Wiki Search

Actions

Donate

Flattr this

Translations

You are here: OpenWrt Wiki » Table of Hardware » Buffalo » Buffalo WZR-AG300NH

Differences

This shows you the differences between two versions of the page.

toh:buffalo:wzr-ag300nh [2012/11/16 15:28]
ebzip created 		toh:buffalo:wzr-ag300nh [2012/11/17 12:02] (current)
ebzip
Line 1: Line 1:
====== Buffalo WZR-AG300NH ====== ====== Buffalo WZR-AG300NH ======
 +===== OpenWrt support =====
 +
 +Currently there is **no support for OpenWrt** on this router; initial porting efforts are in progress.
 +
 +===== Hardware details =====
 +
 +  * SoC: Marvell 88F5181
 +  * CPU: ARM926EJ @ 500MHz
 +  * 8-Port Gigabit Ethernet Switch: Marvell 88E6131
 +  * Two gigabit transceivers: Marvell 88E1112
 +  * Two MAC/baseband chips: Marvell 88W8363
 +  * Two 2.4 / 5 GHz RF transceiver chips: Marvell 88W8060
 +  * Flash: 8MB (Samsung K8D6316UBM-PI07)
 +  * RAM: 32MB (DDR SDRAM - ProMOS V58C2128164SBI5 x 2)
 +
 +This is pretty similar compared to Netgear WNR3500v1 except for the additional 5GHz radio.
 +
 +===== Serial console =====
 +
 +There is a 4-pin serial console header on the mainboard (next to the ProMOS RAM chip). 
 +
 +|**Pin 1**| Vcc +3.3V |
 +|**Pin 2**| Gnd |
 +|**Pin 3**| Tx |
 +|**Pin 4**| Rx |
 +|Settings| 115200,8,N,1|
 +
 +The serial console gives you full access to the bootloader and a root shell once the factory firmware is booted.
 +
 +{{:toh:buffalo:wzr-ag300nh-serial-port.jpg|}}
 +
 +----
 +
 +==== Boot Log ====
 +<HTML>
 +<p style="padding: 10px;border:1px solid grey;height:600px;font:10px/14px Georgia, Garamond, Serif;overflow:Auto;background-color:#FFFFFF">
 +<code>
 +# reboot
 +# umount: ramfs busy - remounted read-only
 +umount: none busy - remounted read-only
 +The system is going down NOW !!
 +Sending SIGTERM to all processes.
 +Jan  1 00:02:00 2008 (none) syslog.info System log daemon exiting.
 +SendZPlease stand by while rebooting the system.
 +Restarting system.
 +Resetting!
 +
 +        __  __                      _ _
 +        |  \/  | __ _ _ ____  _____| | |
 +        | |\/| |/ _` | '__\ \ / / _ \ | |
 +        | |  | | (_| | |  \ V /  __/ | |
 +        |_|  |_|\__,_|_|    \_/ \___|_|_|
 + _  _    ____              _
 +| | | |  | __ )  ___  ___ | |_
 +| | | |___|  _ \ / _ \ / _ \| __|
 +| |_| |___| |_) | (_) | (_) | |_
 + \___/    |____/ \___/ \___/ \__|  ** LOADER **
 + ** MARVELL BOARD: RD-88F5181L-VOIP-GE LE
 +
 +U-Boot 1.1.1 for BUFFALO AIRSTATION (Mar 22 2007 - 09:22:20) Marvell version: 1.10.8
 +
 +  # Buffalo Version: 1.09
 +
 +DRAM CS[0] base 0x00000000  size  32MB
 +DRAM Total size  32MB
 +Memory Test start(00000000) end(02000000) size(02000000)
 +Pattern 55555555  Writing...            Reading...Pattern AAAAAAAA  Writing...            Reading...Pattern 00000000  Writing...            Reading...
 +Memory Test OK
 +Unknown Vendor 0xecUnknown Chip Type id 0x22e2
 +Size:  8 MB,Bus Width: 2, device Width: 2.
 +Flash base: 0xff800000,Number of Sectors: 135 Type: BOTTOM.
 +  Sector Start Addresses:
 +    00000000      00002000      00004000      00006000      00008000   
 +    0000a000      0000c000      0000e000      00010000      00020000   
 +    00030000      00040000      00050000      00060000      00070000   
 +    00080000      00090000      000a0000      000b0000      000c0000   
 +    000d0000      000e0000      000f0000      00100000      00110000   
 +    00120000      00130000      00140000      00150000      00160000   
 +    00170000      00180000      00190000      001a0000      001b0000   
 +    001c0000      001d0000      001e0000      001f0000      00200000   
 +    00210000      00220000      00230000      00240000      00250000   
 +    00260000      00270000      00280000      00290000      002a0000   
 +    002b0000      002c0000      002d0000      002e0000      002f0000   
 +    00300000      00310000      00320000      00330000      00340000   
