User Tools

Site Tools


toh:comtrend:ct5813

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
toh:comtrend:ct5813 [2013/01/15 16:12]
toh:comtrend:ct5813 [2017/08/24 14:14] (current)
danitool Overclocking
Line 1: Line 1:
 +====== Comtrend WAP-5813n ======
  
 +===== Supported Versions =====
 +---- datatable ----
 +cols    : Brand, Model, Versions, Supported Current Rel, OEM device homepage URL_url, Forum Topic URL_url, Device Techdata_pageid
 +headers : Brand, Model, Version, Current Release, OEM Info, Forum Topic, Technical Data
 +align   : c,​c,​c,​c,​c,​c,​c
 +filter ​ : Model=WAP-5813n
 +----
 +
 +===== Installation =====
 +
 +Download the Firmware (SMP is better for Dual Core CPUs) https://​downloads.lede-project.org/​releases/​17.01.1/​targets/​brcm63xx/​smp/​lede-17.01.1-brcm63xx-smp-WAP-5813n-squashfs-cfe.bin
 +
 +
 +==== Flashing ANY Firmware ====
 +You must set your TCP/IP v4 protocol to:
 +  - IP: 192.168.1.2
 +  - Netmask: 255.255.255.0
 +  - Gateway: 192.168.1.1
 +  - DNS: (optional, can be blank).
 +Then:
 +  - Power off the router.
 +  - Press reset button near the antenna.
 +  - Keep it pressed while powering up during ~20+ seconds.
 +  - Acces to http://​192.168.1.1 and upload binary file.
 +  - Wait until router reboots.
 +
 +
 +===== Hardware =====
 +==== Info ====
 +| **[[wp>​Instruction set|Architecture]]:​** ​  | [[wp>​MIPS architecture|MIPS]] ​               |
 +| **Vendor:​** ​                               | [[wp>​Broadcom]] ​                             |
 +| **[[doc:​techref:​Bootloader]]:​** ​           | [[doc:​techref:​bootloader:​CFE]] ​              |
 +| **Board ID:**                              | 96369R-1231N ​                                |
 +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​  | Broadcom BCM6369 ​                            |
 +| **[[doc:​hardware:​cpu|CPU]]/​Speed** ​        | BMIPS4350 v3.1 / 400 MHz                     |
 +| **Flash-Chip:​** ​                           | MX29LV640EBTI-70G ​                           |
 +| **Flash size** ​                            | 8 MiB                                        |
 +| **RAM** ​                                   | 64 MiB / DDR-400 ​                            |
 +| **Wireless** ​                              | BCM4322 (14e4:432c) 802.11b/g/n (mini-pci) ​  |
 +| **Antenna** ​                               | 2x                                           |
 +| **Ethernet:​** ​       | Broadcom ​ {{:​media:​datasheets:​bcm53115_datasheet.pdf|BCM53115}} w/ vlan support [[doc:​uci:​network#​swconfig]] |
 +| **USB** ​                                   | [[#​usb.mod|usb mod]]                   |
 +| **Power adapter** ​                         | 12V DC 1A / ELEMENTECH Horizon-794me ​  |
 +| **[[doc:​hardware:​port.serial|Serial]]:​** ​  | [[#​Serial|Yes]] ​                       |
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​      | [[#​JTAG|?​]] ​                           |
 +
 +==== Photos ====
 +{{media:​comtrend:​ct-5813:​ct-5813.jpg?​0x300}}
 +{{media:​comtrend:​ct-5813:​ct-5813_board_up.jpg?​0x300}}
 +{{media:​comtrend:​ct-5813:​ct-5813_board_down.jpg?​0x300}}
 +
 +==== JTAG ====
 +-> [[doc:​hardware:​port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +N/A
 +
 +==== Serial ====
 +-> [[doc:​hardware:​port.serial]] general information about the serial port, serial port cable, etc.
