User Tools

Site Tools


toh:buffalo:whr-hp-g54

Buffalo WHR-HP-G54

802.11g wireless router with a 5 port programmable ethernet switch which supports VLANs. Very similar to the WHR-G54S but the WHR-HP-G54 is equiped with an internal wifi amplifier.

Supported Versions

Version/Model OpenWrt Notes
WHR-HP-G54 ≥ 7.09 OpenWrt versions ≥12.09 run easily out of memory
WHR-HP-G54-1
WHR-HP-G54-4

Latest OpenWrt usable version is Backfire (10.03.1) → openwrt-brcm-2.4-squashfs.trx

OEM source code available at: http://opensource.buffalo.jp/gpl_wireless.html

Hardware Highlights

SoC Ram Flash Network USB Serial JTag
Broadcom BCM5352@200MHz 16MiB 4MiB 5 x 1 No Yes Yes

Forum: https://forum.openwrt.org/viewtopic.php?id=???

Installation

Flash Layout

Please check out the article Flash Layout. It contains an example and a couple of explanations.

OEM flash layout
Offsets Size (kiB) description
0x00000000-0x00040000 256 "boot"
0x00040000-0x003e0000 3712 "linux"
0x00100000-0x003e0000 2944 "rootfs"
0x003e0000-0x00400000 128 "nvram"

OEM easy installation

You can't use the vendor firmware web interface to install Openwrt since it only accepts vendor encrypted firmwares. You must use the TFTP method instead.

OEM installation using the TFTP method

Specific values you need

Bootloader default tftp server IPv4 address 192.168.11.1
Firmware tftp image openwrt-brcm-2.4-squashfs.trx or openwrt-brcm47xx-squashfs.trx
TFTP Transfer Window 4 seconds
TFTP Window Start approximately 3 seconds after power on
TFTP Client Required IP Address any compatible with 192.168.11.1
  • Unplug the router's power cord.
  • Confirm your PC is configured to use a fixed IP in the 192.168.11.0/24 range (do not use .1).
  • Connect the router's LAN1 port directly to your PC.
  • The router accepts an image via TFTP, after powering on during a short time interval, be fast.

Execute the TFTP commands below:

  • Linux (or Mac OS X)
    tftp 192.168.11.1
    tftp> binary
    tftp> trace
    tftp> put openwrt-brcm-2.4-squashfs.trx
  • Windows
    tftp -i 192.168.11.1 PUT openwrt-brcm-2.4-squashfs.trx

After the TFTP upload is complete, wait at least six minutes. The firmware is first loaded into the RAM, and then flashed. This process takes a little time, and to ensure that the router is not bricked you should wait six minutes.

The router will reboot itself automatically after the upgrade is complete. Rebooting may take a while. It might be the case that the router does not reboot by itself; if this happens it should be safe to wait for the period mentioned and then to do a manual reboot (pull the power-cord).

You are done! You should be able to telnet to your router (IP address: 192.168.1.1 - even if you were using another one previously) and start configuring.

Upgrading OpenWrt

generic.sysupgrade

If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

LuCI Web Upgrade Process

Terminal Upgrade Process

  • Login as root via SSH on 192.168.1.1
  • Use the following commands to upgrade.

cd /tmp/
wget http://downloads.openwrt.org/snapshots/trunk/brcm47xx/openwrt-brcm47xx-squashfs.trx
sysupgrade /tmp/openwrt-brcm47xx-squashfs.trx

  • If sysupgrade does not support this router, use the following commands.

cd /tmp/
wget http://downloads.openwrt.org/snapshots/trunk/brcm47xx/openwrt-brcm47xx-squashfs.trx
mtd write /tmp/openwrt-brcm47xx-squashfs.trx linux && reboot

Basic configuration

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Specific Configuration

Interfaces

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
vlan0 (eth0.0) LAN ports (1 to 4) None
vlan1 (eth0.1) WAN port DHCP
wlan0 WiFi Disabled

Switch Ports (for VLANs)

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
Internet (WAN) 4
LAN 1 3
LAN 2 2
LAN 3 1
LAN 4 0

Failsafe mode

Buttons

hardware.button on howto use and configure the hardware button(s).

