User Tools

Site Tools


toh:comtrend:ct6373

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
toh:comtrend:ct6373 [2013/04/13 10:23]
toh:comtrend:ct6373 [2016/02/08 02:09] (current)
tmomas ↷ Links adapted because of a move operation
Line 1: Line 1:
 +====== Comtrend CT-6373 ======
 +Supported since [[https://​dev.openwrt.org/​changeset/​32892|R32892]].
  
 +===== Hardware Highlights =====
 +^ SoC             ^ CPU speed   ^ Ram     ^ Flash   ^ Network ​  ^ USB   ^ Serial ​  ^ JTag   ^
 +| Broadcom 6358   | 300MHz ​     | 32MiB   | 8MiB    | 4 x 1     | Yes   | Yes      | Yes?   |
 +
 +[[doc/​howto/​generic.overview]]
 +
 +
 +===== Installation =====
 +  - -> [[doc:​howto:​obtain.firmware]]
 +  - -> [[doc:​howto:​generic.flashing|Install OpenWrt]]
 +
 +==== Flash Layout ====
 +Please check out the article [[doc:​techref:​Flash.Layout]]. It contains an example and a couple of explanations.
 +
 +==== OEM easy installation ====
 +  *Get the firmware [[http://​downloads.openwrt.org/​attitude_adjustment/​12.09/​brcm63xx/​generic/​openwrt-CT6373-squashfs-cfe.bin|openwrt-CT6373-squashfs-cfe.bin]]
 +  *Unplug the power cord
 +  *Press the **<color crimson>//​reset//</​color>​** button, don't release it yet!
 +  *Plug the power cord
 +  *Wait 10 seconds
 +  *Release the //reset// button
 +  *Browse to http://​192.168.1.1
 +  *Upload //​openwrt-CT6373-squashfs-cfe.bin//​ file to router
 +  *Upgrade the image
 +  *Wait for it to reboot
 +  *Telnet to 192.168.1.1 and set a root password, or browse to http://​192.168.1.1 if LuCI is installed.
 +
 +==== OEM installation using the TFTP method ====
 +
 +If you want to upgrade using TFTP you follow these steps (as an alternative to the above install process.
 +
 +==== Upgrading OpenWrt ====
 +->  [[doc:​howto:​generic.sysupgrade]]
 +
 +If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
 +
 +=== LuCI Web Upgrade Process ===
 +
 +  * Browse to http://​192.168.1.1/​cgi-bin/​luci/​mini/​system/​upgrade/​ LuCI Upgrade URL
 +  * Upload image file for sysupgrade to LuCI
 +  * Wait for reboot
 +
 +=== Terminal Upgrade Process ===
 +
 +  * Login as root via SSH on 192.168.1.1
 +  * Use the following commands to upgrade.
 +
 +<​code>​
 +cd /tmp/
 +wget http://​downloads.openwrt.org/​snapshots/​trunk/​brcm63xx/​openwrt-CT6373-squashfs-cfe.bin
 +sysupgrade /​tmp/​openwrt-CT6373-squashfs-cfe.bin
 +</​code>​
 +
 +  *If sysupgrade does not support this router, use the following commands.
 +
 +<​code>​
 +cd /tmp/
 +wget http://​downloads.openwrt.org/​snapshots/​trunk/​brcm63xx/​openwrt-CT6373-squashfs-cfe.bin
 +mtd write /​tmp/​openwrt-CT6373-squashfs-cfe.bin linux && reboot</​code>​
 +
 +===== Basic configuration =====
 +-> [[doc:​howto:​basic.config|Basic configuration]] After flashing, proceed with this.\\
 +Set up your Internet connection, configure wireless, configure USB port, etc.
 +
 +
 +===== Specific Configuration =====
 +==== Interfaces ====
 +
 +The default network configuration is:
 +^ Interface Name ^ Description ^ Default configuration ^
 +| br-lan | LAN & WiFi | 192.168.1.1/​24 | 
 +| eth0 | LAN ports (1 to 4) | None | 
 +| wlan0 | WiFi | Disabled | 
 +
 +==== Switch Ports (for VLANs) ====
 +This is an example to configure the switch: numbers 0-2 will be lan, labeled as Ports 1-3 on the unit, number 3 will be the 
 +Internet (WAN), 5 is the internal connection to the router itself. Don't be fooled: vlan0 = eth0.0, vlan1 = eth0.1 and so on.
 +
 +^ Port    ^ Switch port   ^ Mode             ^
 +| LAN 1   | 0             | lan              |
 +| LAN 2   | 1             | lan              |
 +| LAN 3   | 2             | lan              |
 +| LAN 4   | 3             | Internet (WAN)   |
 +
 +path: /​etc/​config/​network
 +
 +<​code>​
 +# port 4 = WAN
 +
 +config interface loopback
 +        option ifname ​  lo
 +        option proto    static
 +        option ipaddr ​  ​127.0.0.1
 +        option netmask ​ 255.0.0.0
 +
 +config interface lan
 +        option type     ​bridge
 +        option ifname ​  ​eth0.0
 +        option proto    static
 +        option ipaddr ​  ​192.168.1.1
 +        option netmask ​ 255.255.255.0
 +        option nat      1
 +
 +config interface wan
 +        option ifname eth0.1
 +        option macaddr 00:​11:​22:​33:​44:​55
 +        option proto dhcp 
 +        option defaultroute 1
 +
 +
 +config switch eth0
 + option enable 1
 + option reset 1
 + option enable_vlan 1
 +
 +config switch_vlan
 + option device eth0
 + option vlan 0
 + option ports "0 1 2 5t"
 +
 +config switch_vlan
 + option device eth0
 + option vlan 1
 + option ports "3 5t"
 +</​code>​
 +
 +
 +==== Failsafe mode ====
 +-> [[doc:​howto:​generic.failsafe]]
 +
 +==== Buttons ====
 +-> [[doc:​howto:​hardware.button]] on howto use and configure the hardware button(s).
 +
 +The Comtrend 6373 has one button: Reset.
