User Tools

Site Tools


toh:cubietech:cubieboard2

Cubieboard2

For further Allwinner-based boards, please refer to soc.allwinner.sunxi

Hardware highlights

Model Ports
Cubieboard2 4GB NAND, μSD, 2x USB2, 10/100 Mbps ethernet, SATA, UEXT, HDMI, audio

Serial

You can use your usual serial levelshifter. Pinout is:

[ μSD ] [ HDMI ]

[ USB ]   TX  RX  GND
          o  o  o  o



[ ethernet ]

Status

Installation process

Please refer to soc.allwinner.sunxi.

dmesg

U-Boot SPL 2013.10-rc2 (Feb 27 2014 - 22:16:14)
Board: Cubieboard2
DRAM: 1024 MiB
CPU: 960000000Hz, AXI/AHB/APB: 3/2/2
spl: not an uImage at 1600


U-Boot 2013.10-rc2 (Feb 27 2014 - 22:16:14) Allwinner Technology

CPU:   Allwinner A20 (SUN7I)
Board: Cubieboard2
I2C:   ready
DRAM:  1 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   emac
Hit any key to stop autoboot:  3  2  1  0 
reading uEnv.txt
240 bytes read in 2 ms (117.2 KiB/s)
Loaded environment from uEnv.txt
Running uenvcmd ...
reading uImage
2371480 bytes read in 191 ms (11.8 MiB/s)
reading dtb
16105 bytes read in 3 ms (5.1 MiB/s)
## Booting kernel from Legacy Image at 46000000 ...
   Image Name:   ARM OpenWrt Linux-3.13.2
   Created:      2014-02-27  14:18:25 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2371416 Bytes = 2.3 MiB
   Load Address: 40008000
   Entry Point:  40008000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 49000000
   Booting using the fdt blob at 0x49000000
   Loading Kernel Image ... OK
   Using Device Tree in place at 49000000, end 49006ee8

