User Tools

Site Tools


toh:buffalo:wzr-hp-g450h

Buffalo WZR-HP-G450H

TFTP Recovery

To perform a TFTP recovery on this model:

  • Set your IP address to 192.168.11.2
  • Set a static arp entry for 192.168.11.1 to 02:aa:bb:cc:dd:23
  • TFTP the image during the 4 second window and wait

Hardware

Info

Architecture: MIPS
Vendor: Qualcomm Atheros
Bootloader: U-Boot
System-On-Chip: AR7242
CPU/Speed
Flash-Chip:
Flash size: 32 MiB
RAM: 64 MiB
Wireless: Atheros AR9381?
Ethernet: AR8316 swconfig
USB: Yes 1x 2.0
Serial:
JTAG:

Photos

Serial Port and Internal Pictuers

serial_pins.jpg

Serial Pinout:

Top Row: gnd, rx, tx, vcc
Bottom Row: rx, tx, gnd, vcc

top.jpg
bottom.jpg

Installation

Migrate from DD-WRT to OpenWrt

  1. Enable SSH or Telnet on the router
  2. Login to the router via SSH or Telnet
  3. Change directory to /tmp and download OpenWrt firmware image file:
    cd /tmp
    wget http://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/openwrt-ar71xx-generic-wzr-hp-g450h-squashfs-sysupgrade.bin
  4. Overwrite current firmware with the downloaded one:
    mtd -r write openwrt-ar71xx-generic-wzr-hp-g450h-squashfs-sysupgrade.bin linux

After flashing, the router should go down for a reboot and return running OpenWrt.

How recover from a broken firmware


1. Start a TFTP server on your computer. On Fedora, you can do it with:
$ sudo yum install tftpd-server
$ sudo service xinetd start
$ cd /var/lib/tftpboot

On OS X, you can use TftpServer.

2. Download the sysupgrade image from OpenWRT trunk:
$ sudo wget http://downloads.openwrt.org/attitude_adjustment/12.09-rc1/ar71xx/generic/openwrt-ar71xx-generic-wzr-hp-g450h-jffs2-sysupgrade.bin

3. Set up minicom:
$ sudo minicom -s
- Set serial device to /dev/ttyUSDB0
- Turn OFF Hardware Flow Control
- Save the configuration as default and exit

4. Plugin in the FTDI USB cable that's wired to the router's pins above with router being turned off, start minicom and then turn the router on.

5. Keep pressing Control + C until you see a "ar7240>" prompt.

6. Find out at which IP address the TFTP server should be running and set up your LAN connection accordingly. By default, your computer should have a static IP address at 192.168.11.1. (use `printenv` command and "ipaddr" and "serverip" properties)

7. Copy the sysupgrade image to RAM. Write down the number of transferred bytes in hex:
ar7240> tftpboot 81F00000 openwrt-ar71xx-generic-wzr-hp-g450h-jffs2-sysupgrade.bin

8. Erase existing firmware (or whatever was there; u-boot won't be erased with this, you're safe; it will take a while. e)
ar7240> erase BF060000 BEFFFFFF

9. Copy the image you uploaded in step 6 to flash memory
ar7240> cp.b 81f00000 BF060000 <number of bytes copied in step 6, hex>

10. Boot into your, now fully-functional, router! (first boot will take some time)
ar7240> bootm

11. Now flash the same image you downloaded in step 2 but through Open-WRTs administration interface (System > Software > Flash Firmware) and reboot your router.

Firmware

u-boot default environment

bootargs=console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@320k(ART),64k@8128k(properties),8192k@8192k(flash1),16384k@16384k(flash2)
bootcmd=bootm BF060000
baudrate=115200
ethaddr=02:AA:BB:CC:DD:23
ipaddr=192.168.11.1
serverip=192.168.11.2
tmp_ram=81F00000
tmp_bottom=83F00000
fw_eaddr=BF060000 BEFFFFFF
uboot_eaddr=BF000000 BF03FFFF
u_fw=erase $fw_eaddr; cp.fw $fileaddr BF060000 $filesize; bootm BF060000;
ut_fw=tftp $tmp_ram firmware.bin; erase $fw_eaddr; cp.fw $fileaddr BF060000 $filesize; bootm BF060000;
ut_uboot=tftp $tmp_ram u-boot.bin; protect off $uboot_eaddr; erase $uboot_eaddr; cp.b $fileaddr BF000000 $filesize;
melco_id=RD_BB10082
hw_rev=0
tftp_wait=4
uboot_ethaddr=02:AA:BB:CC:DD:23
DEF-p_wireless_ath0_11bg-authmode=psk
DEF-p_wireless_ath0_11bg-crypto=tkip+aes
DEF-p_wireless_ath0_11bg-authmode_ex=mixed-psk
DEF-p_wireless_ath0_11bg-wpapsk=scmyermf38a8b
pincode=18797312
custom_id=0
buf_ver=1.00
product=WZR-HP-G450H
build_date=Apr  6 2011 - 08:52:48
buf_crc=D8FD7242
region=US
accept_open_rt_fmt=1
stdin=serial
stdout=serial
stderr=serial
loadaddr=81F00000
ethact=eth0

