Differences

This shows you the differences between two versions of the page.

--- toh:buffalo:wzr-hp-g300nh2 [2012/12/06 03:02]
+++ toh:buffalo:wzr-hp-g300nh2 [2015/12/14 11:25] (current)
tmomas New bootlog formatting applied
@@ Line 1: / Line 1: @@
+====== Buffalo WZR-HP-G300NH2 / WZR-300HP ======
+===== Supported Versions =====
+^ Version/Model              ^ Launch Date   ^ S/N   ^ OpenWrt Version Supported   ^ Model Specific Notes                                               ^
+| A0A0, A0A1                 | 2011-08   | -   | since [[https://dev.openwrt.org/changeset/29568|r29568]]   | -                                         |
+| A0A3 (sold as WZR-300HP)   | ?         | -   | Barrier Breaker                   | Japanese model                                                     |
+| A1A0                       | 2011-11   | -   | since r31678 or earlier?          | squashfs should work, jffs2 need flash erase size set to 64k       |
+| B0A0 (marked WZR-300HP)    | 2012-11   | -   | Attitude Adjustment               | squashfs works, have not tested jffs2                              |
+| B0A1 (sold as WZR-300HP)   | ?         | -   | Barrier Breaker Snapshot r39382   | Might Work: See https://forum.openwrt.org/viewtopic.php?id=44009   |
+| C1A0                       | ???       | -   | r37793 or earlier?                | squashfs works, have not tested jffs2                              |
+===== Hardware Highlights =====
+^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^
+| Atheros AR7242@400MHz | 64MiB | 32MiB | 4 x 1| Yes | Yes - no header | https://forum.openwrt.org/viewtopic.php?id=34993 ??? |
+Lan Port Mappings for /etc/config/network
+^ Hardware Port   ^ Logical port   ^ LuCI Label   ^ Description                                  ^
+| NA              | 0              | 1            | CPU port activates/links all ports on Vlan   |
+| 1               | 1              | 2            | Activates the #1 LAN port                    |
+| 2               | 5              | CPU          | Activates the #2 LAN port                    |
+| 3               | 4              | 5            | Activates the #3 LAN port                    |
+| 4               | 3              | 4            | Activates the #4 LAN port                    |
+| WAN             | 2              | 3            | Activates the WAN/Internet port              |
+==== Info ====
+| **Architecture:**     | MIPS                   |
+| **Vendor:**           | Atheros                |
+| **Bootloader:**       | U-Boot                 |
+| **System-On-Chip:**   | Atheros AR7242 rev 1   |
+| **CPU/Speed**         | 400 Mhz (MIPS 24Kc)    |
+| **Flash-Chip:**   | [[http://dl.dropbox.com/u/38634684/openwrt/MX25L12845EZNI-10G.pdf|Macronix MX25L128-45E (x2)]] |
+| **Flash size:**   | 32 MiB                                        |
+| **RAM:**          | 64 MiB                                        |
+| **Wireless:**     | Atheros AR9280 Rev:2                          |
+| **Ethernet:**     | AG71xx ethernet with AR8316 switch and vlan   |
+| **USB:**          | Yes 1 x 2.0 (ehci)                            |
+| **Serial:**       | [[#Serial|Yes]]                               |
+==== Flash procedure ====
+To flash the WZR-HP-G300NH2, follow the same procedure as the [[toh/buffalo/wzr-hp-g300h]], but use 02:AA:BB:CC:DD:1A for the static arp entry. Download the latest image here: [[http://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/openwrt-ar71xx-generic-wzr-hp-g300nh2-squashfs-tftp.bin | Stable release]] ( <color red>Flashing Backfire to this router will brick the router</color> ( solid red light ) as this version has a new ethernet driver ).
+As noted under [[https://forum.openwrt.org/viewtopic.php?pid=176220#p176220 | forum post #452 ]] **current fimwares sometimes don't show the correct LED status (due to a bug)**. This means the flash might appear to have failed (solid red light) but instead was successful. After any flash it is therefore recommended to follow [[:doc:howto:firstlogin | the normal first login instructions]] regardless of LED status.
+==== Boot Log ====
+<WRAP bootlog>
+<nowiki>BUFFALO U-BOOT Ver 1.03
+  == CPU:400MHz, DDR:400MHz, AHB:200MHz ==
+PB93 (ar7241 - Virian) U-boot
+DRAM:  64 MB
+WAN port disabling: done
+Top of RAM usable for U-Boot at: 84000000
+Reserving 265k for U-Boot at: 83fbc000
+Reserving 192k for malloc() at: 83f8c000
+Reserving 44 Bytes for Board Info at: 83f8bfd4
+Reserving 36 Bytes for Global Data at: 83f8bfb0
+Reserving 128k for boot params() at: 83f6bfb0
+Stack Pointer at: 83f6bf98
+Now running in RAM - U-Boot at: 83fbc000
+flash bank #0 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256]
+flash bank #1 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256]
+Flash: 32 MB
+In:    serial
+Out:   serial
+Err:   serial
+Memory Test
+uboot use  83F6BFB0 - 84000000
+Memory Test start(80000000) end(83F00000) size(03F00000)
+Pattern 00000000  Writing...  Reading...