 +    00350000      00360000      00370000      00380000      00390000   
 +    003a0000      003b0000      003c0000      003d0000      003e0000   
 +    003f0000      00400000      00410000      00420000      00430000   
 +    00440000      00450000      00460000      00470000      00480000   
 +    00490000      004a0000      004b0000      004c0000      004d0000   
 +    004e0000      004f0000      00500000      00510000      00520000   
 +    00530000      00540000      00550000      00560000      00570000   
 +    00580000      00590000      005a0000      005b0000      005c0000   
 +    005d0000      005e0000      005f0000      00600000      00610000   
 +    00620000      00630000      00640000      00650000      00660000   
 +    00670000      00680000      00690000      006a0000      006b0000   
 +    006c0000      006d0000      006e0000      006f0000      00700000   
 +    00710000      00720000      00730000      00740000      00750000   
 +    00760000      00770000      00780000      00790000      007a0000   
 +    007b0000      007c0000      007d0000      007e0000      007f0000   
 +[8192kB@ff800000] Flash:  8 MB
 +Addresses 20M - 0M are saved for the U-Boot usage.
 +Mem malloc Initialization (20M - 16M): Done
 +### buf_ver=[1.09] U-Boot Ver.=[1.09]
 +### build_date(env)=[Mar 22 2007 - 09:22:20] build_date(bin)=[Mar 22 2007 - 09:22:20]
 +
 +Soc: 88F5181 B1
 +CPU: ARM926 (Rev 0) running @ 500Mhz
 +Orion 1 streaming disabled
 +SysClock = 166Mhz , TClock = 166Mhz
 +
 +
 +USB 0: host mode
 +PCI 0: PCI Express Root Complex Interface
 +PCI 1: Conventional PCI, speed = 33000000
 +Net:  egiga0 [PRIME]
 +Hit any key to stop autoboot:  1  0
 +
 +tftp server(receive) go, waiting:4[sec]
 +Load address: 0x400000
 +
 +TftpServer Timeout;
 +no file was loaded.
 +### CRAMFS loading 'uImage' to 0x400000
 +### CRAMFS load complete: 1024112 bytes loaded to 0x400000
 +## Booting image at 00400000 ...
 +  Image Name:  Linux-2.4.27-vrs1
 +  Image Type:  ARM Linux Kernel Image (uncompressed)
 +  Data Size:    1024048 Bytes = 1000 kB
 +  Load Address: 00008000
 +  Entry Point:  00008000
 +  Verifying Checksum ... OK
 +OK
 +
 +Starting kernel ...
 +
 +Uncompressing Linux...................................................................... done, booting the kernel.
 +ZLinux version 2.4.27-vrs1 (vc03021@mkitec-xen) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-1)) #1 Thu Jan 10 20:23:58 JST 2008
 +CPU: ARM926EJ-Sid(wb) revision 0
 +Machine: MV-88fxx81
 +Using UBoot passing parameters structure
 +Sys Clk = 166666667, Tclk = 166666667
 +
 +
 +- Warning - This LSP release was tested only with U-Boot release 1.10.16
 +
 +On node 0 totalpages: 8192
 +zone(0): 8192 pages.
 +zone(1): 0 pages.
 +zone(2): 0 pages.
 +Kernel command line: console=ttyS0,115200 mtdparts=phys_mapped_flash:7m(root),1m@7m(uboot)ro root=/dev/mtdblock1 rw ip=192.168.11.1:192.168.11.108:::DB88FXX81:eth0:none
 +Calibrating delay loop... 332.59 BogoMIPS
 +Memory: 32MB 0MB 0MB 0MB = 32MB total
 +Memory: 30040KB available (1915K code, 341K data, 76K init)
 +Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
 +Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
 +Mount cache hash table entries: 512 (order: 0, 4096 bytes)
 +Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
 +Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
 +CPU: Testing write buffer: pass
 +POSIX conformance testing by UNIFIX
 +init hw started.
 +
 +CPU Interface
 +-------------
 +SDRAM_CS0 ....base 00000000, size  32MB
 +SDRAM_CS1 ....disable
 +SDRAM_CS2 ....disable
 +SDRAM_CS3 ....disable
 +PEX0_MEM ....base e0000000, size 128MB
 +PEX0_IO ....base f2000000, size  1MB
 +PCI0_MEM ....base e8000000, size 128MB
 +PCI0_IO ....base f2100000, size  1MB
 +INTER_REGS ....base f1000000, size  1MB
 +DEVICE_CS0 ....no such
 +DEVICE_CS1 ....no such
 +DEVICE_CS2 ....no such
 +DEV_BOOCS ....base f4000000, size  16MB