 +
 +How to connect to the Serial Port of this specific device:\\
 +{{media:​comtrend:​ct-5813:​ct-5813_serial.jpg?​400}}
 +
 +==== Switch ====
 +This board unlike others BCM6368 boards uses a dedicated BCM53115 Gigabit switch (other boards use the internal fast ethernet switch at the SoC). Here a typical/​right configuration:​\\
 +{{media:​comtrend:​wap5813n_switch_conf.png?​400}}
 +
 +==== GPIO ====
 +
 +=== LEDs ===
 +Read: [[doc:​uci:​system#​leds|System configuration:​ Leds]] to configure the leds
 +^ Pin   ^ Event           ^ Active ​  ^
 +| 5     | inet (red)      | High     |
 +| 14    | aux             | Low      |
 +| 22    | power (green) ​  | High     |
 +| 23    | wps             | Low      |
 +| 24    | power (red)     | High     |
 +| 31    | inet (green) ​   | High     |
 +
 +=== Buttons ===
 +-> [[doc:​howto:​hardware.button]] on howto use and configure the hardware button(s).
 +^ Pin   ^ Event   ^ Active ​  ^
 +| 32    | Wifi    | Low      |
 +| 34    | Reset   | Low      |
 +| 35    | WPS     | Low      |
 +
 +===== Bootlogs =====
 +==== OEM Bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​CFE version 1.0.37-102.1-5 for BCM96368 (32bit,​SP,​BE)
 +Build Date: Tue Oct 27 19:02:58 CST 2009 (roger@broadcom2.comtrend.com)
 +Copyright (C) 2000-2008 Broadcom Corporation.
 +
 +Parallel flash device: name AM29DL800B, id 0x22cb, size 8192KB
 +######## BCM53115_is_ready:​487 ####### ID=0x53115
 +######## BCM53115_is_ready:​491 ####### BCM53115 UP !!!!
 +CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz
 +CPU running TP0
 +Total memory: 67108864 bytes (64MB)
 +Boot Address 0xb8000000
 +
 +
 +Board IP address ​                 : 192.168.1.1:​ffffff00  ​
 +Host IP address ​                  : 192.168.1.100  ​
 +Gateway IP address ​               :   
 +Run from flash/host (f/h)         : f  ​
 +Default host run file name        : vmlinux  ​
 +Default host flash file name      : bcm963xx_fs_kernel  ​
 +Boot delay (0-9 seconds) ​         : 1  ​
 +Boot image (0=latest, 1=previous) : 0  ​
 +Board Id (0-10) ​                  : 96369R-1231N  ​
 +Number of MAC Addresses (1-32) ​   : 11  ​
 +Base MAC Address ​                 : 11:​22:​33:​44:​55:​66  ​
 +PSI Size (1-64) KBytes ​           : 24  ​
 +Main Thread Number [0|1]          : 0  ​
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 110
 +Booting from latest image (0xb8010000) ...
 +Code Address: 0x80010000, Entry Address: 0x801db000
 +Decompression OK!
 +Entry at 0x801db000
 +Closing network.
 +Disabling Switch ports.
 +Flushing Receive Buffers...
 +0 buffers found.
 +Closing DMA Channels.
 +Starting program at 0x801db000
 +Linux version 2.6.21.5 (tony@broadcom_eu) (gcc version 4.2.3) #1 Wed Aug 11 13:4
 +8:23 CST 2010
 +Parallel flash device: name AM29DL800B, id 0x22cb, size 8192KB
 +96369R-1231N prom init
 +CPU revision is: 0002a031
 +Determined physical RAM map:
 + ​memory:​ 03f00000 @ 00000000 (usable)
 +On node 0 totalpages: 16128
 +  DMA zone: 32 pages used for memmap
 +  DMA zone: 0 pages reserved
 +  DMA zone: 4064 pages, LIFO batch:0
 +  Normal zone: 94 pages used for memmap
 +  Normal zone: 11938 pages, LIFO batch:1
 +Built 1 zonelists. ​ Total pages: 16002
 +Kernel command line: root=31:0 ro noinitrd console=ttyS0,​115200
 +brcm mips: enabling icache and dcache...
 +Primary instruction cache 64kB, physically tagged, 4-way, linesize 16 bytes.
 +Primary data cache 32kB, 2-way, linesize 16 bytes.
 +Synthesized TLB refill handler (21 instructions).
