Differences
This shows you the differences between two versions of the page.
| — |
toh:d-link:dap-1350 [2012/12/24 04:42] (current) brynet created |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| + | ====== D-Link DAP-1350 ====== | ||
| + | FIXME | ||
| + | |||
| + | ===== Hardware Highlights ===== | ||
| + | ^ CPU ^ Ram ^ Flash ^ Network ^ USB ^ Serial ^ JTag ^ | ||
| + | | RaLink RT288x/RT305x WiSoC@384 MHz | 32MiB | 8MiB | 1 x10/100E | Yes | Yes, internal TTL solder pads | ? | | ||
| + | |||
| + | ===== Installing of OpenWrt ===== | ||
| + | The build script is currently not run on trunk so no official binary is available. | ||
| + | |||
| + | Build from trunk or 'attitude_adjustment' branch as the latest release branch 'backfire' doesn't have the build target files. For more information about building see the [[doc:howto:build|build documentation]]. | ||
| + | |||
| + | <code> | ||
| + | svn co svn://svn.openwrt.org/openwrt/trunk/ | ||
| + | # Build configuration. From 'make menuconfig'; Target system: Ralink RT288x/RT3xxx, Subtarget: RT305x based boards | ||
| + | echo CONFIG_TARGET_ramips=y >.config | ||
| + | echo CONFIG_TARGET_ramips_rt305x=y >>.config | ||
| + | echo CONFIG_TARGET_ramips_rt305x_Default=y >>.config | ||
| + | make | ||
| + | </code> | ||
| + | |||
| + | When the build process is done (yes, this could take several hours), flash the appropriate generated (openwrt-*-squashfs-factory.bin) file from web interface or from recovery mode (turn off; hold reset; turn on; go to http://dlinkap or http://192.168.0.50). Use the file matching your router model (IE: openwrt-ramips-rt305x-dap-1350-squashfs-factory.bin for DAP-1350) | ||
| + | |||
| + | ==== Upgrading OpenWrt ==== | ||
| + | If you have already installed a version of openwrt and you wish to upgrade your installation | ||
| + | |||
| + | * uploaded the new firmware from the LAN with 'scp openwrt-*-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/'. | ||
| + | * flash it on the router with 'sysupgrade /tmp/openwrt-*-squashfs-sysupgrade.bin'. | ||
| + | |||
| + | FIXME | ||
| + | |||
| + | ===== Hardware ===== | ||
| + | ==== Hardware Details ==== | ||
| + | === Details for DAP-1350 === | ||
| + | |||
| + | | **[[wp>Instruction set|Architecture]]:** | [[wp>MIPS architecture|MIPS]] | | ||
| + | | **Status:** | trunk (>R33411) | | ||
| + | | **Vendor:** | [[wp>Ralink]] | | ||
| + | | **[[doc:techref:Bootloader]]:** | [[doc:techref:bootloader:uboot|U-Boot]] | | ||
| + | | **[[doc:hardware:soc|System-On-Chip]]:** | [[http://www.tracermcc.ru/foto/bender/RT3050_5x_V2.0_081408_0902.pdf|RT288x/RT305x WiSoC]] | | ||
| + | | **[[doc:hardware:cpu|CPU]]/Speed** | MIPS24KEc@384 Mhz w/ 16KB I cache/16KB D cache | | ||
| + | | **Flash-Chip:** | [[http://www.futureelectronics.com/en/technologies/semiconductors/memory/flash/nor/Pages/2303212-MX29LV640EBTI-70G.aspx|Macronix MX29LV640EBTI-70G]] | | ||
| + | | **Flash size:** | 8192 KiB | | ||
| + | | **RAM:** | [[http://www.esmt.com.tw/DB/manager/upload/M12L128168A.pdf|ESMT M12L128168A-7T]] x 2| | ||
| + | | **RAM:** | 32 MiB | | ||
| + | | **Wireless:** | [[http://www.tracermcc.ru/foto/bender/RT3050_5x_V2.0_081408_0902.pdf|Ralink RT3052F]] 2.4ghz 802.11bgn | | ||
| + | | **Ethernet:** | integrated 1 x10/100E w/ vlan support [[doc:techref:swconfig]] | | ||
| + | | **Internet:** | no | | ||
| + | | **USB:** | yes | | ||
| + | | **Power:** | external 5V 2.5A | | ||
| + | | **[[doc:hardware:port.serial|Serial]]:** | [[#Serial|Yes]] | | ||
| + | |||
| + | ==The information written on the main Ralink chip== | ||
| + | |||
| + | FIXME | ||
| + | |||
| + | ==The information written on the WiFi Ralink chip== | ||
| + | |||
| + | FIXME | ||
| + | |||
