User Tools

Site Tools


toh:comtrend:ar5387un

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
toh:comtrend:ar5387un [2013/01/11 13:50]
toh:comtrend:ar5387un [2016/02/16 22:19] (current)
danitool [Other]
Line 1: Line 1:
 +====== Comtrend AR-5387un ======
  
 +{{:​media:​comtrend:​ar-5387un.png?​300&​nolink|}}
 +
 +
 +Supported since Barrier Breaker [[https://​dev.openwrt.org/​changeset/​33894|R33894]]. Internal ADSL modem NOT supported
 +
 +
 +===== Installation =====
 +
 +| Chaos Calmer (CC) | [[https://​downloads.openwrt.org/​chaos_calmer/​15.05/​brcm63xx/​generic/​openwrt-15.05-brcm63xx-generic-AR-5387un-squashfs-cfe.bin|openwrt-15.05-brcm63xx-generic-AR-5387un-squashfs-cfe.bin (CC)]] | |
 +| Barrier Breaker (BB) | [[https://​downloads.openwrt.org/​barrier_breaker/​14.07/​brcm63xx/​generic/​openwrt-AR-5387un-squashfs-cfe.bin|openwrt-AR-5387un-squashfs-cfe.bin (BB)]] | the wifi is not supported |
 +
 +
 +
 +==== Flashing ANY Firmware ====
 +You must set your TCP/IP v4 protocol to:
 +  - IP: 192.168.1.2
 +  - Netmask: 255.255.255.0
 +  - Gateway: 192.168.1.1
 +  - DNS: (optional, can be blank).
 +Then:
 +  - Power off the router.
 +  - Press reset button near the antenna.
 +  - Keep it pressed while powering up during ~20+ seconds.
 +  - Acces to http://​192.168.1.1 and upload binary file.
 +  - Wait until router reboots.
 +
 +
 +===== Hardware =====
 +==== Info ====
 +| **[[wp>​Instruction set|Instruction set]]:​** ​ | [[wp>​MIPS architecture|MIPS]] ​                   |
 +| **Vendor:​** ​                                 | [[wp>​Broadcom]] ​                                 |
 +| **[[doc:​techref:​Bootloader]]:​** ​             | [[doc:​techref:​bootloader:​CFE#​bcm63xx_cfe|CFE]] ​  |
 +| **Board ID:**                                | 96328A-1441N1 ​                                   |
 +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​ | Broadcom BCM6328 ​     |
 +| **[[doc:​hardware:​cpu|CPU]]/​Speed** ​       | BMIPS4350 / 320 MHz   |
 +| **Flash-Chip:​** ​  | MX25L128 ​                            |
 +| **Flash size** ​   | 16 MiB                               |
 +| **RAM-Chip** ​     | ProMOS V59C1512164QDJ25 / DDR2-800 ​  |
 +| **RAM size** ​     | 64 MiB                               |
 +| **Wireless** ​     | BCM43225 (14e4:a8d8) 802.11b/​g/​n ​    |
 +| **Antenna** ​      | 2x, non detachable ​                  |
 +| **Ethernet:​** ​    | Integrated BRCM6328 Switch ​          |
 +| **USB** ​          | yes                                  |
 +| **[[doc:​hardware:​port.serial|Serial]]:​** ​  | [[#​Serial|Yes]] ​  |
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​      | [[#​JTAG|?​]] ​      |
 +
 +==== Photos ====
 +
 +**Board**\\
 +{{media:​comtrend:​ar-5387un_board_t.jpg?​0x300}} {{media:​comtrend:​ar-5387un_board_b.jpg?​0x300}}
 +
 +==== Wifi ====
 +**BCM43225** 802.11b/g/n onboard wifi, 2x external non-detachable antennas outside the case. 
 +
 +No physical EEPROM at the board, nor partition reserverd for this data at the flash chip. In theory, in the original firmware, the EEPROM is taken from the file ///​etc/​wlan/​bcm43225_map.bin//,​ although some bytes differ comparing it wlctl dumps.
