Differences
This shows you the differences between two versions of the page.
|
toh:buffalo:whr-hp-g300n [2013/02/13 05:59] mdb add link to working tftp image |
toh:buffalo:whr-hp-g300n [2013/02/24 14:25] (current) guillaume54 |
||
|---|---|---|---|
| Line 10: | Line 10: | ||
| The TFTP images will be under the "ar71xx" branch rather than the "atheros" branch... successfully uploaded [[http://downloads.openwrt.org/snapshots/trunk/ar71xx/openwrt-ar71xx-generic-whr-hp-g300n-squashfs-tftp.bin|trunk/ar71xx/openwrt-ar71xx-generic-whr-hp-g300n-squashfs-tftp.bin]] (trunk on 2013-02-12: BARRIER BREAKER (Bleeding Edge, r35572)). | The TFTP images will be under the "ar71xx" branch rather than the "atheros" branch... successfully uploaded [[http://downloads.openwrt.org/snapshots/trunk/ar71xx/openwrt-ar71xx-generic-whr-hp-g300n-squashfs-tftp.bin|trunk/ar71xx/openwrt-ar71xx-generic-whr-hp-g300n-squashfs-tftp.bin]] (trunk on 2013-02-12: BARRIER BREAKER (Bleeding Edge, r35572)). | ||
| + | |||
| + | |||
| + | ===== TFTP Recovery on Mac os X ===== | ||
| + | |||
| + | Set your ethernet interface ip on 192.168.11.2 | ||
| + | |||
| + | Set your ethernet interface netmask on 255.255.255.0 | ||
| + | |||
| + | Add arp entry for 192.168.11.1 when the ethernet interface is up | ||
| + | |||
| + | sudo arp -s 192.168.11.1 aa:bb:cc:dd:ee:ff | ||
| + | |||
| + | Download the tftp version of the right firmware | ||
| + | Change the directory of your prompt to the firmware download directory | ||
| + | cd /Users/yourname/Downloads/ | ||
| + | |||
| + | Send your firware image with tftp | ||
| + | |||
| + | tftp 192.168.11.1 | ||
| + | |||
| + | *from this point, you're under tftp command prompt, the "tftp>" is the prompt tftp gives you, you just need to type the command AFTER that. | ||
| + | |||
| + | tftp> verbose | ||
| + | |||
| + | tftp> binary | ||
| + | |||
| + | tftp> trace | ||
| + | |||
| + | tftp> rexmt 1 | ||
| + | |||
| + | tftp> timeout 60 | ||
| + | |||
| + | Power on your router on and plug your ethernet on a LAN port | ||
| + | |||
| + | Send the command put until is success | ||
| + | |||
| + | tftp> put linux.bin | ||
| + | |||
| + | putting linux.bin to 192.168.11.1:linux.bin [octet] | ||
| + | sent WRQ <file=linux.bin, mode=octet> | ||
| + | tftp: sendto: Can't assign requested address | ||
| + | |||
| + | tftp> put linux.bin | ||
| + | |||
| + | putting linux.bin to 192.168.11.1:linux.bin [octet] | ||
| + | sent WRQ <file=linux.bin, mode=octet> | ||
| + | sent WRQ <file=linux.bin, mode=octet> | ||
| + | sent WRQ <file=linux.bin, mode=octet> | ||
| + | sent WRQ <file=linux.bin, mode=octet> | ||
| + | sent WRQ <file=linux.bin, mode=octet> | ||
| + | sent WRQ <file=linux.bin, mode=octet> | ||
| + | sent WRQ <file=linux.bin, mode=octet> | ||
| + | received ACK <block=0> | ||
| + | sent DATA <block=1, 512 bytes> | ||
| + | received ACK <block=1> | ||
| + | sent DATA <block=2, 512 bytes> | ||
| + | received ACK <block=2> | ||
| + | sent DATA <block=3, 512 bytes> | ||
| + | received ACK <block=3> | ||
| + | sent DATA <block=4, 512 bytes> | ||
| + | received ACK <block=4> | ||
| + | sent DATA <block=5, 512 bytes> | ||
| + | received ACK <block=5> | ||
| + | sent DATA <block=6, 512 bytes> | ||
| + | sent DATA <block=5633, 36 bytes> | ||
| + | received ACK <block=5633> | ||
| + | Sent 2883620 bytes in 8.0 seconds [2883620 bits/sec] | ||
| + | |||
| + | Wait and see ! ( at lease 10 min ) | ||
| + | |||
| + | The ROUTER light will flash and stop ! | ||
| + | |||
| + | Reboot and Enjoy | ||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
| + | |||
toh/buffalo/whr-hp-g300n.txt · Last modified: 2013/02/24 14:25 by guillaume54