User Tools

Site Tools


toh:comtrend:ct5813

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
toh:comtrend:ct5813 [2013/01/21 13:50]
toh:comtrend:ct5813 [2016/02/08 02:09] (current)
tmomas ↷ Links adapted because of a move operation
Line 1: Line 1:
 +====== Comtrend WAP-5813n ======
 +Supported since [[https://​dev.openwrt.org/​changeset/​41421|r41421]].
  
 +===== Installation =====
 +==== Flashing ANY Firmware ====
 +You must set your TCP/IP v4 protocol to:
 +  - IP: 192.168.1.2
 +  - Netmask: 255.255.255.0
 +  - Gateway: 192.168.1.1
 +  - DNS: (optional, can be blank).
 +Then:
 +  - Power off the router.
 +  - Press reset button near the antenna.
 +  - Keep it pressed while powering up during ~20+ seconds.
 +  - Acces to http://​192.168.1.1 and upload binary file.
 +  - Wait until router reboots.
 +
 +
 +===== Hardware =====
 +==== Info ====
 +| **[[wp>​Instruction set|Architecture]]:​** ​  | [[wp>​MIPS architecture|MIPS]] ​               |
 +| **Vendor:​** ​                               | [[wp>​Broadcom]] ​                             |
 +| **[[doc:​techref:​Bootloader]]:​** ​           | [[doc:​techref:​bootloader:​CFE]] ​              |
 +| **Board ID:**                              | 96369R-1231N ​                                |
 +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​  | Broadcom BCM6369 ​                            |
 +| **[[doc:​hardware:​cpu|CPU]]/​Speed** ​        | BMIPS4350 v3.1 / 400 MHz                     |
 +| **Flash-Chip:​** ​                           | MX29LV640EBTI-70G ​                           |
 +| **Flash size** ​                            | 8 MiB                                        |
 +| **RAM** ​                                   | 64 MiB / DDR-400 ​                            |
 +| **Wireless** ​                              | BCM4322 (14e4:432c) 802.11b/g/n (mini-pci) ​  |
 +| **Antenna** ​                               | 2x                                           |
 +| **Ethernet:​** ​       | Broadcom ​ {{:​media:​datasheets:​bcm53115_datasheet.pdf|BCM53115}} w/ vlan support [[doc:​uci:​network#​swconfig]] |
 +| **USB** ​                                   | [[#​usb.mod|usb mod]]                   |
 +| **Power adapter** ​                         | 12V DC 1A / ELEMENTECH Horizon-794me ​  |
 +| **[[doc:​hardware:​port.serial|Serial]]:​** ​  | [[#​Serial|Yes]] ​                       |
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​      | [[#​JTAG|?​]] ​                           |
 +
 +==== Photos ====
 +=== Router ===
 +{{media:​comtrend:​ct-5813:​ct-5813.jpg?​400}}
 +
 +=== Board Front ===
 +{{media:​comtrend:​ct-5813:​ct-5813_board_up.jpg?​400}}
 +
 +=== Board Back ===
 +{{media:​comtrend:​ct-5813:​ct-5813_board_down.jpg?​400}}
 +
 +==== JTAG ====
 +-> [[doc:​hardware:​port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +N/A
 +
 +==== Serial ====
 +-> [[doc:​hardware:​port.serial]] general information about the serial port, serial port cable, etc.
 +
 +How to connect to the Serial Port of this specific device:\\
 +{{media:​comtrend:​ct-5813:​ct-5813_serial.jpg?​400}}
 +
 +==== Switch ====
 +This board unlike others BCM6368 boards uses a dedicated BCM53115 Gigabit switch (other boards use the internal fast ethernet switch at the SoC). Here a typical/​right configuration:​\\
 +{{media:​comtrend:​wap5813n_switch_conf.png?​400}}
 +
 +==== GPIO ====
 +
 +=== LEDs ===
 +Read: [[doc:​uci:​system#​leds|System configuration:​ Leds]] to configure the leds
 +^ Pin   ^ Event           ^ Active ​  ^
 +| 5     | inet (red)      | High     |
 +| 14    | aux             | Low      |
 +| 22    | power (green) ​  | High     |
 +| 23    | wps             | Low      |
 +| 24    | power (red)     | High     |
 +| 31    | inet (green) ​   | High     |
 +
 +=== Buttons ===
 +-> [[doc:​howto:​hardware.button]] on howto use and configure the hardware button(s).