 +
 +Dumps from the OEM firmware:
 +<WRAP bootlog>
 +<​nowiki>​ > wlctl revinfo
 +vendorid 0x14e4
 +deviceid 0x4357
 +radiorev 0xb2056000
 +chipnum 0xa8d9
 +chiprev 0x1
 +chippackage 0x8
 +corerev 0x17
 +boardid 0xa8d8
 +boardvendor 0x14e4
 +boardrev P200
 +driverrev 0x5647b00
 +ucoderev 0x2930000
 +bus 0x1
 +phytype 0x4
 +phyrev 0x6
 +anarev 0x0
 + > wlctl srdump
 +
 +  srom[000]: ​ 0x2801 ​ 0x0000 ​ 0x04da ​ 0x14e4 ​ 0x0078 ​ 0xedbe ​ 0x0000 ​ 0x2bc4  ​
 +  srom[008]: ​ 0x2a64 ​ 0x2964 ​ 0x2c64 ​ 0x3ce7 ​ 0x46ff ​ 0x47ff ​ 0x0c00 ​ 0x0820  ​
 +  srom[016]: ​ 0x0030 ​ 0x1002 ​ 0x9f28 ​ 0x5d44 ​ 0x8080 ​ 0x1d8f ​ 0x0032 ​ 0x0100  ​
 +  srom[024]: ​ 0xdf00 ​ 0x71f5 ​ 0x8400 ​ 0x0083 ​ 0x8500 ​ 0x2010 ​ 0x0001 ​ 0xffff  ​
 +  srom[032]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[040]: ​ 0xffff ​ 0xffff ​ 0x1008 ​ 0x0005 ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[048]: ​ 0x4357 ​ 0x8000 ​ 0x0002 ​ 0x0000 ​ 0x1f30 ​ 0x1800 ​ 0x0000 ​ 0x0000  ​
 +  srom[056]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[064]: ​ 0x5372 ​ 0x1200 ​ 0x0200 ​ 0x0000 ​ 0x1000 ​ 0x0000 ​ 0x0000 ​ 0x0000  ​
 +  srom[072]: ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x88ff ​ 0xffff ​ 0xffff ​ 0x0303 ​ 0x0202  ​
 +  srom[080]: ​ 0xffff ​ 0x0033 ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0x0325  ​
 +  srom[088]: ​ 0xffff ​ 0x7800 ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[096]: ​ 0x204e ​ 0xff11 ​ 0x1567 ​ 0xfb24 ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[104]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[112]: ​ 0x204e ​ 0xff03 ​ 0x154c ​ 0xfb27 ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[120]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[128]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[136]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[144]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[152]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[160]: ​ 0x0000 ​ 0x5555 ​ 0x5555 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000  ​
 +  srom[168]: ​ 0x0000 ​ 0x5555 ​ 0x7555 ​ 0x5555 ​ 0x7555 ​ 0x5555 ​ 0x7555 ​ 0x5555  ​
 +  srom[176]: ​ 0x7555 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000  ​
 +  srom[184]: ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000  ​
 +  srom[192]: ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0000  ​
 +  srom[200]: ​ 0x0000 ​ 0x0000 ​ 0x0000 ​ 0x0002 ​ 0x0000 ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[208]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff ​ 0xffff  ​
 +  srom[216]: ​ 0xffff ​ 0xffff ​ 0xffff ​ 0x0008  ​
 + > wlctl nvram_dump
 +sromrev=8
 +boardrev=0x1200
 +boardflags=0x200
 +boardflags2=0x1000
 +boardtype=0x4da
 +boardnum=0
 +regrev=0
 +ledbh1=136
 +pa0b0=0xff11
 +pa0b1=0x1567
 +pa0b2=0xfb24
 +pa0itssit=32
 +pa0maxpwr=78
 +opo=85
 +aa2g=3
 +aa5g=3
 +ag0=2
 +ag1=2
 +ag2=255
 +ag3=255
 +pa1b0=0xffff
 +pa1b1=0xffff
 +pa1b2=0xffff
 +pa1lob0=0xffff
 +pa1lob1=0xffff
 +pa1lob2=0xffff
 +pa1hib0=0xffff
 +pa1hib1=0xffff
 +pa1hib2=0xffff
 +pa1itssit=255
 +pa1maxpwr=255
 +pa1lomaxpwr=255
 +pa1himaxpwr=255
 +bxa2g=3
 +rssisav2g=7
 +rssismc2g=15
 +rssismf2g=15
 +bxa5g=3
 +rssisav5g=7
 +rssismc5g=15
 +rssismf5g=15
 +tri2g=255
 +tri5g=255
 +tri5gl=255
 +tri5gh=255
 +rxpo2g=-1
 +rxpo5g=-1
 +txchain=3
 +rxchain=3
 +antswitch=0
 +tssipos2g=1
 +extpagain2g=2
 +pdetrange2g=4
 +triso2g=3
 +antswctl2g=0
 +tssipos5g=1
 +extpagain5g=3
 +pdetrange5g=31
 +triso5g=7
 +antswctl5g=31
 +ccode=
 +macaddr=f8:​8e:​85:​08:​dd:​cb
 +tempthresh=120
 +tempoffset=0
 +rawtempsense=0x1ff
 +measpower=0x7f
 +tempsense_slope=0xff
 +tempcorrx=0x3f
 +tempsense_option=0x3
 +freqoffset_corr=0xf
 +iqcal_swp_dis=0x1
 +hw_iqcal_en=0x1
 +elna2g=255
 +elna5g=255
 +phycal_tempdelta=255
 +temps_period=15
 +temps_hysteresis=15
 +measpower1=0x7f
 +measpower2=0x7f
 +cck2gpo=0
 +ofdm2gpo=1431655765
 +ofdm5gpo=0
 +ofdm5glpo=0
 +ofdm5ghpo=0
 +mcs2gpo0=21845
 +mcs2gpo1=30037
 +mcs2gpo2=21845
 +mcs2gpo3=30037
 +mcs2gpo4=21845
 +mcs2gpo5=30037