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.13.2 (yousong@debian) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r39135) ) #2 SMP PREEMPT Thu Feb 27 22:18:09 CST 2014
[    0.000000] CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Cubietech Cubieboard2
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] PERCPU: Embedded 7 pages/cpu @c0d1f000 s7040 r8192 d13440 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 260624
[    0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1034272K/1048576K available (3287K kernel code, 152K rwdata, 932K rodata, 178K init, 604K bss, 14304K reserved, 270336K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0426f2c   (4220 kB)
[    0.000000]       .init : 0xc0427000 - 0xc0453b80   ( 179 kB)
[    0.000000]       .data : 0xc0454000 - 0xc047a2f8   ( 153 kB)
[    0.000000]        .bss : 0xc047a2f8 - 0xc051159c   ( 605 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
[    0.000000] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 26843545593ns
[    0.000000] Console: colour dummy device 80x30
[    0.000196] Calibrating delay loop... 1915.28 BogoMIPS (lpj=9576448)
[    0.059908] pid_max: default: 32768 minimum: 301
[    0.060088] Mount-cache hash table entries: 512
[    0.060872] CPU: Testing write buffer coherency: ok
[    0.061183] /cpus/cpu@0 missing clock-frequency property
[    0.061201] /cpus/cpu@1 missing clock-frequency property
[    0.061214] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.061247] Setting up static identity map for 0x40011718 - 0x4001174c
[    0.120358] CPU1: failed to boot: -38
[    0.120383] Brought up 1 CPUs
[    0.120390] SMP: Total of 1 processors activated.
[    0.120396] CPU: All CPU(s) started in SVC mode.
[    0.125075] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4
[    0.125337] pinctrl core: initialized pinctrl subsystem
[    0.125698] regulator-dummy: no parameters
[    0.126003] NET: Registered protocol family 16
[    0.126303] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.132565] bio: create slab <bio-0> at 0
[    0.133075] reg-fixed-voltage ahci-5v.4: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@0, deferring probe
[    0.133103] platform ahci-5v.4: Driver reg-fixed-voltage requests probe deferral
[    0.133130] reg-fixed-voltage usb1-vbus.5: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
[    0.133144] platform usb1-vbus.5: Driver reg-fixed-voltage requests probe deferral
[    0.133168] reg-fixed-voltage usb2-vbus.6: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
[    0.133181] platform usb2-vbus.6: Driver reg-fixed-voltage requests probe deferral
[    0.133555] SCSI subsystem initialized
[    0.133984] usbcore: registered new interface driver usbfs
[    0.134034] usbcore: registered new interface driver hub
[    0.134148] usbcore: registered new device driver usb
[    0.134273] pps_core: LinuxPPS API ver. 1 registered
[    0.134281] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.134307] PTP clock support registered
[    0.135049] Switched to clocksource timer
[    0.140170] Clockevents: could not switch to one-shot mode: dummy_timer is not functional.
[    0.140193] Could not switch to high resolution mode on CPU 0
[    0.140456] NET: Registered protocol family 2
[    0.141209] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.141291] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.141412] TCP: Hash tables configured (established 8192 bind 8192)
[    0.141495] TCP: reno registered
[    0.141510] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.141568] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.141907] NET: Registered protocol family 1
[    0.143081] audit: initializing netlink socket (disabled)
[    0.143127] type=2000 audit(0.130:1): initialized
[    0.143806] bounce pool size: 64 pages
[    0.149894] VFS: Disk quotas dquot_6.5.2
[    0.150265] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.151830] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.151860] msgmni has been set to 1492
[    0.153294] io scheduler noop registered
[    0.153308] io scheduler deadline registered
[    0.153344] io scheduler cfq registered (default)
[    0.155523] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[    0.188217] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[    0.210210] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A
[    0.731380] console [ttyS0] enabled
[    0.735855]  Ring mode enabled
[    0.738917]  No HW DMA feature register supported
[    0.743481]  Normal descriptors
[    0.746804]  Wake-Up On Lan supported
[    0.754164] libphy: stmmac: probed
[    0.757575] eth0: PHY ID 00008201 at 1 IRQ 0 (stmmac-0:01) active
[    0.763857] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.770421] sunxi-ehci: Allwinner sunXi EHCI driver
[    0.775448] platform 1c14000.ehci0: Driver sunxi-ehci requests probe deferral
[    0.782676] platform 1c1c000.ehci1: Driver sunxi-ehci requests probe deferral
[    0.789905] usbcore: registered new interface driver usb-storage
[    0.796140] mousedev: PS/2 mouse device common for all mice
[    0.802540] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    0.811139] sunxi-mci 1c0f000.mmc: base:0xf00b2000 irq:64
[    0.817333] TCP: cubic registered
[    0.820735] Initializing XFRM netlink socket
[    0.825026] NET: Registered protocol family 17
[    0.829559] 8021q: 802.1Q VLAN Support v1.8
[    0.834045] Registering SWP/SWPB emulation handler
[    0.839181] registered taskstats version 1
[    0.843893] ahci-5v: 5000 mV 
[    0.847174] usb1-vbus: 5000 mV 
[    0.850687] usb2-vbus: 5000 mV 
[    0.854091] sunxi-ehci 1c14000.ehci0: EHCI Host Controller
[    0.859596] sunxi-ehci 1c14000.ehci0: new USB bus registered, assigned bus number 1
[    0.867393] sunxi-ehci 1c14000.ehci0: irq 71, io mem 0x01c14000
[    0.890154] sunxi-ehci 1c14000.ehci0: USB 2.0 started, EHCI 1.00
[    0.896372] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.903200] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.910428] usb usb1: Product: EHCI Host Controller
[    0.915302] usb usb1: Manufacturer: Linux 3.13.2 ehci_hcd
[    0.920726] usb usb1: SerialNumber: 1c14000.ehci0
[    0.925895] hub 1-0:1.0: USB hub found
[    0.929725] hub 1-0:1.0: 1 port detected
[    0.934181] sunxi-ehci 1c1c000.ehci1: EHCI Host Controller
[    0.939684] sunxi-ehci 1c1c000.ehci1: new USB bus registered, assigned bus number 2
[    0.947475] sunxi-ehci 1c1c000.ehci1: irq 72, io mem 0x01c1c000
[    0.970150] sunxi-ehci 1c1c000.ehci1: USB 2.0 started, EHCI 1.00
[    0.976310] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    0.983109] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.991356] usb usb2: Product: EHCI Host Controller
[    0.997260] usb usb2: Manufacturer: Linux 3.13.2 ehci_hcd
[    1.002668] usb usb2: SerialNumber: 1c1c000.ehci1
[    1.007795] hub 2-0:1.0: USB hub found
[    1.011603] hub 2-0:1.0: 1 port detected
[    1.015844] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[    1.022932] Waiting for root device /dev/mmcblk0p2...
[    1.061974] sunxi-mci 1c0f000.mmc: smc 0 err, cmd 8, RTO !!
[    1.211954] sunxi-mci 1c0f000.mmc: smc 0 err, cmd 8, RTO !!
[    1.235781] mmc0: SD Status: Invalid Allocation Unit size.
[    1.450146] mmc0: new high speed SD card at address b368
[    1.455856] isa bounce pool size: 16 pages
[    1.460086] mmcblk0: mmc0:b368 SD256 244 MiB 
[    1.465741]  mmcblk0: p1 p2
[    1.571049] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[    1.579767] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[    1.593724] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    1.601966] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.608971] Freeing unused kernel memory: 176K (c0427000 - c0453000)
procd: Console is alive
procd: - watchdog -
procd: - preinit -
probing /dev/mmcblk0 for uboot env data
[    1.892334] sunxi-ahci 1c18000.ahci: controller can't do PMP, turning off CAP_PMP
[    1.903236] sunxi-ahci 1c18000.ahci: forcing PORTS_IMPL to 0x1
[    1.909092] sunxi-ahci 1c18000.ahci: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl sunxi mode
Detected generic sunxi // generic sunxi[    1.939684] sunxi-ahci 1c18000.ahci: flags: ncq sntf pm led clo only pio slum part ccc 