 +^ Pin   ^ Event   ^ Active ​  ^
 +| 32    | Wifi    | Low      |
 +| 34    | Reset   | Low      |
 +| 35    | WPS     | Low      |
 +
 +===== Bootlogs =====
 +==== OEM Bootlog ====
 +<WRAP bootlog>
 +<​nowiki>​CFE version 1.0.37-102.1-5 for BCM96368 (32bit,​SP,​BE)
 +Build Date: Tue Oct 27 19:02:58 CST 2009 (roger@broadcom2.comtrend.com)
 +Copyright (C) 2000-2008 Broadcom Corporation.
 +
 +Parallel flash device: name AM29DL800B, id 0x22cb, size 8192KB
 +######## BCM53115_is_ready:​487 ####### ID=0x53115
 +######## BCM53115_is_ready:​491 ####### BCM53115 UP !!!!
 +CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz
 +CPU running TP0
 +Total memory: 67108864 bytes (64MB)
 +Boot Address 0xb8000000
 +
 +
 +Board IP address ​                 : 192.168.1.1:​ffffff00  ​
 +Host IP address ​                  : 192.168.1.100  ​
 +Gateway IP address ​               :   
 +Run from flash/host (f/h)         : f  ​
 +Default host run file name        : vmlinux  ​
 +Default host flash file name      : bcm963xx_fs_kernel  ​
 +Boot delay (0-9 seconds) ​         : 1  ​
 +Boot image (0=latest, 1=previous) : 0  ​
 +Board Id (0-10) ​                  : 96369R-1231N  ​
 +Number of MAC Addresses (1-32) ​   : 11  ​
 +Base MAC Address ​                 : 11:​22:​33:​44:​55:​66  ​
 +PSI Size (1-64) KBytes ​           : 24  ​
 +Main Thread Number [0|1]          : 0  ​
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 110
 +Booting from latest image (0xb8010000) ...
 +Code Address: 0x80010000, Entry Address: 0x801db000
 +Decompression OK!
 +Entry at 0x801db000
 +Closing network.
 +Disabling Switch ports.
 +Flushing Receive Buffers...
 +0 buffers found.
 +Closing DMA Channels.
 +Starting program at 0x801db000
 +Linux version 2.6.21.5 (tony@broadcom_eu) (gcc version 4.2.3) #1 Wed Aug 11 13:4
 +8:23 CST 2010
 +Parallel flash device: name AM29DL800B, id 0x22cb, size 8192KB
 +96369R-1231N prom init
 +CPU revision is: 0002a031
 +Determined physical RAM map:
 + ​memory:​ 03f00000 @ 00000000 (usable)
 +On node 0 totalpages: 16128
 +  DMA zone: 32 pages used for memmap
 +  DMA zone: 0 pages reserved
 +  DMA zone: 4064 pages, LIFO batch:0
 +  Normal zone: 94 pages used for memmap
 +  Normal zone: 11938 pages, LIFO batch:1
 +Built 1 zonelists. ​ Total pages: 16002
 +Kernel command line: root=31:0 ro noinitrd console=ttyS0,​115200
 +brcm mips: enabling icache and dcache...
 +Primary instruction cache 64kB, physically tagged, 4-way, linesize 16 bytes.
 +Primary data cache 32kB, 2-way, linesize 16 bytes.
 +Synthesized TLB refill handler (21 instructions).
 +Synthesized TLB load handler fastpath (33 instructions).
 +Synthesized TLB store handler fastpath (33 instructions).
 +Synthesized TLB modify handler fastpath (32 instructions).
 +PID hash table entries: 256 (order: 8, 1024 bytes)
 +Using 200.000 MHz high precision timer.