 +^ BUTTON ​  ^ Event   ^
 +| Reset    | reset   |
 +
 +
 +===== Hardware =====
 +==== Info ====
 +| **[[wp>​Instruction set|Instruction set]]:** | [[wp>​MIPS architecture|MIPS]] ​ |
 +| **Vendor:​** ​                                | [[wp>​Broadcom]] ​               |
 +| **[[doc:​techref:​Bootloader]]:​** ​            | [[doc:​techref:​bootloader:​CFE#​bcm63xx_cfe|CFE]] ​  |
 +| **[[doc:​hardware:​soc|System-On-Chip]]:​** ​   | BCM6358 |
 +| **[[doc:​hardware:​cpu|CPU]]/​Speed** ​         | BMIPS4350 V1.0 / 300 Mhz [[doc:​hardware:​soc:​soc.broadcom.bcm63xx:​smp|BMIPS Dual Core]] |
 +| **Flash-Chip:​** ​  | M29W640FB ​                                               |
 +| **Flash size:​** ​  | 8 MiB                                                    |
 +| **RAM-Chip :**    | MIRA P3S56D40ETP-G5 / DDR-400 ​                           |
 +| **RAM size :**    | 32 MiB                                                   |
 +| **Wireless:​** ​    | Broadcom 4318, newer version: Broadcom 4322 (mini-pci) ​  |
 +| **Wireless standard:** | 802.11b/g, newer version 802.11b/g/n |
 +| **Ethernet:​** ​  | Broadcom ​ {{:​media:​datasheets:​bcm5325_pinout.png?​linkonly|BCM5325}} w/ vlan support [[doc:​uci:​network#​swconfig]] |
 +| **Internet:​** ​  | G.DMT/​ADSL/​ADSL2+ ​                              |
 +| **VoIP:​** ​      | Zarlink Le88266DLC ​                             |
 +| **USB:​** ​       | 1x2.0H + 1x1.1D, not exposed on newer version ​  |
 +| **[[doc:​hardware:​port.serial|Serial]]:​** ​  | [[#​Serial|Yes]] ​                                |
 +| **[[doc:​hardware:​port.jtag|JTAG]]:​** ​      | [[#​JTAG|?​]] ​                                    |
 +
 +==== Photos ====
 +Model Number
 +<​sortable>​
 +| Front | Back |
 +| {{media:​comtrend:​ct-6373:​ct-6373_front.jpg?​300}} | {{media:​comtrend:​ct-6373:​ct-6373_back.jpg?​300}} |
 +</​sortable>​
 +
 +==== Opening the case ====
 +**Note:** This will void your warranty!
 +
 +  *To remove the cover do a/b/c
 +
 +//Main PCB//
 +| Top View | Bottom View |
 +| {{media:​comtrend:​ct-6373:​ct-6373_board.jpg?​300}} | {{media:​comtrend:​ct-6373:​ct-6373_board_back.jpg?​300}} |
 +| LED controller, driven by GPIOs | Flash chip |
 +| {{media:​comtrend:​ct-6373:​ct-6373_gpioctrl.jpg?​300}} | {{media:​comtrend:​ct-6373:​ct-6373_flash.jpg?​300}} |
 +
 +
 +==== Serial ====
 +-> [[doc:​hardware:​port.serial]] general information about the serial port, serial port cable, etc.
 +
 +How to connect to the Serial Port of this specific device:
 +
 +{{media:​comtrend:​serial.jpg|}}
 +
 +==== JTAG ====
 +-> [[doc:​hardware:​port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +How to connect to the JTAG Port of this specific device:
 +
 +**Photo of PCB with markings**
 +
 +
 +===== Debricking =====
 +-> [[doc:​howto:​generic.debrick]]
 +
 +===== Bootloader Mods =====
 +  - you could read about [[doc:​techref:​bootloader]] in general
 +
 +| {{:​meta:​icons:​tango:​dialog-information.png?​nolink&​32X32}} |This is the bootloader backup: [[https://​docs.google.com/​uc?​export=download&​id=0B-EMoBe-_OdBTi1nYVU3NkhHRHc|CFE-CT-6373.zip]] ​ --- //danitool 2012/02/15 13:34//|
 +
 +===== Hardware mods =====
 +  - as a beginner, you really should inform yourself about [[doc:​hardware:​soldering]] in general and then obtain some practical experience!
 +
 +==== 64MiB RAM Mod ====
 +Use a 64MB DDR-400 RAM chip to replace the 32MB RAM chip at the board. Use a RAM chip with the same bus with as the old one. You may also need to modify the bootlader at the offsets 0x010-0x013,​ a value of 0x6 means 64MB 1 CHIP. -> [[doc/​techref/​bootloader/​cfe#​bcm63xx_cfe|bcm63xx_cfe]]
 +
 +===== Bootlogs =====
 +==== OEM Bootlog ====
 +
 +<WRAP bootlog>
 +<​nowiki>​CFE version 1.0.37-10.1-1 for BCM96358 (32bit,​SP,​BE)
 +Build Date: Fri Jun 22 16:26:35 CST 2007 (root@rd4-linux)
 +Copyright (C) 2000-2006 Broadcom Corporation.
 +
 +Boot Address 0xbe000000
 +
 +Initializing Arena.
 +Initializing Devices.
 +Parallel flash device: name STM29W640FB,​ id 0x22fd, size 8192KB
 +CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
 +CPU running TP0
 +Total memory: 33554432 bytes (32MB)
 +
 +Total memory used by CFE:  0x80401000 - 0x805282D0 (1209040)
 +Initialized Data:          0x8041D950 - 0x8041FB00 (8624)
 +BSS Area:                  0x8041FB00 - 0x804262D0 (26576)
 +Local Heap:                0x804262D0 - 0x805262D0 (1048576)
 +Stack Area:                0x805262D0 - 0x805282D0 (8192)
 +Text (code) segment: ​      ​0x80401000 - 0x8041D948 (117064)
 +Boot area (physical): ​     0x00529000 - 0x00569000
 +Relocation Factor: ​        ​I:​00000000 - D:00000000
 +
 +Board IP address ​                 : 192.168.1.1:​ffffff00  ​
 +Host IP address ​                  : 192.168.1.100  ​
 +Gateway IP address ​               :   
 +Run from flash/host (f/h)         : f  ​
 +Default host run file name        : vmlinux  ​
 +Default host flash file name      : bcm963xx_fs_kernel  ​
 +Boot delay (0-9 seconds) ​         : 1  ​
 +Board Id (0-12) ​                  : CT6373-1  ​
 +Number of MAC Addresses (1-32) ​   : 11  ​
 +Base MAC Address ​                 : 64:​68:​xx:​xx:​xx  ​
 +PSI Size (1-64) KBytes ​           : 24  ​
 +Main Thread Number [0|1]          : 0  ​
 +
 +*** Press any key to stop auto run (1 seconds) ***
 +Auto run second count down: 0
 +Booting from only image (0xbe010000) ...
 +Code Address: 0x80010000, Entry Address: 0x801cc018
 +Decompression OK!
 +Entry at 0x801cc018
 +Closing network.
 +Starting program at 0x801cc018
 +Linux version 2.6.8.1 (adams@rd5-linux) (gcc version 3.4.2) #5 Fri Dec 11 15:11:56 CST 2009
 +Parallel flash device: name STM29W640FB,​ id 0x22fd, size 8192KB
 +CT6373-1 prom init
 +CPU revision is: 0002a010
 +Determined physical RAM map:
 + ​memory:​ 01fa0000 @ 00000000 (usable)
 +On node 0 totalpages: 8096
 +  DMA zone: 4096 pages, LIFO batch:1
 +  Normal zone: 4000 pages, LIFO batch:1
 +  HighMem zone: 0 pages, LIFO batch:1
 +Built 1 zonelists
 +Kernel command line: root=31:0 ro noinitrd console=ttyS0,​115200
 +brcm mips: enabling icache and dcache...
