User Tools

Site Tools


toh:d-link:dir-835

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Previous revision
toh:d-link:dir-835 [2013/02/18 18:33]
toh:d-link:dir-835 [2014/10/03 04:21] (current)
mandrawes
Line 1: Line 1:
 ====== D-Link DIR-835 ====== ====== D-Link DIR-835 ======
-DIR-835 Rev A1 is a 3T3R (on 5GHz) version of DIR-825 rev C1 (same PCB).+DIR-835 Rev A1 is a 3T3R (on 5GHz) version of [[toh/​d-link/​dir-825|D-Link ​DIR-825]] rev C1 (same PCB).
  
 Hardware is very similar to [[toh/​tp-link/​tl-wdr4300|TP-Link WDR4300]] but DIR-835 has more flash and is physically more compact. Hardware is very similar to [[toh/​tp-link/​tl-wdr4300|TP-Link WDR4300]] but DIR-835 has more flash and is physically more compact.
  
 ===== Supported Versions ===== ===== Supported Versions =====
-^ Version/​Model ​^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Model Specific ​Notes ^ +^ Version ^ Launch Date ^ S/N ^ OpenWrt Version Supported ^ Notes ^ 
-| A1  |  2012-03 ​ | - | Barrier Breaker [[https://​dev.openwrt.org/​changeset/​35403|r35403]] | [[https://​apps.fcc.gov/​oetcf/​eas/​reports/​ViewExhibitReport.cfm?​mode=Exhibits&​RequestTimeout=500&​calledFromFrame=N&​application_id=957289&​fcc_id=KA2IR835A1|FCC Filing]] |+| A1  |  2012-03 ​ | - | Barrier Breaker [[https://​dev.openwrt.org/​changeset/​35957|r35957]] | [[https://​apps.fcc.gov/​oetcf/​eas/​reports/​ViewExhibitReport.cfm?​mode=Exhibits&​RequestTimeout=500&​calledFromFrame=N&​application_id=957289&​fcc_id=KA2IR835A1|FCC Filing]] |
  
-**Note**: Current (as of r35608) DIR-**825**-C1 builds work on DIR-835-A1, but LED config is not quite right and they will all be turned off by default. Wireless output on this build is also maxed out by default and may need to be turned down (especially the 2.4 GHz band, which is putting out 501 mW). 
  
 ===== Hardware Highlights ===== ===== Hardware Highlights =====
 ^ Rev ^ CPU ^ Ram ^ Flash ^ Network ^ Gigabit ^ USB ^ Serial ^ JTag ^ ^ Rev ^ CPU ^ Ram ^ Flash ^ Network ^ Gigabit ^ USB ^ Serial ^ JTag ^
-| A1 | Atheros AR9344 ​560MHz| 128MB | 16MB | 4 + 1 | Yes | Yes | Yes | Yes +| A1 | Atheros AR9344 560MHz| 128MB | 16MB | 4+1 | Yes | Yes | Yes | Yes |
- +
-==== Flash Layout ==== +
-Please check out the article [[doc:​techref:​Flash Layout]]. It contains an example and a couple of explanations. +
-| 0x000000000000-0x000000010000 : "​u-boot"​ | +
-| 0x000000010000-0x000000020000 : "​nvram"​ | +
-| 0x000000020000-0x000000fb0000 : "​linux"​ | +
-| 0x000000160000-0x000000fb0000 : "​rootfs"​ | +
-| 0x000000fb0000-0x000000fe0000 : "​LANG"​ | +
-| 0x000000fe0000-0x000000ff0000 : "​MAC"​ | +
-| 0x000000ff0000-0x000001000000 : "​ART" ​|+
  
 ===== Installation ===== ===== Installation =====
Line 29: Line 18:
  
 ==== OEM easy installation ==== ==== OEM easy installation ====
-Flash **DIR-825-C1** "​factory"​ OpenWrt image file (e.g. openwrt-ar71xx-generic-**dir-825-c1**-squashfs-**factory**.bin) via D-Link firmware upgrade in web interface. ​+Flash **DIR-835-A1** "​factory"​ OpenWrt image file (e.g. openwrt-ar71xx-generic-**dir-835-a1**-squashfs-**factory**.bin) via D-Link firmware upgrade in web interface. ​*NOTE* the process completion is not obvious so give plenty of time and do not be confused as the LED power light will end up being AMBER instead of GREEN as on stock firmware; LED functionality can be adjusted through 'LUCI > System > Led Configuration'​. 
 + 
 +Direct firmware link: http://​downloads.openwrt.org/​barrier_breaker/​14.07/​ar71xx/​generic/​openwrt-ar71xx-generic-dir-835-a1-squashfs-factory.bin 
 | {{:​meta:​icons:​tango:​48px-dialog-warning.svg.png?​nolink}} | Note that default D-Link IP address is 192.168.__**0**__.1 and OpenWrt will default to 192.168.__**1**__.1. Make sure your PC obtains a new IP address from DHCP (or use static) after installation. Initial connection must be over ethernet (you should flash over ethernet anyway).| | {{:​meta:​icons:​tango:​48px-dialog-warning.svg.png?​nolink}} | Note that default D-Link IP address is 192.168.__**0**__.1 and OpenWrt will default to 192.168.__**1**__.1. Make sure your PC obtains a new IP address from DHCP (or use static) after installation. Initial connection must be over ethernet (you should flash over ethernet anyway).|
-  *Telnet to 192.168.1.1 and set a root password, or browse to http://​192.168.1.1 if LuCI is installed. ​Trunk builds will require you to manually install ​the Luci web interface ​(see [[doc/​howto/​luci.essentials]]). __WiFi is disabled by default__ as well, as it is with most other OpenWrt builds. ​+  *Telnet to 192.168.1.1 and set a root password, or browse to http://​192.168.1.1 if LuCI is installed. ​The file linked above (14.07) includes the Luci web interface, but note that trunk builds will require you to manually install ​it (see [[doc/​howto/​luci.essentials]]). __WiFi is disabled by default__ as well, as it is with most other OpenWrt builds. ​ 
 + 
 +This router also supports D-Link'​s recovery mode, which can be used for initial flash or recovery. See this D-link forum post for details: http://​forums.dlink.com/​index.php?​topic=44909.msg163599#​msg163599
  
