User Tools

Site Tools


toh:comtrend:ar5381u

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
toh:comtrend:ar5381u [2012/11/15 02:21]
toh:comtrend:ar5381u [2016/05/11 14:29] (current)
danitool [LEDs]
Line 1: Line 1:
 +====== Comtrend AR-5381u ======
  
 +[[http://​us.comtrend.com/​products/​public/​product/​ipv-6/​ar-5381u.html|AR-5381u OEM website]]
 +
 +{{:​media:​comtrend:​ar-5381u.png?​0x200|}}
 +
 +
 +===== Supported Versions =====
 +
 +Supported since [[https://​dev.openwrt.org/​changeset/​33895|R33895]].
 +
 +<color crimson>
 +ADSL NOT SUPPORTED
 +</​color>​
 +
 +^ Firmware ^ download link ^ notes ^
 +| Trunk | https://​downloads.openwrt.org/​snapshots/​trunk/​brcm63xx/​generic/​openwrt-brcm63xx-generic-AR-5381u-squashfs-cfe.bin | LuCI web interface not installed |
 +| Chaos Calmer ​ 15.05 | https://​downloads.openwrt.org/​chaos_calmer/​15.05/​brcm63xx/​generic/​openwrt-15.05-brcm63xx-generic-AR-5381u-squashfs-cfe.bin | |
 +| Barrier Breaker 14.07 | https://​downloads.openwrt.org/​barrier_breaker/​14.07/​brcm63xx/​generic/​openwrt-AR-5381u-squashfs-cfe.bin | wifi unsupported |
 +
 +===== Installation =====
 +==== Flashing ANY Firmware ====
 +You must set your TCP/IP v4 protocol at your computer to:
 +  - IP: 192.168.1.2
 +  - Netmask: 255.255.255.0
 +  - Gateway: 192.168.1.1
 +  - DNS: (optional, can be blank).
 +Then:
 +  - Power off the router.
 +  - Press reset button near the antenna.
 +  - Keep it pressed while powering up during ~20+ seconds.
 +  - Acces to http://​192.168.1.1 and upload binary file.
 +  - Wait until router reboots.
 +
 +
 +===== Specific Configuration =====
 +==== Interfaces ====
 +
 +The default network configuration is:
 +^ Interface Name   ^ Description ​         ^ Default configuration ​  ^
 +| br-lan ​          | LAN & WiFi           | 192.168.1.1/​24 ​         |
 +| eth0             | LAN ports (0 to 3)   | bridged ​                |
 +| wlan0            | WiFi                 | bridged (disabled) ​     |
 +
 +==== Switch Ports (for VLANs) ====
 +This is an example to configure the switch: numbers 0-2 will be lan, labeled as Ports LAN1X, LAN2X, LAN3X on the unit, number 3 (LAN4X) will be the Internet (WAN), 8 is the internal connection to the router itself. Don't be fooled: vlan1 = eth0.1, vlan2 = eth0.2 and so on.
 +^ Port    ^ Switch port   ^ Mode             ^
 +| LAN1X   | 0             | lan              |
 +| LAN2X   | 1             | lan              |
 +| LAN3X   | 2             | lan              |
 +| LAN4X   | 3             | Internet (WAN)   |
 +
 +<​code># ​
 +config interface '​loopback'​
 +        option ifname '​lo'​
 +        option proto '​static'​
 +        option ipaddr '​127.0.0.1'​
 +        option netmask '​255.0.0.0'​
 +
 +config globals '​globals'​
 +        option ula_prefix '​fda5:​ace8:​376d::/​48'​
 +
 +config interface '​lan'​
 +        option ifname '​eth0.1'​
 +        option type '​bridge'​
 +        option proto '​static'​
 +        option ipaddr '​192.168.1.1'​
 +        option netmask '​255.255.255.0'​
 +        option ip6assign '​60'​
 +
 +config interface '​wan'​
 +        option ifname '​eth0.2'​
 +        option proto '​dhcp'​
 +        ​
 +config switch
 +        option name '​eth0'​
 +        option reset '​1'​
 +        option enable_vlan '​1'​
 +
 +config switch_vlan
 +        option device '​eth0'​
 +        option vlan '​1'​
 +        option ports '0 1 2 8t'
 +
 +config switch_vlan
 +        option device '​eth0'​
 +        option vlan '​2'​
 +        option ports '3 8t'
 +</​code>​
 +
 +
 +
 +===== Hardware =====
 +==== Info ====
 +| **[[wp>​Instruction set|Instruction set]]:​** ​ | [[wp>​MIPS architecture|MIPS]] |
 +| **Vendor:​** ​                     | [[wp>​Broadcom]] |
 +| **[[doc:​techref:​Bootloader]]:​** ​ | [[doc:​techref:​bootloader:​CFE]] |
 +| **Board ID:**                    | 96328A-1241N |
 +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​ | Broadcom BCM6328 |
 +| **[[doc:​hardware:​cpu|CPU]] @Frq** ​        | BMIPS4350 V7.5 @320 MHz |
 +| **Flash-Chip:​** ​ | MX25L12845EMI-10G (SPI) / 64KB block size x 256 main blocks |
 +| **Flash size** ​  | 16 MiB |
 +| **RAM-Chip** ​    | [[http://​pdf1.alldatasheet.com/​datasheet-pdf/​view/​312992/​ETRON/​EM68B16CWPA-25H.html|EM68B16CWPA-25H]] / DDR2-800 |
 +| **RAM size** ​    | 64 MiB |
 +| **Wireless** ​    | BCM43225 (14e4:a8d8) 802.11b/g/n (onboard) |
 +| **Ethernet:​** ​   | Internal BRCM6328 Switch, 4x 100M + ADSL2+ |
 +| **USB** ​         | 1x 2.0 |
 +| **[[doc:​hardware:​port.serial|Serial]]:​** ​ | [[#​Serial|Yes]] ​  |
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​     | [[#​JTAG|?​]] ​      |
 +
 +==== Photos ====
 +Photo of front and back of the casing:
 +
 +FIXME
 +
 +=== Opening the case ===
 +Note: This will void your warranty! ​
 +
 +  * To remove the cover do a/b/c
 +
 +**Main PCB:**
 +
 +{{media:​comtrend:​ar-5381u_board_up.jpg?​0x400}} {{media:​comtrend:​ar-5381u_board_down.jpg?​0x400}}
 +
 +
 +==== Wifi ====
 +**BCM43225** 802.11b/g/n onboard wifi, 2x PCB non-detachable antennas inside the case. 