+Memory Test OK
+### buf_ver=[1.03] U-Boot Ver.=[1.03]
+### build_date(env)=[Mar  7 2011 - 05:27:46] build_date(bin)=[Mar  7 2011 - 05:27:46]
+ag7240_enet_initialize...
+Reading MAC Address from ENV(0x83f8c322)
+No valid address in Flash. Using fixed address
+Virian MDC CFG Value ==> 4
+: cfg1 0x7 cfg2 0x7014
+eth0: 02:aa:bb:cc:dd:1a
+eth0 up
+Virian MDC CFG Value ==> 4
+: cfg1 0xf cfg2 0x7214
+eth1: 00:03:7f:09:0b:ad
+ATHRS26: resetting s26
+ATHRS26: s26 reset done
+eth1 up
+eth0  02:AA:BB:CC:DD:1A
+, eth1  00:03:7F:09:0B:AD
+dup 1 speed 1000
+tftp server(receive) go, waiting:4[sec]
+Load address: 0x81f00000
+$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+tftp server done
+Bytes transferred = 2621476 (280024 hex)
+Airstation Public header
+Recv fw image [2621444] bytes, now writing...
+flash-addr 0xBF060000 - 0xBF2EFFFF
+search sector 0xbf060000 - 0xbf2effff
+BANK #1 (6 : 46)
+  PPPP.Poooooooooooooooooooooooooo
+  ooooooooooooooo.................
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+BANK #2 (-1 : -1)
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+First 0x6 last 0x2e sector size 0x10000
+Erased 41 sectors
+Copy to Flash...
+ Copy 2621444 byte to Flash...
+write data: 81f00020 --> bf060000  (len:280004)
+done
+change bootargs
+console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@320k(ART),64k@8128k(properties),8192k@8192k(flash1),16384k@16384k(flash2) mem=64M product_rev=1
+## Booting image at bf060000 ...
+   Image Name:   MIPS OpenWrt Linux-2.6.39.4
+   Created:      2011-12-15  18:39:27 UTC
+   Image Type:   MIPS Linux Kernel Image (lzma compressed)
+   Data Size:    871284 Bytes = 850.9 kB
+   Load Address: 80060000
+   Entry Point:  80060000
+   Verifying Checksum ... crc32_fw: bf060040 - bf134bb3 (len:000d4b74) calc...
+crc32_fw: range1 bf060040 - bf134bb3
+OK
+   Uncompressing Kernel Image ... OK
+No initrd
+## Transferring control to Linux (at address 80060000) ...
+## Giving linux memsize in bytes, 67108864
+Starting kernel ...
+[    0.000000] Linux version 2.6.39.4 (mdeneen@build) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Thu Dec 15 13:39:21 EST 2011
+[    0.000000] prom: fw_arg0=00000008, fw_arg1=a3f6bfb0, fw_arg2=a3f6c4b0, fw_arg3=00000020
+[    0.000000] MyLoader: sysp=00000000, boardp=00000000, parts=00000000
+[    0.000000] bootconsole [early0] enabled
+[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
+[    0.000000] SoC: Atheros AR7242 rev 1
+[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
+[    0.000000] Determined physical RAM map:
+[    0.000000]  memory: 04000000 @ 00000000 (usable)
+[    0.000000] Initrd not found or empty - disabling initrd
+[    0.000000] Zone PFN ranges:
+[    0.000000]   Normal   0x00000000 -> 0x00004000
+[    0.000000] Movable zone start PFN for each node
+[    0.000000] early_node_map[1] active PFN ranges
+[    0.000000]     0: 0x00000000 -> 0x00004000
+[    0.000000] On node 0 totalpages: 16384
+[    0.000000] free_area_init_node: node 0, pgdat 802b9570, node_mem_map 81000000
+[    0.000000]   Normal zone: 128 pages used for memmap
+[    0.000000]   Normal zone: 0 pages reserved
+[    0.000000]   Normal zone: 16256 pages, LIFO batch:3
+[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
+[    0.000000] pcpu-alloc: [0] 0
+[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
+[    0.000000] Kernel command line:  board=WZR-HP-G300NH2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
+[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
+[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
+[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
+[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
+[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
+[    0.000000] Writing ErrCtl register=00000000
+[    0.000000] Readback ErrCtl register=00000000
+[    0.000000] Memory: 61848k/65536k available (2013k kernel code, 3688k reserved, 393k data, 184k init, 0k highmem)
+[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
+[    0.000000] NR_IRQS:80
+[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
+[    0.080000] pid_max: default: 32768 minimum: 301
+[    0.080000] Mount-cache hash table entries: 512
+[    0.090000] NET: Registered protocol family 16
+[    0.100000] MIPS: machine is Buffalo WZR-HP-G300NH2
+[    0.100000] ar71xx: pll_reg 0xb805002c: 0x62000000
+[    0.530000] registering PCI controller with io_map_base unset
+[    0.540000] bio: create slab <bio-0> at 0
+[    0.550000] pci 0000:00:00.0: [168c:ff1c] type 0 class 0x000200
+[    0.550000] pci 0000:00:00.0: fixup device configuration
+[    0.550000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x0000ffff 64bit]
+[    0.550000] pci 0000:00:00.0: supports D1
+[    0.550000] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
+[    0.550000] pci 0000:00:00.0: PME# disabled
+[    0.550000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
+[    0.560000] pci 0000:00:00.0: BAR 0: set to [mem 0x10000000-0x1000ffff 64bit] (PCI address [0x10000000-0x1000ffff])
+[    0.570000] PCI: mapping irq 72 to pin1@0000:00:00.0
+[    0.570000] Switching to clocksource MIPS
+[    0.580000] NET: Registered protocol family 2
+[    0.580000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
+[    0.580000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
+[    0.590000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
+[    0.590000] TCP: Hash tables configured (established 2048 bind 2048)
+[    0.600000] TCP reno registered
+[    0.600000] UDP hash table entries: 256 (order: 0, 4096 bytes)
+[    0.610000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
+[    0.610000] NET: Registered protocol family 1
+[    0.620000] PCI: CLS 0 bytes, default 32
+[    0.640000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
+[    0.640000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
+[    0.650000] msgmni has been set to 120
+[    0.660000] io scheduler noop registered
