Lan Port Mappings for /etc/config/network

To flash the WZR-HP-G300NH2, follow the same procedure as the wzr-hp-g300h, but use 02:AA:BB:CC:DD:1A for the static arp entry. Download the latest image here: Nightly snapshot build ( Flashing Backfire to this router will brick the router ( solid red light ) as this version has a new ethernet driver ). As noted under forum post #452 current fimwares sometimes don't show the correct LED status (due to a bug). This means the flash might appear to have failed (solid red light) but instead was successful. After any flash it is therefore recommended to follow the normal first login instructions regardless of LED status.

BUFFALO U-BOOT Ver 1.03 == CPU:400MHz, DDR:400MHz, AHB:200MHz == PB93 (ar7241 - Virian) U-boot DRAM: 64 MB WAN port disabling: done Top of RAM usable for U-Boot at: 84000000 Reserving 265k for U-Boot at: 83fbc000 Reserving 192k for malloc() at: 83f8c000 Reserving 44 Bytes for Board Info at: 83f8bfd4 Reserving 36 Bytes for Global Data at: 83f8bfb0 Reserving 128k for boot params() at: 83f6bfb0 Stack Pointer at: 83f6bf98 Now running in RAM - U-Boot at: 83fbc000 flash bank #0 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256] flash bank #1 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256] Flash: 32 MB In: serial Out: serial Err: serial Memory Test uboot use 83F6BFB0 - 84000000 Memory Test start(80000000) end(83F00000) size(03F00000) Pattern 00000000 Writing... Reading... Memory Test OK ### buf_ver=[1.03] U-Boot Ver.=[1.03] ### build_date(env)=[Mar 7 2011 - 05:27:46] build_date(bin)=[Mar 7 2011 - 05:27:46] ag7240_enet_initialize... Reading MAC Address from ENV(0x83f8c322) No valid address in Flash. Using fixed address Virian MDC CFG Value ==> 4 : cfg1 0x7 cfg2 0x7014 eth0: 02:aa:bb:cc:dd:1a eth0 up Virian MDC CFG Value ==> 4 : cfg1 0xf cfg2 0x7214 eth1: 00:03:7f:09:0b:ad ATHRS26: resetting s26 ATHRS26: s26 reset done eth1 up eth0 02:AA:BB:CC:DD:1A , eth1 00:03:7F:09:0B:AD dup 1 speed 1000 tftp server(receive) go, waiting:4[sec] Load address: 0x81f00000 $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ tftp server done Bytes transferred = 2621476 (280024 hex) Airstation Public header Recv fw image [2621444] bytes, now writing... flash-addr 0xBF060000 - 0xBF2EFFFF search sector 0xbf060000 - 0xbf2effff BANK #1 (6 : 46) 000 PPPP.Poooooooooooooooooooooooooo 032 ooooooooooooooo................. 064 ................................ 096 ................................ 128 ................................ 160 ................................ 192 ................................ 224 ................................ BANK #2 (-1 : -1) 000 ................................ 032 ................................ 064 ................................ 096 ................................ 128 ................................ 160 ................................ 192 ................................ 224 ................................ First 0x6 last 0x2e sector size 0x10000 46 Erased 41 sectors Copy to Flash... Copy 2621444 byte to Flash... write data: 81f00020 --> bf060000 (len:280004) done change bootargs console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@320k(ART),64k@8128k(properties),8192k@8192k(flash1),16384k@16384k(flash2) mem=64M product_rev=1 ## Booting image at bf060000 ... Image Name: MIPS OpenWrt Linux-2.6.39.4 Created: 2011-12-15 18:39:27 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 871284 Bytes = 850.9 kB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum ... crc32_fw: bf060040 - bf134bb3 (len:000d4b74) calc... crc32_fw: range1 bf060040 - bf134bb3 OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ... [ 0.000000] Linux version 2.6.39.4 (mdeneen@build) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Thu Dec 15 13:39:21 EST 2011 [ 0.000000] prom: fw_arg0=00000008, fw_arg1=a3f6bfb0, fw_arg2=a3f6c4b0, fw_arg3=00000020 [ 0.000000] MyLoader: sysp=00000000, boardp=00000000, parts=00000000 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR7242 rev 1 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 802b9570, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=WZR-HP-G300NH2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61848k/65536k available (2013k kernel code, 3688k reserved, 393k data, 184k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:80 [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.100000] MIPS: machine is Buffalo WZR-HP-G300NH2 [ 0.100000] ar71xx: pll_reg 0xb805002c: 0x62000000 [ 0.530000] registering PCI controller with io_map_base unset [ 0.540000] bio: create slab at 0 [ 0.550000] pci 0000:00:00.0: [168c:ff1c] type 0 class 0x000200 [ 0.550000] pci 0000:00:00.0: fixup device configuration [ 0.550000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit] [ 0.550000] pci 0000:00:00.0: supports D1 [ 0.550000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.550000] pci 0000:00:00.0: PME# disabled [ 0.550000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit] [ 0.560000] pci 0000:00:00.0: BAR 0: set to [mem 0x10000000-0x1000ffff 64bit] (PCI address [0x10000000-0x1000ffff]) [ 0.570000] PCI: mapping irq 72 to pin1@0000:00:00.0 [ 0.570000] Switching to clocksource MIPS [ 0.580000] NET: Registered protocol family 2 [ 0.580000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.580000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.590000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.590000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.600000] TCP reno registered [ 0.600000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.610000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.610000] NET: Registered protocol family 1 [ 0.620000] PCI: CLS 0 bytes, default 32 [ 0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.640000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.650000] msgmni