The VR-3025u is currently not supported!.

You must set your TCP/IP v4 protocol to:

1. IP: 192.168.1.2
2. Netmask: 255.255.255.0
3. Gateway: 192.168.1.1
4. DNS: (optional, can be blank).

Then:

1. Power off the router.
2. Press reset button near the antenna.
3. Keep it pressed while powering up during ~20+ seconds.
4. Acces to http://192.168.1.1 and upload binary file.
5. Wait until router reboots.

→ port.jtag general information about the JTAG port, JTAG cable, etc.

N/A

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Photo of PCB with markings

Read: System configuration: Leds to configure the leds

→ hardware.button on howto use and configure the hardware button(s).

N/A

CFE version 1.0.37-110.11-1 for BCM96368 (32bit,SP,BE) Build Date: 2011-04-12 17:31:15 (evan@broadcom_eu) Copyright (C) 2000-2009 Broadcom Corporation. Parallel flash device: name MX29GL256EH, id 0x2222 size 32768KB Total Flash size: 32768K with 256 sectors Chip ID: BCM6368B2, MIPS: 400MHz Main Thread: TP0 Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Boot image (0=latest, 1=previous) : 0 Board Id (0-15) : 96368M-1541N Number of MAC Addresses (1-32) : 32 Base MAC Address : XX:XX:XX:XX:XX:XX PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 0 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Serial Number : 1173025UXXF-AG018384 Default PSK key : BC4YBrpqGqPaEuYigmyA *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 110 Booting from latest image (0xb8020000) ... Code Address: 0x80010000, Entry Address: 0x80295840 Decompression OK! Entry at 0x80295840 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80295840 Linux version 2.6.30 (lain@SW1-BCM-04) (gcc version 4.4.2 (Buildroot 2010.02-git ) ) #1 Tue Nov 1 13:55:33 CST 2011 Parallel flash device: name MX29GL256EH, id 0x2222 size 32768KB 96368M-1541N prom init CPU revision is: 0002a031 (Broadcom4350) Determined physical RAM map: memory: 03f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003f00 On node 0 totalpages: 16128 free_area_init_node: node 0, pgdat 80321d50, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11938 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:128 PID hash table entries: 256 (order: 8, 1024 bytes) console [ttyS0] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 60352k/64512k available (2605k kernel code, 4140k reserved, 543k data, 1 24k init, 0k highmem) Calibrating delay loop... 399.36 BogoMIPS (lpj=199680) Mount-cache hash table entries: 512 --Kernel Config-- SMP=0 PREEMPT=0 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 Broadcom Logger v0.1 Nov 1 2011 13:53:42 net_namespace: 812 bytes NET: Registered protocol family 16 Total Flash size: 32768K with 256 sectors registering PCI controller with io_map_base unset bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x00ffff] pci 0000:00:09.0: reg 10 32bit mmio: [0x10001600-0x100016ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10001500-0x100015ff] BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Nov 1 2011 13:55:25 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher squashfs: version 4.0 with LZMA457 ported by BRCM fuse init (API version 7.11) msgmni has been set to 117 io scheduler noop registered (default) Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 File system address: 0xb8020100 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0x8017 is enabled Invalid External Interrupt definition Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX Total # RxBds=1648 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Nov 1 2011 13:55:07 GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 NET: Registered protocol family 15 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 124k freed init started: BusyBox v1.00 (2011.11.01-05:56+0000) multi-call binary BusyBox v1.00 (2011.11.01-05:56+0000) Built-in shell (msh) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... pktflow: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Nov 1 2011 13:54:03 Registered<242 > Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Nov 1 2011 13:54:03 CMF:CONFIG cmfConstruct: CMF:CONFIG pktDbgLvl[0xc008e5c4]=0 CMF:HAL pktCmfHalConstruct: CMF:HAL pktDbgLvl[0xc008627c]=0 CMF:HAL pktCmfHalConstruct: CMF:HAL pktDbgLvl[0xc008627c]=0 CMF:DRV pktCmfDrvConstruct: CMF:DRV pktDbgLvl[0xc008e5d4]=0 Broadcom Packet CMF (Experimental) Char Driver v0.1 Nov 1 2011 13:54:02 Registe red<232> CMF:PROTO pktCmfProtoConstruct: CMF:PROTO pktDbgLvl[0xc008e5a0]=0 Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Nov 1 2011 13:54:01 Loaded bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6368B2 Ethernet Network Device v0.1 Nov 1 2011 13:55:03 