUX_CTRL 0x1a086302 [ 0.000013] sched_clock: 32 bits at 18MHz, resolution 53ns, wraps every 229064922058ns [ 0.000249] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256) [ 0.090097] pid_max: default: 32768 minimum: 301 [ 0.090183] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090193] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.090565] CPU: Testing write buffer coherency: ok [ 0.090753] CPU0: thread -1, cpu 0, socket -1, mpidr 0 [ 0.090813] Setting up static identity map for 0x12508 - 0x12560 [ 0.091151] mvebu-soc-id: MVEBU SoC ID=0x6710, Rev=0x1 [ 0.091287] mvebu-pmsu: Initializing Power Management Service Unit [ 0.091914] Brought up 1 CPUs [ 0.091925] SMP: Total of 1 processors activated (1196.85 BogoMIPS). [ 0.091932] CPU: All CPU(s) started in SVC mode. [ 0.092448] VFP support v0.3: implementor 56 architecture 2 part 20 variant 9 rev 6 [ 0.092643] pinctrl core: initialized pinctrl subsystem [ 0.096223] NET: Registered protocol family 16 [ 0.096543] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.096912] cpuidle: using governor ladder [ 0.108454] platform soc:regulators:ata1-regulator: Driver reg-fixed-voltage requests probe deferral [ 0.108513] platform soc:regulators:ata2-regulator: Driver reg-fixed-voltage requests probe deferral [ 0.108562] platform soc:regulators:usb-v5-regulator: Driver reg-fixed-voltage requests probe deferral [ 0.109709] Switched to clocksource armada_370_xp_clocksource [ 0.110551] NET: Registered protocol family 2 [ 0.111058] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.111090] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 0.111132] TCP: Hash tables configured (established 4096 bind 4096) [ 0.111178] TCP: reno registered [ 0.111188] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.111202] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.111321] NET: Registered protocol family 1 [ 1.619510] futex hash table entries: 256 (order: 2, 16384 bytes) [ 1.620491] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.620509] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 1.621023] io scheduler noop registered [ 1.621038] io scheduler deadline registered (default) [ 1.621636] armada-370-pinctrl d0018000.pin-ctrl: registered pinctrl driver [ 1.622337] irq: Cannot allocate irq_descs @ IRQ38, assuming pre-allocated [ 1.622720] irq: Cannot allocate irq_descs @ IRQ70, assuming pre-allocated [ 1.622978] irq: Cannot allocate irq_descs @ IRQ102, assuming pre-allocated [ 1.623375] mvebu-pcie soc:pcie-controller: PCI host bridge to bus 0000:00 [ 1.623391] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff] [ 1.623402] pci_bus 0000:00: root bus resource [mem 0xf8000000-0xffdfffff] [ 1.623412] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.623610] PCI: bus0: Fast back to back transfers disabled [ 1.623622] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.624152] PCI: bus1: Fast back to back transfers disabled [ 1.624239] pci 0000:00:01.0: BAR 8: assigned [mem 0xf8000000-0xf80fffff] [ 1.624254] pci 0000:01:00.0: BAR 0: assigned [mem 0xf8000000-0xf8001fff 64bit] [ 1.624281] pci 0000:00:01.0: PCI bridge to [bus 01] [ 1.624294] pci 0000:00:01.0: bridge window [mem 0xf8000000-0xf80fffff] [ 1.624334] pci 0000:00:01.0: enabling device (0140 -> 0142) [ 1.624515] mv_xor d0060800.xor: Marvell shared XOR driver [ 1.659502] mv_xor d0060800.xor: Marvell XOR: ( xor cpy ) [ 1.699487] mv_xor d0060800.xor: Marvell XOR: ( xor cpy ) [ 1.699618] mv_xor d0060900.xor: Marvell shared XOR driver [ 1.739488] mv_xor d0060900.xor: Marvell XOR: ( xor cpy ) [ 1.779487] mv_xor d0060900.xor: Marvell XOR: ( xor cpy ) [ 1.779710] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.780254] console [ttyS0] disabled [ 1.800332] d0012000.serial: ttyS0 at MMIO 0xd0012000 (irq = 19, base_baud = 12500000) is a 16550A [ 2.380359] console [ttyS0] enabled [ 2.384483] pxa3xx-nand d00d0000.nand: This platform can't do DMA on this device [ 2.392944] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc [ 2.399334] nand: Hynix H27U4G8F2DTR-BC [ 2.403223] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.410847] pxa3xx-nand d00d0000.nand: ECC strength 16, ECC step size 2048 [ 2.417997] Bad block table found at page 262080, version 0x01 [ 2.424203] Bad block table found at page 262016, version 0x01 [ 2.430271] nand_read_bbt: bad block at 0x000002f20000 [ 2.435440] nand_read_bbt: bad block at 0x000006120000 [ 2.440624] nand_read_bbt: bad block at 0x000009da0000 [ 2.445794] nand_read_bbt: bad block at 0x00000fbe0000 [ 2.450975] nand_read_bbt: bad block at 0x000016280000 [ 2.456366] 2 ofpart partitions found on MTD device pxa3xx_nand-0 [ 2.462522] Creating 2 MTD partitions on "pxa3xx_nand-0": [ 2.467951] 0x000000000000-0x000002000000 : "boot" [ 2.473387] 0x000002000000-0x000020000000 : "rootfs" [ 2.479630] mtd: device 1 (rootfs) set to be root filesystem [ 2.485881] mtdsplit: no squashfs found in "rootfs" [ 2.490831] mtdsplit: no squashfs found in "pxa3xx_nand-0" [ 2.497234] m25p80 spi0.0: mx25l8005 (1024 Kbytes) [ 2.502328] 2 ofpart partitions found on MTD device spi0.0 [ 2.507842] Creating 2 MTD partitions on "spi0.0": [ 2.512697] 0x000000000000-0x0000000f0000 : "u-boot" [ 2.518261] 0x0000000f0000-0x000000100000 : "u-boot-env" [ 2.524725] libphy: Fixed MDIO Bus: probed [ 2.529039] libphy: orion_mdio_bus: probed [ 2.536124] mvneta d0074000.ethernet eth0: Using hardware mac address 10:6f:3f:cd:19:86 [ 2.545737] TCP: cubic registered [ 2.549079] NET: Registered protocol family 17 [ 2.553623] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 2.566306] 8021q: 802.1Q VLAN Support v1.8 [ 2.570599] Registering SWP/SWPB emulation handler [ 12.600124] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 12.611181] Freeing unused kernel memory: 4388K (c03fb000 - c0844000) [ 12.629289] init: Console is alive [ 12.650522] usbcore: registered new interface driver usbfs [ 12.656111] usbcore: registered new interface driver hub [ 12.661598] usbcore: registered new device driver usb [ 12.669788] Button Hotplug driver version 0.4.1 [ 12.688508] SCSI subsystem initialized [ 12.695847] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.703553] ehci-platform: EHCI generic platform driver [ 12.709970] ehci-orion: EHCI orion driver [ 12.714204] orion-ehci d0050000.usb: EHCI Host Controller [ 12.719759] orion-ehci d0050000.usb: new USB bus registered, assigned bus number 1 [ 12.727494] orion-ehci d0050000.usb: irq 25, io mem 0xd0050000 [ 12.749624] orion-ehci d0050000.usb: USB 2.0 started, EHCI 1.00 [ 12.756447] hub 1-0:1.0: USB hub found [ 12.760672] hub 1-0:1.0: 1 port detected [ 12.772454] sata_mv d00a0000.sata: slots 32 ports 2 [ 12.779864] scsi host0: sata_mv [ 12.783830] scsi host1: sata_mv [ 12.787247] ata1: SATA max UDMA/133 irq 27 [ 12.791472] ata2: SATA max UDMA/133 irq 27 [ 13.299608] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 13.319878] ata1.00: ATA-9: WDC WD10EFRX-68FYTN0, 82.00A82, max UDMA/133 [ 13.326627] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 13.349888] ata1.00: configured for UDMA/133 [ 13.354602] scsi 0:0:0:0: Direct-Access ATA WDC WD10EFRX-68F 0A82 PQ: 0 ANSI: 5 [ 13.364194] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 13.371955] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 13.377989] sd 0:0:0:0: [sda] Write Protect is off [ 13.383156] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 13.398334] sd 0:0:0:0: [sda] Attached SCSI disk [ 13.869608] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300) [ 13.889870] ata2.00: ATA-9: WDC