 +
 +No physical EEPROM at the board, nor partition reserverd for this data at the flash chip. In theory, in the original firmware, the EEPROM is taken from the file ///​etc/​wlan/​bcm43225_map.bin//,​ although some bytes differ when comparing with wlctl dumps.
 +
 +Dumps from the OEM firmware:
 +<WRAP bootlog>
 +<​nowiki>​ > > wlctl revinfo
 +vendorid 0x14e4
 +deviceid 0x4357
 +radiorev 0xb2056000
 +chipnum 0xa8d9
 +chiprev 0x1
 +chippackage 0xa
 +corerev 0x17
 +boardid 0xa8d8
 +boardvendor 0x14e4
 +boardrev P200
 +driverrev 0x5647b00
 +ucoderev 0x2930000
 +bus 0x1
 +phytype 0x4
 +phyrev 0x6
 +anarev 0x0
 + > wlctl srdump ​
 +
 +  srom[000]: ​ 0x2801 ​ 0x0000 ​ 0x04da ​ 0x14e4 ​ 0x0078 ​ 0xedbe ​ 0x0000 ​ 0x2bc4  ​
 +  srom[008]: ​ 0x2a64 ​ 0x2964 ​ 0x2c64 ​ 0x3ce7 ​ 0x46ff ​ 0x47ff ​ 0x0c00 ​ 0x0820  ​
 +  srom[016]: ​ 0x0030 ​ 0x1002 ​ 0x9f28 ​ 0x5d44 ​ 0x8080 ​ 0x1d8f ​ 0x0032 ​ 0x0100  ​
 +  srom[024]: ​ 0xdf00 ​ 0x71f5 ​ 0x8400 ​ 0x0083 ​ 0x8500 ​ 0x2010 ​ 0x0001 ​ 0xffff  ​
 +  srom[032]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[040]: ​ 0xffff ​ 0xffff ​ 0x1008 ​ 0x0005 ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[048]: ​ 0x4357 ​ 0x8000 ​ 0x0002 ​ 0x0000 ​ 0x1f30 ​ 0x1800 ​ 0x0000 ​ 0x0000  ​
 +  srom[056]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[064]: ​ 0x5372 ​ 0x1200 ​ 0x0200 ​ 0x0000 ​ 0x1000 ​ 0x0000 ​ 0x0000 ​ 0x0000  ​
 +  srom[072]: ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x88ff ​ 0xffff ​ 0xffff ​ 0x0303 ​ 0x0202  ​
 +  srom[080]: ​ 0xffff ​ 0x0033 ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0x0325  ​
 +  srom[088]: ​ 0xffff ​ 0x7800 ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[096]: ​ 0x204e ​ 0xfed6 ​ 0x172e ​ 0xfaab ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[104]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[112]: ​ 0x204e ​ 0xfecc ​ 0x1665 ​ 0xfaac ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[120]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[128]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[136]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[144]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[152]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[160]: ​ 0x0000 ​ 0x5555 ​ 0x5555 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000  ​
 +  srom[168]: ​ 0x0000 ​ 0x5555 ​ 0x7555 ​ 0x5555 ​ 0x7555 ​ 0x5555 ​ 0x7555 ​ 0x5555  ​
 +  srom[176]: ​ 0x7555 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000  ​
 +  srom[184]: ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000  ​
 +  srom[192]: ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000  ​
 +  srom[200]: ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0002 ​ 0x0000 ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[208]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[216]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0x0008  ​
 + > wlctl nvram_dump
 +sromrev=8
 +boardrev=0x1200
 +boardflags=0x200
 +boardflags2=0x1000
 +boardtype=0x4da
 +boardnum=0
 +regrev=0
 +ledbh1=136
 +pa0b0=0xfed6
 +pa0b1=0x172e
 +pa0b2=0xfaab
 +pa0itssit=32
 +pa0maxpwr=78
 +opo=85
 +aa2g=3
 +aa5g=3
 +ag0=2
 +ag1=2
 +ag2=255
 +ag3=255
 +pa1b0=0xffff
 +pa1b1=0xffff
 +pa1b2=0xffff
 +pa1lob0=0xffff
 +pa1lob1=0xffff
 +pa1lob2=0xffff
 +pa1hib0=0xffff
 +pa1hib1=0xffff
 +pa1hib2=0xffff
 +pa1itssit=255
 +pa1maxpwr=255
 +pa1lomaxpwr=255
 +pa1himaxpwr=255
 +bxa2g=3