has been set to 120 [ 0.660000] io scheduler noop registered [ 0.660000] io scheduler deadline registered (default) [ 0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.690000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.700000] console [ttyS0] enabled, bootconsole disabled [ 0.710000] Atheros AR71xx SPI Controller driver version 0.2.4 [ 0.720000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.730000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.730000] m25p80 spi0.1: found mx25l12805d, expected m25p80 [ 0.740000] m25p80 spi0.1: mx25l12805d (16384 Kbytes) [ 0.750000] Concatenating MTD devices: [ 0.750000] (0): "spi0.0" [ 0.750000] (1): "spi0.1" [ 0.760000] into device "flash" [ 0.760000] Creating 7 MTD partitions on "flash": [ 0.760000] 0x000000000000-0x000000040000 : "u-boot" [ 0.770000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.780000] 0x000000050000-0x000000060000 : "art" [ 0.790000] 0x000000060000-0x000000160000 : "kernel" [ 0.800000] 0x000000160000-0x000001ff0000 : "rootfs" [ 0.800000] mtd: partition "rootfs" set to be root filesystem [ 0.810000] mtd: partition "rootfs_data" created automatically, ofs=2C0000, len=1D30000 [ 0.820000] 0x0000002c0000-0x000001ff0000 : "rootfs_data" [ 0.820000] 0x000001ff0000-0x000002000000 : "user_property" [ 0.830000] 0x000000060000-0x000001ff0000 : "firmware" [ 0.990000] ag71xx_mdio: probed [ 0.990000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.760000] eth0: AR8316 switch driver attached. [ 1.780000] ar8316: Using port 4 as switch port [ 2.740000] eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8316/AR8326] [ 2.740000] Atheros AR71xx hardware watchdog driver version 0.1.0 [ 2.740000] ar71xx-wdt: timeout=15 secs (max=21) [ 2.740000] TCP westwood registered [ 2.750000] NET: Registered protocol family 17 [ 2.750000] 802.1Q VLAN Support v1.8 Ben Greear [ 2.760000] All bugs added by David S. Miller [ 2.770000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 2.780000] Freeing unused kernel memory: 184k freed [ 5.310000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0 [ 5.480000] Button Hotplug driver version 0.4.1 [ 5.550000] Registered led device: buffalo:red:diag [ 6.780000] eth0: link up (1000Mbps/Full duplex) [ 8.860000] eth0: link down [ 9.780000] Compat-wireless backport release: compat-wireless-2011-11-29 [ 9.790000] Backport based on wireless-testing.git master-2011-12-01 [ 9.910000] cfg80211: Calling CRDA to update world regulatory domain [ 10.360000] usbcore: registered new interface driver usbfs [ 10.360000] usbcore: registered new interface driver hub [ 10.370000] usbcore: registered new device driver usb [ 10.950000] cfg80211: World regulatory domain updated: [ 10.950000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 10.960000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 10.970000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 10.980000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 10.990000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 10.990000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 11.760000] PCI: Setting latency timer of device 0000:00:00.0 to 64 [ 11.770000] ath: EEPROM regdomain: 0x0 [ 11.770000] ath: EEPROM indicates default country code should be used [ 11.770000] ath: doing EEPROM country->regdmn map search [ 11.770000] ath: country maps to regdmn code: 0x3a [ 11.770000] ath: Country alpha2 being used: US [ 11.770000] ath: Regpair used: 0x3a [ 11.770000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 11.770000] Registered led device: ath9k-phy0 [ 11.770000] Registered led device: buffalo:blue:usb [ 11.770000] Registered led device: buffalo:green:wireless [ 11.770000] Registered led device: buffalo:orange:security [ 11.770000] Registered led device: buffalo:green:router [ 11.770000] Registered led device: buffalo:blue:movie_engine_on [ 11.770000] Registered led device: buffalo:blue:movie_engine_off [ 11.770000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=72 [ 11.790000] cfg80211: Calling CRDA for country: US [ 12.100000] PPP generic driver version 2.4.2 [ 12.110000] cfg80211: Regulatory domain changed to country: US [ 12.110000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 12.120000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 12.130000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 12.140000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 12.150000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 12.150000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 12.160000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 12.280000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 12.430000] NET: Registered protocol family 24 [ 12.620000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.630000] ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller [ 12.630000] ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1 [ 12.670000] ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000 [ 12.690000] ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00 [ 12.690000] hub 1-0:1.0: USB hub found [ 12.700000] hub 1-0:1.0: 1 port detected [ 12.790000] nf_conntrack version 0.5.0 (969 buckets, 3876 max) [ 15.100000] device eth0.1 entered promiscuous mode [ 15.100000] device eth0 entered promiscuous mode [ 16.940000] eth0: link up (1000Mbps/Full duplex) [ 16.940000] br-lan: port 1(eth0.1) entering forwarding state [ 16.950000] br-lan: port 1(eth0.1) entering forwarding state [ 23.470000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 23.490000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 23.490000] jffs2_build_filesystem(): erasing all blocks after the end marker... done. [ 242.390000] JFFS2 notice: (1173) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 243.030000] ar71xx-wdt: enabling watchdog timer