+[    0.660000] io scheduler deadline registered (default)
+[    0.670000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
+[    0.690000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
+[    0.700000] console [ttyS0] enabled, bootconsole disabled
+[    0.710000] Atheros AR71xx SPI Controller driver version 0.2.4
+[    0.720000] m25p80 spi0.0: found mx25l12805d, expected m25p80
+[    0.730000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
+[    0.730000] m25p80 spi0.1: found mx25l12805d, expected m25p80
+[    0.740000] m25p80 spi0.1: mx25l12805d (16384 Kbytes)
+[    0.750000] Concatenating MTD devices:
+[    0.750000] (0): "spi0.0"
+[    0.750000] (1): "spi0.1"
+[    0.760000] into device "flash"
+[    0.760000] Creating 7 MTD partitions on "flash":
+[    0.760000] 0x000000000000-0x000000040000 : "u-boot"
+[    0.770000] 0x000000040000-0x000000050000 : "u-boot-env"
+[    0.780000] 0x000000050000-0x000000060000 : "art"
+[    0.790000] 0x000000060000-0x000000160000 : "kernel"
+[    0.800000] 0x000000160000-0x000001ff0000 : "rootfs"
+[    0.800000] mtd: partition "rootfs" set to be root filesystem
+[    0.810000] mtd: partition "rootfs_data" created automatically, ofs=2C0000, len=1D30000
+[    0.820000] 0x0000002c0000-0x000001ff0000 : "rootfs_data"
+[    0.820000] 0x000001ff0000-0x000002000000 : "user_property"
+[    0.830000] 0x000000060000-0x000001ff0000 : "firmware"
+[    0.990000] ag71xx_mdio: probed
+[    0.990000] eth0: Atheros AG71xx at 0xb9000000, irq 4
+[    1.760000] eth0: AR8316 switch driver attached.
+[    1.780000] ar8316: Using port 4 as switch port
+[    2.740000] eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8316/AR8326]
+[    2.740000] Atheros AR71xx hardware watchdog driver version 0.1.0
+[    2.740000] ar71xx-wdt: timeout=15 secs (max=21)
+[    2.740000] TCP westwood registered
+[    2.750000] NET: Registered protocol family 17
+[    2.750000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
+[    2.760000] All bugs added by David S. Miller <davem@redhat.com>
+[    2.770000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
+[    2.780000] Freeing unused kernel memory: 184k freed
+[    5.310000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
+[    5.480000] Button Hotplug driver version 0.4.1
+[    5.550000] Registered led device: buffalo:red:diag
+[    6.780000] eth0: link up (1000Mbps/Full duplex)
+[    8.860000] eth0: link down
+[    9.780000] Compat-wireless backport release: compat-wireless-2011-11-29
+[    9.790000] Backport based on wireless-testing.git master-2011-12-01
+[    9.910000] cfg80211: Calling CRDA to update world regulatory domain
+[   10.360000] usbcore: registered new interface driver usbfs
+[   10.360000] usbcore: registered new interface driver hub
+[   10.370000] usbcore: registered new device driver usb
+[   10.950000] cfg80211: World regulatory domain updated:
+[   10.950000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
+[   10.960000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[   10.970000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
+[   10.980000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
+[   10.990000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[   10.990000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[   11.760000] PCI: Setting latency timer of device 0000:00:00.0 to 64
+[   11.770000] ath: EEPROM regdomain: 0x0
+[   11.770000] ath: EEPROM indicates default country code should be used
+[   11.770000] ath: doing EEPROM country->regdmn map search
+[   11.770000] ath: country maps to regdmn code: 0x3a
+[   11.770000] ath: Country alpha2 being used: US
+[   11.770000] ath: Regpair used: 0x3a
+[   11.770000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
+[   11.770000] Registered led device: ath9k-phy0
+[   11.770000] Registered led device: buffalo:blue:usb
+[   11.770000] Registered led device: buffalo:green:wireless
+[   11.770000] Registered led device: buffalo:orange:security
+[   11.770000] Registered led device: buffalo:green:router
+[   11.770000] Registered led device: buffalo:blue:movie_engine_on
+[   11.770000] Registered led device: buffalo:blue:movie_engine_off
+[   11.770000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=72
+[   11.790000] cfg80211: Calling CRDA for country: US
+[   12.100000] PPP generic driver version 2.4.2
+[   12.110000] cfg80211: Regulatory domain changed to country: US
+[   12.110000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
+[   12.120000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
+[   12.130000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
+[   12.140000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[   12.150000] cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[   12.150000] cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[   12.160000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
+[   12.280000] ip_tables: (C) 2000-2006 Netfilter Core Team
+[   12.430000] NET: Registered protocol family 24
+[   12.620000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
+[   12.630000] ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
+[   12.630000] ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
+[   12.670000] ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
+[   12.690000] ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
+[   12.690000] hub 1-0:1.0: USB hub found
+[   12.700000] hub 1-0:1.0: 1 port detected
+[   12.790000] nf_conntrack version 0.5.0 (969 buckets, 3876 max)
+[   15.100000] device eth0.1 entered promiscuous mode
+[   15.100000] device eth0 entered promiscuous mode
+[   16.940000] eth0: link up (1000Mbps/Full duplex)
+[   16.940000] br-lan: port 1(eth0.1) entering forwarding state
+[   16.950000] br-lan: port 1(eth0.1) entering forwarding state
+[   23.470000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
+[   23.490000] jffs2_build_filesystem(): unlocking the mtd device... done.