 +rssisav2g=7
 +rssismc2g=15
 +rssismf2g=15
 +bxa5g=3
 +rssisav5g=7
 +rssismc5g=15
 +rssismf5g=15
 +tri2g=255
 +tri5g=255
 +tri5gl=255
 +tri5gh=255
 +rxpo2g=-1
 +rxpo5g=-1
 +txchain=3
 +rxchain=3
 +antswitch=0
 +tssipos2g=1
 +extpagain2g=2
 +pdetrange2g=4
 +triso2g=3
 +antswctl2g=0
 +tssipos5g=1
 +extpagain5g=3
 +pdetrange5g=31
 +triso5g=7
 +antswctl5g=31
 +ccode=
 +macaddr=38:​72:​c0:​99:​54:​7e
 +tempthresh=120
 +tempoffset=0
 +rawtempsense=0x1ff
 +measpower=0x7f
 +tempsense_slope=0xff
 +tempcorrx=0x3f
 +tempsense_option=0x3
 +freqoffset_corr=0xf
 +iqcal_swp_dis=0x1
 +hw_iqcal_en=0x1
 +elna2g=255
 +elna5g=255
 +phycal_tempdelta=255
 +temps_period=15
 +temps_hysteresis=15
 +measpower1=0x7f
 +measpower2=0x7f
 +cck2gpo=0
 +ofdm2gpo=1431655765
 +ofdm5gpo=0
 +ofdm5glpo=0
 +ofdm5ghpo=0
 +mcs2gpo0=21845
 +mcs2gpo1=30037
 +mcs2gpo2=21845
 +mcs2gpo3=30037
 +mcs2gpo4=21845
 +mcs2gpo5=30037
 +mcs2gpo6=21845
 +mcs2gpo7=30037
 +mcs5gpo0=0
 +mcs5gpo1=0
 +mcs5gpo2=0
 +mcs5gpo3=0
 +mcs5gpo4=0
 +mcs5gpo5=0
 +mcs5gpo6=0
 +mcs5gpo7=0
 +mcs5glpo0=0
 +mcs5glpo1=0
 +mcs5glpo2=0
 +mcs5glpo3=0
 +mcs5glpo4=0
 +mcs5glpo5=0
 +mcs5glpo6=0
 +mcs5glpo7=0
 +mcs5ghpo0=0
 +mcs5ghpo1=0
 +mcs5ghpo2=0
 +mcs5ghpo3=0
 +mcs5ghpo4=0
 +mcs5ghpo5=0
 +mcs5ghpo6=0
 +mcs5ghpo7=0
 +cddpo=0
 +stbcpo=0
 +bw40po=2
 +bwduppo=0
 +pcieingress_war=15
 +rxgainerr2ga0=63
 +rxgainerr2ga1=31
 +rxgainerr2ga2=31
 +rxgainerr5gla0=63
 +rxgainerr5gla1=31
 +rxgainerr5gla2=31
 +rxgainerr5gma0=63
 +rxgainerr5gma1=31
 +rxgainerr5gma2=31
 +rxgainerr5gha0=63
 +rxgainerr5gha1=31
 +rxgainerr5gha2=31
 +rxgainerr5gua0=63
 +rxgainerr5gua1=31
 +rxgainerr5gua2=31
 +noiselvl2ga0=31
 +noiselvl2ga1=31
 +noiselvl2ga2=31
 +noiselvl5gla0=31
 +noiselvl5gla1=31
 +noiselvl5gla2=31
 +noiselvl5gma0=31
 +noiselvl5gma1=31
 +noiselvl5gma2=31
 +noiselvl5gha0=31
 +noiselvl5gha1=31
 +noiselvl5gha2=31
 +noiselvl5gua0=31
 +noiselvl5gua1=31
 +noiselvl5gua2=31
 +maxp2ga0=78
 +itt2ga0=32
 +itt5ga0=255
 +pa2gw0a0=0xfed6
 +pa2gw1a0=0x172e
 +pa2gw2a0=0xfaab
 +maxp5ga0=255
 +maxp5gha0=255
 +maxp5gla0=255
 +pa5gw0a0=0xffff
 +pa5gw1a0=0xffff
 +pa5gw2a0=0xffff
 +pa5glw0a0=0xffff
 +pa5glw1a0=0xffff
 +pa5glw2a0=0xffff
 +pa5ghw0a0=0xffff
 +pa5ghw1a0=0xffff
 +pa5ghw2a0=0xffff
 +maxp2ga1=78
 +itt2ga1=32
 +itt5ga1=255
 +pa2gw0a1=0xfecc
 +pa2gw1a1=0x1665
 +pa2gw2a1=0xfaac
 +maxp5ga1=255
 +maxp5gha1=255
 +maxp5gla1=255
 +pa5gw0a1=0xffff
 +pa5gw1a1=0xffff
 +pa5gw2a1=0xffff
 +pa5glw0a1=0xffff
 +pa5glw1a1=0xffff
 +pa5glw2a1=0xffff
 +pa5ghw0a1=0xffff
 +pa5ghw1a1=0xffff
 +pa5ghw2a1=0xffff
 +maxp2ga2=255
 +itt2ga2=255
 +itt5ga2=255
 +pa2gw0a2=0xffff
 +pa2gw1a2=0xffff
 +pa2gw2a2=0xffff
 +maxp5ga2=255
 +maxp5gha2=255
 +maxp5gla2=255
 +pa5gw0a2=0xffff
 +pa5gw1a2=0xffff
 +pa5gw2a2=0xffff
 +pa5glw0a2=0xffff
 +pa5glw1a2=0xffff
 +pa5glw2a2=0xffff
 +pa5ghw0a2=0xffff
 +pa5ghw1a2=0xffff
 +pa5ghw2a2=0xffff
 +maxp2ga3=255
 +itt2ga3=255
 +itt5ga3=255
 +pa2gw0a3=0xffff
 +pa2gw1a3=0xffff
 +pa2gw2a3=0xffff
 +maxp5ga3=255
 +maxp5gha3=255
 +maxp5gla3=255
 +pa5gw0a3=0xffff
 +pa5gw1a3=0xffff
 +pa5gw2a3=0xffff
 +pa5glw0a3=0xffff
 +pa5glw1a3=0xffff
 +pa5glw2a3=0xffff
 +pa5ghw0a3=0xffff
 +pa5ghw1a3=0xffff
 +pa5ghw2a3=0xffff
 +devid=0x4357
 +
 + ></​nowiki>​
 +</​WRAP>​\\
 +
 +
 +==== JTAG ====
 +-> [[doc:​hardware:​port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +N/A
 +
 +==== Serial ====
 +-> [[doc:​hardware:​port.serial]] general information about the serial port, serial port cable, etc.
