User Tools

Site Tools


toh:buffalo:whr-hp-g300n

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

toh:buffalo:whr-hp-g300n [2013/07/04 21:38]
toh:buffalo:whr-hp-g300n [2014/10/11 21:35] (current)
locker Updated download link
Line 20: Line 20:
 Add arp entry for 192.168.11.1 when the ethernet interface is up Add arp entry for 192.168.11.1 when the ethernet interface is up
  
-sudo arp -s 192.168.11.1 aa:​bb:​cc:​dd:​ee:​ff ​+''​sudo arp -s 192.168.11.1 aa:​bb:​cc:​dd:​ee:​ff'' ​
  
 Download the tftp version of the right firmware Download the tftp version of the right firmware
Line 28: Line 28:
 Send your firware image with tftp Send your firware image with tftp
  
-tftp 192.168.11.1+''​tftp''​
  
 *from this point, you're under tftp command prompt, the "​tftp>"​ is the prompt tftp gives you, you just need to type the command AFTER that. *from this point, you're under tftp command prompt, the "​tftp>"​ is the prompt tftp gives you, you just need to type the command AFTER that.
 +
 +''​tftp>​ connect 192.168.11.1
  
 tftp> verbose tftp> verbose
Line 40: Line 42:
 tftp> rexmt 1  tftp> rexmt 1 
  
-tftp> timeout 60 +tftp> timeout 60'' ​
  
 Power on your router on and plug your ethernet on a LAN port Power on your router on and plug your ethernet on a LAN port
Line 46: Line 48:
 Send the command put until is success ​ Send the command put until is success ​
  
-tftp> put linux.bin+''​tftp> put linux.bin''​
  
-putting linux.bin to 192.168.11.1:​linux.bin [octet]+''​putting linux.bin to 192.168.11.1:​linux.bin [octet]
 sent WRQ <​file=linux.bin,​ mode=octet>​ sent WRQ <​file=linux.bin,​ mode=octet>​
-tftp: sendto: Can't assign requested address+tftp: sendto: Can't assign requested address''​
  
-tftp> put linux.bin+''​tftp> put linux.bin''​
  
-putting linux.bin to 192.168.11.1:​linux.bin [octet]+''​putting linux.bin to 192.168.11.1:​linux.bin [octet]
 sent WRQ <​file=linux.bin,​ mode=octet>​ sent WRQ <​file=linux.bin,​ mode=octet>​
 sent WRQ <​file=linux.bin,​ mode=octet>​ sent WRQ <​file=linux.bin,​ mode=octet>​
Line 76: Line 78:
 sent DATA <​block=5633,​ 36 bytes> sent DATA <​block=5633,​ 36 bytes>
 received ACK <​block=5633>​ received ACK <​block=5633>​
-Sent 2883620 bytes in 8.0 seconds [2883620 bits/sec]+Sent 2883620 bytes in 8.0 seconds [2883620 bits/sec]''​
  
 Wait and see ! ( at lease 10 min )  Wait and see ! ( at lease 10 min ) 
Line 89: Line 91:
  
 Download the firmware ​ Download the firmware ​
-[[http://​downloads.openwrt.org/​attitude_adjustment/12.09/​ar71xx/​generic/​openwrt-ar71xx-generic-whr-hp-g300n-squashfs-factory.bin+[[http://​downloads.openwrt.org/​barrier_breaker/14.07/​ar71xx/​generic/​openwrt-ar71xx-generic-whr-hp-g300n-squashfs-factory.bin
 ]] ]]
  
toh/buffalo/whr-hp-g300n.1372966714.txt.bz2 · Last modified: 2013/07/04 21:38 (external edit)