 +mcs2gpo6=21845
 +mcs2gpo7=30037
 +mcs5gpo0=0
 +mcs5gpo1=0
 +mcs5gpo2=0
 +mcs5gpo3=0
 +mcs5gpo4=0
 +mcs5gpo5=0
 +mcs5gpo6=0
 +mcs5gpo7=0
 +mcs5glpo0=0
 +mcs5glpo1=0
 +mcs5glpo2=0
 +mcs5glpo3=0
 +mcs5glpo4=0
 +mcs5glpo5=0
 +mcs5glpo6=0
 +mcs5glpo7=0
 +mcs5ghpo0=0
 +mcs5ghpo1=0
 +mcs5ghpo2=0
 +mcs5ghpo3=0
 +mcs5ghpo4=0
 +mcs5ghpo5=0
 +mcs5ghpo6=0
 +mcs5ghpo7=0
 +cddpo=0
 +stbcpo=0
 +bw40po=2
 +bwduppo=0
 +pcieingress_war=15
 +rxgainerr2ga0=63
 +rxgainerr2ga1=31
 +rxgainerr2ga2=31
 +rxgainerr5gla0=63
 +rxgainerr5gla1=31
 +rxgainerr5gla2=31
 +rxgainerr5gma0=63
 +rxgainerr5gma1=31
 +rxgainerr5gma2=31
 +rxgainerr5gha0=63
 +rxgainerr5gha1=31
 +rxgainerr5gha2=31
 +rxgainerr5gua0=63
 +rxgainerr5gua1=31
 +rxgainerr5gua2=31
 +noiselvl2ga0=31
 +noiselvl2ga1=31
 +noiselvl2ga2=31
 +noiselvl5gla0=31
 +noiselvl5gla1=31
 +noiselvl5gla2=31
 +noiselvl5gma0=31
 +noiselvl5gma1=31
 +noiselvl5gma2=31
 +noiselvl5gha0=31
 +noiselvl5gha1=31
 +noiselvl5gha2=31
 +noiselvl5gua0=31
 +noiselvl5gua1=31
 +noiselvl5gua2=31
 +maxp2ga0=78
 +itt2ga0=32
 +itt5ga0=255
 +pa2gw0a0=0xff11
 +pa2gw1a0=0x1567
 +pa2gw2a0=0xfb24
 +maxp5ga0=255
 +maxp5gha0=255
 +maxp5gla0=255
 +pa5gw0a0=0xffff
 +pa5gw1a0=0xffff
 +pa5gw2a0=0xffff
 +pa5glw0a0=0xffff
 +pa5glw1a0=0xffff
 +pa5glw2a0=0xffff
 +pa5ghw0a0=0xffff
 +pa5ghw1a0=0xffff
 +pa5ghw2a0=0xffff
 +maxp2ga1=78
 +itt2ga1=32
 +itt5ga1=255
 +pa2gw0a1=0xff03
 +pa2gw1a1=0x154c
 +pa2gw2a1=0xfb27
 +maxp5ga1=255
 +maxp5gha1=255
 +maxp5gla1=255
 +pa5gw0a1=0xffff
 +pa5gw1a1=0xffff
 +pa5gw2a1=0xffff
 +pa5glw0a1=0xffff
 +pa5glw1a1=0xffff
 +pa5glw2a1=0xffff
 +pa5ghw0a1=0xffff
 +pa5ghw1a1=0xffff
 +pa5ghw2a1=0xffff
 +maxp2ga2=255
 +itt2ga2=255
 +itt5ga2=255
 +pa2gw0a2=0xffff
 +pa2gw1a2=0xffff
 +pa2gw2a2=0xffff
 +maxp5ga2=255
 +maxp5gha2=255
 +maxp5gla2=255
 +pa5gw0a2=0xffff
 +pa5gw1a2=0xffff
 +pa5gw2a2=0xffff
 +pa5glw0a2=0xffff
 +pa5glw1a2=0xffff
 +pa5glw2a2=0xffff
 +pa5ghw0a2=0xffff
 +pa5ghw1a2=0xffff
 +pa5ghw2a2=0xffff
 +maxp2ga3=255
 +itt2ga3=255
 +itt5ga3=255
 +pa2gw0a3=0xffff
 +pa2gw1a3=0xffff
 +pa2gw2a3=0xffff
 +maxp5ga3=255
 +maxp5gha3=255
 +maxp5gla3=255
 +pa5gw0a3=0xffff
 +pa5gw1a3=0xffff
 +pa5gw2a3=0xffff
 +pa5glw0a3=0xffff
 +pa5glw1a3=0xffff
 +pa5glw2a3=0xffff
 +pa5ghw0a3=0xffff
 +pa5ghw1a3=0xffff
 +pa5ghw2a3=0xffff
 +devid=0x4357
 +
 + ></​nowiki>​
 +</​WRAP>​\\
 +
 +
 +==== JTAG ====
 +-> [[doc:​hardware:​port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +N/A
 +
 +==== Serial ====
 +-> [[doc:​hardware:​port.serial]] general information about the serial port, serial port cable, etc.
 +
 +How to connect to the Serial Port of this specific device:
 +
 +{{media:​comtrend:​ar-5387un_uart.jpg?​400x200|}}
 +
 +^  o  ^  o  ^  o  ^  o  ^ 
 +|  GND   ​| ​ TX  |  RX  |  Vcc  |
 +
 +Only connect GND, TX and RX
 +
 +===== GPIOs =====
 +==== LEDs ====
 +Read: [[doc:​uci:​system#​leds|System configuration:​ Leds]] to configure the leds
 +^ Label ^ Colour ​                    ^ Active ​  ^ GPIO Pin ^
 +| Internet | <color red>​red</​color> ​ | High     | 1     |
 +| :::   | <color green>​green</​color>​ | High     | 7     ​| ​
 +| Power | <color red>​red</​color> ​    | High     | 4     |
 +| :::   | <color green>​green</​color>​ | High     | 8     |
 +| DSL   | <color green>​green</​color>​ | Low      | 11    |
 +| LAN1  | <color green>​green</​color>​ | Low    | 25 (PINMUX_EPHY0_ACT_LED) |
 +| LAN2  | <color green>​green</​color>​ | Low    | 26 (PINMUX_EPHY1_ACT_LED) |
 +| LAN3  | <color green>​green</​color>​ | Low    | 27 (PINMUX_EPHY2_ACT_LED) |
 +| LAN4  | <color green>​green</​color>​ | Low    | 28 (PINMUX_EPHY3_ACT_LED) |
 +
 +**LAN1 to LAN4** leds are multiplexed,​ this means they are hardware controlled LEDs. We can still control these leds via userspace if we undo the pinmux by writting some particular memory registers. We can access these registers with devmem at memory address ''​0x1000009C''​
 +<​code>​root@OpenWrt:/#​ devmem 0x1000009C 64
 +0x0154000000000000</​code>​
 +
 +Every enabled bit of this register enables/​disables a LAN led.