 +Synthesized TLB load handler fastpath (33 instructions).
 +Synthesized TLB store handler fastpath (33 instructions).
 +Synthesized TLB modify handler fastpath (32 instructions).
 +PID hash table entries: 256 (order: 8, 1024 bytes)
 +Using 200.000 MHz high precision timer.
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Memory: 61820k/​64512k available (1577k kernel code, 2676k reserved, 254k data, 8
 +4k init, 0k highmem)
 +Calibrating delay loop... 398.95 BogoMIPS (lpj=997376)
 +Mount-cache hash table entries: 512
 +NET: Registered protocol family 16
 +Total Flash size: 8192K with 135 sectors
 +File system address: 0xb8010100
 +registering PCI controller with io_map_base unset
 +BLOG v1.0 Initialized
 +NET: Registered protocol family 8
 +NET: Registered protocol family 20
 +NET: Registered protocol family 2
 +Time: MIPS clocksource has been installed.
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP: Hash tables configured (established 2048 bind 2048)
 +TCP reno registered
 +squashfs: version 3.2-r2 (2007/​01/​15) Phillip Lougher
 +squashfs: LZMA suppport for slax.org by jro
 +io scheduler noop registered (default)
 +PPP generic driver version 2.4.2
 +NET: Registered protocol family 24
 +bcm963xx_mtd driver v1.0
 +brcmboard: brcm_board_init entry
 +SES: Button Interrupt 0x1 is enabled
 +SES: LED GPIO 0x8017 is enabled
 +Serial: BCM63XX driver $Revision: 3.00 $
 +ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
 +ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
 +bcmxtmrt: Broadcom BCM6369B2 ATM/PTM Network Device v0.1 Aug 11 2010 13:47:20
 +TCP cubic registered
 +NET: Registered protocol family 1
 +NET: Registered protocol family 17
 +NET: Registered protocol family 15
 +Bridge firewalling registered
 +Ebtables v2.0 registered
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​
 +All bugs added by David S. Miller <​davem@redhat.com>​
 +VFS: Mounted root (squashfs filesystem) readonly.
 +Freeing unused kernel memory: 84k freed
 +init started: ​ BusyBox v1.00 (2010.08.11-05:​49+0000) multi-call binary
 +
 +
 +BusyBox v1.00 (2010.08.11-05:​49+0000) Built-in shell (msh)
 +Enter '​help'​ for a list of built-in commands.
 +
 +
 +Loading drivers and kernel modules... ​
 +
 +pktflow: module license '​Proprietary'​ taints kernel.
 +Broadcom Packet Flow Cache learning via BLOG enabled.
 +Created Proc FS /​procfs/​fcache
 +Constructed Broadcom Packet Flow Cache v0.1 Oct  9 2009 15:28:19
 +Broadcom Packet CMF (Experimental) Char Driver v0.1 Feb 19 2009 23:49:14 Registe
 +red<​232>​
 +Broadcom Packet CMF (Experimental) [6369-B2] v0.1 Feb 19 2009 23:49:14 Loaded
 +bcmxtmcfg: bcmxtmcfg_init entry
 +adsl: adsl_init entry
 +Broadcom BCMPROCFS v1.0 initialized
 +Broadcom BCM6369B2 Ethernet Network Device v0.1 Aug 11 2010 13:47:15
 +######## ethsw_disable_internal_phy:​329 ####### Disable internal PHY ID 1 
 +######## ethsw_disable_internal_phy:​329 ####### Disable internal PHY ID 2 
 +######## ethsw_disable_internal_phy:​329 ####### Disable internal PHY ID 3 
 +######## ethsw_disable_internal_phy:​329 ####### Disable internal PHY ID 4 
 +####​ethsw_init_table:​83 #### port[0]: index=4 phyid= 0x11
 +####​ethsw_init_table:​83 #### port[1]: index=5 phyid= 0x10
 +dgasp: kerSysRegisterDyingGaspHandler:​ bcmsw registered ​
 +######## ethsw_config_learning:​513 ####### jumbo reg=0x0000FFFF
 +######## ethsw_config_learning:​515 ####### jumbo reg=0x00000000
 +######## ethsw_config_learning:​517 ####### jumbo reg=0x000001FF
 +######## ethsw_config_learning:​520 ####### jumbo reg=0x000001FF
 +######## ethsw_config_learning:​524 ####### jumbo size=1518
 +######## ethsw_config_learning:​528 ####### jumbo size=2000
 +Broadcom Packet CMF (Experimental) SWC RESET.