 +Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
 +Primary data cache 16kB 2-way, linesize 16 bytes.
 +PID hash table entries: 128 (order 7: 1024 bytes)
 +Using 150.000 MHz high precision timer.
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Allocating memory for DSP module core and initialization code
 +Allocated DSP module memory - CORE=0x8104ca80 SIZE=609696,​ INIT=0x0 SIZE=0
 +Memory: 29404k/​32384k available (1540k kernel code, 2936k reserved, 231k data, 72k init, 0k highmem)
 +KLOB Pool 1 Initialized:​ 1048576 bytes <​0x80e00000 ... 0x80f00000>​
 +Calibrating delay loop... 299.00 BogoMIPS
 +Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
 +Checking for '​wait'​ instruction... ​ unavailable.
 +NET: Registered protocol family 16
 +Total Flash size: 8192K with 135 sectors
 +File system address: 0xbe010100
 +Can't analyze prologue code at 8018fb64
 +usbcore: registered new driver hub
 +Initializing Cryptographic API
 +PPP generic driver version 2.4.2
 +NET: Registered protocol family 24
 +Using noop io scheduler
 +bcm963xx_mtd driver v1.0
 +PCI: Enabling device 0000:​00:​0a.0 (0000 -> 0002)
 +ehci_hcd 0000:​00:​0a.0:​ EHCI Host Controller
 +PCI: Setting latency timer of device 0000:​00:​0a.0 to 64
 +ehci_hcd 0000:​00:​0a.0:​ irq 18, pci mem c0000300
 +ehci_hcd 0000:​00:​0a.0:​ new USB bus registered, assigned bus number 1
 +PCI: cache line size of 32 is not supported by device 0000:​00:​0a.0
 +ehci_hcd 0000:​00:​0a.0:​ USB f.f enabled, EHCI 1.00, driver 2004-May-10
 +hub 1-0:1.0: USB hub found
 +hub 1-0:1.0: 2 ports detected
 +ohci_hcd: 2004 Feb 02 USB 1.1 '​Open'​ Host Controller (OHCI) Driver (PCI)
 +ohci_hcd: block sizes: ed 64 td 64
 +PCI: Enabling device 0000:​00:​09.0 (0000 -> 0002)
 +ohci_hcd 0000:​00:​09.0:​ OHCI Host Controller
 +PCI: Setting latency timer of device 0000:​00:​09.0 to 64
 +ohci_hcd 0000:​00:​09.0:​ irq 13, pci mem c0001400
 +ohci_hcd 0000:​00:​09.0:​ new USB bus registered, assigned bus number 2
 +hub 2-0:1.0: USB hub found
 +hub 2-0:1.0: 2 ports detected
 +usbcore: registered new driver usblp
 +drivers/​usb/​class/​usblp.c:​ v0.13: USB Printer Device Class driver
 +brcmboard: brcm_board_init entry
 +kerSysScreenPciDevices:​ 0x14e4:​0x4318:​(slot 1) detected
 +kerSysScreenPciDevices:​ 0x14e4:​0x6300:​(slot 9) detected
 +kerSysScreenPciDevices:​ 0x14e4:​0x6300:​(slot 10) detected
 +Invalid External Interrupt definition ​
 +Serial: BCM63XX driver $Revision: 3.00 $
 +ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
 +ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
 +NET: Registered protocol family 2
 +IP: routing cache hash table of 512 buckets, 4Kbytes
 +TCP: Hash tables configured (established 2048 bind 4096)
 +Initializing IPsec netlink socket
 +NET: Registered protocol family 1
 +NET: Registered protocol family 17
 +NET: Registered protocol family 15
 +Ebtables v2.0 registered
 +hub 1-0:1.0: over-current change on port 2
 +NET: Registered protocol family 8
 +NET: Registered protocol family 20
 +802.1Q VLAN Support v1.8 Ben Greear <​greearb@candelatech.com>​
 +All bugs added by David S. Miller <​davem@redhat.com>​
 +VFS: Mounted root (squashfs filesystem) readonly.
 +Freeing unused kernel memory: 72k freed
 +
 +init started: ​ BusyBox v1.00 (2009.12.11-03:​43+0000) multi-call binary
 +Algorithmics/​MIPS FPU Emulator v1.5
 +
 +
 +BusyBox v1.00 (2009.12.11-03:​43+0000) Built-in shell (msh)
 +Enter '​help'​ for a list of built-in commands.
 +
 +
 +Loading drivers and kernel modules... ​
 +
 +atmapi: module license '​Proprietary'​ taints kernel.
 +adsl: adsl_init entry
 +blaadd: blaa_detect entry
 +Broadcom BCMPROCFS v1.0 initialized
 +Broadcom BCM6358A1 Ethernet Network Device v0.3 Dec 11 2009 11:37:53
 +Config Ethernet Switch Through MDIO Pseudo PHY Interface
 +dgasp: kerSysRegisterDyingGaspHandler:​ eth0 registered ​
 +eth0: MAC Address: 64:​68:​0C:​xx:​xx:​xx
 +Broadcom BCM6358A1 USB Network Device v0.4 Dec 11 2009 11:37:55
 +usb0: MAC Address: 64 68 0C xx xx xx
 +usb0: Host MAC Address: 64 68 0C xx xx xx
 +PCI: Setting latency timer of device 0000:​00:​01.0 to 64
 +PCI: Enabling device 0000:​00:​01.0 (0004 -> 0006)
 +wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.5.cpe2.0
 +dgasp: kerSysRegisterDyingGaspHandler:​ wl0 registered ​
 +DSP Driver: DSP init stub
 +Endpoint: endpoint_init entry
 +BOS: Enter bosInit ​
 +Enter bosAppInit ​
 +Exit bosAppInit ​
 +BOS: Exit bosInit ​
 +Endpoint: endpoint_init COMPLETED
 +BcmAdsl_Initialize=0xC006A3F8,​ g_pFnNotifyCallback=0xC00893F4
 +AnnexCParam=0x7FFF78E0 AnnexAParam=0x00003980 adsl2=0x00000000
 +pSdramPHY=0xA1FFFFF8,​ 0x3024B 0xD68DF64F
 +AdslCoreSharedMemInit:​ shareMemAvailable=20624
 +AdslCoreHwReset: ​ AdslOemDataAddr = 0xA1FEFDAC
 +AnnexCParam=0x7FFF78E0 AnnexAParam=0x00003980 adsl2=0x00000000
 +dgasp: kerSysRegisterDyingGaspHandler:​ dsl0 registered ​
 +atmapi: prioritize receive packets
 +ATM proc init !!!