 +
 +{{:​media:​doc:​hardware:​bcm6328-lan-led_pinmux-bits.png?​nolink|}}
 +
 +
 +The bit 56 enables the LAN4 hardware controlled LED, bit 54 enables LAN3, and so on.
 +^ memory address = 0x1000009C, length = 64 bits ^^^^
 +^ bit ^ description ^ GPIO Pin ^ Label ^ 
 +| 50 | PINMUX_EPHY0_ACT_LED ​  | 25 | LAN1  | 
 +| 52 | PINMUX_EPHY1_ACT_LED ​  | 26 | LAN2  |
 +| 54 | PINMUX_EPHY2_ACT_LED ​  | 27 | LAN3  |
 +| 56 | PINMUX_EPHY3_ACT_LED ​  | 28 | LAN4  |
 +
 +If we want to disable the hardware LED control on LAN1, then we should set the bit 50 to 0, in other words we must write the value ''​0x150000000000000''​ to the memory location ''​0x1000009C''​
 +<​code>​root@OpenWrt:/#​ devmem 0x1000009C 64 0x150000000000000</​code>​
 +Or for example for disabling hardware control on all LAN leds
 +<​code>​root@OpenWrt:/#​ devmem 0x1000009C 64 0x000000000000000</​code>​
 +This way we can control these GPIOs via ''/​sys/​class/​gpio/''​ interface, with scripts or any utility for this purpose. It also allows to use these GPIOs with some some drivers with GPIO stuff involved.
 +==== Buttons ====
 +-> [[doc:​howto:​hardware.button]] on howto use and configure the hardware button(s).
 +^ Event   ^ Active ​  ^ GPIO Pin   ^
 +| reset   | Low      | 23    |
 +
 +==== Other ====
 +^ where                ^ PCB marking ^ GPIO Pin ^
 +| near unsoldered LED8 | R107        | 9      |
 +| :::                  | R109        | 10     |
 +| near reset button ​   | R79         | 12     |
 +| :::                  | R158        | 24     |
 +| near //​Internet//​ LED (LED10) | R10    | 22     |
 +===== Bootlogs =====
 +==== OEM Bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​CFE version 1.0.37-110.11-2 for BCM96328 (32bit,​SP,​BE)
 +Build Date: 2011-04-29 11:30:31 (lain@SW1-BCM-04)
 +Copyright (C) 2000-2009 Broadcom Corporation.
 +
 +HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
 +Total Flash size: 16384K with 4096 sectors
 +Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 67108864 bytes (64MB)
 +Boot Address: 0xb8000000
 +
 +Board IP address ​                 : 192.168.1.1:​ffffff00  ​
 +Host IP address ​                  : 192.168.1.100  ​
 +Gateway IP address ​               :   
 +Run from flash/host (f/h)         : f  ​
 +Default host run file name        : vmlinux  ​
 +Default host flash file name      : bcm963xx_fs_kernel  ​
 +Boot delay (0-9 seconds) ​         : 1  ​
 +Boot image (0=latest, 1=previous) : 0  ​
 +Board Id (0-6)                    : 96328A-1441N1  ​
 +Number of MAC Addresses (1-32) ​   : 32  ​
 +Base MAC Address ​                 : fa:​ba:​da:​fa:​ba:​da  ​
 +PSI Size (1-64) KBytes ​           : 24  ​
 +Enable Backup PSI [0|1]           : 0  ​
 +System Log Size (0-256) KBytes ​   : 0  ​
 +Main Thread Number [0|1]          : 0  ​
 +Serial Number ​                    : ​  
 +Default PSK key                   : ​  
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 0
 +Booting from latest image (0xb8010000) ...
 +Code Address: 0x80010000, Entry Address: 0x80014230
 +Decompression OK!
 +Entry at 0x80014230
 +Closing network.
 +Disabling Switch ports.
 +Flushing Receive Buffers...
 +0 buffers found.
 +Closing DMA Channels.
 +Starting program at 0x80014230
 +Linux version 2.6.30 (charles@SW1-BCM-04) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Wed May 4 19:58:12 CST 2011
 +HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
 +96328A-1441N1 prom init
 +CPU revision is: 0002a075 (Broadcom4350)
 +Determined physical RAM map:
 + ​memory:​ 03f00000 @ 00000000 (usable)
 +Zone PFN ranges:
 +  DMA      0x00000000 -> 0x00001000
 +  Normal ​  ​0x00001000 -> 0x00003f00
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0: 0x00000000 -> 0x00003f00
 +On node 0 totalpages: 16128
 +free_area_init_node:​ node 0, pgdat 8030ea80, node_mem_map 81000000
 +  DMA zone: 32 pages used for memmap
 +  DMA zone: 0 pages reserved
 +  DMA zone: 4064 pages, LIFO batch:0
 +  Normal zone: 94 pages used for memmap
 +  Normal zone: 11938 pages, LIFO batch:1
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16002
 +Kernel command line: root=31:0 ro noinitrd console=ttyS0,​115200
 +wait instruction:​ enabled
 +Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +RCU-based detection of stalled CPUs is enabled.