+[   23.490000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
+[  242.390000] JFFS2 notice: (1173) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
+[  243.030000] ar71xx-wdt: enabling watchdog timer</nowiki>
+</WRAP>\\
+==== Photos ====
+{{:media:buffalo:g300nh_a2.png?320x240&direct|Front PCB, ver2 A1 A0}}
+{{:media:buffalo:g300nh_a2_serial_port.png?320x240&direct|Serial port on PCB ver2 A1 A0}}
+===== Serial =====
+| **Pin 1**   | VCC +3.3V      |
+| **Pin 2**   | GND            |
+| **Pin 3**   | TX             |
+| **Pin 4**   | RX             |
+| Settings    | 115200,8,N,1   |
+On the WZR-300HP, Pin 1 does not supply +3.3V.  There is a 0 K resistor right next to pin one which can be bridged to complete the +3.3V circuit.  Unfortunately, it is covered in solder now, but I believe that it was labeled R347 on the silk screen.  Once this is completed, the serial console will function.  If you are using a USB TTL cable, this may not be necessary.
+===== Two flashes of diag every few seconds =====
+ * If you see the diag light flash twice about every 2-3 seconds, it means the flashing did not work properly. I did a TFTP recovery using the factory firmware ( I count exactly 10 seconds from power on before sending the TFTP File ), and it flashed. ( remember to wait 5-6 minutes after a tftp recovery ).
+===== Revision A1A0 and WZR-HP-G302H A1A0 (Japanese variant) =====
+WZR-HP-G302H is Japanese market name for WZR-HP-G300NH2, and seems to have slightly different WiFi chip, Atheros AR9283-AL1A. It is very probable that WZR-HP-G302H A1A0 and WZR-HP-G302H A1A0 have an identical motherboar inside, as both have dual 16MiB SPI flash chips just like WZR-HP-AG300H, with erase size of 64k. This means default WZR-HP-G300NH2 jffs2 image will not work correctly (one can fix this by modifying target/linux/ar71xx/image/Makefile, search for WZR-HP-G300NH2 profile and change fs_128k to fs_64k). WZR-HP-G302H A1A0 motherboard silk-print label says:
+  WZR-HP-G302HV2
+W302HV21A2 Rev:A2
+Similarly to Japanese variant of WZR-HP-G300NH, A1A0 comes with locked buffalo u-boot v1.08 (based on U-Boot 1.1.4 for BUFFALO AIRSTATION, PB93), see http://wiki.openwrt.org/toh/buffalo/wzr-hp-g300h#locked.u-boot.too.short.time.tftp.window for details. Furthermore, this newest buffalo u-boot BS does not even provide serial console at boot time! But TFTP "blind" flash to OpenWRT was possible when accept_open_rt_fmt=1 was set (tested and confirmed ok with r31678 squashfs, try it at your own risk). Also, it is possible to circumvent serial console lock by setting force_uart variable in a similar manner to accept_open_rt_fmt.
+In addition, proper fw_env.config for uboot-envtools for A1A0 variant is:
+  #MTD device name        Device offset   Env. size       Flash sector size
+  /dev/mtd0               0x40000         0x10000         0x10000
+Here is the WZR-HP-G302H boot log of jffs2 image with unlocked serial and fs_64k:
+<WRAP bootlog>
+<nowiki>In:    serial
+Out:   serial
+Err:   serial
+Memory Test
+uboot use  83F6BFB0 - 84000000
+Memory Test start(80000000) end(83F00000) size(03F00000)
+Pattern 55555555  Writing...            Reading...
+Pattern AAAAAAAA  Writing...            Reading...
+Pattern 00000000  Writing...            Reading...
+Memory Test OK
+### buf_ver=[1.08] U-Boot Ver.=[1.08]
+### build_date(env)=[Sep 26 2011 - 00:19:46] build_date(bin)=[Sep 26 2011 - 00:19:46]
+ag7240_enet_initialize...