 +
 +How to connect to the Serial Port of this specific device:\\
 +{{media:​comtrend:​ar-5381u_board_serial.jpg?​500x300}}
 +
 +**Photo of PCB with markings**
 +
 +===== GPIO =====
 +==== LEDs ====
 +Read: [[doc:​uci:​system#​leds|System configuration:​ Leds]] to configure the leds
 +^ Pin   ^ Event           ^ Active ​  ^ Soldered ​  ^
 +| 2     | ALARM (red)     | Low      | Yes        |
 +| 3     | ADSL (green) ​   | Low      | Yes        |
 +| 4     | Power (green) ​  | Low      | Yes        |
 +| 5     | wps             | Low      | No         |
 +| 8     | power (red)     | Low      | No         |
 +| 11    | alarm (green) ​  | Low      | No         |
 +
 +==== Buttons ====
 +-> [[doc:​howto:​hardware.button]] on howto use and configure the hardware button(s).
 +^ Pin   ^ Event     ^ Active ​  ^ Soldered ​  ^
 +| 23    | Reset     | Low      | Yes        |
 +| 24    | Extra 1   | Low      | No         |
 +| 31    | Extra 2   | Low      | No         |
 +
 +===== Bootlogs =====
 +==== OEM Bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​CFE version 1.0.37-106.5-9 for BCM96328 (32bit,​SP,​BE)
 +Build Date: 2010-12-20 22:52:56 (tony@broadcom_eu)
 +Copyright (C) 2000-2009 Broadcom Corporation.
 +
 +HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
 +Total Flash size: 16384K with 256 sectors
 +Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 67108864 bytes (64MB)
 +Boot Address: 0xb8000000
 +
 +Board IP address ​                 : 192.168.1.1:​ffffff00  ​
 +Host IP address ​                  : 192.168.1.100  ​
 +Gateway IP address ​               :   
 +Run from flash/host (f/h)         : f  ​
 +Default host run file name        : vmlinux  ​
 +Default host flash file name      : bcm963xx_fs_kernel  ​
 +Boot delay (0-9 seconds) ​         : 1  ​
 +Boot image (0=latest, 1=previous) : 0  ​
 +Board Id (0-5)                    : 96328A-1241N  ​
 +Number of MAC Addresses (1-32) ​   : 11  ​
 +Base MAC Address ​                 : 11:​22:​33:​44:​55:​66
 +PSI Size (1-64) KBytes ​           : 24  ​
 +Enable Backup PSI [0|1]           : 0  ​
 +System Log Size (0-256) KBytes ​   : 0  ​
 +Main Thread Number [0|1]          : 0  ​
 +Serial Number ​                    : ​  
 +Default PSK key                   : xxxxxxxxxxxxxxxxx  ​
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 110
 +Booting from latest image (0xb8010000) ...
 +Code Address: 0x80010000, Entry Address: 0x80292f40
 +Decompression OK!
 +Entry at 0x80292f40
 +Closing network.
 +Disabling Switch ports.
 +Flushing Receive Buffers...
 +0 buffers found.
 +Closing DMA Channels.
 +Starting program at 0x80292f40
 +Linux version 2.6.30 (lucien@localhost.localdomain) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #3 Fri Oct 28 13:22:45 CST 2011
 +
 +HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
 +
 +96328A-1241N prom init
 +
 +CPU revision is: 0002a075 (Broadcom4350)
 +
 +Determined physical RAM map:
 +
 + ​memory:​ 03f00000 @ 00000000 (usable)
 +
 +Zone PFN ranges:
 +
 +  DMA      0x00000000 -> 0x00001000
 +
 +  Normal ​  ​0x00001000 -> 0x00003f00
 +
 +Movable zone start PFN for each node
 +
 +early_node_map[1] active PFN ranges
 +
 +    0: 0x00000000 -> 0x00003f00
 +
 +On node 0 totalpages: 16128
 +
 +free_area_init_node:​ node 0, pgdat 8031cf10, node_mem_map 81000000
 +
 +  DMA zone: 32 pages used for memmap
 +
 +  DMA zone: 0 pages reserved
 +
 +  DMA zone: 4064 pages, LIFO batch:0
 +
 +  Normal zone: 94 pages used for memmap
 +
 +  Normal zone: 11938 pages, LIFO batch:1
 +
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16002
 +
 +Kernel command line: root=31:0 ro noinitrd console=ttyS0,​115200
 +
 +wait instruction:​ enabled
 +
 +Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +
 +Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +
 +NR_IRQS:128
 +
 +PID hash table entries: 256 (order: 8, 1024 bytes)
 +
 +console [ttyS0] enabled
 +
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +
 +Memory: 60384k/​64512k available (2595k kernel code, 4108k reserved, 533k data, 124k init, 0k highmem)
 +
 +Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
 +
 +Mount-cache hash table entries: 512
 +
 +--Kernel Config--
 +
 +  SMP=0
 +
 +  PREEMPT=0
 +
 +  DEBUG_SPINLOCK=0
 +
 +  DEBUG_MUTEXES=0
 +
 +Broadcom Logger v0.1 Oct 28 2011 13:07:23
 +
 +net_namespace:​ 812 bytes
 +
 +NET: Registered protocol family 16
 +
 +Total Flash size: 16384K with 4096 sectors
 +
 +registering PCI controller with io_map_base unset
 +
 +registering PCI controller with io_map_base unset
 +
 +bio: create slab <​bio-0>​ at 0
 +
 +SCSI subsystem initialized
 +
 +usbcore: registered new interface driver usbfs
 +
 +usbcore: registered new interface driver hub
 +
 +usbcore: registered new device driver usb
 +