 +NR_IRQS:128
 +PID hash table entries: 256 (order: 8, 1024 bytes)
 +console [ttyS0] enabled
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Memory: 60504k/​64512k available (2564k kernel code, 3988k reserved, 509k data, 120k init, 0k highmem)
 +Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
 +Mount-cache hash table entries: 512
 +net_namespace:​ 812 bytes
 +NET: Registered protocol family 16
 +Total Flash size: 16384K with 256 sectors
 +registering PCI controller with io_map_base unset
 +registering PCI controller with io_map_base unset
 +bio: create slab <​bio-0>​ at 0
 +SCSI subsystem initialized
 +usbcore: registered new interface driver usbfs
 +usbcore: registered new interface driver hub
 +usbcore: registered new device driver usb
 +pci 0000:​00:​09.0:​ reg 10 32bit mmio: [0x10002600-0x100026ff]
 +pci 0000:​00:​0a.0:​ reg 10 32bit mmio: [0x10002500-0x100025ff]
 +pci 0000:​01:​00.0:​ PME# supported from D0 D3hot
 +pci 0000:​01:​00.0:​ PME# disabled
 +pci 0000:​02:​00.0:​ reg 10 64bit mmio: [0x000000-0x003fff]
 +pci 0000:​02:​00.0:​ supports D1 D2
 +pci 0000:​01:​00.0:​ PCI bridge, secondary bus 0000:02
 +pci 0000:​01:​00.0: ​  IO window: disabled
 +pci 0000:​01:​00.0: ​  MEM window: 0x10f00000-0x10ffffff
 +pci 0000:​01:​00.0: ​  ​PREFETCH window: disabled
 +PCI: Enabling device 0000:​01:​00.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​01:​00.0 to 64
 +BLOG v2.1 Initialized
 +NET: Registered protocol family 8
 +NET: Registered protocol family 20
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP: Hash tables configured (established 2048 bind 2048)
 +TCP reno registered
 +NET: Registered protocol family 1
 +squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +squashfs: version 4.0 with LZMA457 ported by BRCM
 +fuse init (API version 7.11)
 +msgmni has been set to 118
 +io scheduler noop registered (default)
 +pcieport-driver 0000:​01:​00.0:​ device [14e4:6328] has invalid IRQ; check vendor BIOS
 +PCI: Setting latency timer of device 0000:​01:​00.0 to 64
 +Driver '​sd'​ needs updating - please use bus_type methods
 +PPP generic driver version 2.4.2
 +PPP Deflate Compression module registered
 +PPP BSD Compression module registered
 +NET: Registered protocol family 24
 +bcm963xx_mtd driver v1.0
 +File system address: 0xb8010100
 +ehci_hcd: USB 2.0 '​Enhanced'​ Host Controller (EHCI) Driver
 +PCI: Enabling device 0000:​00:​0a.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​00:​0a.0 to 64
 +ehci_hcd 0000:​00:​0a.0:​ EHCI Host Controller
 +ehci_hcd 0000:​00:​0a.0:​ new USB bus registered, assigned bus number 1
 +ehci_hcd 0000:​00:​0a.0:​ Enabling legacy PCI PM
 +ehci_hcd 0000:​00:​0a.0:​ irq 50, io mem 0x10002500
 +ehci_hcd 0000:​00:​0a.0:​ USB f.f started, EHCI 1.00
 +usb usb1: configuration #1 chosen from 1 choice
 +hub 1-0:1.0: USB hub found
 +hub 1-0:1.0: 1 port detected
 +ohci_hcd: USB 1.1 '​Open'​ Host Controller (OHCI) Driver
 +PCI: Enabling device 0000:​00:​09.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​00:​09.0 to 64
 +ohci_hcd 0000:​00:​09.0:​ OHCI Host Controller
 +ohci_hcd 0000:​00:​09.0:​ new USB bus registered, assigned bus number 2
 +ohci_hcd 0000:​00:​09.0:​ irq 49, io mem 0x10002600
 +usb usb2: configuration #1 chosen from 1 choice
 +hub 2-0:1.0: USB hub found
 +hub 2-0:1.0: 1 port detected
 +usbcore: registered new interface driver usblp
 +Initializing USB Mass Storage driver...
 +usbcore: registered new interface driver usb-storage
 +USB Mass Storage support registered.
 +brcmboard: brcm_board_init entry
 +SES: Button Interrupt 0x1 is enabled
 +SES: LED GPIO 0x8009 is enabled
 +Serial: BCM63XX driver $Revision: 3.00 $
 +ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
 +ttyS1 at MMIO 0xb0000120 (irq = 36) is a BCM63XX
 +bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 May  4 2011 19:57:46
 +Broadcom Logger v0.1 May  4 2011 19:57:31
 +Mirror/​redirect action on
 +u32 classifier
 +    input device check on 
 +    Actions configured ​
 +TCP cubic registered
 +Initializing XFRM netlink socket
 +NET: Registered protocol family 17
 +NET: Registered protocol family 15
 +Initializing MCPD Module
 +Ebtables v2.0 registered
 +ebt_time registered
 +ebt_ftos registered
 +ebt_wmm_mark registered
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​
 +All bugs added by David S. Miller <​davem@redhat.com>​
 +VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
 +Freeing unused kernel memory: 120k freed
 +init started: ​ BusyBox v1.00 (2011.05.04-11:​58+0000) multi-call binary
 +
 +
 +BusyBox v1.00 (2011.05.04-11:​58+0000) Built-in shell (msh)
 +Enter '​help'​ for a list of built-in commands.
 +
 +
 +Loading drivers and kernel modules... ​
 +
 +pktflow: module license '​Proprietary'​ taints kernel.
 +Disabling lock debugging due to kernel taint
 +Broadcom Packet Flow Cache  Char Driver v2.1 Mar 18 2010 21:39:51 Registered<​242>​
 +NBUFF v1.0 Initialized
 +Broadcom Packet Flow Cache learning via BLOG enabled.