 +Flash bankwidth 2, base f4000000, size 1000000
 +PCI: bus0: Fast back to back transfers enabled
 +HW already initialized.
 +PCI: bus1: Fast back to back transfers enabled
 +Linux NET4.0 for Linux 2.4
 +Based upon Swansea University Computer Society NET3.039
 +Initializing RT netlink socket
 +
 +  Marvell Development Board (LSP Version 1.1.3)-- RD-88F5181L-VOIP-GE  Soc: 88F5181 B1
 +
 + Detected Tclk 166666667 and SysClk 166666667
 +Starting kswapd
 +Journalled Block Device driver loaded
 +devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
 +devfs: boot_options: 0x1
 +JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
 +mel_initsw: GPIO initialize done..
 +BUFFALO SWICH & LED DRIVER ver 1.00
 +Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
 +ttyS00 at 0xf1012000 (irq = 3) is a 16550A
 +HDLC line discipline: version $Revision: 3.7 $, maxframe=4096
 +N_HDLC line discipline registered.
 +Marvell Gateway Driver:
 +Detected RD_88F5181L_VOIP_GE
 +Using VLAN-tag Mode
 +L3/L4 Checksum offload enabled
 +Link status indication mode is on (switch irq=40)
 +Multi queue support ( rxq0=128 rxq1=64 rxq2=64 rxq3=64 txq0=2000 )
 +Using boot network interface configuration
 +eth0: mac_addr 00:16:01:ab:06:1d, VID 0x100, port list: port-4
 +eth1: mac_addr 00:16:01:ab:06:1d, VID 0x200, port list: port-0 port-1 port-2 port-3
 +init switch layer... my_gateway: SetPhyReg(port=0,pd_port=2)=1111
 +my_gateway: SetPhyReg(port=1,pd_port=1)=1111
 +my_gateway: SetPhyReg(port=2,pd_port=0)=1111
 +my_gateway: SetPhyReg(port=3,pd_port=7)=1111
 +my_gateway: SetPhyReg(port=4,pd_port=5)=1111
 +done
 +init MAC layer... done
 +loading network interfaces: eth0 eth1
 +PPP generic driver version 2.4.2
 +PPP Deflate Compression module registered
 +PPP BSD Compression module registered
 +physmap flash device: 1000000 at f4000000
 + Amd/Fujitsu Extended Query Table v0.0 at 0x0040
 +number of CFI chips: 1
 +cfi_cmdset_0002: Disabling fast programming due to code brokenness.
 +Using physmap partition definition
 +Creating 4 MTD partitions on "Physically mapped flash":
 +0x00000000-0x00780000 : "rootfs"
 +0x00780000-0x007a0000 : "user_property"
 +0x007a0000-0x007c0000 : "uboot_environ"
 +0x007c0000-0x00800000 : "uboot"
 +Initializing Cryptographic API
 +IPv6 v0.8 (usagi-cvs) for NET4.0
 +IPv6 over IPv4 tunneling driver
 +NET4: Linux TCP/IP 1.0 for NET4.0
 +IP Protocols: ICMP, UDP, TCP
 +IP: routing cache hash table of 512 buckets, 4Kbytes
 +TCP: Hash tables configured (established 2048 bind 4096)
 +ip_conntrack version 2.1 (256 buckets, 2048 max) - 316 bytes per conntrack
 +ip_tables: (C) 2000-2002 Netfilter core team
 +ipt_time loading
 +NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
 +ip6_tables: (C) 2000-2002 Netfilter core team
 +NET4: Ethernet Bridge 008 for NET4.0
 +Fast Floating Point Emulator V0.94M by Peter Teichmann.
 +VFS: Mounted root (cramfs filesystem).
 +Mounted devfs on /dev
 +Freeing init memory: 76K
 +=ZZZinit started:  BusyBox v1.00 (2008.01.10-11:29+0000) multi-call binary
 +ZMidLayer.c(1953) ML_Initialize :***** Please push init button if you want to init_reboot ******
 +insmod: /lib/modules/2.4.27-vrs1: No such file or directory
 +insmod: ae531x.o: no module by that name found
 +insmod: /lib/modules/2.4.27-vrs1: No such file or directory
 +Using /lib/modules/kernel/drivers/net/wl/ap8x-8363.o
 +Warning: loading ap8x-8363 will taint the kernel: non-GPL license - Proprietary
 +  See http://www.tux.org/lkml/#export-tainted for information about tainted modules
 +ap0: Marvell AP-8x 802.11n adapter: mem=0xe8000000, irq=38
 +Z
 +Please press Enter to activate this console. ap1: Marvell AP-8x 802.11n adapter: mem=0xe8020000, irq=36
 +mv_gateway: starting eth1
 +mv_gateway: eth1 db1 port-mask=0x8, 00:16:01:ab:06:1d added