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Memory: 61820k/​64512k available (1577k kernel code, 2676k reserved, 254k data, 8
 +4k init, 0k highmem)
 +Calibrating delay loop... 398.95 BogoMIPS (lpj=997376)
 +Mount-cache hash table entries: 512
 +NET: Registered protocol family 16
 +Total Flash size: 8192K with 135 sectors
 +File system address: 0xb8010100
 +registering PCI controller with io_map_base unset
 +BLOG v1.0 Initialized
 +NET: Registered protocol family 8
 +NET: Registered protocol family 20
 +NET: Registered protocol family 2
 +Time: MIPS clocksource has been installed.
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +TCP: Hash tables configured (established 2048 bind 2048)
 +TCP reno registered
 +squashfs: version 3.2-r2 (2007/​01/​15) Phillip Lougher
 +squashfs: LZMA suppport for slax.org by jro
 +io scheduler noop registered (default)
 +PPP generic driver version 2.4.2
 +NET: Registered protocol family 24
 +bcm963xx_mtd driver v1.0
 +brcmboard: brcm_board_init entry
 +SES: Button Interrupt 0x1 is enabled
 +SES: LED GPIO 0x8017 is enabled
 +Serial: BCM63XX driver $Revision: 3.00 $
 +ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
 +ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
 +bcmxtmrt: Broadcom BCM6369B2 ATM/PTM Network Device v0.1 Aug 11 2010 13:47:20
 +TCP cubic registered
 +NET: Registered protocol family 1
 +NET: Registered protocol family 17
 +NET: Registered protocol family 15
 +Bridge firewalling registered
 +Ebtables v2.0 registered
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​
 +All bugs added by David S. Miller <​davem@redhat.com>​
 +VFS: Mounted root (squashfs filesystem) readonly.
 +Freeing unused kernel memory: 84k freed
 +init started: ​ BusyBox v1.00 (2010.08.11-05:​49+0000) multi-call binary
 +
 +
 +BusyBox v1.00 (2010.08.11-05:​49+0000) Built-in shell (msh)
 +Enter '​help'​ for a list of built-in commands.
 +
 +
 +Loading drivers and kernel modules... ​
 +
 +pktflow: module license '​Proprietary'​ taints kernel.
 +Broadcom Packet Flow Cache learning via BLOG enabled.
 +Created Proc FS /​procfs/​fcache
 +Constructed Broadcom Packet Flow Cache v0.1 Oct  9 2009 15:28:19
 +Broadcom Packet CMF (Experimental) Char Driver v0.1 Feb 19 2009 23:49:14 Registe
 +red<​232>​
 +Broadcom Packet CMF (Experimental) [6369-B2] v0.1 Feb 19 2009 23:49:14 Loaded
 +bcmxtmcfg: bcmxtmcfg_init entry
 +adsl: adsl_init entry
 +Broadcom BCMPROCFS v1.0 initialized
 +Broadcom BCM6369B2 Ethernet Network Device v0.1 Aug 11 2010 13:47:15
 +######## ethsw_disable_internal_phy:​329 ####### Disable internal PHY ID 1 
 +######## ethsw_disable_internal_phy:​329 ####### Disable internal PHY ID 2 
 +######## ethsw_disable_internal_phy:​329 ####### Disable internal PHY ID 3 
 +######## ethsw_disable_internal_phy:​329 ####### Disable internal PHY ID 4 
 +####​ethsw_init_table:​83 #### port[0]: index=4 phyid= 0x11
 +####​ethsw_init_table:​83 #### port[1]: index=5 phyid= 0x10
 +dgasp: kerSysRegisterDyingGaspHandler:​ bcmsw registered ​
 +######## ethsw_config_learning:​513 ####### jumbo reg=0x0000FFFF
 +######## ethsw_config_learning:​515 ####### jumbo reg=0x00000000
 +######## ethsw_config_learning:​517 ####### jumbo reg=0x000001FF
 +######## ethsw_config_learning:​520 ####### jumbo reg=0x000001FF
 +######## ethsw_config_learning:​524 ####### jumbo size=1518
 +######## ethsw_config_learning:​528 ####### jumbo size=2000
 +Broadcom Packet CMF (Experimental) SWC RESET.