On the WZR-300HP, Pin 1 does not supply +3.3V. There is a 0 K resistor right next to pin one which can be bridged to complete the +3.3V circuit. Unfortunately, it is covered in solder now, but I believe that it was labeled R347 on the silk screen. Once this is completed, the serial console will function. If you are using a USB TTL cable, this may not be necessary.

* If you see the diag light flash twice about every 2-3 seconds, it means the flashing did not work properly. I did a TFTP recovery using the factory firmware ( I count exactly 10 seconds from power on before sending the TFTP File ), and it flashed. ( remember to wait 5-6 minutes after a tftp recovery ).

WZR-HP-G302H is Japanese market name for WZR-HP-G300NH2, and seems to have slightly different WiFi chip, Atheros AR9283-AL1A. It is very probable that WZR-HP-G302H A1A0 and WZR-HP-G302H A1A0 have an identical motherboar inside, as both have dual 16MiB SPI flash chips just like WZR-HP-AG300H, with erase size of 64k. This means default WZR-HP-G300NH2 jffs2 image will not work correctly (one can fix this by modifying target/linux/ar71xx/image/Makefile, search for WZR-HP-G300NH2 profile and change fs_128k to fs_64k). WZR-HP-G302H A1A0 motherboard silk-print label says:

WZR-HP-G302HV2
21514W302HV21A2 Rev:A2

Similarly to Japanese variant of WZR-HP-G300NH, A1A0 comes with locked buffalo u-boot v1.08 (based on U-Boot 1.1.4 for BUFFALO AIRSTATION, PB93), see http://wiki.openwrt.org/toh/buffalo/wzr-hp-g300h#locked.u-boot.too.short.time.tftp.window for details. Furthermore, this newest buffalo u-boot BS does not even provide serial console at boot time! But TFTP "blind" flash to OpenWRT was possible when accept_open_rt_fmt=1 was set (tested and confirmed ok with r31678 squashfs, try it at your own risk). Also, it is possible to circumvent serial console lock by setting force_uart variable in a similar manner to accept_open_rt_fmt.