 +mv_gateway: eth1 db1 port-mask=0x8f, ff:ff:ff:ff:ff:ff added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:02 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:ff:ab:06:1d added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:02 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 01:00:5e:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:ff:ab:06:1d added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:02 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 01:00:5e:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:ff:ab:06:1d added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:02 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 01:00:5e:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:ff:ab:06:1d added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:02 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:01 added
 +mv_gateway: starting eth0
 +mv_gateway: eth0 db0 port-mask=0x8, 00:16:01:ab:06:1d added
 +mv_gateway: eth0 db0 port-mask=0x28, ff:ff:ff:ff:ff:ff added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:01 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:02 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:01 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:ff:ab:06:1d added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:02 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:01 added
 +mv_gateway: eth0 db0 port-mask=0x28, 01:00:5e:00:00:01 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:ff:ab:06:1d added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:02 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:01 added
 +mv_gateway: eth0 db0 port-mask=0x28, 01:00:5e:00:00:01 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:ff:ab:06:1d added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:02 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:01 added
 +mv_gateway: eth0 db0 port-mask=0x28, 01:00:5e:00:00:01 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:ff:ab:06:1d added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:02 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:01 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:e8:67:64:30 added
 +mv_gateway: eth0 db0 port-mask=0x28, 01:00:5e:00:00:01 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:ff:ab:06:1d added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:02 added
 +mv_gateway: eth0 db0 port-mask=0x28, 33:33:00:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:e8:67:64:30 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 01:00:5e:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:ff:ab:06:1d added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:02 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:e8:67:64:30 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 01:00:5e:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:ff:ab:06:1d added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:02 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:e8:67:64:30 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 01:00:5e:00:00:01 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:ff:ab:06:1d added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:02 added
 +mv_gateway: eth1 db1 port-mask=0x8f, 33:33:00:00:00:01 added
 +br_add_if:253: add device eth1 to br0, with rule 00000000
 +br_add_if:253: add device eth0 to br0, with rule 00000000
 +<mapping sub-ioctl htbw to cmd 0x8BE0-19>
 +<mapping sub-ioctl extsubch to cmd 0x8BE0-21>
 +<mapping sub-ioctl autochannel to cmd 0x8BE0-26>
 +<mapping sub-ioctl filter to cmd 0x8BE0-16>
 +<mapping sub-ioctl htbw to cmd 0x8BE0-19>
 +<mapping sub-ioctl extsubch to cmd 0x8BE0-21>
 +<mapping sub-ioctl autochannel to cmd 0x8BE0-26>
 +<mapping sub-ioctl filter to cmd 0x8BE0-16>
 +br_add_if:253: add device ap0 to br0, with rule 00000000
 +br_add_if:253: add device ap1 to br0, with rule 00000000
 +</code>
 +</p>
 +</HTML>

Back to top

toh/buffalo/wzr-ag300nh.1353076126.txt.bz2 · Last modified: 2012/11/16 15:28 by ebzip