+Reading MAC Address from ENV(0x83f8c2f8)
+No valid address in Flash. Using fixed address
+Virian MDC CFG Value ==> 4
+: cfg1 0x7 cfg2 0x7014
+eth0: 02:aa:bb:cc:dd:1a
+eth0 up
+Virian MDC CFG Value ==> 4
+: cfg1 0xf cfg2 0x7214
+eth1: 00:03:7f:09:0b:ad
+ATHRS26: resetting s26
+ATHRS26: s26 reset done
+eth1 up
+eth0  02:AA:BB:CC:DD:1A
+, eth1  00:03:7F:09:0B:AD
+dup 1 speed 1000
+tftp server(receive) go, waiting:4[sec]
+Load address: 0x81f00000
+TftpServer Timeout;
+no file was loaded.
+change bootargs
+console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@320k(ART),64k@8128k(properties) mem=64M product_rev=1 UART=1
+## Booting image at bf060000 ...
+   Image Name:   MIPS OpenWrt Linux-3.3.6
+   Created:      2012-05-24   6:25:32 UTC
+   Image Type:   MIPS Linux Kernel Image (lzma compressed)
+   Data Size:    901567 Bytes = 880.4 kB
+   Load Address: 80060000
+   Entry Point:  80060000
+   Verifying Checksum ... crc32_fw: bf060040 - bf13c1fe (len:000dc1bf) calc...
+crc32_fw: range1 bf060040 - bf13c1fe
+OK
+   Uncompressing Kernel Image ... OK
+No initrd
+## Transferring control to Linux (at address 80060000) ...
+## Giving linux memsize in bytes, 67108864
+Starting kernel ...
+[    0.000000] Linux version 3.3.6 (zgembo@buildhost) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Thu May 24 15:25:10 JST 2012
+[    0.000000] bootconsole [early0] enabled
+[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
+[    0.000000] SoC: Atheros AR7242 rev 1
+[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
+[    0.000000] Determined physical RAM map:
+[    0.000000]  memory: 04000000 @ 00000000 (usable)
+[    0.000000] Initrd not found or empty - disabling initrd
+[    0.000000] Zone PFN ranges:
+[    0.000000]   Normal   0x00000000 -> 0x00004000
+[    0.000000] Movable zone start PFN for each node
+[    0.000000] Early memory PFN ranges
+[    0.000000]     0: 0x00000000 -> 0x00004000
+[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
+[    0.000000] Kernel command line:  board=WZR-HP-G300NH2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
+[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
+[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
+[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
+[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
+[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
+[    0.000000] Writing ErrCtl register=00000000
+[    0.000000] Readback ErrCtl register=00000000
+[    0.000000] Memory: 61800k/65536k available (2072k kernel code, 3736k reserved, 389k data, 200k init, 0k highmem)
+[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
+[    0.000000] NR_IRQS:48
+[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
+[    0.080000] pid_max: default: 32768 minimum: 301
+[    0.080000] Mount-cache hash table entries: 512
+[    0.090000] NET: Registered protocol family 16
+[    0.090000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
+[    0.100000] MIPS: machine is Buffalo WZR-HP-G300NH2
+[    0.330000] registering PCI controller with io_map_base unset
+[    0.340000] bio: create slab <bio-0> at 0
+[    0.350000] PCI host bridge to bus 0000:00
+[    0.350000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff]
+[    0.360000] pci_bus 0000:00: root bus resource [io  0x0000]
+[    0.360000] pci 0000:00:00.0: fixup device configuration
+[    0.370000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
+[    0.370000] pci 0000:00:00.0: using irq 40 for pin 1
+[    0.380000] Switching to clocksource MIPS
+[    0.380000] NET: Registered protocol family 2
+[    0.390000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
+[    0.390000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
+[    0.400000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
+[    0.400000] TCP: Hash tables configured (established 2048 bind 2048)
+[    0.410000] TCP reno registered
+[    0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes)
+[    0.420000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
+[    0.430000] NET: Registered protocol family 1
+[    0.450000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
+[    0.450000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
+[    0.470000] msgmni has been set to 120
+[    0.470000] io scheduler noop registered
+[    0.470000] io scheduler deadline registered (default)
+[    0.480000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
+[    0.510000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
+[    0.510000] console [ttyS0] enabled, bootconsole disabled
+[    0.510000] console [ttyS0] enabled, bootconsole disabled
+[    0.530000] m25p80 spi0.0: found mx25l12805d, expected m25p80
+[    0.530000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
+[    0.540000] m25p80 spi0.1: found mx25l12805d, expected m25p80
+[    0.550000] m25p80 spi0.1: mx25l12805d (16384 Kbytes)
+[    0.550000] Concatenating MTD devices:
+[    0.560000] (0): "spi0.0"
+[    0.560000] (1): "spi0.1"
+[    0.560000] into device "flash"
+[    0.570000] Creating 7 MTD partitions on "flash":
+[    0.580000] 0x000000000000-0x000000040000 : "u-boot"
+[    0.580000] 0x000000040000-0x000000050000 : "u-boot-env"
+[    0.590000] 0x000000050000-0x000000060000 : "art"
+[    0.600000] 0x000000060000-0x000000160000 : "kernel"
+[    0.600000] 0x000000160000-0x000001ff0000 : "rootfs"
+[    0.610000] mtd: partition "rootfs" set to be root filesystem
+[    0.620000] split_squashfs: no squashfs found in "flash"
+[    0.620000] 0x000001ff0000-0x000002000000 : "user_property"
+[    0.630000] 0x000000060000-0x000001ff0000 : "firmware"
+[    0.640000] ag71xx_mdio: probed
+[    0.650000] eth0: Atheros AG71xx at 0xb9000000, irq 4
+[    1.230000] eth0: AR8316 switch driver attached.