In addition, proper fw_env.config for uboot-envtools for A1A0 variant is:

#MTD device name        Device offset   Env. size       Flash sector size
/dev/mtd0               0x40000         0x10000         0x10000

Here is the WZR-HP-G302H boot log of jffs2 image with unlocked serial and fs_64k:

In: serial Out: serial Err: serial Memory Test uboot use 83F6BFB0 - 84000000 Memory Test start(80000000) end(83F00000) size(03F00000) Pattern 55555555 Writing... Reading... Pattern AAAAAAAA Writing... Reading... Pattern 00000000 Writing... Reading... Memory Test OK ### buf_ver=[1.08] U-Boot Ver.=[1.08] ### build_date(env)=[Sep 26 2011 - 00:19:46] build_date(bin)=[Sep 26 2011 - 00:19:46] ag7240_enet_initialize... Reading MAC Address from ENV(0x83f8c2f8) No valid address in Flash. Using fixed address Virian MDC CFG Value ==> 4 : cfg1 0x7 cfg2 0x7014 eth0: 02:aa:bb:cc:dd:1a eth0 up Virian MDC CFG Value ==> 4 : cfg1 0xf cfg2 0x7214 eth1: 00:03:7f:09:0b:ad ATHRS26: resetting s26 ATHRS26: s26 reset done eth1 up eth0 02:AA:BB:CC:DD:1A , eth1 00:03:7F:09:0B:AD dup 1 speed 1000 tftp server(receive) go, waiting:4[sec] Load address: 0x81f00000 TftpServer Timeout; no file was loaded. change bootargs console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@320k(ART),64k@8128k(properties) mem=64M product_rev=1 UART=1 ## Booting image at bf060000 ... Image Name: MIPS OpenWrt Linux-3.3.6 Created: 2012-05-24 6:25:32 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 901567 Bytes = 880.4 kB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum ... crc32_fw: bf060040 - bf13c1fe (len:000dc1bf) calc... crc32_fw: range1 bf060040 - bf13c1fe OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ... [ 0.000000] Linux version 3.3.6 (zgembo@buildhost) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Thu May 24 15:25:10 JST 2012 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR7242 rev 1 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=WZR-HP-G300NH2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61800k/65536k available (2072k kernel code, 3736k reserved, 389k data, 200k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:48 [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.090000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79 [ 0.100000] MIPS: machine is Buffalo WZR-HP-G300NH2 [ 0.330000] registering PCI controller with io_map_base unset [ 0.340000] bio: create slab at 0 [ 0.350000] PCI host bridge to bus 0000:00 [ 0.350000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff] [ 0.360000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.360000] pci 0000:00:00.0: fixup device configuration [ 0.370000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit] [ 0.370000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.380000] Switching to clocksource MIPS [ 0.380000] NET: Registered protocol family 2 [ 0.390000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.390000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.400000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.400000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.410000] TCP reno registered [ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.420000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.430000] NET: Registered protocol family 1 [ 0.450000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.450000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.470000] msgmni has been set to 120 [ 0.470000] io scheduler noop registered [ 0.470000] io scheduler deadline registered (default) [ 0.480000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.510000] console [ttyS0] enabled, bootconsole disabled [ 0.510000] console [ttyS0] enabled, bootconsole disabled [ 