 +Broadcom Packet CMF (Experimental) SWC INITIALIZED.
 +Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Feb 19 2009 23:49
 +:15 Registered
 +Broadcom Packet CMF (Experimental) Forwarder Net Device 1 v0.1 Feb 19 2009 23:49
 +:15 Registered
 +Broadcom Packet CMF (Experimental) ENABLED.
 +######## BCM53115_enable_wan_port:​2120 ####### set BCM53115 WAN_REG = 0x0210 ​
 +######## BCM53115_enable_wan_port:​2181 ####### set BCM53115 DISABLE_LEARN_REG = 
 +0x0000 ​
 +######## BCM53115_fake_netdev_init:​2461 ####### page 0x30 reg 0x62 0xfa50
 +######## BCM53115_fake_netdev_init:​2512 ####### Queue config=0x3
 +eth1: MAC Address: 11:​22:​33:​44:​55:​66
 +eth2: MAC Address: 11:​22:​33:​44:​55:​66
 +eth3: MAC Address: 11:​22:​33:​44:​55:​66
 +eth4: MAC Address: 11:​22:​33:​44:​55:​66
 +eth0: MAC Address: 11:​22:​33:​44:​55:​66
 +PCI: Enabling device 0000:​00:​01.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​00:​01.0 to 64
 +wl0: Broadcom BCM432c 802.11 Wireless Controller 5.10.120.0.cpe4.402.9
 +dgasp: kerSysRegisterDyingGaspHandler:​ wl0 registered ​
 +p8021ag: p8021ag_init entry
 +
 +===== Comtrend Release Version P401-402TLF-C02_R35 =====
 +
 +wl_cnt= 1
 +device eth1 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​62 ####
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth1 
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +device eth2 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​62 ####
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth2 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth1 
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +device eth3 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​62 ####
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth3 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth2 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth1 
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +device eth4 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​62 ####
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth4 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth3 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth2 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth1 
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +WLmngr Daemon is running
 +optarg=0 shmId=0 ​
 +device wl0 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +br0: port 5(wl0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 5(wl0) entering forwarding state
 +BcmAdsl_Initialize=0xC00933C4,​ g_pFnNotifyCallback=0xC00B4834
 +AnnexCParam=0x00000000 AnnexAParam=0x00007987 adsl2=0x00000001 vdslParam=0x007F0
 +07F vdslParam1=0x00000000
 +Clocks for QPROC and AFE are being aligned with step through ... 
 +AFE is aligned, i = 050, PhaseValue = -050, PhaseCntl = 0x3FCE0000
 +QPROC is aligned, i = 051, PhaseValue = -050, PhaseCntl = 0x3FCE3FCD
 +Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x70
 +AFE  phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f
 +QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f
 +pSdramPHY=0xA3FFFFF8,​ 0xAA55AA55 0xAA55AA55
 +AdslCoreSharedMemInit:​ shareMemAvailable=359216
 +AdslCoreHwReset: ​ AdslOemDataAddr = 0xA3F8CB5C
 +AnnexCParam=0x00000000 AnnexAParam=0x00007987 adsl2=0x00000001 vdslParam=0x007F0
 +07F vdslParam1=0x00000000
 +dgasp: kerSysRegisterDyingGaspHandler:​ dsl0 registered ​
 +######## BCM53115_enable_wan_port:​2120 ####### set BCM53115 WAN_REG = 0x0210 ​
 +######## BCM53115_enable_wan_port:​2181 ####### set BCM53115 DISABLE_LEARN_REG = 
 +0x0130 ​
 +eth0.3: add 01:​00:​5e:​00:​00:​01 mcast address to master interface
 +eth0.6: add 01:​00:​5e:​00:​00:​01 mcast address to master interface
 +Scratch pad is not initialized.