The Buffalo WHR-HP-G54 has two buttons and one slider switch. They are Reset, AOSS and bridge.

BUTTON Event
Reset reset
AOSS ses
BRI -

Enable Internal AMPLIFIER

Get into the shell and:type

nvram get boardflags
The result probably will be 0x1758 - enhanced receive sensitivity. The other settings are:
 0x0758 - no amp and receive sensitivity normal 

 0x2758 - amp on, normal receive 

 0x3758 - both amp and BroadRange enhanced receive sensitivity on 
i'm using 0x3758 and it's much better than the stock setting, to do it just
 nvram set boardflags=0x3758 

 nvram commit 

 reboot
Have Fun :)

Hardware

Info

Instruction set: MIPS
Vendor: Broadcom
Bootloader: CFE
System-On-Chip: Broadcom BCM5352
CPU @Frq BMIPS3300 V0.8 @200MHz
Flash size: 4 MiB
Flash Chip: Winbond W19B320ABT7H 48-pin TSOP
RAM size: 16 MiB
RAM Chips: MIRA P2V64S40ETP / SDR-133
Wireless: SoC-integrated: BCM5352 for 2.4GHz 802.11b/g
Antennas: 1 onboard, 1 external detachable
Switch: BCM5352 integrated (Fast-ethernet, VLAN)
USB: No, but possible with mod
Power adapter: 5V DC 2A / NU10-7050200-I3
Serial: Yes
JTAG: Yes

Photos

Model Number

Front:

Photo of front of the casing

Back:

Photo of back of the casing

Opening the case

Note: This will void your warranty!

  • To remove the cover do a/b/c

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

The serial port is located at the J1 pinheader.

You must use 3V3 TTL serial adapter:

115200 baud rate
8 data bits
1 stop bit
no parity
no handshake

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

The WHR-HP-G54 version (no trailing -1 or -4) version of this router is confirmed to have JTAG support. JTAG support on the other versions is unconfirmed. The WHR-HP-G54 board has thru-hole pads labeled CN1 for JTAG near the J1 serial header. The solder can be removed and a 12-pin header can be added for use with JTAG. The holes for the even pins are slightly smaller than the odd holes and it may be difficult to extract all the old solder enough to insert the header.

Old versions of the WRT54G EJTAG DeBrick Utility will not talk to this board; version 3.0 or newer will work. The

/noreset
option is required for all operations as of version 3.0 of the Utility.

Debricking

Bootloader Mods

  1. you could read about bootloader in general

Hardware mods

  1. as a beginner, you really should inform yourself about soldering in general and then obtain some practical experience!

xxMiB RAM Mod

It can be done. The board has pads for 4 chips, 2 at the top (unsoldered) and 2 at the bottom (RAM chips soldered), probably you can solder 4 RAM chips but might be with half bus width (8bit). There is no info on how to proceed with this mod, be the first one to add this info here.