 +Broadcom Packet CMF (Experimental) SWC INITIALIZED.
 +Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Feb 19 2009 23:49
 +:15 Registered
 +Broadcom Packet CMF (Experimental) Forwarder Net Device 1 v0.1 Feb 19 2009 23:49
 +:15 Registered
 +Broadcom Packet CMF (Experimental) ENABLED.
 +######## BCM53115_enable_wan_port:​2120 ####### set BCM53115 WAN_REG = 0x0210 ​
 +######## BCM53115_enable_wan_port:​2181 ####### set BCM53115 DISABLE_LEARN_REG = 
 +0x0000 ​
 +######## BCM53115_fake_netdev_init:​2461 ####### page 0x30 reg 0x62 0xfa50
 +######## BCM53115_fake_netdev_init:​2512 ####### Queue config=0x3
 +eth1: MAC Address: 11:​22:​33:​44:​55:​66
 +eth2: MAC Address: 11:​22:​33:​44:​55:​66
 +eth3: MAC Address: 11:​22:​33:​44:​55:​66
 +eth4: MAC Address: 11:​22:​33:​44:​55:​66
 +eth0: MAC Address: 11:​22:​33:​44:​55:​66
 +PCI: Enabling device 0000:​00:​01.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:​00:​01.0 to 64
 +wl0: Broadcom BCM432c 802.11 Wireless Controller 5.10.120.0.cpe4.402.9
 +dgasp: kerSysRegisterDyingGaspHandler:​ wl0 registered ​
 +p8021ag: p8021ag_init entry
 +
 +===== Comtrend Release Version P401-402TLF-C02_R35 =====
 +
 +wl_cnt= 1
 +device eth1 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​62 ####
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth1 
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +device eth2 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​62 ####
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth2 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth1 
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +device eth3 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​62 ####
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth3 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth2 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth1 
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +device eth4 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​62 ####
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth4 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth3 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth2 
 +#### Brctl_Port_Base_VLAN_config:​69 #### br0 include ​ eth1 
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +WLmngr Daemon is running
 +optarg=0 shmId=0 ​
 +device wl0 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +br0: port 5(wl0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 5(wl0) entering forwarding state
 +BcmAdsl_Initialize=0xC00933C4,​ g_pFnNotifyCallback=0xC00B4834
 +AnnexCParam=0x00000000 AnnexAParam=0x00007987 adsl2=0x00000001 vdslParam=0x007F0
 +07F vdslParam1=0x00000000
 +Clocks for QPROC and AFE are being aligned with step through ... 
 +AFE is aligned, i = 050, PhaseValue = -050, PhaseCntl = 0x3FCE0000
 +QPROC is aligned, i = 051, PhaseValue = -050, PhaseCntl = 0x3FCE3FCD
 +Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x70
 +AFE  phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f
 +QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f
 +pSdramPHY=0xA3FFFFF8,​ 0xAA55AA55 0xAA55AA55
 +AdslCoreSharedMemInit:​ shareMemAvailable=359216
 +AdslCoreHwReset: ​ AdslOemDataAddr = 0xA3F8CB5C
 +AnnexCParam=0x00000000 AnnexAParam=0x00007987 adsl2=0x00000001 vdslParam=0x007F0
 +07F vdslParam1=0x00000000
 +dgasp: kerSysRegisterDyingGaspHandler:​ dsl0 registered ​
 +######## BCM53115_enable_wan_port:​2120 ####### set BCM53115 WAN_REG = 0x0210 ​
 +######## BCM53115_enable_wan_port:​2181 ####### set BCM53115 DISABLE_LEARN_REG = 
 +0x0130 ​
 +eth0.3: add 01:​00:​5e:​00:​00:​01 mcast address to master interface
 +eth0.6: add 01:​00:​5e:​00:​00:​01 mcast address to master interface
 +Scratch pad is not initialized.
 +Register interface ppp0.6 !!