 +Register interface ppp0.6 !!
 +wlctl -i wl0 phytype > /var/wl0
 +wlctl -i wl0 revinfo > /var/wl0
 +wlctl -i wl0 bands > /​var/​wl0bands
 +wlctl ver > /var/wlver
 +wlctl -i wl0 cap > /var/wl0cap
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +device wl0 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +br0: port 5(wl0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 5(wl0) entering forwarding state
 +interface wl0.1 does not exist!
 +interface wl0.2 does not exist!
 +interface wl0.3 does not exist!
 +Scratch pad is not initialized.
 +SES: led off
 +br0: port 5(wl0) entering disabled state
 +
 +Comtrend Gigabit 802.11n Router
 +Login: 1234</​nowiki>​
 +</​WRAP>​\\
 +
 +==== Openwrt TEST Bootlog (BCM6368_CPU_ID == 6369) ====
 +<WRAP bootlog>
 +<​nowiki>​[ ​   0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Oct 6 14:55:11 CEST 2012
 +[    0.000000] Detected Broadcom 0x6369 CPU revision b2
 +[    0.000000] CPU frequency is 400 MHz
 +[    0.000000] 64MB of RAM installed
 +[    0.000000] registering 38 GPIOs
 +[    0.000000] gpiochip_add:​ registered GPIOs 0 to 37 on device: bcm63xx-gpio
 +[    0.000000] board_bcm963xx:​ Boot address 0xb8000000
 +[    0.000000] board_bcm963xx:​ CFE version: 1.0.37-102.1
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
 +[    0.000000] board_bcm963xx:​ board name: 96369R-1231N
 +[    0.000000] Determined physical RAM map:
 +[    0.000000] ​ memory: 04000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone PFN ranges:
 +[    0.000000] ​  ​Normal ​  ​0x00000000 -> 0x00004000
 +[    0.000000] Movable zone start PFN for each node
 +[    0.000000] Early memory PFN ranges
 +[    0.000000] ​    0: 0x00000000 -> 0x00004000
 +[    0.000000] On node 0 totalpages: 16384
 +[    0.000000] free_area_init_node:​ node 0, pgdat 802accc0, node_mem_map 81000000
 +[    0.000000] ​  ​Normal zone: 128 pages used for memmap
 +[    0.000000] ​  ​Normal zone: 0 pages reserved
 +[    0.000000] ​  ​Normal zone: 16256 pages, LIFO batch:3
 +[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
 +[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 +[    0.000000] pcpu-alloc: [0] 0 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +[    0.000000] Kernel command line:  root=/​dev/​mtdblock2 rootfstype=squashfs,​jffs2 noinitrd console=ttyS0,​115200
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] Memory: 61692k/​65536k available (2264k kernel code, 3844k reserved, 412k data, 208k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
 +[    0.032000] pid_max: default: 32768 minimum: 301
 +[    0.036000] Mount-cache hash table entries: 512
 +[    0.044000] NET: Registered protocol family 16
 +[    0.052000] registering PCI controller with io_map_base unset
 +[    0.060000] bio: create slab <​bio-0>​ at 0
 +[    0.064000] PCI host bridge to bus 0000:00
 +[    0.068000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
 +[    0.072000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
 +[    0.076000] pci 0000:​00:​01.0:​ [14e4:432c] type 0 class 0x000280
 +[    0.076000] pci 0000:​00:​01.0:​ reg 10: [mem 0x00000000-0x00003fff]
 +[    0.088000] pci 0000:​00:​01.0:​ supports D1 D2
 +[    0.088000] pci 0000:​00:​01.0:​ PME# supported from D0 D3hot D3cold
 +[    0.088000] pci 0000:​00:​01.0:​ BAR 0: assigned [mem 0x30000000-0x30003fff]
 +[    0.092000] Switching to clocksource MIPS
 +[    0.096000] PCI: Enabling device 0000:​00:​01.0 (0000 -> 0002)
 +[    0.104000] b43-pci-bridge 0000:​00:​01.0:​ setting latency timer to 64
 +[    0.128000] ssb: Found chip with id 0x4322, rev 0x01 and package 0x09