+[    1.230000] ar8316: Using port 4 as switch port
+[    1.330000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
+[    1.350000] TCP westwood registered
+[    1.350000] NET: Registered protocol family 17
+[    1.350000] 8021q: 802.1Q VLAN Support v1.8
+[    3.290000] JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
+[    3.310000] VFS: Mounted root (jffs2 filesystem) readonly on device 31:6.
+[    3.320000] Freeing unused kernel memory: 200k freed
+- preinit -
+Press the [f] key and hit [enter] to enter failsafe mode
+[    7.330000] eth0: link up (1000Mbps/Full duplex)
+- regular preinit -
+- init -
+[    9.540000] eth0: link down
+Please press Enter to activate this console. [   10.110000] usbcore: registered new interface driver usbfs
+[   10.120000] usbcore: registered new interface driver hub
+[   10.130000] usbcore: registered new device driver usb
+[   10.180000] loop: module loaded
+[   10.250000] PPP generic driver version 2.4.2
+[   10.340000] ip_tables: (C) 2000-2006 Netfilter Core Team
+[   10.480000] NET: Registered protocol family 24
+[   10.580000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
+[   10.580000] ehci-platform ehci-platform: Generic Platform EHCI Controller
+[   10.590000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
+[   10.630000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
+[   10.650000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
+[   10.650000] hub 1-0:1.0: USB hub found
+[   10.660000] hub 1-0:1.0: 1 port detected
+[   10.730000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
+[   13.600000] device eth0.1 entered promiscuous mode
+[   13.600000] device eth0 entered promiscuous mode
+[   14.340000] eth0: link up (1000Mbps/Full duplex)
+[   14.360000] br-lan: port 1(eth0.1) entered forwarding state
+[   14.370000] br-lan: port 1(eth0.1) entered forwarding state
+[   14.410000] br-lan: port 1(eth0.1) entered disabled state
+[   14.410000] device eth0.1 left promiscuous mode
+[   14.420000] device eth0 left promiscuous mode
+[   14.420000] br-lan: port 1(eth0.1) entered disabled state
+[   14.510000] device eth0.1 entered promiscuous mode
+[   14.510000] device eth0 entered promiscuous mode
+[   14.540000] br-lan: port 1(eth0.1) entered forwarding state
+[   14.550000] br-lan: port 1(eth0.1) entered forwarding state
+[   16.550000] br-lan: port 1(eth0.1) entered forwarding state
+BusyBox v1.19.4 (2012-05-23 21:35:24 JST) built-in shell (ash)
+Enter 'help' for a list of built-in commands.
+  _______                     ________        __
+ |       |.-----.-----.-----.|  |  |  |.----.|  |_
+ |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
+ |_______||   __|_____|__|__||________||__|  |____|
+          |__| W I R E L E S S   F R E E D O M
+ -----------------------------------------------------
+ ATTITUDE ADJUSTMENT (Bleeding Edge, r31835)
+ -----------------------------------------------------
+  * 1/4 oz Vodka      Pour all ingredients into mixing
+  * 1/4 oz Gin        tin with ice, strain into glass.
+  * 1/4 oz Amaretto
+  * 1/4 oz Triple sec
+  * 1/4 oz Peach schnapps
+  * 1/4 oz Sour mix
+  * 1 splash Cranberry juice
+ -----------------------------------------------------
+root@OpenWrt:/#</nowiki>
+</WRAP>\\
+===== Revision B0A0 (marketed as N300 HIGHPOWER GIGABIT / WZR-300HP) =====
+This board, marked WZR-HP-G302HV2 Rev: A3, is nearly identical to the other revisions, and the same image appears to flash successfully.  A visual inspection shows a different DDR2 module (both Nanya, but it looks like the previous chip was EOL'd), various capacitors in different positions, and a coil on the back of the board is covered in epoxy now.
+==== Boot Log ====
+<WRAP bootlog>
+<nowiki>BUFFALO U-BOOT Ver 1.00
+  == CPU:400MHz, DDR:400MHz, AHB:200MHz ==
+PB93 (ar7241 - Virian) U-boot
+DRAM:  64 MB
+WAN port disabling: done
+Top of RAM usable for U-Boot at: 84000000
+Reserving 267k for U-Boot at: 83fbc000
+Reserving 192k for malloc() at: 83f8c000
+Reserving 44 Bytes for Board Info at: 83f8bfd4
+Reserving 36 Bytes for Global Data at: 83f8bfb0
+Reserving 128k for boot params() at: 83f6bfb0
+Stack Pointer at: 83f6bf98
+Now running in RAM - U-Boot at: 83fbc000
+flash bank #0 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256]
+flash bank #1 found 16 MB flash [MX25L128-45E, blk:0x10000, sectors:256]
+Flash: 32 MB
+In:    serial
+Out:   serial
+Err:   serial
+Memory Test
+uboot use  83F6BFB0 - 84000000
+Memory Test start(80000000) end(83F00000) size(03F00000)
+Pattern 00000000  Writing...  Reading...