 +Created Proc FS /​procfs/​fcache
 +Broadcom Packet Flow Cache registered with netdev chain
 +Constructed Broadcom Packet Flow Cache v2.1 Mar 18 2010 21:39:50
 +bcmxtmcfg: bcmxtmcfg_init entry
 +adsl: adsl_init entry
 +Broadcom BCM6328B0 Ethernet Network Device v0.1 May  4 2011 19:57:32
 +dgasp: kerSysRegisterDyingGaspHandler:​ bcmsw registered ​
 +eth0: MAC Address: fa:​ba:​da:​fa:​ba:​da
 +eth1: MAC Address: fa:​ba:​da:​fa:​ba:​da
 +eth2: MAC Address: fa:​ba:​da:​fa:​ba:​da
 +eth3: MAC Address: fa:​ba:​da:​fa:​ba:​da
 +BCM63XX_USB USB Device not present
 +insmod: cannot insert `/​lib/​modules/​2.6.30/​extra/​bcm_usb.ko':​ Success (19): Success
 +PCI: Enabling device 0000:​02:​00.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​02:​00.0 to 64
 +wl:srom strapped
 +wl:(srom strapped) probe/​present=0
 +wl:srom not detected,​using main memory mapped srom info(wombo board)
 +wl:loading /​etc/​wlan/​bcm43225_map.bin
 +wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.100.96.0.cpe4.406.0
 +dgasp: kerSysRegisterDyingGaspHandler:​ wl0 registered ​
 +Broadcom 802.1Q VLAN Interface, v0.1
 +
 +===== Comtrend Release Version A731-406JAZ-C02_R01 =====
 +
 +rut_isApplicationRunning in rut_util.c eid = 24
 +rut_isApplicationRunning in rut_util.c eid = 24
 +Auto-negotiation enabled.
 +Link is down
 +device eth0 entered promiscuous mode
 +ip_tables: (C) 2000-2006 Netfilter Core Team
 +Auto-negotiation enabled.
 +Link is down
 +device eth1 entered promiscuous mode
 +Auto-negotiation enabled.
 +Link is down
 +device eth2 entered promiscuous mode
 +Auto-negotiation enabled.
 +Link is down
 +device eth3 entered promiscuous mode
 +device wl0 entered promiscuous mode
 +br0: port 5(wl0) entering forwarding state
 +BcmAdsl_Initialize=0xC00E2FEC,​ g_pFnNotifyCallback=0xC0106BE4
 +WLmngr Daemon is running
 +optarg=0 shmId=0 ​
 +wlevt_init@107:​ opened loopback socket 4
 +wlevt is ready for new msg...
 +pSdramPHY=0xA3FFFFF8,​ 0xFFFFFFFF 0xFFFFFFFF
 +AdslCoreSharedMemInit:​ shareMemAvailable=492320
 +AdslCoreHwReset: ​ AdslOemDataAddr = 0xA3F691E4
 +dgasp: kerSysRegisterDyingGaspHandler:​ dsl0 registered ​
 +monitor task is initialized pid= 239 
 +backup_psi_number_blk=0 result=24576
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +device wl0 entered promiscuous mode
 +br0: port 5(wl0) entering forwarding state
 +br0: port 5(wl0) entering disabled state
 +There is no Predefined DevicePin in CFE
 +WPS Device PIN = 12345678
 +Setting SSID: "​AR-5387un"​
 +Setting SSID: "​wl0_Guest1"​
 +Setting SSID: "​wl0_Guest2"​
 +Setting SSID: "​wl0_Guest3"​
 +wlctl: Not Permitted
 +wlctl: Unsupported
 +wlctl: Unsupported
 +chanspec 0x2b06 selected ​
 +6 (0x2b06)
 +br0: port 5(wl0) entering forwarding state
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +device wl0 entered promiscuous mode
 +br0: port 5(wl0) entering forwarding state
 +Reaped 759
 +UPnP daemon is ready to run
 +
 +BCM96328 Broadband Router
 +Login:</​nowiki>​
 +</​WRAP>​\\
 +
 +==== OpenWrt ====
 +<WRAP bootlog>
 +<​nowiki>​[ ​   0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Wed Jul 18 13:38:05 CEST 2012
 +[    0.000000] Detected Broadcom 0x6328 CPU revision 10b0
 +[    0.000000] CPU frequency is 320 MHz
 +[    0.000000] 64MB of RAM installed
 +[    0.000000] registering 32 GPIOs
 +[    0.000000] gpiochip_add:​ registered GPIOs 0 to 31 on device: bcm63xx-gpio
 +[    0.000000] board_bcm963xx:​ Boot address 0xb8000000
 +[    0.000000] board_bcm963xx:​ CFE version: 1.0.37-110.11
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
 +[    0.000000] board_bcm963xx:​ board name: 96328A-1441N1
 +[    0.000000] Determined physical RAM map:
 +[    0.000000] ​ memory: 04000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone PFN ranges:
 +[    0.000000] ​  ​Normal ​  ​0x00000000 -> 0x00004000
 +[    0.000000] Movable zone start PFN for each node
 +[    0.000000] Early memory PFN ranges
 +[    0.000000] ​    0: 0x00000000 -> 0x00004000
 +[    0.000000] On node 0 totalpages: 16384
 +[    0.000000] free_area_init_node:​ node 0, pgdat 802a5a60, node_mem_map 81000000
 +[    0.000000] ​  ​Normal zone: 128 pages used for memmap
 +[    0.000000] ​  ​Normal zone: 0 pages reserved
 +[    0.000000] ​  ​Normal zone: 16256 pages, LIFO batch:3
 +[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
 +[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 +[    0.000000] pcpu-alloc: [0] 0 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +[    0.000000] Kernel command line:  root=/​dev/​mtdblock2 rootfstype=squashfs,​jffs2 noinitrd console=ttyS0,​115200
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] Memory: 61864k/​65536k available (2248k kernel code, 3672k reserved, 399k data, 200k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
 +[    0.036000] pid_max: default: 32768 minimum: 301
 +[    0.040000] Mount-cache hash table entries: 512
 +[    0.048000] NET: Registered protocol family 16
 +[    0.276000] registering PCI controller with io_map_base unset
 +[    0.288000] bio: create slab <​bio-0>​ at 0
 +[    0.292000] PCI host bridge to bus 0000:00
 +[    0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
 +[    0.300000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
