Supported since Barrier Breaker R33894.

Trunk: openwrt-96328A-1441N1-generic-squashfs-cfe.bin

You must set your TCP/IP v4 protocol to:

1. IP: 192.168.1.2
2. Netmask: 255.255.255.0
3. Gateway: 192.168.1.1
4. DNS: (optional, can be blank).

Then:

1. Power off the router.
2. Press reset button near the antenna.
3. Keep it pressed while powering up during ~20+ seconds.
4. Acces to http://192.168.1.1 and upload binary file.
5. Wait until router reboots.

→ port.jtag general information about the JTAG port, JTAG cable, etc.

N/A

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Photo of PCB with markings

Read: System configuration: Leds to configure the leds

→ hardware.button on howto use and configure the hardware button(s).

CFE version 1.0.37-110.11-2 for BCM96328 (32bit,SP,BE) Build Date: 2011-04-29 11:30:31 (lain@SW1-BCM-04) Copyright (C) 2000-2009 Broadcom Corporation. HS Serial flash device: name MX25L128, id 0xc218 size 16384KB Total Flash size: 16384K with 4096 sectors Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Boot image (0=latest, 1=previous) : 0 Board Id (0-6) : 96328A-1441N1 Number of MAC Addresses (1-32) : 32 Base MAC Address : fa:ba:da:fa:ba:da PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Serial Number : Default PSK key : *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Booting from latest image (0xb8010000) ... Code Address: 0x80010000, Entry Address: 0x80014230 Decompression OK! Entry at 0x80014230 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80014230 Linux version 2.6.30 (charles@SW1-BCM-04) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Wed May 4 19:58:12 CST 2011 HS Serial flash device: name MX25L128, id 0xc218 size 16384KB 96328A-1441N1 prom init CPU revision is: 0002a075 (Broadcom4350) Determined physical RAM map: memory: 03f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003f00 On node 0 totalpages: 16128 free_area_init_node: node 0, pgdat 8030ea80, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11938 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 wait instruction: enabled Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes RCU-based detection of stalled CPUs is enabled. NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 60504k/64512k available (2564k kernel code, 3988k reserved, 509k data, 120k init, 0k highmem) Calibrating delay loop... 319.48 BogoMIPS (lpj=159744) Mount-cache hash table entries: 512 net_namespace: 812 bytes NET: Registered protocol family 16 Total Flash size: 16384K with 256 sectors registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff] pci 0000:02:00.0: supports D1 D2 pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff pci 0000:01:00.0: PREFETCH window: disabled PCI: Enabling device 0000:01:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v2.1 Initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher squashfs: version 4.0 with LZMA457 ported by BRCM fuse init (API version 7.11) msgmni has been set to 118 io scheduler noop registered (default) pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 File system address: 0xb8010100 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0x8009 is enabled Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 36) is a BCM63XX bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 May 4 2011 19:57:46 Broadcom Logger v0.1 May 4 2011 19:57:31 Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 120k freed init started: BusyBox v1.00 (2011.05.04-11:58+0000) multi-call binary BusyBox v1.00 (2011.05.04-11:58+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... pktflow: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Broadcom Packet Flow Cache Char Driver v2.1 Mar 18 2010 21:39:51 Registered<242> NBUFF v1.0 Initialized Broadcom Packet Flow Cache learning via BLOG enabled. Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Constructed Broadcom Packet Flow Cache v2.1 Mar 18 2010 21:39:50 bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6328B0 Ethernet Network Device v0.1 May 4 2011 19:57:32 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered eth0: MAC Address: fa:ba:da:fa:ba:da eth1: MAC Address: fa:ba:da:fa:ba:da eth2: MAC Address: fa:ba:da:fa:ba:da eth3: MAC Address: fa:ba:da:fa:ba:da BCM63XX_USB USB Device not present insmod: cannot insert `/lib/modules/2.6.30/extra/bcm_usb.ko': Success (19): Success PCI: Enabling device 0000:02:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:02:00.0 to 64 wl:srom strapped wl:(srom strapped) probe/present=0 wl:srom not detected,using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm43225_map.bin wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.100.96.0.cpe4.406.0 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered Broadcom 802.1Q VLAN Interface, v0.1 ===== Comtrend Release Version A731-406JAZ-C02_R01 ===== rut_isApplicationRunning in rut_util.c eid = 24 rut_isApplicationRunning in rut_util.c eid = 24 Auto-negotiation enabled. Link is down device eth0 entered promiscuous mode ip_tables: (C) 2000-2006 Netfilter Core Team Auto-negotiation enabled. Link is down device eth1 entered promiscuous mode Auto-negotiation enabled. Link is down device eth2 entered promiscuous mode Auto-negotiation enabled. Link is down device eth3 entered promiscuous mode device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state BcmAdsl_Initialize=0xC00E2FEC, g_pFnNotifyCallback=0xC0106BE4 WLmngr Daemon is running optarg=0 shmId=0 wlevt_init@107: opened loopback socket 4 wlevt is ready for new msg... pSdramPHY=0xA3FFFFF8, 0xFFFFFFFF 0xFFFFFFFF AdslCoreSharedMemInit: shareMemAvailable=492320 AdslCoreHwReset: AdslOemDataAddr = 0xA3F691E4 dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered monitor task is initialized pid= 239 backup_psi_number_blk=0 result=24576 device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state br0: port 5(wl0) entering disabled state There is no Predefined DevicePin in CFE WPS Device PIN = 12345678 Setting SSID: "AR-5387un" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" wlctl: Not Permitted wlctl: Unsupported wlctl: Unsupported chanspec 0x2b06 selected 6 (0x2b06) br0: port 5(wl0) entering forwarding state device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state Reaped 759 UPnP daemon is ready to run BCM96328 Broadband Router Login:

[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Wed Jul 18 13:38:05 CEST 2012 [ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0 [ 0.000000] CPU frequency is 320 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] registering 32 GPIOs [ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm63xx-gpio [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.37-110.11 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350) [ 0.000000] board_bcm963xx: board name: 96328A-1441N1 [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00004000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00004000 [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 802a5a60, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Memory: 61864k/65536k available (2248k kernel code, 3672k reserved, 399k data, 200k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928) [ 0.036000] pid_max: default: 32768 minimum: 301 [ 0.040000] Mount-cache hash table entries: 512 [ 0.048000] NET: Registered protocol family 16 [ 0.276000] registering PCI controller with io_map_base unset [ 0.288000] bio: create slab at 0 [ 0.292000] PCI host bridge to bus 0000:00 [ 0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff] [ 0.300000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.304000] pci 0000:00:00.0: [14e4:6328] type 1 class 0x000604 [ 0.304000] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.304000] pci 0000:01:00.0: [14e4:a8d8] type 0 class 0x000280 [ 0.304000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00003fff 64bit] [ 0.304000] pci 0000:01:00.0: supports D1 D2 [ 0.304000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff] [ 0.308000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit] [ 0.312000] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 0.316000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff] [ 0.320000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 0.324000] Switching to clocksource MIPS [ 0.332000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 0.340000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x0A [ 0.344000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0) [ 0.356000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0) [ 0.364000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0) [ 0.372000] bcma: bus0: Found rev 6 PMU (capabilities 0x108C2606) [ 0.372000] bcma: bus0: PMU resource config unknown or not needed for device 0xA8D9 [ 0.372000] bcma: bus0: Workarounds unknown or not needed for device 0xA8D9 [ 0.408000] bcma: bus0: SPROM offset 0x800 [ 0.448000] bcma: Reading SPROM failed. Trying fallback SPROM... [ 0.448000] bcma: bus0: Using SPROM revision 8 provided by platform. [ 0.448000] bcma: bus0: Bus registered [ 0.452000] NET: Registered protocol family 2 [ 0.456000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.464000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.472000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.480000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.484000] TCP reno registered [ 0.488000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.492000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.500000] NET: Registered protocol family 1 [ 0.504000] PCI: CLS 0 bytes, default 16 [ 0.508000] audit: initializing netlink socket (disabled) [ 0.512000] type=2000 audit(0.512:1): initialized [ 0.520000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.528000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.536000] msgmni has been set to 120 [ 0.540000] io scheduler noop registered [ 0.544000] io scheduler deadline registered (default) [ 0.552000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart [ 0.560000] console [ttyS0] enabled, bootconsole disabled [ 0.576000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.584000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.588000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328A-1441N1 [ 0.596000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000 [ 0.604000] bcm63xxpart: Partition 1 is kernel offset 10100 and length eff00 [ 0.612000] bcm63xxpart: Partition 2 is rootfs offset 100000 and length ef0000 [ 0.620000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000 [ 0.628000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000 [ 0.632000] bcm63xxpart: Spare partition is offset 2e0004 and length d0fffc [ 0.640000] 5 bcm63xxpart partitions found on MTD device spi0.0 [ 0.648000] Creating 5 MTD partitions on "spi0.0": [ 0.652000] 0x000000000000-0x000000010000 : "CFE" [ 0.660000] 0x000000010100-0x000000100000 : "kernel" [ 0.664000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.680000] 0x000000100000-0x000000ff0000 : "rootfs" [ 0.688000] mtd: partition "rootfs" set to be root filesystem [ 0.696000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=D10000 [ 0.704000] 0x0000002e0000-0x000000ff0000 : "rootfs_data" [ 0.712000] 0x000000ff0000-0x000001000000 : "nvram" [ 0.720000] 0x000000010000-0x000000ff0000 : "linux" [ 0.760000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.768000] TCP cubic registered [ 0.772000] NET: Registered protocol family 17 [ 0.776000] 8021q: 802.1Q VLAN Support v1.8 [ 0.788000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.796000] Freeing unused kernel memory: 200k freed [ 3.356000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex [ 3.412000] roboswitch: Probing device eth0: [ 3.416000] bcm63xx_enet: could not find a used port with phy_id 0, assuming phy is external [ 3.424000] No Robo switch in managed mode found, phy_id = 0xffffffff [ 3.432000] roboswitch: Probing device eth1: No such device [ 3.436000] roboswitch: Probing device eth2: No such device [ 3.444000] roboswitch: Probing device eth3: No such device [ 9.456000] JFFS2 notice: (319) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found. [ 12.652000] Compat-wireless backport release: compat-wireless-2012-07-13 [ 12.660000] Backport based on wireless-testing.git master-2012-07-16 [ 12.664000] compat.git: wireless-testing.git [ 12.728000] cfg80211: Calling CRDA to update world regulatory domain [ 12.732000] cfg80211: World regulatory domain updated: [ 12.740000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 12.748000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 12.756000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 12.764000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 12.772000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 12.780000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 13.184000] NET: Registered protocol family 10 [ 13.408000] SCSI subsystem initialized [ 13.464000] There is already a switch registered on the device 'eth0' [ 13.468000] roboswitch: Probing device eth1: No such device [ 13.476000] roboswitch: Probing device eth2: No such device [ 13.480000] roboswitch: Probing device eth3: No such device [ 13.744000] usbcore: registered new interface driver usbfs [ 13.748000] usbcore: registered new interface driver hub [ 13.756000] usbcore: registered new device driver usb [ 14.404000] b43-phy0: Broadcom 43225 WLAN found (core revision 23) [ 14.408000] bcma: bus0: Switched to core: 0x812 [ 14.412000] Broadcom 43xx driver loaded [ Features: PNL ] [ 14.612000] Button Hotplug driver version 0.4.1 [ 14.828000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 14.832000] Registered led device: b43-phy0::tx [ 14.832000] Registered led device: b43-phy0::rx [ 14.832000] Registered led device: b43-phy0::radio [ 15.468000] PPP generic driver version 2.4.2 [ 15.688000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 15.908000] NET: Registered protocol family 24 [ 16.052000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 16.096000] nf_conntrack version 0.5.0 (969 buckets, 3876 max) [ 16.544000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 16.896000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 16.956000] uhci_hcd: USB Universal Host Controller Interface driver [ 17.044000] Initializing USB Mass Storage driver... [ 17.048000] usbcore: registered new interface driver usb-storage [ 17.056000] USB Mass Storage support registered. [ 21.004000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex [ 21.012000] device eth0 entered promiscuous mode [ 21.020000] br-lan: port 1(eth0) entered forwarding state [ 21.024000] br-lan: port 1(eth0) entered forwarding state [ 23.028000] br-lan: port 1(eth0) entered forwarding state [ 23.260000] cfg80211: Calling CRDA for country: ES [ 23.264000] cfg80211: Regulatory domain changed to country: ES [ 23.272000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 23.280000] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 23.288000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 23.296000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 23.304000] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm) [ 24.760000] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07) [ 24.864000] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 27.408000] wlan0: authenticate with 11:22:33:44:55:66 [ 27.448000] wlan0: send auth to 11:22:33:44:55:66 (try 1/3) [ 27.456000] wlan0: authenticated [ 27.460000] b43 bcma0:0: wlan0: disabling HT as WMM/QoS is not supported [ 27.472000] wlan0: associate with 11:22:33:44:55:66 (try 1/3) [ 27.480000] wlan0: RX AssocResp from 11:22:33:44:55:66 (capab=0x411 status=0 aid=2) [ 27.488000] wlan0: associated [ 27.492000] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 38.016000] wlan0: no IPv6 routers present [ 150.012000] bcm63xx_enetsw bcm63xx_enetsw.0: link DOWN on Port 4 [ 265.016000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 2, 100Mbps, full-duplex