Bootlogs

OEM bootlog

>0x80FFFFFF>complite CFE version 1.0.37-1.08 for BCM947XX (32bit,SP,LE) Build Date: 2006ǯ 7�� 11�� ������ 15:41:55 JST (root@ifedora) Copyright (C) 2000,2001,2002,2003 Broadcom Corporation. Initializing Arena Initializing Devices. * cmdset: AMD Standard * Insaner_1 = (0x7e) * flashutl_cmd: type (0004), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0003), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0002), read_id (0090) -> vendid (0019), devid (1000), devid2 (0000) * Flash Info. -> manufacturer (FF), device (FF) * Flash Info. -> manufacturer2 (0000), device2 (0000) * Insaner_2 = (0x7e) * cmdset: AMD Standard * Insaner_1 = (0x7e) * flashutl_cmd: type (0004), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0003), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0002), read_id (0090) -> vendid (0019), devid (1000), devid2 (0000) * Flash Info. -> manufacturer (FF), device (FF) * Flash Info. -> manufacturer2 (0000), device2 (0000) * Insaner_2 = (0x7e) * cmdset: AMD Standard * Insaner_1 = (0x7e) * flashutl_cmd: type (0004), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0003), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0002), read_id (0090) -> vendid (0019), devid (1000), devid2 (0000) * Flash Info. -> manufacturer (FF), device (FF) * Flash Info. -> manufacturer2 (0000), device2 (0000) * Insaner_2 = (0x7e) et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.39.0 * memc_config: (00048000) CPU type 0x29008: 200MHz Total memory: 16384 KBytes Total memory used by CFE: 0x80400000 - 0x804A39B0 (670128) Initialized Data: 0x80439670 - 0x8043C210 (11168) BSS Area: 0x8043C210 - 0x8043D9B0 (6048) Local Heap: 0x8043D9B0 - 0x804A19B0 (409600) Stack Area: 0x804A19B0 - 0x804A39B0 (8192) Text (code) segment: 0x80400000 - 0x80439670 (235120) Boot area (physical): 0x004A4000 - 0x004E4000 Relocation Factor: I:00000000 - D:00000000 Device eth0: hwaddr 00-1D-73-55-46-5C, ipaddr 192.168.11.1, mask 255.255.255.0 gateway not set, nameserver not set Wait a few seconds for an image Reading :: Failed.: Timeout occured >>> boot -raw -z -addr=0x80001000 -max=0x3a0000 flash0.os: Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) Loading: ...... 1740800 bytes read Entry at 0x80001000 Closing network. Starting program at 0x80001000 CPU revision is: 00029008 Primary instruction cache 16kb, linesize 16 bytes (2 ways) Primary data cache 8kb, linesize 16 bytes (2 ways) Linux version 2.4.20 (vc03021@mkitec_vc03021) (gcc version 3.3.3) #1 2006年 7� 21�� ���� 06:49:51 JST Setting the PFC to its default value Determined physical RAM map: memory: 01000000 @ 00000000 (usable) On node 0 totalpages: 4096 zone(0): 4096 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock2 noinitrd console=ttyS0,115200 CPU: BCM5352 rev 0 at 200 MHz Calibrating delay loop... 199.47 BogoMIPS Memory: 14140k/16384k available (1508k kernel code, 2244k reserved, 104k data, 64k init, 0k highmem) Dentry cache hash table entries: 2048 (order: 2, 