 +[    0.304000] pci 0000:​00:​00.0:​ [14e4:6328] type 1 class 0x000604
 +[    0.304000] pci 0000:​00:​00.0:​ PME# supported from D0 D3hot
 +[    0.304000] pci 0000:​01:​00.0:​ [14e4:a8d8] type 0 class 0x000280
 +[    0.304000] pci 0000:​01:​00.0:​ reg 10: [mem 0x00000000-0x00003fff 64bit]
 +[    0.304000] pci 0000:​01:​00.0:​ supports D1 D2
 +[    0.304000] pci 0000:​00:​00.0:​ BAR 8: assigned [mem 0x10f00000-0x10ffffff]
 +[    0.308000] pci 0000:​01:​00.0:​ BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
 +[    0.312000] pci 0000:​00:​00.0:​ PCI bridge to [bus 01-01]
 +[    0.316000] pci 0000:​00:​00.0: ​  ​bridge window [mem 0x10f00000-0x10ffffff]
 +[    0.320000] PCI: Enabling device 0000:​00:​00.0 (0000 -> 0002)
 +[    0.324000] Switching to clocksource MIPS
 +[    0.332000] PCI: Enabling device 0000:​01:​00.0 (0000 -> 0002)
 +[    0.340000] bcma: bus0: Found chip with id 0xA8D9, rev 0x01 and package 0x0A
 +[    0.344000] bcma: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
 +[    0.356000] bcma: bus0: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
 +[    0.364000] bcma: bus0: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
 +[    0.372000] bcma: bus0: Found rev 6 PMU (capabilities 0x108C2606)
 +[    0.372000] bcma: bus0: PMU resource config unknown or not needed for device 0xA8D9
 +[    0.372000] bcma: bus0: Workarounds unknown or not needed for device 0xA8D9
 +[    0.408000] bcma: bus0: SPROM offset 0x800
 +[    0.448000] bcma: Reading SPROM failed. Trying fallback SPROM...
 +[    0.448000] bcma: bus0: Using SPROM revision 8 provided by platform.
 +[    0.448000] bcma: bus0: Bus registered
 +[    0.452000] NET: Registered protocol family 2
 +[    0.456000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.464000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +[    0.472000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.480000] TCP: Hash tables configured (established 2048 bind 2048)
 +[    0.484000] TCP reno registered
 +[    0.488000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.492000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.500000] NET: Registered protocol family 1
 +[    0.504000] PCI: CLS 0 bytes, default 16
 +[    0.508000] audit: initializing netlink socket (disabled)
 +[    0.512000] type=2000 audit(0.512:​1):​ initialized
 +[    0.520000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +[    0.528000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.536000] msgmni has been set to 120
 +[    0.540000] io scheduler noop registered
 +[    0.544000] io scheduler deadline registered (default)
 +[    0.552000] bcm63xx_uart.0:​ ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
 +[    0.560000] console [ttyS0] enabled, bootconsole disabled
 +[    0.576000] m25p80 spi0.0: found mx25l12805d,​ expected m25p80
 +[    0.584000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
 +[    0.588000] bcm63xxpart:​ CFE boot tag found with version 6 and board type 96328A-1441N1
 +[    0.596000] bcm63xxpart:​ Partition 0 is CFE offset 0 and length 10000
 +[    0.604000] bcm63xxpart:​ Partition 1 is kernel offset 10100 and length eff00
 +[    0.612000] bcm63xxpart:​ Partition 2 is rootfs offset 100000 and length ef0000
 +[    0.620000] bcm63xxpart:​ Partition 3 is nvram offset ff0000 and length 10000
 +[    0.628000] bcm63xxpart:​ Partition 4 is linux offset 10000 and length fe0000
 +[    0.632000] bcm63xxpart:​ Spare partition is offset 2e0004 and length d0fffc
 +[    0.640000] 5 bcm63xxpart partitions found on MTD device spi0.0
 +[    0.648000] Creating 5 MTD partitions on "​spi0.0":​
 +[    0.652000] 0x000000000000-0x000000010000 : "​CFE"​
 +[    0.660000] 0x000000010100-0x000000100000 : "​kernel"​
 +[    0.664000] mtd: partition "​kernel"​ must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    0.680000] 0x000000100000-0x000000ff0000 : "​rootfs"​
 +[    0.688000] mtd: partition "​rootfs"​ set to be root filesystem
 +[    0.696000] mtd: partition "​rootfs_data"​ created automatically,​ ofs=2E0000, len=D10000 ​
 +[    0.704000] 0x0000002e0000-0x000000ff0000 : "​rootfs_data"​
 +[    0.712000] 0x000000ff0000-0x000001000000 : "​nvram"​
 +[    0.720000] 0x000000010000-0x000000ff0000 : "​linux"​
 +[    0.760000] bcm63xx-wdt bcm63xx-wdt: ​ started, timer margin: 30 sec
 +[    0.768000] TCP cubic registered
 +[    0.772000] NET: Registered protocol family 17
 +[    0.776000] 8021q: 802.1Q VLAN Support v1.8
 +[    0.788000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    0.796000] Freeing unused kernel memory: 200k freed
 +[    3.356000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link UP on Port 4, 100Mbps, full-duplex
 +[    3.412000] roboswitch: Probing device eth0: 
 +[    3.416000] bcm63xx_enet:​ could not find a used port with phy_id 0, assuming phy is external
 +[    3.424000] No Robo switch in managed mode found, phy_id = 0xffffffff
 +[    3.432000] roboswitch: Probing device eth1: No such device
 +[    3.436000] roboswitch: Probing device eth2: No such device
 +[    3.444000] roboswitch: Probing device eth3: No such device
 +[    9.456000] JFFS2 notice: (319) jffs2_build_xattr_subsystem:​ complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 7 of xref (0 dead, 2 orphan) found.