 +pci 0000:​00:​09.0:​ reg 10 32bit mmio: [0x10002600-0x100026ff]
 +
 +pci 0000:​00:​0a.0:​ reg 10 32bit mmio: [0x10002500-0x100025ff]
 +
 +pci 0000:​01:​00.0:​ PME# supported from D0 D3hot
 +
 +pci 0000:​01:​00.0:​ PME# disabled
 +
 +pci 0000:​02:​00.0:​ reg 10 64bit mmio: [0x000000-0x003fff]
 +
 +pci 0000:​02:​00.0:​ supports D1 D2
 +
 +pci 0000:​01:​00.0:​ PCI bridge, secondary bus 0000:02
 +
 +pci 0000:​01:​00.0: ​  IO window: disabled
 +
 +pci 0000:​01:​00.0: ​  MEM window: 0x10f00000-0x10ffffff
 +
 +pci 0000:​01:​00.0: ​  ​PREFETCH window: disabled
 +
 +PCI: Enabling device 0000:​01:​00.0 (0000 -> 0002)
 +
 +PCI: Setting latency timer of device 0000:​01:​00.0 to 64
 +
 +BLOG v3.0 Initialized
 +
 +BLOG Rule v1.0 Initialized
 +
 +Broadcom IQoS v0.1 Oct 28 2011 13:09:14 initialized
 +
 +NET: Registered protocol family 8
 +
 +NET: Registered protocol family 20
 +
 +NET: Registered protocol family 2
 +
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +
 +TCP: Hash tables configured (established 2048 bind 2048)
 +
 +TCP reno registered
 +
 +NET: Registered protocol family 1
 +
 +squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +
 +squashfs: version 4.0 with LZMA457 ported by BRCM
 +
 +fuse init (API version 7.11)
 +
 +msgmni has been set to 117
 +
 +io scheduler noop registered (default)
 +
 +pcieport-driver 0000:​01:​00.0:​ device [14e4:6328] has invalid IRQ; check vendor BIOS
 +
 +PCI: Setting latency timer of device 0000:​01:​00.0 to 64
 +
 +Driver '​sd'​ needs updating - please use bus_type methods
 +
 +PPP generic driver version 2.4.2
 +
 +PPP Deflate Compression module registered
 +
 +PPP BSD Compression module registered
 +
 +NET: Registered protocol family 24
 +
 +bcm963xx_mtd driver v1.0
 +
 +File system address: 0xb8010100
 +
 +ehci_hcd: USB 2.0 '​Enhanced'​ Host Controller (EHCI) Driver
 +
 +PCI: Enabling device 0000:​00:​0a.0 (0000 -> 0002)
 +
 +PCI: Setting latency timer of device 0000:​00:​0a.0 to 64
 +
 +ehci_hcd 0000:​00:​0a.0:​ EHCI Host Controller
 +
 +ehci_hcd 0000:​00:​0a.0:​ new USB bus registered, assigned bus number 1
 +
 +ehci_hcd 0000:​00:​0a.0:​ Enabling legacy PCI PM
 +
 +ehci_hcd 0000:​00:​0a.0:​ irq 50, io mem 0x10002500
 +
 +ehci_hcd 0000:​00:​0a.0:​ USB f.f started, EHCI 1.00
 +
 +usb usb1: configuration #1 chosen from 1 choice
 +
 +hub 1-0:1.0: USB hub found
 +
 +hub 1-0:1.0: 1 port detected
 +
 +ohci_hcd: USB 1.1 '​Open'​ Host Controller (OHCI) Driver
 +
 +PCI: Enabling device 0000:​00:​09.0 (0000 -> 0002)
 +
 +PCI: Setting latency timer of device 0000:​00:​09.0 to 64
 +
 +ohci_hcd 0000:​00:​09.0:​ OHCI Host Controller
 +
 +ohci_hcd 0000:​00:​09.0:​ new USB bus registered, assigned bus number 2
 +
 +ohci_hcd 0000:​00:​09.0:​ irq 49, io mem 0x10002600
 +
 +usb usb2: configuration #1 chosen from 1 choice
 +
 +hub 2-0:1.0: USB hub found
 +
 +hub 2-0:1.0: 1 port detected
 +
 +usbcore: registered new interface driver usblp
 +
 +Initializing USB Mass Storage driver...
 +
 +usbcore: registered new interface driver usb-storage
 +
 +USB Mass Storage support registered.
 +
 +brcmboard: brcm_board_init entry
 +
 +SES: Button Interrupt 0x1 is enabled
 +
 +SES: LED GPIO 0x8009 is enabled
 +
 +Serial: BCM63XX driver $Revision: 3.00 $
 +
 +ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
 +
 +ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
 +
 +Total # RxBds=948
 +
 +bcmPktDmaBds_init:​ Broadcom Packet DMA BDs initialized
 +
 +
 +bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Oct 28 2011 13:08:56
 +
 +GACT probability NOT on
 +
 +Mirror/​redirect action on
 +
 +u32 classifier
 +
 +    input device check on 
 +
 +    Actions configured ​
 +
 +TCP cubic registered
 +
 +Initializing XFRM netlink socket
 +
 +NET: Registered protocol family 17
 +
 +NET: Registered protocol family 15
 +
 +Initializing MCPD Module
 +
 +Ebtables v2.0 registered
 +
 +ebt_time registered
 +
 +ebt_ftos registered
 +
 +ebt_wmm_mark registered
 +
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​
 +
 +All bugs added by David S. Miller <​davem@redhat.com>​
 +
 +VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
 +
 +Freeing unused kernel memory: 124k freed
 +
 +
 +init started: ​ BusyBox v1.00 (2011.10.28-05:​10+0000) multi-call binary
 +
 +
 +BusyBox v1.00 (2011.10.28-05:​10+0000) Built-in shell (msh)
 +Enter '​help'​ for a list of built-in commands.
 +
 +
 +Loading drivers and kernel modules... ​
 +
 +pktflow: module license '​Proprietary'​ taints kernel.
 +
 +Disabling lock debugging due to kernel taint
 +
 +[0;​36;​44mInitialized fcache state
 +
 +Broadcom Packet Flow Cache  Char Driver v2.2 Oct 28 2011 13:07:54 Registered<​242>​
 +
 +Created Proc FS /​procfs/​fcache
 +
 +Broadcom Packet Flow Cache registered with netdev chain
 +
 +[0;​36;​44mBroadcom Packet Flow Cache learning via BLOG enabled.