 +Loading boot image .. done
 +Loading target image through HMI: done
 +bind now the file descriptor from IP 0.0.0.0, my port 57665.
 +socket init is now finished
 +vdslctl: Started successfully
 +
 +==> ​  ​Bcm963xx VDSL Software Version: 09.07.29, 2009-04-03 ​  <​==
 +
 +
 +==> ​  ​Comtrend Router Software Version: I131-S310CTL-C03_R02 ​  <​==
 +
 +device usb0 entered promiscuous mode
 +br0: port 1(usb0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 1(usb0) entering forwarding state
 +device eth0 entered promiscuous mode
 +br0: port 2(eth0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 2(eth0) entering forwarding state
 +Setting SSID "​WLAN"​
 +Setting country code using abbreviation:​ "​AT"​
 +wlctl: Not Found
 +wlctl: Not Found
 +wlctl: Not Found
 +KLOB extended to 2 pools
 +device wl0 entered promiscuous mode
 +br0: port 3(wl0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 3(wl0) entering forwarding state
 +device usb0 left promiscuous mode
 +br0: port 1(usb0) entering disabled state
 +device eth0 left promiscuous mode
 +br0: port 2(eth0) entering disabled state
 +device wl0 left promiscuous mode
 +br0: port 3(wl0) entering disabled state
 +device usb0 entered promiscuous mode
 +br0: port 1(usb0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 1(usb0) entering forwarding state
 +device eth0 entered promiscuous mode
 +br0: port 2(eth0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 2(eth0) entering forwarding state
 +device wl0 entered promiscuous mode
 +br0: port 3(wl0) entering learning state
 +br0: topology change detected, propagating
 +br0: port 3(wl0) entering forwarding state
 +
 +Voice App. Comparing interface: current br0 (3) - passed br0.
 +
 +Voice App. Comparing interface: current br0 (3) - passed br0.
 +Sorry, rule does not exist.
 +Sorry, rule does not exist.
 +Sorry, rule does not exist.
 +Starting the SIP application with the following parameters:
 +
 +
 +
 +SIP Proxy (IP address or FQDN): ​
 +
 +SIP Proxy port: 5060
 +
 +SIP Outbound Proxy (IP address or FQDN): ​
 +
 +SIP Outbound Proxy port: 5060
 +
 +SIP Registrar (IP address or FQDN): ​
 +
 +SIP Registrar Port port: 5060
 +
 +Enable SIP tag matching: No
 +
 +Log IP address: 192.168.1.4
 +
 +Log port: 514
 +
 +Music server address: 0.0.0.0
 +
 +Music server port: 0
 +
 +PSTN number of channels: 1
 +
 +PSTN routing: LINE1
 +
 +PSTN routing data: 0
 +
 +Extension 1: 
 +
 +Password 1: 
 +
 +Extension 2: Disabled
 +
 +Password 2: Disabled
 +
 +Extension 3: Disabled
 +
 +Password 3: Disabled
 +
 +Extension 4: Disabled
 +
 +Password 4: Disabled
 +
 +Max Digits: 24
 +
 +Interface name: br0
 +
 +Domain name: 
 +
 +Locale name: DEU
 +
 +Pref. codec: none
 +
 +Pref. ptime: 20
 +
 +Console log level: 5
 +
 +Register Expire Time: 120
 +
 +Max Digits: 24
 +
 +Line 1 call forwarding number: ​
 +
 +Line 1 call forwarding busy:      Disabled
 +
 +Line 1 call forwarding all:       ​Disabled
 +
 +Line 1 call forwarding no answer: Disabled
 +
 +Line 1 call waiting: ​             Enabled
 +
 +Line 2 call forwarding number: Not available
 +
 +Line 2 call forwarding busy:      Disabled
 +
 +Line 2 call forwarding all:       ​Disabled
 +
 +Line 2 call forwarding no answer: Disabled
 +
 +Line 2 call waiting: ​             Enabled
 +
 +BOS: Enter bosInit ​
 +bosTimerInit
 +Enter bosAppInit ​
 +Exit bosAppInit ​
 +BOS: Exit bosInit ​
 +Created queue CFGMGR_Q ​
 +00:00:30 Init Configuration Manager: CFGMGR_VOIP_RETCODE_SUCCESS
 +00:00:30 Setting provisioning default values.
 +
 +option 7, cfx1 = 
 +option 5
 +option A callfwd busy = 0
 +option A callfwd all = 0
 +option A callfwd no answer = 0
 +option A callwaiting = 15
 +Sip registration timeout = 120Sip transport protocol = 1User line enabled = 10
 +user line 1 mwi enabled = 1
 +user line 2 mwi enabled = 1
 +user line 3 mwi enabled = 1
 +user line 4 mwi enabled = 1
 +Codec name = G711A, encoder=0x2,​ parm=0
 +Codec name = G711U, encoder=0x1,​ parm=1
 +Codec name = G729, encoder=0x4000,​ parm=2
 +dtmf relay method = 0
 +T38 disabled ​
 +VAD enabled ​
 +00:00:30 Process 593 priority is 0
 +00:00:30 Process 593: old priority 0, new priority -15
 +Enter TaskCreate VRGCMGR
 +TaskCreate - spawn new task VRGCMGR
 +Exit TaskCreate ​
 +KLOB extended to 3 pools
 +br0: port 2(eth0) entering disabled state
 +kernel::​endpoint_open
 +kernel::​endpoint_open COMPLETED
 +00:00:30 Endpoint Event task started with pid 605...
 +
 +00:00:30 Endpoint Packet task started with pid 606 ...
 +
 +Enter bosStartApp
 +br0: port 1(usb0) entering disabled state
 +
 +
 +bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)...
 +
 +
 +
 +bosAppRootTask() - Is it morning already? Spawning app task (epoch #0)...
 +
 +Enter TaskCreate aoAP
 +TaskCreate - spawn new task aoAP
 +Exit bosStartApp
 +Exit TaskCreate ​
 +AppResetDetectionEnable() - Enabled reset detection.
