1. ? (square)
2. ?
3. ?
4. Rx
5. Tx
6. GND

Connection settings: 38400 8N1, software flow control

Found 1 x 2M flash memory —RealTek(RTL865x)at 2008.07.29-17:38+0800 version v1.3.A [32bit](289MHz) no sys signature at 10000! no sys signature at 20000! Jump to image start=0x80300000… decompressing kernel: Uncompressing Linux… done, booting the kernel. done decompressing kernel. early printk enabled Determined physical RAM map: memory: 01000000 @ 00000000 (usable) On node 0 totalpages: 4096 zone(0): 4096 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock1 console=0 single Calibrating delay loop… 284.26 BogoMIPS Memory: 8452k/16384k available (2037k kernel code, 7932k reserved, 272k data, 6) Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes) Inode-cache hash table entries: 1024 (order: 1, 8192 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 4096 (order: 2, 16384 bytes) check_wait… unavailable. POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Serial driver version 6.02 (2003-03-12) with no serial options enabled ttyS00 at 0x2000 (irq = 5) is a rtl_uart1 state→flags=00000000 Realtek GPIO Driver for Flash Reload Default block: 64 slots per queue, batch=16 PPP generic driver version 2.4.1 PPP MPPE Compression module registered RealTek E-Flash System Driver. (C) 2002 RealTek Corp. Found 1 x 2M Byte AMD AM29LV160DB at 0xbe000000 Creating 2 MTD partitions on "DiskOnChip Millennium": 0x00000000-0x000e0000 : "boot+cfg+linux" 0x000e0000-0x00200000 : "root fs" Realtek 865x Ethernet driver v0.6 (Mar 26, 2008) Probe external PHY status, WAN port is set to port 0. Initialize Hardware Tables Driver …… chip name: 865xC, chip revid: 1 eth0: RTL865x-NIC at 0xbb804000, 00:00:00:00:00:11, IRQ 2 eth1: RTL865x-NIC at 0xbb804000, 00:00:00:00:00:22, IRQ 2 Realtek FastPath v1.06 RTL8190 driver version 1.10 (2008-07-09) pci_request_regions: PCI regions already reserved correcting to 16 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 1024 bind 2048) Linux IP multicast router 0.06 plus PIM-SM ip_conntrack version 2.1 (512 buckets, 4096 max) - 324 bytes per conntrack PPTP netfilter connection tracking: registered PPTP netfilter NAT helper: registered ip_tables: (C) 2000-2002 Netfilter core team NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: Ethernet Bridge 008 for NET4.0 VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 64k freed mount /proc file system ok! mount /var file system ok! serial console detected. Disabling virtual terminals. init started: BusyBox v1.00-pre8 (2005.09.16-02:17+0000) multi-call binary BusyBox v1.00-pre8 (2005.09.16-02:17+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. killall: pptp.sh: no process killed killall: pppoe.sh: no process killed Initialize wlan0 interface Initialize wlan0-va0 interface Initialize wlan0-va1 interface Initialize wlan0-va2 interface Initialize wlan0-va3 interface Setup BRIDGE interface killall: syslogd: no process killed killall: klogd: no process killed SIOCGIFFLAGS: No such device bridge br0 doesn't exist; can't delete it Setup bridge… device eth0 entered promiscuous mode SIOCDELRT: No such process device wlan0 entered promiscuous mode TPT: unreasonable target TSSI 0 SIOCDELRT: No such process br0: port 2(wlan0) entering listening state br0: port 1(eth0) entering listening state br0: port 2(wlan0) entering learning state br0: port 2(wlan0) entering forwarding state br0: topology change detected, propagating br0: port 1(eth0) entering learning state br0: port 1(eth0) entering forwarding state br0: topology change detected, propagating SIOCDELRT: No such process SIOCDELRT: No such process SIOCDELRT: No such process SIOCDELRT: No such process WiFi Simple Config v1.7 (2008.07.11-08:36+0000). IEEE 802.11f (IAPP) using interface br0 (v1.7) Setup WAN interface Auto-Discovery (ver 1.01) # cat /proc/cpuinfo system type : Philips Nino processor : 0 cpu model : R3000 V0.0 BogoMIPS : 279.34 wait instruction : yes microsecond timers : no tlb_entries : 32 extra interrupt vector : no hardware watchpoint : no VCED exceptions : not available VCEI exceptions : not available ll emulations : 0 sc emulations : 0 # cat /proc/kmsg <4>Linux version 2.4.18-MIPS-01.00 (root@localhost.localdomain) (gcc version 3.2.3-1.2.8) #9 Fri Aug 8 16:58 <4>early printk enabled <4>Determined physical RAM map: <4> memory: 01000000 @ 00000000 (usable) <4>On node 0 totalpages: 4096 <4>zone(0): 4096 pages. <4>zone(1): 0 pages. <4>zone(2): 0 pages. <4>Kernel command line: root=/dev/mtdblock1 console=0 single […] # cat /proc/meminfo total: used: free: shared: buffers: cached: Mem: 8720384 8114176 606208 0 663552 2936832 Swap: 0 0 0 # cat /proc/mtd dev: size erasesize name mtd0: 000e0000 00010000 "boot+cfg+linux" mtd1: 00120000 00010000 "root fs"

Power on while holding Reset button:

—Escape booting by user <RealTek>help —————– COMMAND MODE HELP —————— HELP (?) : Print this help message D <Address> <Len> DB <Address> <Len> EW <Address> <Value1> <Value2>… EH <Address> <Value1> <Value2>… EB <Address> <Value1> <Value2>… EC <Address> <Value1> <Length>… CMP: CMP <dst><src><length> IPCONFIG:<TargetAddress> J: Jump to <TargetAddress> FLW: FLW <dst><src><length> FLR: FLR <dst><src><length> LOADADDR: <Load Address> AUTOBURN: 0/1