You are here: OpenWrt Wiki » Table of Hardware » D-Link » D-Link DIR-615

Differences

This shows you the differences between two versions of the page.

--- toh:d-link:dir-615 [2012/12/20 01:03]
ka_fe
+++ toh:d-link:dir-615 [2013/05/11 01:31] (current)
orenr
@@ Line 2: / Line 2: @@
 ===== Supported Versions =====
 ^ Revision ^ Version Supported ^ Model Specific Notes ^
-| C1, C2 | Backfire | Full support, eth/wireless/leds/buttons ok  |
+| C1, C2 | Attitude Adjustment RC1 | Full support, eth/wireless/leds/buttons ok  |
 | D1/D2 | trunk | Partly working - problems with ethernet. Requires manual custom build. |
-| D3/D4 | trunk | Mostly working. Requires manual build. (Works with DIR-600/B2 firmware)* |
+| D3/D4 | trunk | Working with AA (12.09) [[https://forum.openwrt.org/viewtopic.php?id=35184|Forum]]  |
 | E1 - E4 | Backfire | (Works with DIR-600 rev. A1 firmware)*, LEDs should work since [[https://dev.openwrt.org/changeset/29973/trunk|R29973]], support for E4 merged with [[toh:d-link:DIR-600]] A1 in [[https://dev.openwrt.org/changeset/29976/trunk|R29976]]  |
 | H1 | trunk | Partly working - Requires manual custom build with network configuration |
 **NOTE:** ONLY revision C1 and C2 are fully supported yet.
-*You might have to change the magic number at the end of the OpenWRT firmware to the one used by the stock DIR-615 firmware to get it to upload.
+*You might have to change the magic number at the end of the OpenWRT firmware to the one used by the stock DIR-615 firmware to get it to upload.  \\
+Frys FR-300RTR is the same as E1 [[https://forum.openwrt.org/viewtopic.php?pid=131673#p131673|Forum]] \\
-Frys FR-300RTR is the same as E1 [[https://forum.openwrt.org/viewtopic.php?pid=131673#p131673|Forum]]
+* April 2013 - **Version E4 is supported and known to work with attitude adjustment 12.09** [[http://downloads.openwrt.org/attitude_adjustment/12.09/ar71xx/generic/openwrt-ar71xx-generic-dir-615-e4-squashfs-factory.bin|(link to flash file))]] , see installation instruction below \\
 ===== Unsupported Versions =====
@@ Line 23: / Line 23: @@
 FIXME add revisions
 ^ Revisions ^ CPU ^ Ram ^ Flash ^ Network ^ Gigabit ^ USB ^ Serial ^ JTag ^
-|A1    | Marvell | 32MB | 8MB | 4x1 | No | No | Yes | Yes |
+|A1      | Marvell | 32MB | 8MB | 4x1 | No | No | Yes | Yes |
-|B2    | Ubicom  | 8MB  | 2MB | 4x1 | No | No   | Yes | Yes |
+|B2      | Ubicom  | 8MB  | 2MB | 4x1 | No | No   | Yes | Yes |
-|C1, C2| Atheros | 32MB | 4MB | 4x1 | No | Yes* | Yes | No  |
+|C1, C2  | Atheros | 32MB | 4MB | 4x1 | No | Yes* | Yes | No  |
-|D1 - D5| Ralink | 32MB | 4MB | 4x1 | No | No   | Yes | No  |
+|D1 - D5 | Ralink | 32MB | 4MB | 4x1 | No | No   | Yes | No  |
-|E1, E2| Atheros | 32MB | 4MB | 4x1 | No | Yes* | Yes | Yes |
+|E1, E2  | Atheros | 32MB | 4MB | 4x1 | No | Yes* | Yes | Yes |
-|E3, E4| Atheros | 32MB | 4MB | 4x1 | No | Yes* | Yes | Yes |
+|E3,E4,E5| Atheros | 32MB | 4MB | 4x1 | No | Yes* | Yes | Yes |
-|F1, F2| Realtek | 16MB | 2MB | 4x1 | No | No   | Yes | Yes |
+|F1, F2  | Realtek | 16MB | 2MB | 4x1 | No | No   | Yes | Yes |
-|G1    | Ralink  | 32MB | 8MB | 4x1 | No | No   | Yes | ?   |
+|G1      | Ralink  | 32MB | 8MB | 4x1 | No | No   | Yes | ?   |
-|H1    | Ralink  | 32MB | 4MB | 4x1 | No  | No   | Yes | Yes |
+|H1      | Ralink  | 32MB | 4MB | 4x1 | No  | No   | Yes | Yes |
-|I1 | Atheros | 32MB | ? | ? | no | no | ? | ? |
+|I1      | Atheros | 32MB | ? | ? | no | no | ? | ? |
-|I2 |  |  |  |  |  |  |  |  |
+|I2      |  |  |  |  |  |  |  |  |
-|J1 | Realtek | 16MB | 2MB  |  4x1 |  No |  No |  Yes |  Yes |
+|J1      | Realtek | 16MB | 2MB  | 4x1 |  No |  No |  Yes |  Yes |
-|K1 |  |  |  |  |  |  |  |  |
+|K1      | Broadcom | 32MB | 4MB | 4x1 |  No |  No |  No  |  No  |
 ===== Installation =====
-==== Rev. C1 ====
+==== Rev. C1 and E4 ====
 Installation is fairly straight forward for this router, you will need to access the D-Link recovery console with the steps below.
