Buffalo WHR-G125

The WHR-G125 is a 802.11g wireless router with a 5 port programmable ethernet switch.

Supported Versions

Version/Model S/N OpenWrt Version Supported Model Specific Notes
v1.0 ? 8.09 Has unpopulated Hirose U.FL connector inside

Hardware Highlights

CPU Ram Flash Network USB Serial JTag
Broadcom BCM3302 V2.9 @ 240MHz 16MB 4MB 4 x 1 No Yes Yes

Installation

OpenWrt should be installed via TFTP, follow the instructions in the HOWTO section. The correct image for this device is openwrt-brcm-2.4-squashfs.trx .

Upgrading OpenWrt

This device is supported by sysupgrade.

LuCI Web Upgrade Process

Terminal Upgrade Process

  • Login as root via SSH on 192.168.1.1
  • Use the following commands to upgrade.

cd /tmp/
wget http://downloads.openwrt.org/latest/brcm-2.4/openwrt-brcm-2.4-squashfs.trx
sysupgrade openwrt-brcm-2.4-squashfs.trx

Hardware

Info

Architecture: MIPS (low endian)
Vendor: Broadcom
Bootloader: CFE 1.0.37-1.18
System-On-Chip: Broadcom BCM5354 rev 1
CPU Speed: 240 Mhz
Flash-Chip: Spansion S29AL032D90TFI04
Flash size: 4 MiB
RAM: 16 MiB
Wireless: Broadcom BCM4318 802.11b/g (integrated)
Ethernet: Broadcom BCM47xx 10/100BaseT Ethernet / RoboSwitch
USB: No
Serial: Yes
JTAG: Yes

Photos

Front: Back:

Opening the case

Note: This will void your warranty!

  • Remove the Torx screw under the bottom label
  • Gently tear off the bottom cover

Main PCB

Serial

FIXME Pin layout unknown yet

JTAG

The board has an unpopulated 12-pin Broadcom style JTAG port (JP2).

nTRST 1 2 dead TDI 3 4 dead TDO 5 6 dead TMS 7 8 dead TCK 9 10 dead nSRST 11 12 GND

How to connect to JTAG interface, and how to reflash the device with JTAG tools

See port.jtag for more JTAG details.

Specific Configuration

Interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
vlan0 (eth0.0) LAN ports (1 to 4) None
vlan1 (eth0.1) WAN port DHCP
wl0 WiFi Disabled

Switch Ports (for VLANs)

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself.

Port Switch port
Internet (WAN) 4
LAN 1 0
LAN 2 1
LAN 3 2
LAN 4 3

:!: In OpenWrt versions up to Backfire 10.03, the first LAN port and WAN are reversed after flashing!

To fix the port assignment, apply the following configuration changes:

root@OpenWrt:~# uci set network.eth0_0.ports='0 1 2 3 5' root@OpenWrt:~# uci set network.eth0_1.ports='4 5' root@OpenWrt:~# uci commit network root@OpenWrt:~# reboot

Failsafe mode

If you forgot your password, broken one of the startup scripts, firewalled yourself or corrupted the JFFS2 partition, you can get back in by using OpenWrt's failsafe mode. →generic.failsafe

Buffalo WHR-G125-specific

  • Unplug the router's power cord.
  • Connect the router's LAN1 port directly to your PC.
  • Configure your PC with a static IP address between 192.168.1.2 and 192.168.1.254. E. g. 192.168.1.2 (gateway and DNS is not required).
  • Plug the power on and wait for the DMZ LED to light up.
  • While the DMZ LED is on immediately press any button (Reset and Secure Easy Setup will work) a few times .
  • If done right the DMZ LED will quickly flash 3 times every second.
  • You should be able to telnet to the router at 192.168.1.1 now (no username and password)

Buttons

The Bufalo WHR-G125 has two buttons and one switch to toggle router and bridge mode when using the vendor firmware. These buttons can be used with hotplug events.

BUTTON Event
Router (switch) bridge
Reset reset
AOSS (AirStation One-Touch Secure Systemâ„¢) ses

Back to top

toh/buffalo/whr-g125.txt · Last modified: 2013/06/05 19:21 by lorema