 +PLL init completed. PLL registers set to:
 +PCM->​pcm_pll_ctrl1 ​      = 0x00020001 ​
 +PCM->​pcm_pll_ctrl2 ​      = 0x0008492B ​
 +PCM->​pcm_pll_ctrl3 ​      = 0x00001E1C ​
 +Set up PCM registers
 +Channel 0 assigned to timeslot 0
 +Channel 1 assigned to timeslot 1
 +Channel 2 assigned to timeslot 2
 +Tx Desc (0xA0819000):​ chan 0, buf 0, sts 0xe000, len 1280, bufp 0xdab000 ​
 +Tx Desc (0xA0819008):​ chan 0, buf 1, sts 0x7000, len 1280, bufp 0xdab510 ​
 +Rx Desc (0xA02AA000):​ chan 0, buf 0, sts 0x8000, len 1280, bufp 0x2a8000 ​
 +Rx Desc (0xA02AA008):​ chan 0, buf 1, sts 0x9000, len 1280, bufp 0x2a8510 ​
 +initIudma: chan 0, descBase 0xa02aa000, descBaseIudma 0x2aa000
 +initIudma: chan 1, descBase 0xa0819000, descBaseIudma 0x819000
 +rm: cannot remove `/​var/​fyi/​sys/​gateway':​ No such file or directory
 +rm: cannot remove `/​var/​fyi/​sys/​dns':​ No such file or directory
 +Clean Up IP Connection Tracking Table
 +PCM ENABLE INFO: DMA0 IRQ STATUS 0x00000000
 +PCM ENABLE INFO: DMA0 IRQ MASK   ​0x00000005
 +PCM ENABLE INFO: DMA1 IRQ STATUS 0x00000000
 +PCM ENABLE INFO: DMA1 IRQ MASK   ​0x00000005
 +PCM ENABLE INFO: PCM  IRQ MASK    0x00000003
 +PCM ENABLE INFO: PCM  IRQ PENDING 0x00000007
 +Enter TaskCreate CMT_EXCEPTION_IST
 +TaskCreate - spawn new task CMT_EXCEPTION_IST
 +cat: /​proc/​clean_ip_conntrack:​ No such file or directory
 +Voice QoS: registering interface br0 for voice
 +Exit TaskCreate ​
 +regStatus (reg 12 sel 0)    = 0x10008501 ​
 +regStatus (reg 12 sel 7)    = 0x00000101 ​
 +regCause ​ (reg 13 sel 0)    = 0x00000000 ​
 +regCause ​ (reg 13 sel 7)    = 0x00808000 ​
 +regCMT ​   (reg 22 sel 0)    = 0xe30e1006 ​
 +regCMT ​   (reg 22 sel 1)    = 0x10008001 ​
 +Kicking off secondary thread processor at entry point 0x8104CAC0...
 +Secondary thread processor entry point at 0x8104cac0
 +Thread processor handshake. Secondary app initialized properly.
 +Enter TaskCreate HTSK
 +TaskCreate - spawn new task HTSK
 +rm: cannot remove `/​var/​fyi/​sys/​gateway':​ No such file or directory
 +rm: cannot remove `/​var/​fyi/​sys/​dns':​ No such file or directory
 +Clean Up IP Connection Tracking Table
 +cat: /​proc/​clean_ip_conntrack:​ No such file or directory
 +Exit TaskCreate ​
 +SUCCESS: Took semaphore
 +SUCCESS: Gave semaphore
 +INFO: MSPI POLLING MODE
 +INFO: IRQ MASK 0xe0082ca4
 +INFO: IRQ STATUS 0x420000
 +INFO: BLOCK ENABLES 0x3e0f20
 +Read data from Rev ID register: 0x4, 0xb3
 +OpenSlic: country code = 9
 +
 +SLIC LE88221 Registers...
 +
 +0x41: Tx TSlt.........0x0
 +0x43: Rx TSlt.........0x0
 +0x45: ClkSlt TxEdge...0x40
 +0x47: Device Config...0x2
 +0x4B: ChEna OpMode....0x3
 +0x4F: Signaling.......0x0 0x0
 +0x51: Voice Gain......0x10
 +0x53: I/O Data........0x0
 +0x55: I/O Direction...0x2
 +0x57: Sys State.......0x0
 +0x61: Oper Func.......0xBF
 +0x69: Sys State Cfg...0x9
 +0x6D: Int Mask........0x1F
 +0x71: Oper Cond.......0xFF
 +0x73: Revision........0x4 0xB3
 +0x81: GX Filter.......0xA3B3
 +0x83: GR Filter.......0x3AA1
 +0x87: B FIR Filter....0x725A22241AA1BB22B32B4AA5BB60
 +0x89: X Filter........0x4BD0AA44B22DAB2D2AB42AAD
 +0x8B: R FIR Filter....0x2E12C0A448322B22A1A2BA43B4
 +0x97: B IIR Filter....0xB4A1
 +0x99: Z FIR Filter....0x2D51CA325BCBB8FAB363
 +0x9B: Z IIR Filter....0xAAF3579F1
 +0xA7: Conv Config.....0x0
 +0xC3: Loop Super......0x1B84B35
 +0xC7: DC Feed.........0x138
 +0xCB: DISN............0xE7
 +0xD1: Metering........0x213D3C0
 +0xD3: Gen A/B &​Bias...0x00003736460000
 +0xD5: Gen A/B &​Bias...0x177727D4CCD27D4
 +0xDF: SigGen Ctl......0x0
 +0xE1: Cadence Tmr.....0x190320
 +0xE3: Caller ID.......0x0
 +0xE5: Switch Reg......0x058
 +0xE7: Sw Reg Ctrl.....0x5
 +0xEB: CID Parms.......0x3
 +----------------
 +OpenSlic: country code = 9
 +
 +SLIC LE88221 Registers...
 +
 +0x41: Tx TSlt.........0x0
 +0x43: Rx TSlt.........0x0
 +0x45: ClkSlt TxEdge...0x40
 +0x47: Device Config...0x2
 +0x4B: ChEna OpMode....0x3
 +0x4F: Signaling.......0x0 0x0
 +0x51: Voice Gain......0x10
 +0x53: I/O Data........0x0
 +0x55: I/O Direction...0x2
 +0x57: Sys State.......0x0
 +0x61: Oper Func.......0xBF
 +0x69: Sys State Cfg...0x9
 +0x6D: Int Mask........0x1F
 +0x71: Oper Cond.......0xFF
 +0x73: Revision........0x4 0xB3
 +0x81: GX Filter.......0xA3B3
 +0x83: GR Filter.......0x3AA1
 +0x87: B FIR Filter....0x725A22241AA1BB22B32B4AA5BB60
 +0x89: X Filter........0x4BD0AA44B22DAB2D2AB42AAD
 +0x8B: R FIR Filter....0x2E12C0A448322B22A1A2BA43B4
 +0x97: B IIR Filter....0xB4A1
 +0x99: Z FIR Filter....0x2D51CA325BCBB8FAB363
 +0x9B: Z IIR Filter....0xAAF3579F1
 +0xA7: Conv Config.....0x0
 +0xC3: Loop Super......0x1B84B35
 +0xC7: DC Feed.........0x138
 +0xCB: DISN............0xE7
 +0xD1: Metering........0x213D3C0
 +0xD3: Gen A/B &​Bias...0x00003736460000
 +0xD5: Gen A/B &​Bias...0x177727D4CCD27D4
 +0xDF: SigGen Ctl......0x0
 +0xE1: Cadence Tmr.....0x190320
 +0xE3: Caller ID.......0x0
 +0xE5: Switch Reg......0x058
 +0xE7: Sw Reg Ctrl.....0x5
 +0xEB: CID Parms.......0x3
 +----------------
 +DAA Device Init reset don't need. 