0.530000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.530000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.540000] m25p80 spi0.1: found mx25l12805d, expected m25p80 [ 0.550000] m25p80 spi0.1: mx25l12805d (16384 Kbytes) [ 0.550000] Concatenating MTD devices: [ 0.560000] (0): "spi0.0" [ 0.560000] (1): "spi0.1" [ 0.560000] into device "flash" [ 0.570000] Creating 7 MTD partitions on "flash": [ 0.580000] 0x000000000000-0x000000040000 : "u-boot" [ 0.580000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.590000] 0x000000050000-0x000000060000 : "art" [ 0.600000] 0x000000060000-0x000000160000 : "kernel" [ 0.600000] 0x000000160000-0x000001ff0000 : "rootfs" [ 0.610000] mtd: partition "rootfs" set to be root filesystem [ 0.620000] split_squashfs: no squashfs found in "flash" [ 0.620000] 0x000001ff0000-0x000002000000 : "user_property" [ 0.630000] 0x000000060000-0x000001ff0000 : "firmware" [ 0.640000] ag71xx_mdio: probed [ 0.650000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.230000] eth0: AR8316 switch driver attached. [ 1.230000] ar8316: Using port 4 as switch port [ 1.330000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316] [ 1.350000] TCP westwood registered [ 1.350000] NET: Registered protocol family 17 [ 1.350000] 8021q: 802.1Q VLAN Support v1.8 [ 3.290000] JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 3.310000] VFS: Mounted root (jffs2 filesystem) readonly on device 31:6. [ 3.320000] Freeing unused kernel memory: 200k freed - preinit - Press the [f] key and hit [enter] to enter failsafe mode [ 7.330000] eth0: link up (1000Mbps/Full duplex) - regular preinit - - init - [ 9.540000] eth0: link down Please press Enter to activate this console. [ 10.110000] usbcore: registered new interface driver usbfs [ 10.120000] usbcore: registered new interface driver hub [ 10.130000] usbcore: registered new device driver usb [ 10.180000] loop: module loaded [ 10.250000] PPP generic driver version 2.4.2 [ 10.340000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.480000] NET: Registered protocol family 24 [ 10.580000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 10.580000] ehci-platform ehci-platform: Generic Platform EHCI Controller [ 10.590000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 10.630000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 10.650000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 10.650000] hub 1-0:1.0: USB hub found [ 10.660000] hub 1-0:1.0: 1 port detected [ 10.730000] nf_conntrack version 0.5.0 (968 buckets, 3872 max) [ 13.600000] device eth0.1 entered promiscuous mode [ 13.600000] device eth0 entered promiscuous mode [ 14.340000] eth0: link up (1000Mbps/Full duplex) [ 14.360000] br-lan: port 1(eth0.1) entered forwarding state [ 14.370000] br-lan: port 1(eth0.1) entered forwarding state [ 14.410000] br-lan: port 1(eth0.1) entered disabled state [ 14.410000] device eth0.1 left promiscuous mode [ 14.420000] device eth0 left promiscuous mode [ 14.420000] br-lan: port 1(eth0.1) entered disabled state [ 14.510000] device eth0.1 entered promiscuous mode [ 14.510000] device eth0 entered promiscuous mode [ 14.540000] br-lan: port 1(eth0.1) entered forwarding state [ 14.550000] br-lan: port 1(eth0.1) entered forwarding state [ 16.550000] br-lan: port 1(eth0.1) entered forwarding state BusyBox v1.19.4 (2012-05-23 21:35:24 JST) built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- ATTITUDE ADJUSTMENT (Bleeding Edge, r31835) ----------------------------------------------------- * 1/4 oz Vodka Pour all ingredients into mixing * 1/4 oz Gin tin with ice, strain into glass. * 1/4 oz Amaretto * 1/4 oz Triple sec * 1/4 oz Peach schnapps * 1/4 oz Sour mix * 1 splash Cranberry juice ----------------------------------------------------- root@OpenWrt:/#