 +[    0.136000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x17, vendor 0x4243)
 +[    0.136000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243)
 +[    0.136000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x0B, vendor 0x4243)
 +[    0.136000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243)
 +[    0.136000] ssb: Core 4 found: USB 2.0 Device (cc 0x81A, rev 0x05, vendor 0x4243)
 +[    0.136000] ssb: Core 5 found: ARM Cortex M3 (cc 0x82A, rev 0x00, vendor 0x4243)
 +[    0.136000] ssb: Core 6 found: Internal Memory (cc 0x80E, rev 0x03, vendor 0x4243)
 +[    0.196000] ssb: Sonics Silicon Backplane found on PCI device 0000:​00:​01.0
 +[    0.204000] NET: Registered protocol family 2
 +[    0.212000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.216000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +[    0.224000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.232000] TCP: Hash tables configured (established 2048 bind 2048)
 +[    0.240000] TCP reno registered
 +[    0.240000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.248000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.256000] NET: Registered protocol family 1
 +[    0.260000] PCI: CLS 0 bytes, default 16
 +[    0.260000] audit: initializing netlink socket (disabled)
 +[    0.268000] type=2000 audit(0.268:​1):​ initialized
 +[    0.272000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +[    0.280000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.288000] msgmni has been set to 120
 +[    0.292000] io scheduler noop registered
 +[    0.296000] io scheduler deadline registered (default)
 +[    0.304000] bcm63xx_uart.0:​ ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
 +[    0.312000] console [ttyS0] enabled, bootconsole disabled
 +[    0.324000] bcm63xx-rng bcm63xx-rng:​ registered RNG driver
 +[    0.332000] physmap platform flash device: 08000000 at 18000000
 +[    0.336000] physmap-flash.0:​ Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
 +[    0.348000] physmap-flash.0:​ Found an alias at 0x800000 for the chip at 0x0
 +[    0.348000] physmap-flash.0:​ Found an alias at 0x1000000 for the chip at 0x0
 +[    0.348000] physmap-flash.0:​ Found an alias at 0x1800000 for the chip at 0x0
 +[    0.348000] Amd/Fujitsu Extended Query Table at 0x0040
 +[    0.352000] ​  ​Amd/​Fujitsu Extended Query version 1.1.
 +[    0.360000] number of CFI chips: 1
 +[    0.364000] bcm63xxpart:​ CFE boot tag found with version 6 and board type 96369R-1231N
 +[    0.372000] bcm63xxpart:​ Partition 0 is CFE offset 0 and length 10000
 +[    0.376000] bcm63xxpart:​ Partition 1 is kernel offset 10100 and length eff00
 +[    0.384000] bcm63xxpart:​ Partition 2 is rootfs offset 100000 and length 6f0000
 +[    0.392000] bcm63xxpart:​ Partition 3 is nvram offset 7f0000 and length 10000
 +[    0.400000] bcm63xxpart:​ Partition 4 is linux offset 10000 and length 7e0000
 +[    0.408000] bcm63xxpart:​ Spare partition is offset 2f0004 and length 4ffffc
 +[    0.412000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
 +[    0.420000] Creating 5 MTD partitions on "​physmap-flash.0":​
 +[    0.428000] 0x000000000000-0x000000010000 : "​CFE"​
 +[    0.432000] 0x000000010100-0x000000100000 : "​kernel"​
 +[    0.440000] mtd: partition "​kernel"​ must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    0.452000] 0x000000100000-0x0000007f0000 : "​rootfs"​
 +[    0.460000] mtd: partition "​rootfs"​ set to be root filesystem
 +[    0.468000] mtd: partition "​rootfs_data"​ created automatically,​ ofs=2F0000, len=500000 ​
 +[    0.476000] 0x0000002f0000-0x0000007f0000 : "​rootfs_data"​