+Memory Test OK
+### buf_ver=[1.00] U-Boot Ver.=[1.00]
+### build_date(env)=[May 21 2012 - 06:39:59] build_date(bin)=[May 21 2012 - 06:39:59]
+ag7240_enet_initialize...
+Reading MAC Address from ENV(0x83f8c2f8)
+No valid address in Flash. Using fixed address
+Virian MDC CFG Value ==> 4
+: cfg1 0x7 cfg2 0x7014
+eth0: 02:aa:bb:cc:dd:1a
+eth0 up
+Virian MDC CFG Value ==> 4
+: cfg1 0xf cfg2 0x7214
+eth1: 00:03:7f:09:0b:ad
+ATHRS26: resetting s26
+ATHRS26: s26 reset done
+eth1 up
+eth0  02:AA:BB:CC:DD:1A
+, eth1  00:03:7F:09:0B:AD
+dup 1 speed 1000
+tftp server(receive) go, waiting:4[sec]
+Load address: 0x81f00000
+$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+         $$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$
+tftp server done
+Bytes transferred = 2949156 (2d0024 hex)
+Airstation Public header
+Recv fw image [2949124] bytes, now writing...
+flash-addr 0xBF060000 - 0xBF33FFFF
+search sector 0xbf060000 - 0xbf33ffff
+BANK #1 (6 : 51)
+  PPPP.Poooooooooooooooooooooooooo
+  oooooooooooooooooooo............
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+BANK #2 (-1 : -1)
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+  ................................
+First 0x6 last 0x33 sector size 0x10000
+Erased 46 sectors
+Copy to Flash...
+ Copy 2949124 byte to Flash...
+write data: 81f00020 --> bf060000  (len:2d0004)
+done
+change bootargs
+console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@320k(ART),64k@8128k(properties) mem=64M product_rev=1 UART=1
+## Booting image at bf060000 ...
+   Image Name:   MIPS OpenWrt Linux-3.3.8
+   Created:      2012-11-18   4:37:08 UTC
+   Image Type:   MIPS Linux Kernel Image (lzma compressed)
+   Data Size:    955998 Bytes = 933.6 kB
+   Load Address: 80060000
+   Entry Point:  80060000
+   Verifying Checksum ... crc32_fw: bf060040 - bf14969d (len:000e965e) calc...
+crc32_fw: range1 bf060040 - bf14969d
+OK
+   Uncompressing Kernel Image ... OK
+Ethernet Disabled!
+No initrd
+## Transferring control to Linux (at address 80060000) ...
+## Giving linux memsize in bytes, 67108864
+Starting kernel ...
+[    0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Nov 18 04:31:55 UTC 2012
+[    0.000000] bootconsole [early0] enabled
+[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
+[    0.000000] SoC: Atheros AR7242 rev 1
+[    0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
+[    0.000000] Determined physical RAM map:
+[    0.000000]  memory: 04000000 @ 00000000 (usable)
+[    0.000000] Initrd not found or empty - disabling initrd
+[    0.000000] Zone PFN ranges:
+[    0.000000]   Normal   0x00000000 -> 0x00004000
+[    0.000000] Movable zone start PFN for each node
+[    0.000000] Early memory PFN ranges
+[    0.000000]     0: 0x00000000 -> 0x00004000
+[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
+[    0.000000] Kernel command line:  board=WZR-HP-G300NH2 console=ttyS0,115200 rootfstype=squashfs,jffs2 noinitrd
+[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
+[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
+[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
+[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
+[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
+[    0.000000] Writing ErrCtl register=00000000
+[    0.000000] Readback ErrCtl register=00000000
+[    0.000000] Memory: 61496k/65536k available (2209k kernel code, 4040k reserved, 412k data, 212k init, 0k highmem)
+[    0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
+[    0.000000] NR_IRQS:51
+[    0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
+[    0.080000] pid_max: default: 32768 minimum: 301
+[    0.080000] Mount-cache hash table entries: 512
+[    0.090000] NET: Registered protocol family 16
+[    0.090000] gpiochip_add: registered GPIOs 0 to 17 on device: ath79
+[    0.100000] MIPS: machine is Buffalo WZR-HP-G300NH2
+[    0.330000] registering PCI controller with io_map_base unset
+[    0.340000] bio: create slab <bio-0> at 0
+[    0.350000] PCI host bridge to bus 0000:00
+[    0.350000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
+[    0.360000] pci_bus 0000:00: root bus resource [io  0x0000]
+[    0.360000] pci 0000:00:00.0: fixup device configuration
+[    0.370000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
+[    0.370000] pci 0000:00:00.0: using irq 40 for pin 1
+[    0.380000] Switching to clocksource MIPS
+[    0.380000] NET: Registered protocol family 2
+[    0.390000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
+[    0.390000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
+[    0.400000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
+[    0.400000] TCP: Hash tables configured (established 2048 bind 2048)
+[    0.410000] TCP reno registered
+[    0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes)
+[    0.420000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
+[    0.430000] NET: Registered protocol family 1
+[    0.450000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
+[    0.450000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
+[    0.470000] msgmni has been set to 120
+[    0.470000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
+[    0.480000] io scheduler noop registered
+[    0.480000] io scheduler deadline registered (default)
+[    0.490000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