 +wlctl -i wl0 phytype > /var/wl0
 +wlctl -i wl0 revinfo > /var/wl0
 +wlctl -i wl0 bands > /​var/​wl0bands
 +wlctl ver > /var/wlver
 +wlctl -i wl0 cap > /var/wl0cap
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +device wl0 entered promiscuous mode
 +#### Brctl_Port_Base_VLAN_config:​54 ####
 +#### Brctl_Port_Base_VLAN_config:​78 ####
 +br0: port 5(wl0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 5(wl0) entering forwarding state
 +interface wl0.1 does not exist!
 +interface wl0.2 does not exist!
 +interface wl0.3 does not exist!
 +Scratch pad is not initialized.
 +SES: led off
 +br0: port 5(wl0) entering disabled state
 +
 +Comtrend Gigabit 802.11n Router
 +Login: 1234</​nowiki>​
 +</​WRAP>​\\
 +
 +==== Openwrt TEST Bootlog (BCM6368_CPU_ID == 6369) ====
 +<WRAP bootlog>
 +<​nowiki>​[ ​   0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Oct 6 14:55:11 CEST 2012
 +[    0.000000] Detected Broadcom 0x6369 CPU revision b2
 +[    0.000000] CPU frequency is 400 MHz
 +[    0.000000] 64MB of RAM installed
 +[    0.000000] registering 38 GPIOs
 +[    0.000000] gpiochip_add:​ registered GPIOs 0 to 37 on device: bcm63xx-gpio
 +[    0.000000] board_bcm963xx:​ Boot address 0xb8000000
 +[    0.000000] board_bcm963xx:​ CFE version: 1.0.37-102.1
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350)
 +[    0.000000] board_bcm963xx:​ board name: 96369R-1231N
 +[    0.000000] Determined physical RAM map:
 +[    0.000000] ​ memory: 04000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone PFN ranges:
 +[    0.000000] ​  ​Normal ​  ​0x00000000 -> 0x00004000
 +[    0.000000] Movable zone start PFN for each node
 +[    0.000000] Early memory PFN ranges
 +[    0.000000] ​    0: 0x00000000 -> 0x00004000
 +[    0.000000] On node 0 totalpages: 16384
 +[    0.000000] free_area_init_node:​ node 0, pgdat 802accc0, node_mem_map 81000000
 +[    0.000000] ​  ​Normal zone: 128 pages used for memmap
 +[    0.000000] ​  ​Normal zone: 0 pages reserved
 +[    0.000000] ​  ​Normal zone: 16256 pages, LIFO batch:3
 +[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
 +[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 +[    0.000000] pcpu-alloc: [0] 0 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
 +[    0.000000] Kernel command line:  root=/​dev/​mtdblock2 rootfstype=squashfs,​jffs2 noinitrd console=ttyS0,​115200
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] Memory: 61692k/​65536k available (2264k kernel code, 3844k reserved, 412k data, 208k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648)
 +[    0.032000] pid_max: default: 32768 minimum: 301
 +[    0.036000] Mount-cache hash table entries: 512
 +[    0.044000] NET: Registered protocol family 16
 +[    0.052000] registering PCI controller with io_map_base unset
 +[    0.060000] bio: create slab <​bio-0>​ at 0
 +[    0.064000] PCI host bridge to bus 0000:00
 +[    0.068000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
 +[    0.072000] pci_bus 0000:00: root bus resource [io  0x8000000-0x800ffff]
 +[    0.076000] pci 0000:​00:​01.0:​ [14e4:432c] type 0 class 0x000280
 +[    0.076000] pci 0000:​00:​01.0:​ reg 10: [mem 0x00000000-0x00003fff]
 +[    0.088000] pci 0000:​00:​01.0:​ supports D1 D2
 +[    0.088000] pci 0000:​00:​01.0:​ PME# supported from D0 D3hot D3cold
 +[    0.088000] pci 0000:​00:​01.0:​ BAR 0: assigned [mem 0x30000000-0x30003fff]
 +[    0.092000] Switching to clocksource MIPS
 +[    0.096000] PCI: Enabling device 0000:​00:​01.0 (0000 -> 0002)
 +[    0.104000] b43-pci-bridge 0000:​00:​01.0:​ setting latency timer to 64
