toh:compex:wp543ahv
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Previous revision | ||
|
toh:compex:wp543ahv [2013/01/31 09:35] |
toh:compex:wp543ahv [2016/02/25 10:52] (current) dangh [Hardware info] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== Compex WP543AHV ====== | ||
| + | The device is supported in OpenWrt since Kamikaze 8.09. | ||
| + | |||
| + | ===== Hardware info ===== | ||
| + | ^ Architecture | MIPS | | ||
| + | ^ Vendor | Atheros | | ||
| + | ^ Bootloader | CFE | | ||
| + | ^ System-On-Chip | AR7161 | | ||
| + | ^ CPU Speed | 680 Mhz | | ||
| + | ^ Flash size | 8 MB (up to 16 MB)| | ||
| + | ^ RAM | 32 MB (Max 64 MB) DDR SDRAM | | ||
| + | ^ Wireless | 2 × MiniPCI slots, support all Compex MiniPCI cards | | ||
| + | ^ Ethernet | 1 × 10/100 Base-TX Ethernet Port (with Auto MDI/MDIX) | | ||
| + | ^ USB | 2 × USB 2.0 ports (optional) | | ||
| + | ^ Serial | yes | | ||
| + | ^ JTAG | yes | | ||
| + | |||
| + | ===== Installation ===== | ||
| + | |||
| + | ==== Restore mode ==== | ||
| + | |||
| + | If you want to upload firmware to router by tftp, you will have to turn your device to this mode. The procedure is following: | ||
| + | |||
| + | - Turn off the device. | ||
| + | - Press and hold the reset button. | ||
| + | - Plug the device (still hold the button). | ||
| + | - Wait until the Diagnostic LED (second from the left) starts flashing quickly. (This will happen almost immediately.) | ||
| + | - Now release the reset button. Your router is in Restore mode. | ||
| + | |||
| + | ==== TFTP installation notes ==== | ||
| + | |||
| + | Set your ethernet interface into static mode (IP address 192.168.168.10, netmask 255.255.255.0, default gateway 192.168.168.1), put your router into **[[toh:compex:wp543ahv#restore_mode|Restore mode]]** and upload the firmware by TFTP using the following commands (replace XXXXXX with wp543): | ||
| + | |||
| + | <code> | ||
| + | $ tftp 192.168.168.1 | ||
| + | tftp> binary | ||
| + | tftp> trace | ||
| + | tftp> put openwrt-ar71xx-wp543.bin | ||
| + | </code> | ||
| + | |||
| + | Diagnostic LED will now stop blinking for a while; if the flashing procedure is successfully done, it will start blinking slowly. Now reboot your router manually (turn off - turn on) and OpenWrt will boot. | ||
| + | |||
| + | ===== Upgrading OpenWRT (on compex Myloader) ===== | ||
| + | |||
| + | === Minimum Requirement === | ||
| + | - Compex loader version 2.54 or above. | ||
| + | - OpenWRT will only be supported on WP543 with 4MB NOR flash and above. | ||
| + | - Please ensure that the Ethernet connection is able to ping address = 192.168.168.1 | ||
| + | - If there is a USB NAND flash available on board, you would need to change the loader configuration. Please refer to “what to do if there is a onboard NAND Flash”. | ||
| + | |||
| + | === Compiling OpenWRT suitable for use on WP543 === | ||
| + | |||
| + | - Getting source codes <code bash> | ||
| + | $ svn co -r 12448 https://snv.openwrt.org/openwrt/trunk</code> | ||
| + | - Apply patches from the files mod-wp543.tgz (<del>[[http://www.cpx.cz/dls/WP543_routerboard/|resource url]]</del>)<code bash> | ||
| + | $ tar -zxvf mod-wp543.tgz | ||
| + | $ cp -a mod-wp543/* trunk/</code> | ||
| + | - Compile<code bash> | ||
| + | $ cd trunk | ||
| + | $ cp wp543.config .config | ||
| + | $ make</code> | ||
| + | |||
| + | OpenWRT Firmware will be in //bin/openwrt-ar71xx-wp543.bin// | ||
| + | |||
| + | === Uploading the OpenWRT firmware to WP543 running MyLoader v2.54.0717 === | ||
| + | |||
| + | a. Via Compex Firmware | ||
| + | *Put the AP in Firmware Upgrade mode and upload the file. | ||
| + | *This file is for WP543 with 4MB or 8MB NOR flash. | ||
| + | b. Via TFTP | ||
| + | *Go to the firmware upgrade mode (By pressing and hold the Reset button and plug-in the power adapter). | ||
| + | *Upload the OpenWRT image to the device (//$// **tftp -i 192.168.168.1 put openwrt-ar71xx-wp543.bin**) | ||
| + | ===== Wireless ===== | ||
| + | |||
| + | Both madwifi and ath9k work well with all Compex MiniPCI cards. You will need some wireless authenticator and/or supplicant (wpad-mini/wpad/wpa-supplicant/hostpad/hostapd-mini). | ||
| + | |||
| + | :!: Madwifi doesn't support MAC changes through UCI on this architecture. If you want to change of wireless MAC, see [[http://madwifi-project.org/wiki/UserDocs/ChangeMacAddress|this]]. | ||
| + | |||
| + | ===== Useful sources ===== | ||
| + | |||
| + | This page has been assembled from a number of different pages from the old wiki and the current wiki. Refer to them for more (possibly outdated) information. | ||
| + | |||
| + | *<del>[[http://www.compex.com.sg/forum/|Compex forum]]</del> \\ | ||
| + | *<del>[[http://cpx.px.cz/|Another Compex forum (CZ/ENG)]]</del> | ||
| + | |||
| + | ===== Tags ===== | ||
| + | [[meta:tags|How to add tags]] | ||
| + | {{tag>AR7161}} | ||
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 3.0 Unported