WD10EFRX-68PJCN0, 82.00A82, max UDMA/133 [ 13.896617] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 13.919879] ata2.00: configured for UDMA/133 [ 13.924581] scsi 1:0:0:0: Direct-Access ATA WDC WD10EFRX-68P 0A82 PQ: 0 ANSI: 5 [ 13.934040] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 13.941801] sd 1:0:0:0: [sdb] 4096-byte physical blocks [ 13.947829] sd 1:0:0:0: [sdb] Write Protect is off [ 13.952968] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 13.972445] sd 1:0:0:0: [sdb] Attached SCSI disk [ 13.980172] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 13.985466] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 13.998415] xhci_hcd 0000:01:00.0: hcc params 0x014051cf hci version 0x100 quirks 0x00000090 [ 14.008409] hub 2-0:1.0: USB hub found [ 14.012655] hub 2-0:1.0: 2 ports detected [ 14.017117] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 14.022458] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 3 [ 14.030877] hub 3-0:1.0: USB hub found [ 14.034986] hub 3-0:1.0: 2 ports detected [ 14.046756] usbcore: registered new interface driver usb-storage [ 14.054329] Driver 'mmcblk' needs updating - please use bus_type methods [ 14.633875] init: - preinit - [ 14.696700] random: procd urandom read with 20 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 17.804666] procd: - early - [ 18.396371] procd: - ubus - [ 19.410763] procd: - init - Please press Enter to activate this console. [ 20.201599] NET: Registered protocol family 10 [ 20.231832] md: raid0 personality registered for level 0 [ 20.238594] md: raid1 personality registered for level 1 [ 20.247927] device-mapper: ioctl: 4.30.0-ioctl (2014-12-22) initialised: dm-devel@redhat.com [ 20.275775] loop: module loaded [ 20.285135] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 20.313647] i2c /dev entries driver [ 20.322172] gpio-fan soc:internal-regs:gpio_fan: GPIO fan initialized [ 20.339371] fuse init (API version 7.23) [ 20.357624] input: soc:internal-regs:gpio_keys as /devices/platform/soc/soc:internal-regs/soc:internal-regs:gpio_keys/input/input0 [ 20.388214] ip_tables: (C) 2000-2006 Netfilter Core Team [ 20.414875] nf_conntrack version 0.5.0 (8051 buckets, 32204 max) [ 20.458868] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6 [ 20.481253] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0 [ 20.523210] xt_time: kernel timezone is -0000 [ 23.701373] device eth0 entered promiscuous mode [ 23.713732] br-lan: port 1(eth0) entered forwarding state [ 23.719195] br-lan: port 1(eth0) entered forwarding state [ 23.807989] br-lan: port 1(eth0) entered disabled state [ 28.700017] mvneta d0074000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 28.707935] br-lan: port 1(eth0) entered forwarding state [ 28.713464] br-lan: port 1(eth0) entered forwarding state [ 30.709432] br-lan: port 1(eth0) entered forwarding state BusyBox v1.23.2 (2015-06-23 15:33:27 CEST) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- CHAOS CALMER (Bleeding Edge, r46314) ----------------------------------------------------- * 1 1/2 oz Gin Shake with a glassful * 1/4 oz Triple Sec of broken ice and pour * 3/4 oz Lime Juice unstrained into a goblet. * 1 1/2 oz Orange Juice * 1 tsp. Grenadine Syrup ----------------------------------------------------- root@OpenWrt:/# cat /proc/mtd dev: size erasesize name mtd0: 02000000 00020000 "boot" mtd1: 1e000000 00020000 "rootfs" mtd2: 000f0000 00010000 "u-boot" mtd3: 00010000 00010000 "u-boot-env" root@OpenWrt:/# fw_printenv sn=XXXXXXXXXXXXXXXXXXX eth1addr=XX:XX:XX:XX:XX:XX serverip=192.168.11.1 ipaddr=192.168.11.150 deviceid=_xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx SerialNo=XXXXXXXXXXXXXX root@OpenWrt:/#


Tags

toh/buffalo/ls421de.txt · Last modified: 2015/12/14 11:27 by tmomas