Boot Sequence

This complete boot sequence shows Buffalo's U-BOOT ver 1.00, its TftpServer timing, and factory default DD-WRT kernel messages while booting up

BUFFALO U-BOOT Ver 1.00
  == CPU:400MHz, DDR:400MHz, AHB:200MHz ==
AP111 (ar7241 - Virian) U-boot
DRAM:  64 MB
WAN port disabling: done
Top of RAM usable for U-Boot at: 84000000
Reserving 258k for U-Boot at: 83fbc000
Reserving 192k for malloc() at: 83f8c000
Reserving 44 Bytes for Board Info at: 83f8bfd4
Reserving 36 Bytes for Global Data at: 83f8bfb0
Reserving 128k for boot params() at: 83f6bfb0
Stack Pointer at: 83f6bf98
Now running in RAM - U-Boot at: 83fbc000
flash bank #0 found 16 MB flash [W25Q128BV, blk:0x10000, sectors:256]
flash bank #1 found 16 MB flash [W25Q128BV, blk:0x10000, sectors:256]
Flash: 32 MB
In:    serial
Out:   serial
Err:   serial
Memory Test (address line)
uboot use  83F6BFB0 - 84000000
Memory Test start(0x80000000) end(0x83F00000) size(67108864)
Data line test start:0x80000000 pattern 0x00000001 0x00000003 0x00000007 0x0000000F 0x00000005 0x00000015 0x00000055 0xAAAAAAAA 
Address line test start:0x80000000 len:0x3f00000 pattern 0xAAAAAAAA 0x55555555  
Fill test patnum:5 
fill Pattern 5555AAAA  Writing...   Reading...
fill Pattern AAAA5555  Writing...   Reading...
fill Pattern 0000FFFF  Writing...   Reading...
fill Pattern FFFF0000  Writing...   Reading...
fill Pattern AAAAAAAA  Writing...   Reading...
Memory Test OK
### buf_ver=[1.00] U-Boot Ver.=[1.00]
### build_date(env)=[Apr  6 2011 - 08:52:48] build_date(bin)=[Apr  6 2011 - 08:52:48]
ag7240_enet_initialize...
Reading MAC Address from ENV(0x83f8c322)
No valid address in Flash. Using fixed address
Virian MDC CFG Value ==> 4
: cfg1 0x7 cfg2 0x7114
eth0: 02:aa:bb:cc:dd:23
athrs16_reg_init: complete
eth0 up
Virian MDC CFG Value ==> 4
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
eth1 up
eth0  02:AA:BB:CC:DD:23
, eth1  00:03:7F:09:0B:AD

eth0 link down

tftp server(receive) go, waiting:4[sec]
eth0 link down
Load address: 0x81f00000

TftpServer Timeout;
no file was loaded.
LAN port disabling: done

## Checking Image at bf060000 ...
   Image Name:   MIPS Linux Kernel Image
   Created:      2011-05-27  10:22:38 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1016696 Bytes = 992.9 kB
   Load Address: 80002000
   Entry Point:  80006150
   Verifying Checksum ... crc32_fw: bf060040 - bf1583b7 (len:000f8378) calc...
crc32_fw: range1 bf060040 - bf1583b7
OK
change bootargs
console=ttyS0,115200 root=31:03 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),1152k@384k(uImage),6592k@1536k(rootfs),64k@320k(ART),64k@8128k(properties),8192k@8192k(flash1),16384k@16384k(flash2) mem=64M
## Booting image at bf060000 ...
   Image Name:   MIPS Linux Kernel Image
   Created:      2011-05-27  10:22:38 UTC
   Image Type:   MIPS Linux Kernel Image (lzma compressed)
   Data Size:    1016696 Bytes = 992.9 kB
   Load Address: 80002000
   Entry Point:  80006150
   Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80006150) ...
## Giving linux memsize in bytes, 67108864

Starting kernel ...