This board, marked WZR-HP-G302HV2 Rev: A3, is nearly identical to the other revisions, and the same image appears to flash successfully. A visual inspection shows a different DDR2 module (both Nanya, but it looks like the previous chip was EOL'd), various capacitors in different positions, and a coil on the back of the board is covered in epoxy now.

BUFFALO U-BOOT Ver 1.00 == CPU:400MHz, DDR:400MHz, AHB:200MHz == PB93 (ar7241 - Virian) U-boot DRAM: 64 MB WAN port disabling: done Top of RAM usable for U-Boot at: 84000000 Reserving 267k for U-Boot at: 83fbc000 Reserving 192k for malloc() at: 83f8c000 Reserving 44 Bytes for Board Info at: 83f8bfd4 Reserving 36 Bytes for Global Data at: 83f8bfb0 Reserving 128k for boot params() at: 83f6bfb0 Stack Pointer at: 83f6bf98 Now running in RAM - U-Boot at: 83fbc000 flash bank #0 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256] flash bank #1 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256] Flash: 32 MB In: serial Out: serial Err: serial Memory Test uboot use 83F6BFB0 - 84000000 Memory Test start(80000000) end(83F00000) size(03F00000) Pattern 00000000 Writing... Reading... Memory Test OK ### buf_ver=[1.00] U-Boot Ver.=[1.00] ### build_date(env)=[May 21 2012 - 06:39:59] build_date(bin)=[May 21 2012 - 06:39:59] ag7240_enet_initialize... Reading MAC Address from ENV(0x83f8c2f8) No valid address in Flash. Using fixed address Virian MDC CFG Value ==> 4 : cfg1 0x7 cfg2 0x7014 eth0: 02:aa:bb:cc:dd:1a eth0 up Virian MDC CFG Value ==> 4 : cfg1 0xf cfg2 0x7214 eth1: 00:03:7f:09:0b:ad ATHRS26: resetting s26 ATHRS26: s26 reset done eth1 up eth0 02:AA:BB:CC:DD:1A , eth1 00:03:7F:09:0B:AD dup 1 speed 1000 tftp server(receive) go, waiting:4[sec] Load address: 0x81f00000 $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ tftp server done Bytes transferred = 2949156 (2d0024 hex) Airstation Public header Recv fw image [2949124] bytes, now writing... flash-addr 0xBF060000 - 0xBF33FFFF search sector 0xbf060000 - 0xbf33ffff BANK #1 (6 : 51) 000 PPPP.Poooooooooooooooooooooooooo 032 oooooooooooooooooooo............ 064 ................................ 096 ................................ 128 ................................ 160 ................................ 192 ................................ 224 ................................ BANK #2 (-1 : -1) 000 ................................ 032 ................................ 064 ................................ 096 ................................ 128 ................................ 160 ................................ 192 ................................ 224 ................................ First 0x6 last 0x33 sector size 0x10000 51 Erased 46 sectors Copy to Flash... Copy 2949124 byte to Flash... write data: 81f00020 --> bf060000 (len:2d0004) done change bootargs console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@320k(ART),64k@8128k(properties) mem=64M product_rev=1 UART=1 ## Booting image at bf060000 ... Image Name: MIPS OpenWrt Linux-3.3.8 Created: 2012-11-18 4:37:08 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 955998 Bytes = 933.6 kB Load Address: 80060000 Entry Point: 80060000 Verifying Checksum ... crc32_fw: bf060040 - bf14969d (len:000e965e) calc... crc32_fw: range1 bf060040 - bf14969d OK Uncompressing Kernel Image ... OK Ethernet Disabled! No initrd ## Transferring control to Linux (at address 80060000) ... ## Giving linux memsize in bytes, 67108864 Starting kernel ... [ 0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Nov 18 04:31:55 UTC 2012 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR7242 rev 1 [ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=WZR-HP-G300NH2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61496k/65536k available (2209k kernel code, 4040k reserved, 412k data, 212k init, 0k highmem) [ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] NET: Registered protocol family 16 [ 0.090000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79 [ 0.100000] MIPS: machine is Buffalo WZR-HP-G300NH2 [ 0.330000] registering PCI controller with io_map_base unset [ 0.340000] bio: create slab at 0 [ 0.350000] PCI host bridge to bus 0000:00 [ 0.350000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff] [ 0.360000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.360000] pci 0000:00:00.0: fixup device configuration [ 0.370000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit] [ 0.370000] pci 0000:00:00.0: using irq 40 for pin 1 [ 0.380000] Switching to clocksource MIPS [ 0.380000] NET: Registered protocol family 2 [ 0.390000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.390000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.400000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.400000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.410000] TCP reno registered [ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.420000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.430000] NET: Registered protocol family 1 [ 