-  - As per the note at http://www.dd-wrt.com/wiki/index.php/DIR-615C , "If your dlink 615 C1 is at f/w 3.12 or 3.11 you may have to revert it to 3.10".  The older firmware is available from D-Link: http://www.dlink.com/products/?tab=3&pid=DIR-615&rev=DIR-615_revC
+  - As per the note at http://www.dd-wrt.com/wiki/index.php/DIR-615C , "If your dlink 615 C1 is at f/w 3.12 or 3.11 you may have to revert it to 3.10".  The older firmware is available from [[http://www.dlink.com/us/en/support/product/dir-615-wireless-n-300-router?revision=us_revc|D-Link support]].
   - Set a static IP on your PC to '192.168.0.2'.
-  - Press and hold the reset button until the power LED starts blinking orange (usually takes ~45 seconds). Or, hold down the reset button while powering on the router, this is much quicker and only takes 5-10 seconds.
+  - Press and hold the reset button until the power LED starts blinking orange (usually takes ~45 seconds). Or, hold down the reset button while powering on the router, this is much quicker and only takes 5-15 seconds.
-  - Go to 'http://192.168.0.1' from your PC web browser. (Note: most modern browsers don't work, see below)
+  - Go to 'http://192.168.0.1' from your PC web browser. (Note: most modern browsers don't work, see below, Firefox 13 portable version is known to work)
   - "Browse" and select the OpenWrt firmware (e.g. 'openwrt-ar71xx-dir-615-c1-squashfs-factory.bin').
   - Let router flash the image, don't worry if it reboots before it reaches 100%. If the page loads forever or times out, your browser is unsupported. See below.
@@ Line 57: / Line 57: @@
 Internet Explorer 7 on Windows is known to work, as well as Firefox 13.0.1 on GNU/Linux, but problems have been reported with newer versions and most other browsers on GNU/Linux.  Older versions of Firefox (4.x and below) are known to have problems, several people have been more successful with newer versions. Alternatively, you can use the ''curl'' command-line HTTP client like so:
   curl -0vF files=@openwrt-ar71xx-dir-615-c1-squashfs-factory.bin http://192.168.0.1/cgi/index
 There seems to be some compatibility issues with the firmware update system network stack and at least a Linux 3.5.3 kernel and curl 7.27.0. Even forcing ''curl'' down to HTTP/1.0 resulted in a hang. One known working configuration is NetBSD 5.1.2 with curl 7.26.0.
+***A use of Firefox 13 portable edition (on windows 7) was verified as successful.
+**
 ==== Rev. D1-D4 ====
@@ Line 67: / Line 70: @@
 | FIXME: D1/D2 build instructions |
+The DIR-615D maps to DIR-300b1 therefore there is no dedicated target for 615-D.
+D2 can be flashed with Attitude Adjustment - RC1: openwrt-ramips-rt305x-dir-615-d-squashfs-factory.bin
+Problems when flashing with AA RC1 firmware:
+  - ethernet only works when trying to connect over 10baseT/UTP (10mbit/sec)
+  - wireless needs workaround
+**Wireless**:
+It is fixed in the recent Attitude Adjustment branch and works out of box. However, if you are using precompiled AA RC1 you will need a workaround: https://dev.openwrt.org/ticket/12636
+**Ethernet**:
+The only way to get this fully working is to recompile using old ramips ethernet drivers (from revision: 24328)
+To do this:
+  - get the desired branch/trunk
+  - navigate to target/linux/ramips/files/drivers/net/ethernet/ramips
+  - remove all *.c and *.h files
+  - copy into this folder the 3 files from https://dev.openwrt.org/browser/trunk/target/linux/ramips/files/drivers/net?rev=24328
+  - rename ramips.c to remips_main.c
+  - continue with configuration/compilation as normal
+This has been tested and the router works flawlessly.
 | FIXME: D3/D4 build instructions |
+Updated D4 install instructions (AArc2) are here: https://forum.openwrt.org/viewtopic.php?id=35184
 | FIXME: The DIR-825 has a better description: [[toh/d-link/dir-825#installation]]. |
@@ Line 90: / Line 117: @@
 Now you should be able to telnet to DIR-615_H1
-| FIXME: H1 build instructions |
+=== Rev. H1 Build Instruction ===
+This documentation refers to current trunk of 03.04.2013.
+Instead of using the above procedure, you can build the image following the next steps. It will create a working image with dhcp on wan and fixed ip 192.168.0.1 on lan.