 +     DAA DBG: Successful READ!!!! count = 0 
 + DAA DBG: ISOCAP lock count = 0 
 +Si3050 SLAC Initialised,​ Line side device = Si: Unknown (0x4)
 +System dev rev: 0x4, Line dev rev: 0x6
 +Line dev status: FDT:0x1, LCS: 0x0
 +DAA initialized with country code 9
 +
 +Si3050 Registers Values
 +
 + Reg 0x1. Control 1  - 0x0 (Res 0xba)
 + Reg 0x2. Control 2  - 0x7 (Res 0xdf)
 + Reg 0x3. Int Mask   - 0x80 (Res 0xff)
 + Reg 0x4. Int Source - 0x0 (Res 0xff)
 + Reg 0x5. DAA Ctrl 1 - 0x0 (Res 0x6d)
 + Reg 0x6. DAA Ctrl 2 - 0x0 (Res 0x18)
 + Reg 0x7. Smp Rate   - 0x0 (Res 0x8)
 + Reg 0x8. Reserved ​  - 0x0 (Res 0x0)
 + Reg 0x9. Reserved ​  - 0x0 (Res 0x0)
 + Reg 0xa. DAA Ctrl 3 - 0x0 (Res 0x1)
 + Reg 0xb. S/LSD Rev  - 0x44 (Res 0xff)
 + Reg 0xc. LSD Status - 0x40 (Res 0x5f)
 + Reg 0xd. LSD Rev    - 0x58 (Res 0x3c)
 + Reg 0xe. DAA Ctrl 4 - 0x0 (Res 0x2)
 + Reg 0xf. T/R Gain 1 - 0x0 (Res 0x88)
 + Reg 0x10. Int Ctrl 1 - 0x0 (Res 0x53)
 + Reg 0x11. Int Ctrl 2 - 0x0 (Res 0xff)
 + Reg 0x12. Int Ctrl 3 - 0x0 (Res 0x2)
 + Reg 0x13. Int Ctrl 4 - 0x2 (Res 0x7)
 + Reg 0x14. CP Rx Atte - 0x0 (Res 0xff)
 + Reg 0x15. CP Tx Atte - 0x0 (Res 0xff)
 + Reg 0x16. Rg Ctrl 1  - 0x96 (Res 0xff)
 + Reg 0x17. Rg Ctrl 2  - 0x13 (Res 0xff)
 + Reg 0x18. Rg Ctrl 3  - 0x99 (Res 0xbf)
 + Reg 0x19. Res Calib  - 0x9 (Res 0xef)
 + Reg 0x1a. DC Ctrl    - 0xc2 (Res 0xf3)
 + Reg 0x1b. Reserved ​  - 0x7 (Res 0x0)
 + Reg 0x1c. Loop Sta   - 0x0 (Res 0xff)
 + Reg 0x1d. Line V Sta - 0x0 (Res 0xff)
 + Reg 0x1e. AC Ctrl    - 0x3 (Res 0xf)
 + Reg 0x1f. DAA Ctrl 5 - 0x28 (Res 0xeb)
 + Reg 0x20. Gd Sta Ctl - 0x7 (Res 0x7)
 + Reg 0x21. PCM/SPI Md - 0x38 (Res 0xfb)
 + Reg 0x22. PCM T St L - 0x21 (Res 0xff)
 + Reg 0x23. PCM T St H - 0x0 (Res 0x3)
 + Reg 0x24. PCM R St L - 0x21 (Res 0xff)
 + Reg 0x25. PCM R St H - 0x0 (Res 0x3)
 + Reg 0x26. T Gain 2   - 0x0 (Res 0x1f)
 + Reg 0x27. R Gain 2   - 0x0 (Res 0x1f)
 + Reg 0x28. T Gain 3   - 0x0 (Res 0x1f)
 + Reg 0x29. R Gain 3   - 0x0 (Res 0x1f)
 + Reg 0x2a. GCI Ctrl   - 0x0 (Res 0xf)
 + Reg 0x2b. LV T Int   - 0x0 (Res 0xff)
 + Reg 0x2c. LV T IntC  - 0x0 (Res 0xf)
 + Reg 0x2d. Prg Hyb 1  - 0x0 (Res 0xff)
 + Reg 0x2e. Prg Hyb 2  - 0x0 (Res 0xff)
 + Reg 0x2f. Prg Hyb 3  - 0x0 (Res 0xff)
 + Reg 0x30. Prg Hyb 4  - 0x0 (Res 0xff)
 + Reg 0x31. Prg Hyb 5  - 0x0 (Res 0xff)
 + Reg 0x32. Prg Hyb 6  - 0x0 (Res 0xff)
 + Reg 0x33. Prg Hyb 7  - 0x0 (Res 0xff)
 + Reg 0x34. Prg Hyb 8  - 0x0 (Res 0xff)
 + Reg 0x35. Reserved ​  - 0x0 (Res 0x0)
 + Reg 0x36. Reserved ​  - 0x0 (Res 0x0)
 + Reg 0x37. Reserved ​  - 0x0 (Res 0x0)
 + Reg 0x38. Reserved ​  - 0xf (Res 0x0)
 + Reg 0x39. Reserved ​  - 0x0 (Res 0x0)
 + Reg 0x3a. Reserved ​  - 0x0 (Res 0x0)
 + Reg 0x3b. SQC        - 0x0 (Res 0x50)
 +
 +DAA Device Init completed. ​
 +boardHalInit completed
 +Enter TaskCreate HRTBEAT
 +TaskCreate - spawn new task HRTBEAT
 +Exit TaskCreate ​
 +bosMsgQCreate:​ Created message queue VRGEVQ at address 0x8001 ​
 +Enter TaskCreate VRGEVPR
 +TaskCreate - spawn new task VRGEVPR
 +Exit TaskCreate ​
 +Enter TaskCreate HCAS
 +TaskCreate - spawn new task HCAS
 +Exit TaskCreate ​
 +*** gStartRxDesc[0] = 0xA02AA000 ​
 +*** gBufferSizeBytes = 1280 
 +*** gStartTxDesc[0] = 0xA0819000 ​
 +hal6358PcmInit 260 nextTxDesc = 0xA0819000 ​
 +hal6358PcmInit 260 nextTxDesc = 0xA0819008 ​
 +hal6358PcmInit 264 Ownership for TX desc not set. Use this buffer. ​
 +PERF->​IrqMask ​  = 0xE0082CA4 ​
 +PERF->​IrqMask1 ​ = 0x00800000 ​
 +bosMsgQCreate:​ Created message queue PSTN_CTL_EVQ at address 0x10002 ​
 +Enter TaskCreate PSTN
 +TaskCreate - spawn new task PSTN
 +Exit TaskCreate ​
 +dgasp: kerSysRegisterDyingGaspHandler:​ endpoint registered ​
 +DAA: Enable on-hook Caller ID receive. ​
 +routing data index = 0
 +Setting egress: 0, ingress: 0
 +kernel: DoVrgEndptGetHookStatus() ​
 +kernel: DoVrgEndptSetRelayStat() ​
 + ​Active relay on channel 0 pin = 256 
 + ​Active relay on channel 1 pin = 256 
 +kernel: DoVrgEndptGetHookStatus() ​
 +kernel: DoVrgEndptSetRelayStat() ​
 + ​Active relay on channel 0 pin = 256 
 + ​Active relay on channel 1 pin = 256 
 +00:​00:​33 ​ RTCP thread started with pid 706 </​nowiki>​
 +</​WRAP>​\\
 +
 +==== OpenWrt Bootlog ====
 +
 +<WRAP bootlog>
 +<​nowiki>​root@OpenWrt:​~#​ dmesg
 +[    0.000000] Linux version 3.0.18 (dani@tool) (gcc version 4.5.4 20120105 (prerelease) (Linaro GCC 4.5-2012.01) ) #3 Tue Feb 14 12:19:57 CET 2012
 +[    0.000000] Detected Broadcom 0x6358 CPU revision a1