 +[   ​12.652000] Compat-wireless backport release: compat-wireless-2012-07-13
 +[   ​12.660000] Backport based on wireless-testing.git master-2012-07-16
 +[   ​12.664000] compat.git: wireless-testing.git
 +[   ​12.728000] cfg80211: Calling CRDA to update world regulatory domain
 +[   ​12.732000] cfg80211: World regulatory domain updated:
 +[   ​12.740000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp)
 +[   ​12.748000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​12.756000] cfg80211: ​  ​(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   ​12.764000] cfg80211: ​  ​(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   ​12.772000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​12.780000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​13.184000] NET: Registered protocol family 10
 +[   ​13.408000] SCSI subsystem initialized
 +[   ​13.464000] There is already a switch registered on the device '​eth0'​
 +[   ​13.468000] roboswitch: Probing device eth1: No such device
 +[   ​13.476000] roboswitch: Probing device eth2: No such device
 +[   ​13.480000] roboswitch: Probing device eth3: No such device
 +[   ​13.744000] usbcore: registered new interface driver usbfs
 +[   ​13.748000] usbcore: registered new interface driver hub
 +[   ​13.756000] usbcore: registered new device driver usb
 +[   ​14.404000] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
 +[   ​14.408000] bcma: bus0: Switched to core: 0x812
 +[   ​14.412000] Broadcom 43xx driver loaded [ Features: PNL ]
 +[   ​14.612000] Button Hotplug driver version 0.4.1
 +[   ​14.828000] ieee80211 phy0: Selected rate control algorithm '​minstrel_ht'​
 +[   ​14.832000] Registered led device: b43-phy0::​tx
 +[   ​14.832000] Registered led device: b43-phy0::​rx
 +[   ​14.832000] Registered led device: b43-phy0::​radio
 +[   ​15.468000] PPP generic driver version 2.4.2
 +[   ​15.688000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​15.908000] NET: Registered protocol family 24
 +[   ​16.052000] ehci_hcd: USB 2.0 '​Enhanced'​ Host Controller (EHCI) Driver
 +[   ​16.096000] nf_conntrack version 0.5.0 (969 buckets, 3876 max)
 +[   ​16.544000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​16.896000] ohci_hcd: USB 1.1 '​Open'​ Host Controller (OHCI) Driver
 +[   ​16.956000] uhci_hcd: USB Universal Host Controller Interface driver
 +[   ​17.044000] Initializing USB Mass Storage driver...
 +[   ​17.048000] usbcore: registered new interface driver usb-storage
 +[   ​17.056000] USB Mass Storage support registered.
 +[   ​21.004000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link UP on Port 4, 100Mbps, full-duplex
 +[   ​21.012000] device eth0 entered promiscuous mode
 +[   ​21.020000] br-lan: port 1(eth0) entered forwarding state
 +[   ​21.024000] br-lan: port 1(eth0) entered forwarding state
 +[   ​23.028000] br-lan: port 1(eth0) entered forwarding state
 +[   ​23.260000] cfg80211: Calling CRDA for country: ES
 +[   ​23.264000] cfg80211: Regulatory domain changed to country: ES
 +[   ​23.272000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp)
 +[   ​23.280000] cfg80211: ​  ​(2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
 +[   ​23.288000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
 +[   ​23.296000] cfg80211: ​  ​(5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
 +[   ​23.304000] cfg80211: ​  ​(5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
 +[   ​24.760000] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
 +[   ​24.864000] ADDRCONF(NETDEV_UP):​ wlan0: link is not ready
 +[   ​27.408000] wlan0: authenticate with 11:​22:​33:​44:​55:​66
 +[   ​27.448000] wlan0: send auth to 11:​22:​33:​44:​55:​66 (try 1/3)
 +[   ​27.456000] wlan0: authenticated
 +[   ​27.460000] b43 bcma0:0: wlan0: disabling HT as WMM/QoS is not supported
 +[   ​27.472000] wlan0: associate with 11:​22:​33:​44:​55:​66 (try 1/3)
 +[   ​27.480000] wlan0: RX AssocResp from 11:​22:​33:​44:​55:​66 (capab=0x411 status=0 aid=2)
 +[   ​27.488000] wlan0: associated
 +[   ​27.492000] ADDRCONF(NETDEV_CHANGE):​ wlan0: link becomes ready
 +[   ​38.016000] wlan0: no IPv6 routers present
 +[  150.012000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link DOWN on Port 4
 +[  265.016000] bcm63xx_enetsw bcm63xx_enetsw.0:​ link UP on Port 2, 100Mbps, full-duplex</​nowiki>​
 +</​WRAP>​\\
 +
 +===== Tags =====
 +{{tag>​bcm63xx bcm6328 16flash 64ram}}