+ - Download current trunk. I've downloaded it from git mirror:
+<code>
+git clone git://nbd.name/openwrt.git
+</code>
+ - Add the file "target/linux/ramips/rt305x/profiles/d-link.mk" with content (ref:[[https://forum.openwrt.org/viewtopic.php?id=40623|DIR-615 H1 current sources]]):
+<code>
+#
+# Copyright (C) 2012 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+define Profile/DIR615H1
+    NAME:=DIR-615 H1
+    PACKAGES:=\
+         kmod-usb-core kmod-usb-ohci \
+         kmod-usb2 kmod-ledtrig-usbdev \
+         usb-modeswitch usb-modeswitch-data \
+         kmod-usb-serial-option
+endef
+define Profile/DIR615H1/Description
+    Package set for DIR-615 H1
+endef
+$(eval $(call Profile,DIR615H1))
+</code>
+ - edit file "target/linux/ramips/base-files.mk", remove the line :
+<code>
+    rm -f $(1)/etc/config/network
+</code>
+ - Edit the file "package/base-files/files/etc/config/network" with the settings you want. For example:
+<code>
+# Copyright (C) 2006 OpenWrt.org
+config interface 'loopback'
+        option ifname 'lo'
+        option proto 'static'
+        option ipaddr '127.0.0.1'
+        option netmask '255.0.0.0'
+config interface 'lan'
+        option ifname 'eth0.1'
+        option type 'bridge'
+        option proto 'static'
+        option ipaddr '192.168.0.1'
+        option netmask '255.255.255.0'
+config interface 'wan'
+        option ifname 'eth0.2'
+        option hostname 'DIR-615-H1'
+        option proto    'dhcp'
+config switch
+        option name rt305x
+        option reset 1
+        option enable_vlan 1
+config switch_vlan
+        option device rt305x
+        option vlan 1
+        option ports '0 1 2 3 6t'
+config switch_vlan
+        option device rt305x
+        option vlan 2
+        option ports '4 6t'
+</code>
+ - In case you have already build something make a dirclean
+<code>
+make dirclean
+</code>
+ - Configure the image:
+<code>
+make menuconfig
+</code>
+<code>
+Target System (Ralink RT288x/RT3xxx)
+Subtarget (RT305x based boards)
+Target Profile (DIR-615 H1)
+</code>
+ - Build the image:
+<code>
+make -j 5
+</code>
 ==== Upgrading OpenWrt ====
@@ Line 212: / Line 328: @@
 | **JTAG:** [[:toh/d-link/dir-615#JTAG|Yes]] |
-Revision E3/E4:
+Revision E3/E4/E5:
 | **Architecture:** MIPS |
@@ Line 291: / Line 407: @@
 | **Serial:** Yes |
 | **JTAG:** Yes |
+Revision K1:
+| **Architecture:** ? |
+| **Bootloader:** ? |
+| **System-On-Chip:**  Broadcom BCM5357C0 |
+| **CPU Speed:** ? |
+| **Flash-Chip:** Macronix MX25L3206EMI-12G |
+| **Flash size:** 4MB |
+| **RAM-Chip:** Winbond W9425G6JH-5 |
+| **RAM size:** 32 MiB (2M x 16bit x 4 banks) |
+| **Wireless:** Broadcom BCM5357C0 |
+| **Ethernet:** SoC integrated |
+| **USB:** No |
+| **Serial:** ? |
+| **JTAG:** ? |
 FIXME More info, please!
@@ Line 302: / Line 434: @@
 | D3 | [[:toh/d-link/dir-615/d3-photos/start|toh/d-link/dir-615/d3-photos/start]] | Wireless, cpu are unshielded, revD3E |
 | D4 | [[:toh/d-link/dir-615/d4-photos/start|toh/d-link/dir-615/d4-photos/start]] | Wireless, cpu are unshielded |
-| E3/E4 | [[:toh/d-link/dir-615/e4-photos/start|toh/d-link/dir-615/e4-photos/start]] | Wireless, cpu and memory are unshielded on this photo |
+|E3/E4/E5 | [[:toh/d-link/dir-615/e4-photos/start|toh/d-link/dir-615/e4-photos/start]] | Wireless, cpu and memory are unshielded on this photo |
 | F1/F2 | [[:toh/d-link/dir-615/f1-photos/start|toh/d-link/dir-615/f1-photos/start]] | This is rev.F1/F2 device photo |
 | H1    | [[:toh/d-link/dir-615/h1-photos/start|toh/d-link/dir-615/h1-photos/start]] | Shield removed |
@@ Line 383: / Line 515: @@
   * If done right the DMZ LED will quickly flash 3 times every second.
   * You should be able to telnet to the router at 192.168.1.1 now (no username and password)
+FIXME What is the DMZ LED? It's not mentioned anywhere else in this article.
 ==== What to do in failsafe mode? ====

toh/d-link/dir-615.1355961795.txt.bz2 · Last modified: 2012/12/20 01:03 by ka_fe

OpenWrt

Wiki Search

Actions

Donate

Translations

Differences