[    0.000000] Linux version 2.6.34.9-svn17089 (root@dd-wrt) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #5719 Fri May 27 12:10:20 CEST 2011
[    0.000000] flash_size passed from bootloader = 32
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU revision is: 00019374 (MIPS 24Kc)
Booting AR7240(Python)...
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Zone PFN ranges:
[    0.000000]   Normal   0x00000000 -> 0x00004000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0: 0x00000000 -> 0x00004000
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyS0,115200 root=1f02 rootfstype=squashfs noinitrd init=/sbin/init
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] Writing ErrCtl register=00000000
[    0.000000] Readback ErrCtl register=00000000
[    0.000000] Memory: 61804k/65536k available (2171k kernel code, 3732k reserved, 541k data, 148k init, 0k highmem)
[    0.000000] NR_IRQS:128
[    0.000000] Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
[    0.240000] Mount-cache hash table entries: 512
[    0.240000] NET: Registered protocol family 16
[    0.250000] found calibration data for slot 0 on 0xBF050000
[    0.460000] registering PCI controller with io_map_base unset
[    0.470000] bio: create slab <bio-0> at 0
[    0.480000] usbcore: registered new interface driver usbfs
[    0.480000] usbcore: registered new interface driver hub
[    0.490000] usbcore: registered new device driver usb
[    0.490000] detected swapped eeprom data
[    0.490000] pci 0000:00:00.0: fixup device configuration
[    0.500000] bootstrap returns device 168C:30
[    0.500000] move calibration data offset 12288
[    0.510000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1001ffff 64bit]
[    0.510000] pci 0000:00:00.0: BAR 0: set to [mem 0x10000000-0x1001ffff 64bit] (PCI address [0x10000000-0x1001ffff]
[    0.520000] pci 0000:00:00.0: BAR 6: assigned [mem 0x10020000-0x1002ffff pref]
[    0.520000] PCI: mapping irq 48 to pin1@0000:00:00.0
[    0.530000] fixup irq: got 48
[    0.530000] Switching to clocksource MIPS
[    0.540000] NET: Registered protocol family 2
[    0.540000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.540000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[    0.550000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[    0.550000] TCP: Hash tables configured (established 2048 bind 2048)
[    0.560000] TCP reno registered
[    0.560000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.570000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.570000] NET: Registered protocol family 1
[    0.580000] gpio_proc: module loaded and /proc/gpio/ created
[    0.590000] wl0gpio_proc: module loaded and /proc/wl0gpio/ created
[    0.590000] init_vdso successfull
[    0.600000] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[    0.600000] msgmni has been set to 120
[    0.610000] io scheduler noop registered
[    0.610000] io scheduler deadline registered (default)
[    0.620000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[    0.630000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 19) is a 16550A
[    0.630000] console [ttyS0] enabled, bootconsole disabled
[    0.630000] console [ttyS0] enabled, bootconsole disabled
[    0.640000] check spi banks 2
[    0.650000] 0000 : EF 40 18
[    0.650000] found W25Q128BV device on bank#0
[    0.650000] 0000 : EF 40 18
[    0.660000] found W25Q128BV device on bank#1
[    0.660000] SPI flash size total:32 Mbytes
[    0.730000] 
[    0.730000] found squashfs at 159000
[    0.740000] Creating 9 MTD partitions on "ar7240-nor0":
[    0.740000] 0x000000000000-0x000000050000 : "RedBoot"
[    0.750000] 0x000000060000-0x000001fe0000 : "linux"
[    0.760000] 0x000000159000-0x000000df0000 : "rootfs"
[    0.760000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[    0.780000] mtd: partition "rootfs" set to be root filesystem
[    0.780000] 0x000000df0000-0x000001fe0000 : "ddwrt"
[    0.790000] 0x000001fe0000-0x000001ff0000 : "nvram"
[    0.790000] 0x000001ff0000-0x000002000000 : "FIS directory"
[    0.800000] 0x000001ff0000-0x000002000000 : "board_config"
[    0.810000] 0x000000000000-0x000002000000 : "fullflash"
[    0.810000] 0x000000040000-0x000000050000 : "uboot-env"
[    0.820000] PPP generic driver version 2.4.2
[    0.820000] PPP Deflate Compression module registered
[    0.830000] PPP BSD Compression module registered
[    0.830000] PPP MPPE Compression module registered
[    0.840000] NET: Registered protocol family 24
[    0.840000] PPPoL2TP kernel driver, V1.0
[    0.850000] IMQ driver loaded successfully.
[    0.850000] 	Hooking IMQ before NAT on PREROUTING.
[    0.860000] 	Hooking IMQ after NAT on POSTROUTING.
[    0.860000] tun: Universal TUN/TAP device driver, 1.6
[    0.870000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.870000] AG7240: Length per segment 1544
[    0.880000] AG7240: Max segments per packet 1
[    0.880000] AG7240: Max tx descriptor count    128
[    0.890000] AG7240: Max rx descriptor count    252
[    0.890000] AG7240: fifo cfg 3 01f00140
[    0.900000] AG7240CHH: Mac address for unit 0
[    0.900000] AG7240CHH: ff:ff:ff:ff:ff:ff 
[    1.110000] AG7240CHH: Mac address for unit 1