 +[    0.128000] ssb: Found chip with id 0x4322, rev 0x01 and package 0x09
 +[    0.136000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x17, vendor 0x4243)
 +[    0.136000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243)
 +[    0.136000] ssb: Core 2 found: PCI-E (cc 0x820, rev 0x0B, vendor 0x4243)
 +[    0.136000] ssb: Core 3 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243)
 +[    0.136000] ssb: Core 4 found: USB 2.0 Device (cc 0x81A, rev 0x05, vendor 0x4243)
 +[    0.136000] ssb: Core 5 found: ARM Cortex M3 (cc 0x82A, rev 0x00, vendor 0x4243)
 +[    0.136000] ssb: Core 6 found: Internal Memory (cc 0x80E, rev 0x03, vendor 0x4243)
 +[    0.196000] ssb: Sonics Silicon Backplane found on PCI device 0000:​00:​01.0
 +[    0.204000] NET: Registered protocol family 2
 +[    0.212000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.216000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
 +[    0.224000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.232000] TCP: Hash tables configured (established 2048 bind 2048)
 +[    0.240000] TCP reno registered
 +[    0.240000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.248000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.256000] NET: Registered protocol family 1
 +[    0.260000] PCI: CLS 0 bytes, default 16
 +[    0.260000] audit: initializing netlink socket (disabled)
 +[    0.268000] type=2000 audit(0.268:​1):​ initialized
 +[    0.272000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +[    0.280000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.288000] msgmni has been set to 120
 +[    0.292000] io scheduler noop registered
 +[    0.296000] io scheduler deadline registered (default)
 +[    0.304000] bcm63xx_uart.0:​ ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart
 +[    0.312000] console [ttyS0] enabled, bootconsole disabled
 +[    0.324000] bcm63xx-rng bcm63xx-rng:​ registered RNG driver
 +[    0.332000] physmap platform flash device: 08000000 at 18000000
 +[    0.336000] physmap-flash.0:​ Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
 +[    0.348000] physmap-flash.0:​ Found an alias at 0x800000 for the chip at 0x0
 +[    0.348000] physmap-flash.0:​ Found an alias at 0x1000000 for the chip at 0x0
 +[    0.348000] physmap-flash.0:​ Found an alias at 0x1800000 for the chip at 0x0
 +[    0.348000] Amd/Fujitsu Extended Query Table at 0x0040
 +[    0.352000] ​  ​Amd/​Fujitsu Extended Query version 1.1.
 +[    0.360000] number of CFI chips: 1
 +[    0.364000] bcm63xxpart:​ CFE boot tag found with version 6 and board type 96369R-1231N
 +[    0.372000] bcm63xxpart:​ Partition 0 is CFE offset 0 and length 10000
 +[    0.376000] bcm63xxpart:​ Partition 1 is kernel offset 10100 and length eff00
 +[    0.384000] bcm63xxpart:​ Partition 2 is rootfs offset 100000 and length 6f0000
 +[    0.392000] bcm63xxpart:​ Partition 3 is nvram offset 7f0000 and length 10000
 +[    0.400000] bcm63xxpart:​ Partition 4 is linux offset 10000 and length 7e0000
 +[    0.408000] bcm63xxpart:​ Spare partition is offset 2f0004 and length 4ffffc
 +[    0.412000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
 +[    0.420000] Creating 5 MTD partitions on "​physmap-flash.0":​
 +[    0.428000] 0x000000000000-0x000000010000 : "​CFE"​
 +[    0.432000] 0x000000010100-0x000000100000 : "​kernel"​
 +[    0.440000] mtd: partition "​kernel"​ must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    0.452000] 0x000000100000-0x0000007f0000 : "​rootfs"​
 +[    0.460000] mtd: partition "​rootfs"​ set to be root filesystem