 +
 +Constructed Broadcom Packet Flow Cache v2.2 Oct 28 2011 13:07:54
 +
 +bcmxtmcfg: bcmxtmcfg_init entry
 +
 +adsl: adsl_init entry
 +
 +Broadcom BCM6328B0 Ethernet Network Device v0.1 Oct 28 2011 13:08:52
 +
 +ETH Init: Ch:0 - 180 tx BDs at 0xa395a000
 +
 +ETH Init: Ch:1 - 180 tx BDs at 0xa3a25000
 +
 +ETH Init: Ch:0 - 400 rx BDs at 0xa3a24000
 +
 +ETH Init: Ch:1 - 100 rx BDs at 0xa3a2b800
 +
 +dgasp: kerSysRegisterDyingGaspHandler:​ bcmsw registered ​
 +
 +eth0: MAC Address: 11:​22:​33:​44:​55:​66
 +
 +eth1: MAC Address: 11:​22:​33:​44:​55:​66
 +
 +eth2: MAC Address: 11:​22:​33:​44:​55:​66
 +
 +eth3: MAC Address: 11:​22:​33:​44:​55:​66
 +
 +BCM63XX_USB USB Device not present
 +
 +insmod: cannot insert `/​lib/​modules/​2.6.30/​extra/​bcm_usb.ko':​ Success (19): Success
 +PCI: Enabling device 0000:​02:​00.0 (0000 -> 0002)
 +
 +PCI: Setting latency timer of device 0000:​02:​00.0 to 64
 +
 +wl: passivemode=1
 +
 +wl: napimode=0
 +
 +wl: allocskbmode=1
 +
 +wl:srom strapped
 +
 +wl:(srom strapped) probe/​present=0
 +
 +wl:srom not detected, using main memory mapped srom info(wombo board)
 +
 +wl:loading /​etc/​wlan/​bcm43225_map.bin
 +
 +wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.100.123.0.cpe4.10L02.2
 +
 +dgasp: kerSysRegisterDyingGaspHandler:​ wl0 registered ​
 +
 +Broadcom 802.1Q VLAN Interface, v0.1
 +
 +
 +===== Comtrend Release Version A731-410JAZ-C05_R01 =====
 +
 +Auto-negotiation enabled.
 +Link is down
 +device eth0 entered promiscuous mode
 +
 +ip_tables: (C) 2000-2006 Netfilter Core Team
 +
 +Auto-negotiation enabled.
 +Link is down
 +device eth1 entered promiscuous mode
 +
 +Auto-negotiation enabled.
 +Link is down
 +device eth2 entered promiscuous mode
 +
 +Auto-negotiation enabled.
 +Link is down
 +device eth3 entered promiscuous mode
 +
 +device wl0 entered promiscuous mode
 +
 +br0: port 5(wl0) entering forwarding state
 +
 +BcmAdsl_Initialize=0xC00A9ED0,​ g_pFnNotifyCallback=0xC00D2C04
 +
 +WLmngr Daemon is running
 +optarg=0 shmId=0 ​
 +wlevt is ready for new msg...
 +pSdramPHY=0xA3FFFFF8,​ 0x0 0xFFFF0000
 +
 +*** XfaceOffset:​ 0x21F90 => 0x21F90 ***
 +
 +*** PhySdramSize got adjusted: 0x8339C => 0x98D48 ***
 +
 +AdslCoreSharedMemInit:​ shareMemAvailable=422544
 +
 +AdslCoreHwReset: ​ pLocSbSta=82dc8000 bkupThreshold=1600
 +
 +AdslCoreHwReset: ​ AdslOemDataAddr = 0xA3F783D4
 +
 +dgasp: kerSysRegisterDyingGaspHandler:​ dsl0 registered ​
 +
 +XTM Init: 400 rx BDs at 0xa3975000
 +
 +XTM Init: 16 rx BDs at 0xa2d8be80
 +
 +Register interface ppp0 !!
 +
 +iptables v1.4.0: can't initialize iptables table `nat': Table does not exist (do you need to insmod?)
 +Perhaps iptables or your kernel needs to be upgraded.
 +monitor task is initialized pid= 246 
 +
 +upnp:​error:​23.645:​process_smd_connection:​474:​cannot handle msg type 0x10000250
 +echo 005d0140 > /​proc/​switch
 +Comtrend polling daemon is running
 +Switch MDK: num_switches = 1
 +Switch MDK: unit = 0; phy_pbmp = 0xf; config_pbmp = 0xf 
 +Switch MDK link poll thread: unit=0; phypbmp=0xf
 +device wl0 left promiscuous mode
 +
 +br0: port 5(wl0) entering disabled state
 +
 +device wl0 entered promiscuous mode
 +
 +br0: port 5(wl0) entering forwarding state
 +
 +br0: port 5(wl0) entering disabled state
 +
 +There is no Predefined DevicePin in CFE
 +WPS Device PIN = 00000000
 +Setting SSID: "​Jazztel_xxxx"​
 +Setting SSID: "​wl0_Guest1"​
 +Setting SSID: "​wl0_Guest2"​
 +Setting SSID: "​wl0_Guest3"​
 +device wl0 left promiscuous mode
 +
 +br0: port 5(wl0) entering disabled state
 +
 +device wl0 entered promiscuous mode
 +
 +br0: port 5(wl0) entering forwarding state
 +
 +UPnP daemon is ready to run
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: scan in progress ...