| + | ==The information written on the PSC Ram chip== | ||
| + | |||
| + | FIXME | ||
| + | |||
| + | ==The information on the Flash chip== | ||
| + | |||
| + | FIXME | ||
| + | |||
| + | ==== Serial ==== | ||
| + | |||
| + | FIXME | ||
| + | |||
| + | ===== Basic configuration ===== | ||
| + | -> [[doc:howto:basic.config|Basic configuration]] After flashing, proceed with this.\\ | ||
| + | Set up your Internet connection, configure wireless etc. | ||
| + | |||
| + | ===== Device specific configuration ===== | ||
| + | ==== Wireless LED ==== | ||
| + | On a basic installation the wireless LED does not blink if data is transmitted and/or received. To fix this simply append this block to /etc/config/system: | ||
| + | <code> | ||
| + | option 'led' 'wlan_led' | ||
| + | option 'name' 'WLAN' | ||
| + | option 'sysfs' 'rt2800pci-phy0::radio' | ||
| + | option 'trigger' 'netdev' | ||
| + | option 'dev' 'wlan0' | ||
| + | option 'mode' 'link tx rx' | ||
| + | </code> | ||
| + | |||
| + | More detailed information about LEDs can be found [[doc:uci:system#leds|here]]. | ||
| + | |||
| + | ===== Failsafe mode ===== | ||
| + | -> [[doc:howto:generic.failsafe]] | ||
| + | |||
| + | If you forgot your password, broke one of the startup scripts, firewalled yourself out, or corrupted the JFFS2 partition, you can get back in by using OpenWrt's failsafe mode. | ||
| + | |||
| + | ==== Boot into failsafe mode ==== | ||
| + | * Unplug the router's power cord. | ||
| + | * Connect the router's LAN1 port directly to your PC. | ||
| + | * Configure your PC with a static IP address between 192.168.1.2 and 192.168.1.254. Eg. 192.168.1.2 (gateway and DNS is not required). | ||
| + | * Plug the power on and wait for the DMZ LED to light up. | ||
| + | * While the DMZ LED is on immediately press any button (Reset and Secure Easy Setup will work) a few times . | ||
| + | * If done right the DMZ LED will quickly flash 3 times every second. | ||
| + | * You should be able to telnet to the router at 192.168.1.1 now (no username and password) | ||
| + | |||
| + | ==== What to do in failsafe mode? ==== | ||
| + | **NOTE:** The root file system in failsafe mode is the SquashFS partition mounted in readonly mode. To switch to the normal writable root file system run mount_root and make any changes. Run mount_root now. | ||
| + | |||
| + | - Forgot/lost your password and you like to set a new one | ||
| + | ''passwd'' | ||
| + | - Forgot the routers IP address | ||
| + | ''uci get network.lan.ipaddr'' | ||
| + | - You accidentally run 'ipkg upgrade' or filled up the flash by installing large packages (clean the JFFS2 partition and start over) | ||
| + | ''mtd -r erase rootfs_data'' | ||
| + | If you are done with failsafe mode power cycle the router and boot in normal mode. | ||
| + | |||
| + | ===== Other Info ===== | ||
| + | ==== Default Router Settings ==== | ||
| + | === Model DAP-1350 === | ||
| + | |||
| + | * IP : 192.168.0.50 | ||
| + | * Username : "admin" | ||
| + | * Password : "" (leave field blank) | ||
| + | * Polarity : **⊖―כּ―⊕** | ||
| + | * Input : 5V / 2.5A | ||
| + | * FCC ID : KA2AP1350A1 | ||
| + | |||
| + | ===== Tags ===== | ||
| + | {{tag>FastEthernet 1Port integrated 1Radio 802.11bgn 1Ant DetachableAntenna 32RAM 8Flash MIPS 24KE macronix }} | ||
| + | |||
| + | ==== If all else fails ==== | ||
| + | The DAP-1350 has a special D-Link firmware mode that runs a HTTP server on 192.168.0.50 for uploading new firmware. If you get locked out and/or brick your device, you can get into this mode by holding down the reset button for 30-45 seconds while booting the device. Note that the IP of the server it runs is 192.168.*0*.50. | ||
toh/d-link/dap-1350.txt · Last modified: 2012/12/24 04:42 by brynet