[    1.957231] scsi0 : sunxi_ahci
[    1.963574] random: mktemp urandom read with 19 bits of entropy available
[    1.971066] ata1: SATA max UDMA/133 irq 88
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    2.320165] ata1: SATA link down (SStatus 0 SControl 300)
mount_root: mounting /dev/root
[    5.099990] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[    7.109435] NET: Registered protocol family 10
[    7.130439] nf_conntrack version 0.5.0 (16163 buckets, 64652 max)
[    7.160431] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    7.202011] sunxi-rtc 1c20d00.rtc: rtc core: registered rtc-sunxi as rtc0
[    7.208806] sunxi-rtc 1c20d00.rtc: RTC enabled
[    7.232073] ip_tables: (C) 2000-2006 Netfilter Core Team
[    7.372898] xt_time: kernel timezone is -0000
[    7.383574] PPP generic driver version 2.4.2
[    7.399322] NET: Registered protocol family 24
[    8.584265] random: nonblocking pool is initialized
procd: - init complete -



BusyBox v1.19.4 (2014-02-27 21:24:43 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

  _______                     ________        __
 |       |.-----.-----.-----.|  |  |  |.----.|  |_
 |   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
 |_______||   __|_____|__|__||________||__|  |____|
          |__| W I R E L E S S   F R E E D O M
 -----------------------------------------------------
 BARRIER BREAKER (Bleeding Edge, r39756)
 -----------------------------------------------------
  * 1/2 oz Galliano         Pour all ingredients into
  * 4 oz cold Coffee        an irish coffee mug filled
  * 1 1/2 oz Dark Rum       with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
 -----------------------------------------------------
root@OpenWrt:/# 

Tags

toh/cubietech/cubieboard2.txt · Last modified: 2014/05/14 10:17 by lorema