 +[    0.000000] CPU frequency is 300 MHz
 +[    0.000000] 32MB of RAM installed
 +[    0.000000] registering 40 GPIOs
 +[    0.000000] board_bcm963xx:​ Boot address 0xbe000000
 +[    0.000000] board_bcm963xx:​ CFE version: 1.0.37-10.1
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
 +[    0.000000] board_bcm963xx:​ board name: CT6373-1
 +[    0.000000] Determined physical RAM map:
 +[    0.000000] ​ memory: 02000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone PFN ranges:
 +[    0.000000] ​  ​Normal ​  ​0x00000000 -> 0x00002000
 +[    0.000000] Movable zone start PFN for each node
 +[    0.000000] early_node_map[1] active PFN ranges
 +[    0.000000] ​    0: 0x00000000 -> 0x00002000
 +[    0.000000] On node 0 totalpages: 8192
 +[    0.000000] free_area_init_node:​ node 0, pgdat 8027b600, node_mem_map 81000000
 +[    0.000000] ​  ​Normal zone: 64 pages used for memmap
 +[    0.000000] ​  ​Normal zone: 0 pages reserved
 +[    0.000000] ​  ​Normal zone: 8128 pages, LIFO batch:0
 +[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
 +[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 +[    0.000000] pcpu-alloc: [0] 0 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
 +[    0.000000] Kernel command line:  root=/​dev/​mtdblock2 rootfstype=squashfs,​jffs2 noinitrd console=ttyS0,​115200
 +[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
 +[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] Memory: 29568k/​32768k available (2121k kernel code, 3200k reserved, 358k data, 160k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
 +[    0.036000] pid_max: default: 32768 minimum: 301
 +[    0.040000] Mount-cache hash table entries: 512
 +[    0.052000] NET: Registered protocol family 16
 +[    0.064000] registering PCI controller with io_map_base unset
 +[    0.072000] bio: create slab <​bio-0>​ at 0
 +[    0.080000] pci 0000:​00:​01.0:​ [14e4:4318] type 0 class 0x000280
 +[    0.080000] pci 0000:​00:​01.0:​ reg 10: [mem 0x00000000-0x00001fff]
 +[    0.096000] pci 0000:​00:​01.0:​ BAR 0: assigned [mem 0x30000000-0x30001fff]
 +[    0.100000] pci 0000:​00:​01.0:​ BAR 0: set to [mem 0x30000000-0x30001fff] (PCI address [0x30000000-0x30001fff])
 +[    0.104000] Switching to clocksource MIPS
 +[    0.116000] PCI: Enabling device 0000:​00:​01.0 (0000 -> 0002)
 +[    0.120000] PCI: Setting latency timer of device 0000:​00:​01.0 to 64
 +[    0.144000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
 +[    0.144000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
 +[    0.144000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
 +[    0.144000] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
 +[    0.192000] ssb: Sonics Silicon Backplane found on PCI device 0000:​00:​01.0
 +[    0.200000] NET: Registered protocol family 2
 +[    0.204000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.212000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
 +[    0.220000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.228000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.236000] TCP reno registered
 +[    0.236000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.244000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.252000] NET: Registered protocol family 1
 +[    0.256000] PCI: CLS 0 bytes, default 32
 +[    0.260000] audit: initializing netlink socket (disabled)
 +[    0.264000] type=2000 audit(0.264:​1):​ initialized
 +[    0.272000] squashfs: version 4.0 (2009/​01/​31) Phillip Lougher
 +[    0.276000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.288000] msgmni has been set to 57
 +[    0.292000] io scheduler noop registered
 +[    0.296000] io scheduler deadline registered (default)
 +[    0.304000] bcm63xx_uart.0:​ ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
 +[    0.312000] console [ttyS0] enabled, bootconsole disabled
 +[    0.324000] gpiodev: gpio device registered with major 254
 +[    0.332000] bcm963xx-flash bcm963xx-flash.0:​ 0x02000000 at 0x1e000000
 +[    0.340000] bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000020 Chip ID 0x0022fd
 +[    0.352000] bcm963xx: Found an alias at 0x800000 for the chip at 0x0
 +[    0.352000] bcm963xx: Found an alias at 0x1000000 for the chip at 0x0
 +[    0.352000] bcm963xx: Found an alias at 0x1800000 for the chip at 0x0
 +[    0.352000] Amd/Fujitsu Extended Query Table at 0x0040
 +[    0.356000] ​  ​Amd/​Fujitsu Extended Query version 1.3.