[    1.110000] AG7240CHH: ff:ff:ff:ff:ff:ff 
[    1.320000] Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
[    1.320000] u32 classifier
[    1.330000]     input device check on 
[    1.330000]     Actions configured 
[    1.330000] Netfilter messages via NETLINK v0.30.
[    1.340000] nf_conntrack version 0.5.0 (965 buckets, 3860 max)
[    1.350000] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[    1.350000] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[    1.360000] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    1.370000] nf_conntrack_rtsp v0.6.21 loading
[    1.370000] nf_nat_rtsp v0.6.21 loading
[    1.380000] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.380000] IPP2P v0.8.2 loading
[    1.380000] TCP westwood registered
[    1.390000] TCP hybla registered
[    1.390000] TCP vegas registered
[    1.390000] NET: Registered protocol family 17
[    1.400000] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    1.410000] All bugs added by David S. Miller <davem@redhat.com>
[    1.490000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[    1.500000] Freeing unused kernel memory: 148k freed
start service
starting Architecture code for wzrg450
starting hotplug
Jan  1 00:00:03 udevtrigger[195]: parse_config_file: can't open '/etc/udev/udev.conf' as config file: No such file or directory
done
load ATH Ethernet Driver
insmod: ag7100_mod.ko: module not found
configure eth0 to 10:6F:3F:25:FD:8D
[    4.280000] ag7240_ring_alloc Allocated 2048 at 0x838c5800
[    4.280000] ag7240_ring_alloc Allocated 4032 at 0x83a01000
[    4.290000] Virian MDC CFG Value ==> 4
[    4.290000] CFG Board AP96 
[    4.300000] athrs16_reg_init complete.
[    4.300000] Setting PHY...
configure vlan1 to 10:6F:3F:25:FD:8D
configure vlan2 to 10:6F:3F:25:FD:8D
ifconfig: SIOCSIFHWADDR: Device or resource busy
load ATH 802.11 a/b/g Driver
insmod: ath_hal.ko: module not found
insmod: ath_pci.ko: module not found
insmod: ath_ahb.ko: module not found
load ATH9K 802.11n Driver
[    5.550000] Compat-wireless backport release: compat-wireless-2011-05-11-r26927
[    5.560000] Backport based on wireless-testing.git master-2011-05-13
insmod: compat_firmware_class.ko: module not found
[    5.850000] cfg80211: Calling CRDA to update world regulatory domain
[    5.980000] cfg80211: World regulatory domain updated:
[    5.990000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    6.000000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    6.000000] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    6.010000] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    6.020000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    6.030000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    6.970000] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xb0000000, irq=48
[    6.980000] cfg80211: Calling CRDA for country: US
[    7.010000] cfg80211: Regulatory domain changed to country: US
[    7.020000] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    7.030000] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[    7.030000] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[    7.040000] cfg80211:     (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.050000] cfg80211:     (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.060000] cfg80211:     (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.070000] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
/bin/sh: can't create /proc/sys/dev/wifi0/ledpin: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/softled: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi1/ledpin: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi1/softled: nonexistent directory
[USB] checking...
umount: can't umount /mnt: Invalid argument
rmmod: usblp: No such file or directory
rmmod: printer: No such file or directory
rmmod: usb-storage: No such file or directory
rmmod: sd_mod: No such file or directory
rmmod: scsi_wait_scan: No such file or directory
rmmod: scsi_mod: No such file or directory
rmmod: usb-ohci: No such file or directory
rmmod: ohci-hcd: No such file or directory
rmmod: uhci-hcd: No such file or directory
rmmod: usb-uhci: No such file or directory
rmmod: ehci-hcd: No such file or directory
rmmod: usbcore: No such file or directory
rmmod: xfs: No such file or directory
rmmod: msdos: No such file or directory
rmmod: vfat: No such file or directory
rmmod: fat: No such file or directory
rmmod: nls_utf8: No such file or directory
rmmod: nls_iso8859-2: No such file or directory
rmmod: nls_iso8859-1: No such file or directory
rmmod: nls_cp437: No such file or directory
rmmod: nls_base: No such file or directory
rmmod: ext3: No such file or directory
rmmod: jbd: No such file or directory
rmmod: ext2: No such file or directory
rmmod: mbcache: No such file or directory
rmmod: fuse: No such file or directory
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
ath9k deconfigure_single: phy0 ath0
[    9.670000] device br0 entered promiscuous mode
killall: ead: no process killed
[    9.750000] device vlan1 entered promiscuous mode
[    9.760000] device eth0 entered promiscuous mode
/bin/sh: ead: not found[    9.770000] br0: port 1(vlan1) entering learning state