16384 bytes) Inode cache hash table entries: 1024 (order: 1, 8192 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 4096 (order: 2, 16384 bytes) Checking for 'wait' instruction... unavailable. POSIX conformance testing by UNIFIX PCI: no core PCI: Fixing up bus 0 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 mel_initsw: GPIO initialize done.. BUFFALO SWICH&LED DRIVER ver 1.00 Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0xb8000300 (irq = 3) is a 16550A ttyS01 at 0xb8000400 (irq = 0) is a 16550A HDLC line discipline: version $Revision$, maxframe=4096 N_HDLC line discipline registered. PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered Amd/Fujitsu Extended Query Table v1.3 at 0x0040 number of CFI chips: 1 Flash device: 0x400000 at 0x1c000000 Physically mapped flash: cramfs filesystem found at block 1024 Creating 4 MTD partitions on "Physically mapped flash": 0x00000000-0x00040000 : "boot" 0x00040000-0x003e0000 : "linux" 0x00100000-0x003e0000 : "rootfs" 0x003e0000-0x00400000 : "nvram" sflash: found no supported devices NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 1024 bind 2048) ip_conntrack version 2.1 (128 buckets, 1024 max) - 344 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team *** #define HZ is (100). ipt_time loading NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: Ethernet Bridge 008 for NET4.0 802.1Q VLAN Support v1.7 Ben Greear All bugs added by David S. Miller VFS: Mounted root (cramfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 64k freed init started: BusyBox v1.00 (2006.07.20-22:00+0000) multi-call binary Algorithmics/MIPS FPU Emulator v1.5 mount: Mounting none on / failed: Permission denied MidLayer.c(1936) ML_Initialize :***** Please push init button if you want to init_reboot ****** insmod: /lib/modules/2.4.20: No such file or directory Using /lib/modules/kernel/drivers/net/et/et.o Warning: loading et will taint the kernel: no license See http://www.tux.org/lkml/#export-tainted for information about tainted modules eth0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.130.25.0 Please press Enter to activate this console. wl_module_init: Generic GPIO initialize done.. create procpoint for station information eth%d eth1: Broadcom BCM4318 802.11 Wireless Controller 3.130.25.0 et0: link up (interface up) register_vlan_device: ALREADY had VLAN registered register_vlan_device: ALREADY had VLAN registered wl0: Performing WLC_COMMIT wl0: Channel Select: 11 BusyBox v1.00 (2006.07.20-22:00+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. # cat /proc/cpuinfo system type : Broadcom BCM947XX processor : 0 cpu model : BCM3302 V0.8 BogoMIPS : 199.47 wait instruction : no microsecond timers : yes tlb_entries : 32 extra interrupt vector : no hardware watchpoint : no VCED exceptions : not available VCEI exceptions : not available unaligned_instructions : 0 dcache hits : 2144792486 dcache misses : 380623622 icache hits : 1430974614 icache misses : 4068134645 instructions : 0 #