 +[    0.360000] number of CFI chips: 1
 +[    0.364000] bcm963xx_flash:​ Read Signature value of CFE1CFE1
 +[    0.372000] bcm963xx-flash bcm963xx-flash.0:​ CFE bootloader detected
 +[    0.376000] bcm963xx_flash:​ CFE boot tag found with version 6 and board type CT6373-1
 +[    0.384000] bcm963xx_flash:​ Partition 0 is CFE offset 0 and length 10000
 +[    0.392000] bcm963xx_flash:​ Partition 1 is kernel offset 10100 and length dff00
 +[    0.400000] bcm963xx_flash:​ Partition 2 is rootfs offset f0000 and length 700000
 +[    0.408000] bcm963xx_flash:​ Partition 3 is nvram offset 7f0000 and length 10000
 +[    0.416000] bcm963xx_flash:​ Partition 4 is linux offset 10000 and length 7e0000
 +[    0.424000] bcm963xx_flash:​ Spare partition is 320000 offset and length 4d0000
 +[    0.428000] Creating 5 MTD partitions on "​bcm963xx":​
 +[    0.436000] 0x000000000000-0x000000010000 : "​CFE"​
 +[    0.444000] 0x000000010100-0x0000000f0000 : "​kernel"​
 +[    0.448000] mtd: partition "​kernel"​ must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    0.464000] 0x0000000f0000-0x0000007f0000 : "​rootfs"​
 +[    0.472000] mtd: partition "​rootfs"​ set to be root filesystem
 +[    0.480000] mtd: partition "​rootfs_data"​ created automatically,​ ofs=310000, len=4E0000 ​
 +[    0.488000] 0x000000310000-0x0000007f0000 : "​rootfs_data"​
 +[    0.496000] 0x0000007f0000-0x000000800000 : "​nvram"​
 +[    0.504000] 0x000000010000-0x0000007f0000 : "​linux"​
 +[    0.520000] bcm63xx_enet MII bus: probed
 +[    0.528000] bcm63xx-wdt bcm63xx-wdt.0: ​ started, timer margin: 30 sec
 +[    0.536000] TCP westwood registered
 +[    0.540000] NET: Registered protocol family 17
 +[    0.544000] 802.1Q VLAN Support v1.8
 +[    0.560000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    0.568000] Freeing unused kernel memory: 160k freed
 +[    3.240000] eth1: link forced UP - 100/full - flow control off/off
 +[    3.440000] roboswitch: Probing device eth0: 
 +[    3.444000] roboswitch: [/​media/​scsi/​kamikaze/​trunk/​build_dir/​linux-brcm63xx/​kmod-switch/​switch-robo.c:​121] SIOCGETCPHYRD failed!
 +[    3.456000] roboswitch: [/​media/​scsi/​kamikaze/​trunk/​build_dir/​linux-brcm63xx/​kmod-switch/​switch-robo.c:​121] SIOCGETCPHYRD failed!
 +[    3.468000] No Robo switch in managed mode found, phy_id = 0xffffffff
 +[    3.472000] roboswitch: Probing device eth1: found a 5325! It's a 5350.
 +[   ​12.184000] Compat-wireless backport release: compat-wireless-2012-01-16-14-g02166d5
 +[   ​12.192000] Backport based on wireless-testing.git master-2012-02-06
 +[   ​12.252000] cfg80211: Calling CRDA to update world regulatory domain
 +[   ​13.008000] cfg80211: World regulatory domain updated:
 +[   ​13.012000] cfg80211: ​  ​(start_freq - end_freq @ bandwidth), (max_antenna_gain,​ max_eirp)
 +[   ​13.020000] cfg80211: ​  ​(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​13.028000] cfg80211: ​  ​(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   ​13.036000] cfg80211: ​  ​(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   ​13.044000] cfg80211: ​  ​(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​13.052000] cfg80211: ​  ​(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   ​13.224000] SCSI subsystem initialized
 +[   ​13.520000] usbcore: registered new interface driver usbfs
 +[   ​13.528000] usbcore: registered new interface driver hub
 +[   ​13.536000] usbcore: registered new device driver usb
 +[   ​14.164000] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
 +[   ​14.240000] ieee80211 phy0: Selected rate control algorithm '​minstrel_ht'​
 +[   ​14.240000] Registered led device: b43-phy0::​tx
 +[   ​14.240000] Registered led device: b43-phy0::​rx
 +[   ​14.244000] Registered led device: b43-phy0::​radio
 +[   ​14.244000] Broadcom 43xx driver loaded [ Features: PL ]
 +[   ​14.276000] Button Hotplug driver version 0.4.1
 +[   ​15.116000] PPP generic driver version 2.4.2
 +[   ​15.632000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   ​15.972000] NET: Registered protocol family 24
 +[   ​16.184000] nf_conntrack version 0.5.0 (464 buckets, 1856 max)
 +[   ​16.836000] ohci_hcd: USB 1.1 '​Open'​ Host Controller (OHCI) Driver
 +[   ​16.844000] bcm63xx_ohci bcm63xx_ohci.0:​ BCM63XX integrated OHCI controller
 +[   ​16.852000] bcm63xx_ohci bcm63xx_ohci.0:​ new USB bus registered, assigned bus number 1
 +[   ​16.860000] bcm63xx_ohci bcm63xx_ohci.0:​ irq 13, io mem 0xfffe1400
 +[   ​16.924000] hub 1-0:1.0: USB hub found
 +[   ​16.928000] hub 1-0:1.0: 1 port detected
 +[   ​17.128000] Initializing USB Mass Storage driver...
 +[   ​17.136000] usbcore: registered new interface driver usb-storage
 +[   ​17.140000] USB Mass Storage support registered.
 +[   ​17.724000] hub 1-0:1.0: over-current condition
 +[   ​20.100000] bcm63xx_enet bcm63xx_enet.0:​ attached PHY at address 1 [Broadcom BCM63XX (2)]
 +[   ​21.328000] eth1: link forced UP - 100/full - flow control off/off
 +[   ​21.952000] device eth1 entered promiscuous mode
 +[   ​22.236000] br-lan: port 1(eth1) entering forwarding state
 +[   ​22.244000] br-lan: port 1(eth1) entering forwarding state
 +[   ​27.336000] device eth1 left promiscuous mode
 +[   ​27.340000] br-lan: port 1(eth1) entering forwarding state
 +[   ​28.048000] device eth1 entered promiscuous mode
 +[   ​28.052000] br-lan: port 1(eth1) entering forwarding state
 +[   ​28.056000] br-lan: port 1(eth1) entering forwarding state
 +[   ​42.120000] jffs2_scan_eraseblock():​ End of filesystem marker found at 0x0
 +[   ​42.136000] jffs2_build_filesystem():​ unlocking the mtd device... done.
 +[   ​42.140000] jffs2_build_filesystem():​ erasing all blocks after the end marker... done.
 +[   ​84.396000] JFFS2 notice: (1319) jffs2_build_xattr_subsystem:​ complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
 +root@OpenWrt:​~#​ </​nowiki>​
 +</​WRAP>​\\
 +
 +===== Notes =====
 +
 +The original firmware can have the following login:
 +<​code>​user:​ admin, pass: admin 
 +user: user, pass: user</​code>​
 +It does have SSH enabled by default and it's possible to disable this on the web interface.
 +
 +===== Tags =====
 +[[meta:​tags|How to add tags]]
 +{{tag>​bcm63xx bcm6358 FastEthernet 1NIC 1WNIC 4Port USB b43 32RAM 8Flash MIPS MIPS32 adsl2+}}