0.450000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.450000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.470000] msgmni has been set to 120 [ 0.470000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.480000] io scheduler noop registered [ 0.480000] io scheduler deadline registered (default) [ 0.490000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.520000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.530000] console [ttyS0] enabled, bootconsole disabled [ 0.530000] console [ttyS0] enabled, bootconsole disabled [ 0.540000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.550000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.550000] m25p80 spi0.1: found mx25l12805d, expected m25p80 [ 0.560000] m25p80 spi0.1: mx25l12805d (16384 Kbytes) [ 0.570000] Concatenating MTD devices: [ 0.570000] (0): "spi0.0" [ 0.570000] (1): "spi0.1" [ 0.580000] into device "flash" [ 0.590000] Creating 7 MTD partitions on "flash": [ 0.590000] 0x000000000000-0x000000040000 : "u-boot" [ 0.600000] 0x000000040000-0x000000050000 : "u-boot-env" [ 0.600000] 0x000000050000-0x000000060000 : "art" [ 0.610000] 0x000000060000-0x000000160000 : "kernel" [ 0.620000] 0x000000160000-0x000001ff0000 : "rootfs" [ 0.620000] mtd: partition "rootfs" set to be root filesystem [ 0.630000] mtd: partition "rootfs_data" created automatically, ofs=330000, len=1CC0000 [ 0.640000] 0x000000330000-0x000001ff0000 : "rootfs_data" [ 0.650000] 0x000001ff0000-0x000002000000 : "user_property" [ 0.650000] 0x000000060000-0x000001ff0000 : "firmware" [ 0.660000] ag71xx_mdio: probed [ 0.670000] eth0: Atheros AG71xx at 0xb9000000, irq 4 [ 1.250000] eth0: Atheros AR8316 switch driver attached. [ 1.250000] ar8316: Using port 4 as switch port [ 1.350000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316] [ 1.370000] TCP cubic registered [ 1.370000] NET: Registered protocol family 17 [ 1.370000] Bridge firewalling registered [ 1.380000] 8021q: 802.1Q VLAN Support v1.8 [ 1.390000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 1.400000] Freeing unused kernel memory: 212k freed - preinit - Press the [f] key and hit [enter] to enter failsafe mode [ 5.350000] eth0: link up (1000Mbps/Full duplex) - regular preinit - jffs2 not ready yet; using ramdisk - init - [ 7.130000] eth0: link down [ 9.150000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993 [ 9.150000] Backport based on wireless-testing.git master-2012-09-07 [ 9.160000] compat.git: wireless-testing.git [ 9.190000] cfg80211: Calling CRDA to update world regulatory domain [ 9.200000] cfg80211: World regulatory domain updated: [ 9.200000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 9.210000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.220000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 9.230000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 9.240000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.240000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 9.650000] usbcore: registered new interface driver usbfs [ 9.660000] usbcore: registered new interface driver hub [ 9.670000] usbcore: registered new device driver usb [ 10.400000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 10.420000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40 [ 10.430000] cfg80211: Calling CRDA for country: US [ 10.440000] cfg80211: Regulatory domain changed to country: US [ 10.440000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 10.450000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 10.460000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 10.470000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 10.470000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 10.480000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 10.490000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 10.540000] PPP generic driver version 2.4.2 [ 10.800000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.020000] NET: Registered protocol family 24 [ 11.040000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 11.050000] ehci-platform ehci-platform: Generic Platform EHCI Controller [ 11.050000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 [ 11.090000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000 [ 11.110000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 [ 11.110000] hub 1-0:1.0: USB hub found [ 11.120000] hub 1-0:1.0: 1 port detected [ 11.140000] nf_conntrack version 0.5.0 (964 buckets, 3856 max) [ 11.370000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Please press Enter to activate this console. [ 15.220000] device eth0.1 entered promiscuous mode [ 15.220000] device eth0 entered promiscuous mode [ 16.390000] eth0: link up (1000Mbps/Full duplex) [ 16.400000] br-lan: port 1(eth0.1) entered forwarding state [ 16.400000] br-lan: port 1(eth0.1) entered forwarding state [ 18.400000] br-lan: port 1(eth0.1) entered forwarding state [ 25.930000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 25.930000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 25.940000] jffs2_build_filesystem(): erasing all blocks after the end marker...