+[    0.520000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
+[    0.530000] console [ttyS0] enabled, bootconsole disabled
+[    0.530000] console [ttyS0] enabled, bootconsole disabled
+[    0.540000] m25p80 spi0.0: found mx25l12805d, expected m25p80
+[    0.550000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
+[    0.550000] m25p80 spi0.1: found mx25l12805d, expected m25p80
+[    0.560000] m25p80 spi0.1: mx25l12805d (16384 Kbytes)
+[    0.570000] Concatenating MTD devices:
+[    0.570000] (0): "spi0.0"
+[    0.570000] (1): "spi0.1"
+[    0.580000] into device "flash"
+[    0.590000] Creating 7 MTD partitions on "flash":
+[    0.590000] 0x000000000000-0x000000040000 : "u-boot"
+[    0.600000] 0x000000040000-0x000000050000 : "u-boot-env"
+[    0.600000] 0x000000050000-0x000000060000 : "art"
+[    0.610000] 0x000000060000-0x000000160000 : "kernel"
+[    0.620000] 0x000000160000-0x000001ff0000 : "rootfs"
+[    0.620000] mtd: partition "rootfs" set to be root filesystem
+[    0.630000] mtd: partition "rootfs_data" created automatically, ofs=330000, len=1CC0000
+[    0.640000] 0x000000330000-0x000001ff0000 : "rootfs_data"
+[    0.650000] 0x000001ff0000-0x000002000000 : "user_property"
+[    0.650000] 0x000000060000-0x000001ff0000 : "firmware"
+[    0.660000] ag71xx_mdio: probed
+[    0.670000] eth0: Atheros AG71xx at 0xb9000000, irq 4
+[    1.250000] eth0: Atheros AR8316 switch driver attached.
+[    1.250000] ar8316: Using port 4 as switch port
+[    1.350000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.0:00 [uid=004dd041, driver=Atheros AR8216/AR8236/AR8316]
+[    1.370000] TCP cubic registered
+[    1.370000] NET: Registered protocol family 17
+[    1.370000] Bridge firewalling registered
+[    1.380000] 8021q: 802.1Q VLAN Support v1.8
+[    1.390000] VFS: Mounted root (squashfs filesystem) readonly on device 31:6.
+[    1.400000] Freeing unused kernel memory: 212k freed
+- preinit -
+Press the [f] key and hit [enter] to enter failsafe mode
+[    5.350000] eth0: link up (1000Mbps/Full duplex)
+- regular preinit -
+jffs2 not ready yet; using ramdisk
+- init -
+[    7.130000] eth0: link down
+[    9.150000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
+[    9.150000] Backport based on wireless-testing.git master-2012-09-07
+[    9.160000] compat.git: wireless-testing.git
+[    9.190000] cfg80211: Calling CRDA to update world regulatory domain
+[    9.200000] cfg80211: World regulatory domain updated:
+[    9.200000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
+[    9.210000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[    9.220000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
+[    9.230000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
+[    9.240000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[    9.240000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[    9.650000] usbcore: registered new interface driver usbfs
+[    9.660000] usbcore: registered new interface driver hub
+[    9.670000] usbcore: registered new device driver usb
+[   10.400000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
+[   10.420000] ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xb0000000, irq=40
+[   10.430000] cfg80211: Calling CRDA for country: US
+[   10.440000] cfg80211: Regulatory domain changed to country: US
+[   10.440000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
+[   10.450000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
+[   10.460000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
+[   10.470000] cfg80211:   (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[   10.470000] cfg80211:   (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[   10.480000] cfg80211:   (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
+[   10.490000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
+[   10.540000] PPP generic driver version 2.4.2
+[   10.800000] ip_tables: (C) 2000-2006 Netfilter Core Team
+[   11.020000] NET: Registered protocol family 24
+[   11.040000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
+[   11.050000] ehci-platform ehci-platform: Generic Platform EHCI Controller
+[   11.050000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
+[   11.090000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
+[   11.110000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
+[   11.110000] hub 1-0:1.0: USB hub found
+[   11.120000] hub 1-0:1.0: 1 port detected
+[   11.140000] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
+[   11.370000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
+Please press Enter to activate this console. [   15.220000] device eth0.1 entered promiscuous mode
+[   15.220000] device eth0 entered promiscuous mode
+[   16.390000] eth0: link up (1000Mbps/Full duplex)
+[   16.400000] br-lan: port 1(eth0.1) entered forwarding state
+[   16.400000] br-lan: port 1(eth0.1) entered forwarding state
+[   18.400000] br-lan: port 1(eth0.1) entered forwarding state
+[   25.930000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
+[   25.930000] jffs2_build_filesystem(): unlocking the mtd device... done.
+[   25.940000] jffs2_build_filesystem(): erasing all blocks after the end marker...</nowiki>
+</WRAP>\\
+===== Tags =====
+[[meta:tags|How to add tags]]
+{{tag>GigabitEthernet 1NIC 1WNIC 5Port 32flash 64ram}}

OpenWrt Wiki

User Tools

Site Tools

Differences

Page Tools