 +[    0.468000] mtd: partition "​rootfs_data"​ created automatically,​ ofs=2F0000, len=500000 ​
 +[    0.476000] 0x0000002f0000-0x0000007f0000 : "​rootfs_data"​
 +[    0.480000] 0x0000007f0000-0x000000800000 : "​nvram"​
 +[    0.488000] 0x000000010000-0x0000007f0000 : "​linux"​
 +[    0.532000] bcm63xx-wdt bcm63xx-wdt: ​ started, timer margin: 30 sec
 +[    0.540000] Registered led device: 96369R-1231N:​green:​power
 +[    0.540000] Registered led device: 96369R-1231N:​red:​power
 +[    0.540000] Registered led device: 96369R-1231N:​green:​inet
 +[    0.540000] Registered led device: 96369R-1231N:​red:​inet
 +[    0.540000] Registered led device: 96369R-1231N:​green:​wps
 +[    0.540000] Registered led device: 96369R-1231N:​none:​aux
 +[    0.540000] TCP cubic registered
 +[    0.544000] NET: Registered protocol family 17
 +[    0.548000] 8021q: 802.1Q VLAN Support v1.8
 +[    0.560000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    0.572000] Freeing unused kernel memory: 208k freed
 +[    2.392000] roboswitch: Probing device eth0: 
 +[    2.396000] bcm63xx_enet:​ could not find a used port with phy_id 0, assuming phy is external
 +[    2.408000] Failed to enable switch
 +[    2.412000] roboswitch: Probing device eth1: No such device
 +[    2.416000] roboswitch: Probing device eth2: No such device
 +[    2.424000] roboswitch: Probing device eth3: No such device
 +[    7.864000] JFFS2 notice: (326) jffs2_build_xattr_subsystem:​ complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 7 of xref (0 dead, 0 orphan) found.
 +[    9.944000] NET: Registered protocol family 10
 +[    9.988000] There is already a switch registered on the device '​eth0'​
 +[    9.996000] roboswitch: Probing device eth1: No such device
 +[   ​10.004000] roboswitch: Probing device eth2: No such device
 +[   ​10.008000] roboswitch: Probing device eth3: No such device
 +[   ​11.136000] wl: module license '​unspecified'​ taints kernel.
 +[   ​11.144000] Disabling lock debugging due to kernel taint
 +[   ​11.224000] SSB/BCMA glue driver successfully attached
 +[   ​11.276000] wl0: Broadcom BCM432c 802.11 Wireless Controller 5.10.56.27
 +[   ​11.304000] Button Hotplug driver version 0.4.1
 +[   ​11.336000] PPP generic driver version 2.4.2
 +[   ​11.508000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​11.652000] NET: Registered protocol family 24
 +[   ​11.676000] nf_conntrack version 0.5.0 (967 buckets, 3868 max)
 +[   ​11.940000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​12.140000] input: gpio-keys-polled as /​devices/​platform/​gpio-keys-polled.0/​input/​input0
 +[   ​15.148000] device eth0 entered promiscuous mode
 +[   ​15.164000] br-lan: port 1(eth0) entered forwarding state
 +[   ​15.168000] br-lan: port 1(eth0) entered forwarding state
 +[   ​17.172000] br-lan: port 1(eth0) entered forwarding state</​nowiki>​
 +</​WRAP>​\\
 +
 +===== Hardware Mods =====
 +==== USB Mod ====
 +** Required materials **
 +  * 1 x LM7805 (Voltage regulator, consider a step-down model)
 +  * 1 x Electrolytic capacitor 10-470uF 25V
 +  * 2 x Resistors 4K7 0,25W
 +  * 1 x USB Connector
 +{{media:​comtrend:​ct-5813:​ct-5813_board_up_usb.jpg?​400}}
 +{{media:​comtrend:​ct-5813:​ct-5813_usb_mod_possible.jpg?​250x350}}
 +
 +You need to add a 4K7 resistor on the other side of the board:\\
 +{{media:​comtrend:​ct-5813:​ct-5813_board_down_usb.jpg?​400}}
 +
 +===== Tags =====
 +{{tag>​bcm63xx bcm6368 bcm6369 GigabitEthernet 1USB b43 802.11bgn MiniPCI 64RAM 8Flash MIPS MIPS32 trng}}