ETH Init: Ch:0 - 180 tx BDs at 0xa3961000 ETH Init: Ch:1 - 0 tx BDs at 0xa3ac0a80 ETH Init: Ch:0 - 400 rx BDs at 0xa3ac6000 ETH Init: Ch:1 - 0 rx BDs at 0xa3ac0980 Error: kerSysRegisterDyingGaspHandler: list head is null CMF:HW pktDbgLvl[0xc007f220]=0 CMF:HW pktCmfHwReset: Reset HW layer. Broadcom Packet CMF (Experimental) SWC RESET. BRCM Ext Switch: Tag <0:0x0:0> Port<0> Broadcom Packet CMF (Experimental) SWC INITIALIZED. CMF:FWD pktCmfFwdDevConstruct: CMF:FWD pktDbgLvl[0xc008e644]=0 Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Nov 1 2011 13:54 :02 Registered CMF Fwd Hnd DbgLvl <0xc008e670> = <0> CMF:FWD pktCmfFwdDevConstruct: CMF:FWD pktDbgLvl[0xc008e644]=0 Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Nov 1 2011 13:54 :02 Registered CMF Fwd Hnd DbgLvl <0xc008e670> = <0> Broadcom Packet CMF (Experimental) ENABLED. eth0: MAC Address: XX:XX:XX:XX:XX:XX eth1: MAC Address: XX:XX:XX:XX:XX:XX eth2: MAC Address: XX:XX:XX:XX:XX:XX eth3: MAC Address: XX:XX:XX:XX:XX:XX BCM63XX_USB USB Device not present insmod: cannot insert `/lib/modules/2.6.30/extra/bcm_usb.ko': Success (19): Succ ess PCI: Enabling device 0000:00:01.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:01.0 to 64 wl: passivemode=1 wl: napimode=0 wl: allocskbmode=1 wl:srom strapped wl:(srom strapped) probe/present=0 wl:srom not detected, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm43222_map.bin wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.100.123.0.cpe4.10L02.6 Error: kerSysRegisterDyingGaspHandler: list head is null IRQ 21/brcm_21: IRQF_DISABLED is not guaranteed on shared IRQs Broadcom 802.1Q VLAN Interface, v0.1 ===== Comtrend Release Version Q611-410JAZ-C02_R04 ===== Auto-negotiation enabled. Link is down device eth0 entered promiscuous mode ip_tables: (C) 2000-2006 Netfilter Core Team Auto-negotiation enabled. Link is down device eth1 entered promiscuous mode Auto-negotiation enabled. Link is down device eth2 entered promiscuous mode Auto-negotiation enabled. Link is down device eth3 entered promiscuous mode device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state WLmngr Daemon is running optarg=0 shmId=0 BcmAdsl_Initialize=0xC011AED0, g_pFnNotifyCallback=0xC014C184 wlevt is ready for new msg... Clocks for QPROC and AFE are being aligned with step through ... AFE is aligned, i = 065, PhaseValue = -150, PhaseCntl = 0x7FC00000 QPROC is aligned, i = 013, PhaseValue = 0050, PhaseCntl = 0x7FC0400D Clocks for QPROC and AFE are aligned with syn_status AFE = 0x78, QPROC = 0x78 AFE phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f pSdramPHY=0xA3FFFFF8, 0x669D6699 0x66996699 *** XfaceOffset: 0x5FF90 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xC5A48 => 0xFBEE8 *** AdslCoreSharedMemInit: shareMemAvailable=16624 AdslCoreHwReset: pLocSbSta=82ff0000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3FBB208 Error: kerSysRegisterDyingGaspHandler: list head is null XTM Init: 400 rx BDs at 0xa2fb2000 XTM Init: 16 rx BDs at 0xa2f9f180 Register interface ppp0.1 !! monitor task is initialized pid= 244 echo 005d0140 > /proc/switch Comtrend polling daemon is running upnp:error:22.867:process_smd_connection:474:cannot handle msg type 0x10000250 Switch MDK: num_switches = 1 Switch MDK: unit = 0; phy_pbmp = 0xf; config_pbmp = 0xf Switch MDK link poll thread: unit=0; phypbmp=0xf tr69c:error:24.439:sendInform:1330:ACS Connect failed with error "Could not reso lve host acs.jazztel.com". Retry session connection tr69c:error:24.440:retrySessionConnection:221:ACS connect failed, retryCount = 1 , backOffTime = 8000ms device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state br0: port 5(wl0) entering disabled state There is no Predefined DevicePin in CFE WPS Device PIN = 18836486 Setting SSID: "WLAN_69" Setting SSID: "wl0_Guest1" Setting SSID: "wl0_Guest2" Setting SSID: "wl0_Guest3" device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state UPnP daemon is ready to run acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0x2b0b tr69c:error:32.458:sendInform:1330:ACS Connect failed with error "Could not reso lve host acs.jazztel.com". Retry session connection tr69c:error:32.459:retrySessionConnection:221:ACS connect failed, retryCount = 2 , backOffTime = 18000ms device wds0.1 entered promiscuous mode br0: port 6(wds0.1) entering forwarding state br0: starting userspace STP failed, starting kernel STP tr69c:error:50.487:sendInform:1330:ACS Connect failed with error "Could not reso lve host acs.jazztel.com". Retry session connection tr69c:error:50.487:retrySessionConnection:221:ACS connect failed, retryCount = 3 , backOffTime = 22000ms BCM96368 Broadband Router Login:

[ 0.000000] Linux version 3.6.11 (noltari@skynet) (gcc version 4.6.4 20121210 (prerelease) (Linaro GCC 4.6-2012.12) ) #2 Wed Jan 9 17:10:21 CET 2013 [ 0.000000] Detected Broadcom 0x6368 CPU revision b2 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] registering 38 GPIOs [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.37-110.11 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350) [ 0.000000] board_bcm963xx: board name: 96368M-1541N [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 802a8db0, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] Memory: 60844k/65536k available (2260k kernel code, 4692k reserved, 400k data, 1072k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.028000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.032000] pid_max: default: 32768 minimum: 301 [ 0.036000] Mount-cache hash table entries: 512 [ 0.040000] NET: Registered protocol family 16 [ 0.048000] registering PCI controller with io_map_base unset [ 0.060000] bio: create slab at 0 [ 0.064000] PCI host bridge to bus 0000:00 [ 0.068000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.072000] pci_bus 0000:00: root bus resource [io 0x8000000-0x800ffff] [ 0.076000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.080000] pci_bus 0000:00: busn_res: [bus 00-ff] is inserted under domain [bus 00-ff] [ 0.080000] pci 0000:00:01.0: [14e4:a8d6] type 00 class 0x028000 [ 0.080000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00003fff] [ 0.092000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.092000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff] [ 0.096000] Switching to clocksource MIPS [ 0.104000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.108000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64 [ 0.132000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 [ 0.140000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x1E, vendor 0x4243) [ 0.140000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243) [ 0.140000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243) [ 0.196000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.204000] NET: Registered protocol family 2 [ 0.208000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.216000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.224000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.232000] TCP: reno registered [ 0.232000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.240000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.248000] NET: Registered protocol family 1 [ 0.252000] PCI: CLS 0 bytes, default 16 [ 2.052000] audit: initializing netlink socket (disabled) [ 2.060000] type=2000 audit(2.060:1): initialized [ 2.064000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.072000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 2.080000] msgmni has been set to 118 [ 2.084000] io scheduler noop registered [ 2.088000] io scheduler deadline registered (default) [ 2.096000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart [ 2.104000] console [ttyS0] enabled, bootconsole disabled [ 2.116000] bcm63xx-rng bcm63xx-rng: registered RNG driver [ 2.124000] physmap platform flash device: 08000000 at 18000000 [ 2.132000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 2.140000] Amd/Fujitsu Extended Query Table at 0x0040 [ 2.148000] Amd/Fujitsu Extended Query version 1.3. [ 2.152000] number of CFI chips: 1 [ 2.156000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368M-1541N [ 2.164000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000 [ 2.172000] bcm63xxpart: Partition 1 is rootfs offset 20100 and length 4e9000 [ 2.180000] bcm63xxpart: Partition 2 is kernel offset 509100 and length 111198 [ 2.184000] bcm63xxpart: Partition 3 is nvram offset 1fe0000 and length 20000 [ 2.192000] bcm63xxpart: Partition 4 is linux offset 20000 and length 1fc0000 [ 2.200000] bcm63xxpart: Spare partition is offset 620000 and length 19c0000 [ 2.208000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0 [ 2.216000] Creating 5 MTD partitions on "physmap-flash.0": [ 2.220000] 0x000000000000-0x000000020000 : "CFE" [ 2.228000] 0x000000020100-0x000000509100 : "rootfs" [ 2.232000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 2.248000] mtd: partition "rootfs" set to be root filesystem [ 2.252000] split_squashfs: no squashfs found in "physmap-flash.0" [ 2.260000] 0x000000509100-0x00000061a298 : "kernel" [ 2.264000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 2.280000] 0x000001fe0000-0x000002000000 : "nvram" [ 2.288000] 0x000000020000-0x000001fe0000 : "linux" [ 2.332000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 2.340000] TCP: cubic registered [ 2.344000] NET: Registered protocol family 17 [ 2.348000] 8021q: 802.1Q VLAN Support v1.8 [ 2.368000] Freeing unused kernel memory: 1072k freed [ 3.204000] roboswitch: Probing device 'eth0' [ 3.212000] bcm63xx_enet: could not find a used port with phy_id 0, assuming phy is external [ 3.224000] roboswitch: Failed to enable switch [ 3.228000] roboswitch: Probing device 'eth1' [ 3.232000] roboswitch: No such device [ 3.236000] roboswitch: Probing device 'eth2' [ 3.240000] roboswitch: No such device [ 3.244000] roboswitch: Probing device 'eth3' [ 3.248000] roboswitch: No such device [ 9.008000] There is already a switch registered on the device 'eth0' [ 9.016000] roboswitch: Probing device 'eth1' [ 9.020000] roboswitch: No such device [ 9.024000] roboswitch: Probing device 'eth2' [ 9.028000] roboswitch: No such device [ 9.032000] roboswitch: Probing device 'eth3' [ 9.036000] roboswitch: No such device [ 9.068000] Button Hotplug driver version 0.4.1 [ 9.108000] PPP generic driver version 2.4.2 [ 9.176000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 9.328000] NET: Registered protocol family 24 [ 9.356000] nf_conntrack version 0.5.0 (967 buckets, 3868 max) [ 9.624000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) v0.1.2 [ 12.628000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port1, 100Mbps, full-duplex