[    9.780000] device br0 left promiscuous mode
[    9.780000] device br0 entered promiscuous mode
[    9.790000] device br0 left promiscuous mode
[    9.800000] device br0 entered promiscuous mode
ifconfig: ioctl 0x8914 failed: Cannot assign requested address
ath9k deconfigure_single: phy0 ath0
/bin/sh: can't create /proc/sys/dev/wifi0/superchannel: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/regdomain: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/countrycode: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/outdoor: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/antennagain: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/antennagainsub: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/channelbw: nonexistent directory
/bin/sh: can't create /proc/sys/dev/wifi0/channelshift: nonexistent directory
ath9k configure_single: phy0 ath0
/bin/sh: can't create /sys/kernel/debug/ath9k/phy0/rx_chainmask: nonexistent directory
/bin/sh: can't create /sys/kernel/debug/ath9k/phy0/tx_chainmask: nonexistent directory
command failed: Invalid argument (-22)
call mac80211autochannel for interface: ath0
mac80211autochannel interface: ath0 frequency: 2412
setup ath0 10:6F:3F:25:FD:8D
Configuration file: /tmp/ath0_hostap.conf
[   10.590000] device ath0 entered promiscuous mode
[   10.610000] br0: port 2(ath0) entering learning state
Using interface ath0 with hwaddr 10:6f:3f:25:fd:8d and ssid '106F3F25FD8D'
[   10.780000] br0: port 1(vlan1) entering forwarding state
device ath0 is already a member of a bridge; can't enslave it to bridge br0.
killall: roaming_daemon: no process killed
rmmod: bonding: No such file or directory
[   11.160000] bonding: Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
[   11.170000] bonding: MII link monitoring set to 100 ms
[   11.610000] br0: port 2(ath0) entering forwarding state
cp: cannot stat '/tmp/mycron.d/*': No such file or directory
cp: cannot stat '/jffs/mycron.d/*': No such file or directory
cp: cannot stat '/mmc/mycron.d/*': No such file or directory
rmmod: n_hdlc: No such file or directory
[   12.230000] device vlan2 entered promiscuous mode
[   12.250000] device vlan2 left promiscuous mode
SIOCGIFFLAGS: No such device
ath9k radio on: phy-1 ath-1
/bin/sh: can't create /proc/sys/dev/wifi0/silent: nonexistent directory
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
[   13.830000] etherip: Ethernet over IPv4 tunneling driver
rmmod: ipt_webstr: No such file or directory
rmmod: ipt_layer7: No such file or directory
rmmod: ipt_ipp2p: No such file or directory
The Milkfish Router Services
ERROR: Necessary service setting not found: milkfish_username - aborting.
rmmod: ebt_dnat: No such file or directory
rmmod: ebt_snat: No such file or directory
killall: proxywatchdog.sh: no process killed
The Milkfish Router Services
Restoring SIP ddsubscriber database from NVRAM...
rmmod: ebt_mark_m: No such file or directory
rmmod: ebt_mark: No such file or directory
rmmod: ebtable_filter: No such file or directory
Empty.
The Milkfish Router Services
Restoring SIP ddaliases database from NVRAM...
rmmod: ebtable_nat: No such file or directory
Empty.
rmmod: ebtables: No such file or directory
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-arptables: nonexistent directory
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-ip6tables: nonexistent directory
/bin/sh: can't create /proc/sys/net/bridge/bridge-nf-call-iptables: nonexistent directory
rmmod: imq: No such file or directory
umount: can't umount /tmp/smbshare: No such file or directory
rmmod: cifs: No such file or directory
killall: schedulerb.sh: no process killed
killall: shatd: no process killed
killall: wdswatchdog.sh: no process killed

DD-WRT v24-sp2 std (c) 2011 NewMedia-NET GmbH
Release: 05/27/11 (SVN revision: 17140)
DD-WRT login: 

Tags

For some Help with the Tags, please have a look here: tags

toh/buffalo/wzr-hp-g450h.txt · Last modified: 2013/05/21 21:24 (external edit)