OpenWrt bootlog

>0x80FFFFFF>complite CFE version 1.0.37-1.08 for BCM947XX (32bit,SP,LE) Build Date: 2006ǯ 7�� 11�� ������ 15:41:55 JST (root@ifedora) Copyright (C) 2000,2001,2002,2003 Broadcom Corporation. Initializing Arena Initializing Devices. * cmdset: AMD Standard * Insaner_1 = (0x7e) * flashutl_cmd: type (0004), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0003), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0002), read_id (0090) -> vendid (0019), devid (1000), devid2 (0000) * Flash Info. -> manufacturer (FF), device (FF) * Flash Info. -> manufacturer2 (0000), device2 (0000) * Insaner_2 = (0x7e) * cmdset: AMD Standard * Insaner_1 = (0x7e) * flashutl_cmd: type (0004), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0003), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0002), read_id (0090) -> vendid (0019), devid (1000), devid2 (0000) * Flash Info. -> manufacturer (FF), device (FF) * Flash Info. -> manufacturer2 (0000), device2 (0000) * Insaner_2 = (0x7e) * cmdset: AMD Standard * Insaner_1 = (0x7e) * flashutl_cmd: type (0004), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0003), read_id (0090) -> vendid (00DA), devid (227E), devid2 (0000) * flashutl_cmd: type (0002), read_id (0090) -> vendid (0019), devid (1000), devid2 (0000) * Flash Info. -> manufacturer (FF), device (FF) * Flash Info. -> manufacturer2 (0000), device2 (0000) * Insaner_2 = (0x7e) et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 3.90.39.0 * memc_config: (00048100) CPU type 0x29008: 200MHz Total memory: 16384 KBytes Total memory used by CFE: 0x80400000 - 0x804A39B0 (670128) Initialized Data: 0x80439670 - 0x8043C210 (11168) BSS Area: 0x8043C210 - 0x8043D9B0 (6048) Local Heap: 0x8043D9B0 - 0x804A19B0 (409600) Stack Area: 0x804A19B0 - 0x804A39B0 (8192) Text (code) segment: 0x80400000 - 0x80439670 (235120) Boot area (physical): 0x004A4000 - 0x004E4000 Relocation Factor: I:00000000 - D:00000000 Device eth0: hwaddr 00-1D-73-55-46-5C, ipaddr 192.168.11.1, mask 255.255.255.0 gateway not set, nameserver not set Wait a few seconds for an image Reading :: Failed.: Timeout occured >>> boot -raw -z -addr=0x80001000 -max=0x3a0000 flash0.os: Loader:raw Filesys:raw Dev:flash0.os File: Options:(null) Loading: .. 3712 bytes read Entry at 0x80001000 Closing network. Starting program at 0x80001000 [ 0.000000] Linux version 3.10.36 (openwrt@gb-12) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40561) ) #1 Thu Apr 24 06:10:30 UTC 2014 [ 0.000000] CPU revision is: 00029008 (Broadcom BMIPS3300) [ 0.000000] bcm47xx: using ssb bus [ 0.000000] ssb: Found chip with id 0x5352, rev 0x00 and package 0x02 [ 0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000 [ 0.000000] MIPS: machine is Buffalo WHR-HP-G54 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 01000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x00ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x00ffffff] [ 0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 8kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064 [ 0.000000] Kernel command line: noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 64 (order: -4, 256 bytes) [ 0.000000] Dentry cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Inode-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Memory: 12756k/16384k available (2418k kernel code, 3628k reserved, 590k data, 184k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.080000] Calibrating delay loop... 199.06 BogoMIPS (lpj=995328) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.130000] bio: create slab at 0 [ 0.150000] Switching to clocksource MIPS [ 0.180000] NET: Registered protocol family 2 [ 0.180000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.180000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.180000] TCP: Hash tables configured (established 512 bind 512) [ 0.180000] TCP: reno registered [ 0.180000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.180000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.190000] NET: Registered protocol family 1 [ 0.200000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.200000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.200000] msgmni has been set to 24 [ 0.200000] io scheduler noop registered [ 0.200000] io scheduler deadline registered (default) [ 0.200000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.250000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A [ 0.510000] console [ttyS0] enabled [ 0.530000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A [ 0.550000] physmap platform flash device: 02000001 at 1c000000 [ 0.560000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x00ddda Chip ID 0x00227e [ 0.570000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.570000] Amd/Fujitsu Extended Query version 1.3. [ 0.580000] number of CFI chips: 1 [ 0.600000] 6 bcm47xxpart partitions found on MTD device physmap-flash.0 [ 0.610000] Creating 6 MTD partitions on "physmap-flash.0": [ 0.610000] 0x000000000000-0x000000040000 : "boot" [ 0.620000] 0x000000040000-0x0000003f0000 : "firmware" [ 0.640000] 