 +acsd: selected channel spec: 0x2b01</​nowiki>​
 +</​WRAP>​\\
 +
 +==== OpenWrt ====
 +<WRAP bootlog>
 +<​nowiki>​[ ​   0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Sep 9 20:22:25 CEST 2012
 +[    0.000000] Detected Broadcom 0x6328 CPU revision 10b0
 +[    0.000000] CPU frequency is 320 MHz
 +[    0.000000] 64MB of RAM installed
 +[    0.000000] registering 32 GPIOs
 +[    0.000000] gpiochip_add:​ registered GPIOs 0 to 31 on device: bcm63xx-gpio
 +[    0.000000] board_bcm963xx:​ Boot address 0xb8000000
 +[    0.000000] board_bcm963xx:​ CFE version: 1.0.37-106.5
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
 +[    0.000000] board_bcm963xx:​ board name: 96328A-1241N
 +[    0.000000] Determined physical RAM map:
 +[    0.000000] ​ memory: 04000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone PFN ranges:
 +[    0.000000] ​  ​Normal ​  ​0x00000000 -> 0x00004000
 +[    0.000000] Movable zone start PFN for each node
 +[    0.000000] Early memory PFN ranges
 +[    0.000000] ​    0: 0x00000000 -> 0x00004000
 +[    0.000000] On node 0 totalpages: 16384
 +[    0.000000] free_area_init_node:​ node 0, pgdat 802acea0, node_mem_map 81000000
 +[    0.000000] ​  ​Normal zone: 128 pages used for memmap
 +[    0.000000] ​  ​Normal zone: 0 pages reserved
 +[    0.000000] ​  ​Normal zone: 16256 pages, LIFO batch:3
 +[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
 +[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 +[    0.000000] pcpu-alloc: [0] 0 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +[    0.000000] Kernel command line:  root=/​dev/​mtdblock2 rootfstype=squashfs,​jffs2 noinitrd console=ttyS0,​115200
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] Memory: 61808k/​65536k available (2262k kernel code, 3728k reserved, 415k data, 204k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
 +[    0.036000] pid_max: default: 32768 minimum: 301
 +[    0.040000] Mount-cache hash table entries: 512
 +[    0.048000] NET: Registered protocol family 16
 +[    0.276000] registering PCI controller with io_map_base unset
 +[    0.288000] bio: create slab <​bio-0>​ at 0
 +[    0.292000] PCI host bridge to bus 0000:00
 +[    0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
 +[    0.300000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
 +[    0.304000] pci 0000:​00:​00.0:​ [14e4:6328] type 1 class 0x000604
 +[    0.304000] pci 0000:​00:​00.0:​ PME# supported from D0 D3hot
 +[    0.304000] pci 0000:​01:​00.0:​ [14e4:a8d8] type 0 class 0x000280
 +[    0.304000] pci 0000:​01:​00.0:​ reg 10: [mem 0x00000000-0x00003fff 64bit]
 +[    0.304000] pci 0000:​01:​00.0:​ supports D1 D2
 +[    0.304000] pci 0000:​00:​00.0:​ BAR 8: assigned [mem 0x10f00000-0x10ffffff]
 +[    0.308000] pci 0000:​01:​00.0:​ BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
 +[    0.312000] pci 0000:​00:​00.0:​ PCI bridge to [bus 01-01]
 +[    0.316000] pci 0000:​00:​00.0: ​  ​bridge window [mem 0x10f00000-0x10ffffff]
 +[    0.320000] PCI: Enabling device 0000:​00:​00.0 (0000 -> 0002)
 +[    0.324000] Switching to clocksource MIPS
 +[    0.332000] PCI: Enabling device 0000:​01:​00.0 (0000 -> 0002)
 +[    0.340000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x08
 +[    0.344000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
 +[    0.356000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
 +[    0.364000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
 +[    0.372000] bcma: bus0: Found rev 6 PMU (capabilities 0x108C2606)
 +[    0.372000] bcma: bus0: PMU resource config unknown or not needed for device 0xA8D9
 +[    0.372000] bcma: bus0: Workarounds unknown or not needed for device 0xA8D9
 +[    0.404000] bcma: bus0: SPROM offset 0x800
 +[    0.444000] bcma: Reading SPROM failed. Trying fallback SPROM...
 +[    0.444000] bcm63xx_sprom_bcma:​ filled BCMA SPROM for chip id 0xa8d9
 +[    0.448000] bcma: bus0: Using SPROM revision 8 provided by platform.
 +[    0.448000] bcma: bus0: Bus registered
 +[    0.452000] NET: Registered protocol family 2
 +[    0.460000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.468000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +[    0.472000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.480000] TCP: Hash tables configured (established 2048 bind 2048)
 +[    0.488000] TCP reno registered
 +[    0.492000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.496000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.504000] NET: Registered protocol family 1
 +[    0.508000] PCI: CLS 0 bytes, default 16
 +[    0.512000] audit: initializing netlink socket (disabled)
 +[    0.516000] type=2000 audit(0.516:​1):​ initialized
 +[    0.524000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +[    0.528000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.540000] msgmni has been set to 120
 +[    0.544000] io scheduler noop registered
 +[    0.548000] io scheduler deadline registered (default)
 +[    0.556000] bcm63xx_uart.0:​ ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
 +[    0.564000] console [ttyS0] enabled, bootconsole disabled
 +[    0.580000] m25p80 spi0.0: found mx25l12805d,​ expected m25p80
 +[    0.588000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
 +[    0.592000] bcm63xxpart:​ CFE boot tag found with version 6 and board type 96328A-1241N
 +[    0.600000] bcm63xxpart:​ Partition 0 is CFE offset 0 and length 10000
 +[    0.608000] bcm63xxpart:​ Partition 1 is kernel offset 10100 and length eff00
 +[    0.612000] bcm63xxpart:​ Partition 2 is rootfs offset 100000 and length ef0000
 +[    0.620000] bcm63xxpart:​ Partition 3 is nvram offset ff0000 and length 10000
 +[    0.628000] bcm63xxpart:​ Partition 4 is linux offset 10000 and length fe0000
 +[    0.636000] bcm63xxpart:​ Spare partition is offset 340004 and length cafffc
 +[    0.644000] 5 bcm63xxpart partitions found on MTD device spi0.0
 +[    0.648000] Creating 5 MTD partitions on "​spi0.0":​