 +[    0.480000] 0x0000007f0000-0x000000800000 : "​nvram"​
 +[    0.488000] 0x000000010000-0x0000007f0000 : "​linux"​
 +[    0.532000] bcm63xx-wdt bcm63xx-wdt: ​ started, timer margin: 30 sec
 +[    0.540000] Registered led device: 96369R-1231N:​green:​power
 +[    0.540000] Registered led device: 96369R-1231N:​red:​power
 +[    0.540000] Registered led device: 96369R-1231N:​green:​inet
 +[    0.540000] Registered led device: 96369R-1231N:​red:​inet
 +[    0.540000] Registered led device: 96369R-1231N:​green:​wps
 +[    0.540000] Registered led device: 96369R-1231N:​none:​aux
 +[    0.540000] TCP cubic registered
 +[    0.544000] NET: Registered protocol family 17
 +[    0.548000] 8021q: 802.1Q VLAN Support v1.8
 +[    0.560000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    0.572000] Freeing unused kernel memory: 208k freed
 +[    2.392000] roboswitch: Probing device eth0: 
 +[    2.396000] bcm63xx_enet:​ could not find a used port with phy_id 0, assuming phy is external
 +[    2.408000] Failed to enable switch
 +[    2.412000] roboswitch: Probing device eth1: No such device
 +[    2.416000] roboswitch: Probing device eth2: No such device
 +[    2.424000] roboswitch: Probing device eth3: No such device
 +[    7.864000] JFFS2 notice: (326) jffs2_build_xattr_subsystem:​ complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 0 orphan) found.
 +[    9.944000] NET: Registered protocol family 10
 +[    9.988000] There is already a switch registered on the device '​eth0'​
 +[    9.996000] roboswitch: Probing device eth1: No such device
 +[   ​10.004000] roboswitch: Probing device eth2: No such device
 +[   ​10.008000] roboswitch: Probing device eth3: No such device
 +[   ​11.136000] wl: module license '​unspecified'​ taints kernel.
 +[   ​11.144000] Disabling lock debugging due to kernel taint
 +[   ​11.224000] SSB/BCMA glue driver successfully attached
 +[   ​11.276000] wl0: Broadcom BCM432c 802.11 Wireless Controller 5.10.56.27
 +[   ​11.304000] Button Hotplug driver version 0.4.1
 +[   ​11.336000] PPP generic driver version 2.4.2
 +[   ​11.508000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​11.652000] NET: Registered protocol family 24
 +[   ​11.676000] nf_conntrack version 0.5.0 (967 buckets, 3868 max)
 +[   ​11.940000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​12.140000] input: gpio-keys-polled as /​devices/​platform/​gpio-keys-polled.0/​input/​input0
 +[   ​15.148000] device eth0 entered promiscuous mode
 +[   ​15.164000] br-lan: port 1(eth0) entered forwarding state
 +[   ​15.168000] br-lan: port 1(eth0) entered forwarding state
 +[   ​17.172000] br-lan: port 1(eth0) entered forwarding state</​nowiki>​
 +</​WRAP>​\\
 +
 +===== Hardware Mods =====
 +==== USB Mod ====
 +** Required materials **
 +  * 1 x LM7805 (Voltage regulator, consider a step-down model)
 +  * 1 x Electrolytic capacitor 10-470uF 25V
 +  * 2 x Resistors 4K7 0,25W
 +  * 1 x USB Connector
 +{{media:​comtrend:​ct-5813:​ct-5813_board_up_usb.jpg?​400}}
 +{{media:​comtrend:​ct-5813:​ct-5813_usb_mod_possible.jpg?​250x350}}
 +
 +You need to add a 4K7 resistor on the other side of the board:\\
 +{{media:​comtrend:​ct-5813:​ct-5813_board_down_usb.jpg?​400}}
 +
 +==== Overclocking ====
 +
 +The CPU is configured as default to operate at 400 MHz. With this mod it will be configured to operate at 533 MHz. Solder three 4.7 kohm resistors as shown in the picture.
 +
 +{{:​media:​comtrend:​ct-5813:​wap-5813n-overclocking_533.jpg?​direct&​400|}}
 +===== Tags =====
 +{{tag>​bcm63xx bcm6368 bcm6369 GigabitEthernet 1USB b43 802.11bgn MiniPCI 64RAM 8Flash MIPS MIPS32 trng}}