0x00000004001c-0x00000004090c : "loader" [ 0.650000] 0x00000004090c-0x00000014bc00 : "linux" [ 0.650000] mtd: partition "linux" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.670000] 0x00000014bc00-0x0000003f0000 : "rootfs" [ 0.680000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.700000] mtd: device 4 (rootfs) set to be root filesystem [ 0.700000] mtd: partition "rootfs_data" created automatically, ofs=0x330000, len=0xc0000 [ 0.710000] 0x000000330000-0x0000003f0000 : "rootfs_data" [ 0.730000] 0x0000003f0000-0x000000400000 : "nvram" [ 0.750000] libphy: Fixed MDIO Bus: probed [ 0.760000] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer) [ 0.770000] GPIO_WDT: failed to register misc device [ 0.780000] TCP: cubic registered [ 0.780000] NET: Registered protocol family 17 [ 0.790000] Bridge firewalling registered [ 0.790000] 8021q: 802.1Q VLAN Support v1.8 [ 0.820000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4. [ 0.830000] Freeing unused kernel memory: 184K (802f2000 - 80320000) procd: Console is alive procd: - watchdog - procd: - preinit - [ 8.220000] pps_core: LinuxPPS API ver. 1 registered [ 8.220000] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 8.250000] PTP clock support registered [ 8.260000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0 [ 8.280000] libphy: b44_eth_mii: probed [ 8.290000] b53_common: found switch: BCM5325, rev 0 [ 8.300000] b44 ssb0:0: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=1:1e) [ 8.310000] b44 ssb0:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:1d:73:55:46:5c [ 8.330000] bgmac: Broadcom 47xx GBit MAC driver loaded [ 9.320000] b44 ssb0:0 eth0: Link is down [ 10.320000] b44 ssb0:0 eth0: Link is down [ 11.300000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex [ 11.300000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level jffs2 is ready [ 15.650000] jffs2: notice: (251) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 20 of xref (0 dead, 0 orphan) found. switching to jffs2 [ 15.720000] b44 ssb0:0 eth0: powering down PHY procd: - early - procd: - watchdog - [ 16.350000] b44 ssb0:0 eth0: Link is down procd: - ubus - procd: - init - Please press Enter to activate this console. [ 21.680000] Loading modules backported from Linux version master-2014-03-31-1-0-g5c109d2 [ 21.690000] Backport generated by backports.git backports-20140221-0-g8e94650 [ 21.760000] cfg80211: Calling CRDA to update world regulatory domain [ 21.770000] cfg80211: World regulatory domain updated: [ 21.770000] cfg80211: DFS Master region: unset [ 21.780000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 21.790000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 21.790000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 21.800000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 21.810000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 21.820000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 21.830000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 22.090000] b43-phy0: Broadcom 5352 WLAN found (core revision 9) [ 22.150000] b43-phy0: Found PHY: Analog 2, Type 2 (G), Revision 7 [ 22.210000] Broadcom 43xx driver loaded [ Features: PNL ] [ 23.730000] Broadcom 43xx-legacy driver loaded [ Features: PLD ] procd: - init complete - [ 42.140000] b44 ssb0:0 eth0: Link is down [ 42.160000] device eth0.1 entered promiscuous mode [ 42.170000] device eth0 entered promiscuous mode [ 43.140000] b44 ssb0:0 eth0: Link is down [ 43.330000] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex [ 43.330000] b44 ssb0:0 eth0: Flow control is off for TX and off for RX [ 43.370000] br-lan: port 1(eth0.1) entered forwarding state [ 43.370000] br-lan: port 1(eth0.1) entered forwarding state [ 45.370000] br-lan: port 1(eth0.1) entered forwarding state [ 47.540000] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07) [ 47.710000] device wlan0 entered promiscuous mode [ 47.770000] br-lan: port 2(wlan0) entered forwarding state [ 47.770000] br-lan: port 2(wlan0) entered forwarding state [ 49.770000] br-lan: port 2(wlan0) entered forwarding state BusyBox v1.19.4 (2014-04-24 05:56:10 UTC) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- BARRIER BREAKER (Bleeding Edge, r40561) ----------------------------------------------------- * 1/2 oz Galliano Pour all ingredients into * 4 oz cold Coffee an irish coffee mug filled * 1 1/2 oz Dark Rum with crushed ice. Stir. * 2 tsp. Creme de Cacao ----------------------------------------------------- root@OpenWrt:/# cat /proc/cpuinfo system type : Broadcom BCM5352 machine : Buffalo WHR-HP-G54 processor : 0 cpu model : Broadcom BMIPS3300 V0.8 BogoMIPS : 199.06 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : yes hardware watchpoint : no isa : mips1 mips2 mips32r1 ASEs implemented : shadow register sets : 1 kscratch registers : 0 core : 0 VCED exceptions : not available VCEI exceptions : not available root@OpenWrt:/#

Notes

Tags

For some Help with the Tags, please have a look here: tags

toh/buffalo/whr-hp-g54.txt · Last modified: 2014/04/26 13:31 (external edit)