 +[    0.656000] 0x000000000000-0x000000010000 : "​CFE"​
 +[    0.660000] 0x000000010100-0x000000100000 : "​kernel"​
 +[    0.668000] mtd: partition "​kernel"​ must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    0.684000] 0x000000100000-0x000000ff0000 : "​rootfs"​
 +[    0.692000] mtd: partition "​rootfs"​ set to be root filesystem
 +[    0.696000] mtd: partition "​rootfs_data"​ created automatically,​ ofs=340000, len=CB0000 ​
 +[    0.704000] 0x000000340000-0x000000ff0000 : "​rootfs_data"​
 +[    0.712000] 0x000000ff0000-0x000001000000 : "​nvram"​
 +[    0.720000] 0x000000010000-0x000000ff0000 : "​linux"​
 +[    0.764000] bcm63xx-wdt bcm63xx-wdt: ​ started, timer margin: 30 sec
 +[    0.772000] TCP cubic registered
 +[    0.776000] NET: Registered protocol family 17
 +[    0.780000] 8021q: 802.1Q VLAN Support v1.8
 +[    0.792000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    0.804000] Freeing unused kernel memory: 204k freed
 +[    3.148000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link UP on Port 4, 100Mbps, full-duplex
 +[    3.384000] roboswitch: Probing device eth0: 
 +[    3.388000] bcm63xx_enet:​ could not find a used port with phy_id 0, assuming phy is external
 +[    3.400000] No Robo switch in managed mode found, phy_id = 0xffffffff
 +[    3.404000] roboswitch: Probing device eth1: No such device
 +[    3.412000] roboswitch: Probing device eth2: No such device
 +[    3.416000] roboswitch: Probing device eth3: No such device
 +[    5.940000] Button Hotplug driver version 0.4.1
 +[   ​12.632000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
 +[   ​12.640000] Backport based on wireless-testing.git master-2012-09-07
 +[   ​12.648000] compat.git: wireless-testing.git
 +[   ​12.708000] cfg80211: Calling CRDA to update world regulatory domain
 +[   ​12.712000] cfg80211: World regulatory domain updated:
 +[   ​12.720000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp)
 +[   ​12.728000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​12.736000] cfg80211: ​  ​(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   ​12.744000] cfg80211: ​  ​(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   ​12.752000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​12.760000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​13.152000] NET: Registered protocol family 10
 +[   ​13.596000] SCSI subsystem initialized
 +[   ​13.644000] There is already a switch registered on the device '​eth0'​
 +[   ​13.652000] roboswitch: Probing device eth1: No such device
 +[   ​13.656000] roboswitch: Probing device eth2: No such device
 +[   ​13.664000] roboswitch: Probing device eth3: No such device
 +[   ​13.940000] usbcore: registered new interface driver usbfs
 +[   ​13.948000] usbcore: registered new interface driver hub
 +[   ​13.956000] usbcore: registered new device driver usb
 +[   ​15.188000] NTFS driver 2.1.30 [Flags: R/O MODULE].
 +[   ​15.836000] PPP generic driver version 2.4.2
 +[   ​16.268000] brcmsmac bcma0:0: mfg 4bf core 812 rev 23 class 0 irq 31
 +[   ​16.616000] bcma: bus0: Switched to core: 0x812
 +[   ​16.620000] ieee80211 phy0: Selected rate control algorithm '​minstrel_ht'​
 +[   ​16.776000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​17.120000] NET: Registered protocol family 24
 +[   ​17.456000] ehci_hcd: USB 2.0 '​Enhanced'​ Host Controller (EHCI) Driver
 +[   ​17.568000] bcm63xx_ehci bcm63xx_ehci.0:​ BCM63XX integrated EHCI controller
 +[   ​17.572000] bcm63xx_ehci bcm63xx_ehci.0:​ new USB bus registered, assigned bus number 1
 +[   ​17.604000] bcm63xx_ehci bcm63xx_ehci.0:​ irq 50, io mem 0xb0002500
 +[   ​17.620000] bcm63xx_ehci bcm63xx_ehci.0:​ USB 2.0 started, EHCI 1.00, overcurrent ignored
 +[   ​17.628000] hub 1-0:1.0: USB hub found
 +[   ​17.632000] hub 1-0:1.0: 1 port detected
 +[   ​17.796000] nf_conntrack version 0.5.0 (968 buckets, 3872 max)
 +[   ​18.592000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​18.904000] ohci_hcd: USB 1.1 '​Open'​ Host Controller (OHCI) Driver
 +[   ​19.016000] bcm63xx_ohci bcm63xx_ohci.0:​ BCM63XX integrated OHCI controller
 +[   ​19.020000] bcm63xx_ohci bcm63xx_ohci.0:​ new USB bus registered, assigned bus number 2
 +[   ​19.028000] bcm63xx_ohci bcm63xx_ohci.0:​ irq 49, io mem 0xb0002600
 +[   ​19.096000] hub 2-0:1.0: USB hub found
 +[   ​19.100000] hub 2-0:1.0: 1 port detected
 +[   ​19.288000] Initializing USB Mass Storage driver...
 +[   ​19.292000] usbcore: registered new interface driver usb-storage
 +[   ​19.300000] USB Mass Storage support registered.
 +[   ​19.464000] usbcore: registered new interface driver ums-alauda
 +[   ​19.492000] usbcore: registered new interface driver ums-cypress
 +[   ​19.524000] usbcore: registered new interface driver ums-datafab
 +[   ​19.552000] usbcore: registered new interface driver ums-freecom
 +[   ​19.584000] usbcore: registered new interface driver ums-isd200
 +[   ​19.612000] usbcore: registered new interface driver ums-jumpshot
 +[   ​19.640000] usbcore: registered new interface driver ums-karma
 +[   ​19.672000] usbcore: registered new interface driver ums-sddr09
 +[   ​19.700000] usbcore: registered new interface driver ums-sddr55
 +[   ​19.732000] usbcore: registered new interface driver ums-usbat
 +[   ​24.320000] device eth0 entered promiscuous mode
 +[   ​24.324000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link UP on Port 4, 100Mbps, full-duplex
 +[   ​24.336000] br-lan: port 1(eth0) entered forwarding state
 +[   ​24.340000] br-lan: port 1(eth0) entered forwarding state
 +[   ​26.344000] br-lan: port 1(eth0) entered forwarding state
 +[   ​42.920000] jffs2_scan_eraseblock():​ End of filesystem marker found at 0x0
 +[   ​42.928000] jffs2_build_filesystem():​ unlocking the mtd device... done.
 +[   ​42.932000] jffs2_build_filesystem():​ erasing all blocks after the end marker...</​nowiki>​
 +</​WRAP>​\\
 +
 +===== Tags =====
 +[[meta:​tags|How to add tags]]
 +{{tag>​bcm63xx bcm6328 16flash 64ram}}