 ==== OEM installation using TFTP ==== ==== OEM installation using TFTP ====
Line 41: Line 35:
 ->  [[doc:​howto:​generic.sysupgrade]] ->  [[doc:​howto:​generic.sysupgrade]]
  
-If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. 
  
-=== LuCI Web Upgrade Process ​=== +==== Flash Layout ​==== 
- +Please check out the article [[doc:techref:Flash Layout]]It contains an example and a couple of explanations
-  * Browse to http://​192.168.1.1/​cgi-bin/​luci/​mini/​system/​upgrade/​ LuCI Upgrade URL +| 0x000000000000-0x000000010000 : "​u-boot"​ | 
-  * Upload image file for sysupgrade to LuCI +| 0x000000010000-0x000000020000 : "​nvram"​ | 
-  * Wait for reboot +| 0x000000020000-0x000000fb0000 : "​linux"​ | 
- +| 0x000000160000-0x000000fb0000 : "​rootfs"​ | 
-=== Terminal Upgrade Process === +| 0x000000fb0000-0x000000fe0000 : "​LANG"​ | 
- +| 0x000000fe0000-0x000000ff0000 : "​MAC"​ | 
-  * Login as root via SSH on 192.168.1.1 +| 0x000000ff0000-0x000001000000 ​"​ART"​ |
-  * Use the following commands to upgrade. +
- +
-<​code>​ +
-cd /tmp/ +
-wget http://http://downloads.openwrt.org/​snapshots/​trunk/​XXX/​xxx.abc +
-sysupgrade /​tmp/​xxx.abc +
-</​code>​ +
- +
-  *If sysupgrade does not support this router, use the following commands. +
- +
-<​code>​ +
-cd /tmp/ +
-wget http://​http://​downloads.openwrt.org/​snapshots/​trunk/​XXX/​xxx.abc +
-mtd write /​tmp/​xxx.abc linux && reboot</​code>​+
  
 ===== Bootlogs ===== ===== Bootlogs =====
Line 1819: Line 1798:
 | **Wireless:​** ​       | Atheros AR9340 2.4GHz 802.11bgn | Atheros AR9380 5GHz 802.11an | | **Wireless:​** ​       | Atheros AR9340 2.4GHz 802.11bgn | Atheros AR9380 5GHz 802.11an |
 | **RegDomain:​** ​      | US | US | | **RegDomain:​** ​      | US | US |
-| **Ethernet:​** ​       | Atheros ​AR8327N ​Gigabit Switch |+| **Ethernet:​** ​       | Atheros ​AR8327 ​Gigabit Switch |
 | **USB:​** ​            | Yes 1 x 2.0     | | **USB:​** ​            | Yes 1 x 2.0     |
 | **[[doc:​hardware:​port.serial|Serial]]:​** ​         | [[#​Serial|Yes]] | | **[[doc:​hardware:​port.serial|Serial]]:​** ​         | [[#​Serial|Yes]] |
Line 1825: Line 1804:
  
 ==== Photos ==== ==== Photos ====
-[[https://​apps.fcc.gov/​eas/​GetApplicationAttachment.html?id=1570908|FCC External Photos]]+ [[https://​apps.fcc.gov/oetcf/eas/reports/​ViewExhibitReport.cfm?mode=Exhibits&​RequestTimeout=500&​calledFromFrame=N&​application_id=957289&​fcc_id=KA2IR835A1|FCC Filing]]
  
 Model Number Model Number
Line 1831: Line 1810:
 //Front:// //Front://
  
-**Photo of front of the casing**+http://​www.dlink.com/​-/​media/​Images/​Products/​DIR/​835/​DIR%20835%20Front.png
  
 //Back:// //Back://
  
-**Photo of back of the casing**+http://​www.dlink.com/​-/​media/​Images/​Products/​DIR/​835/​DIR%20835%20Back.png
  
 ==== Opening the case ==== ==== Opening the case ====
Line 1853: Line 1832:
  
 **Photo of PCB** **Photo of PCB**
-[[https://​apps.fcc.gov/​eas/​GetApplicationAttachment.html?id=1570911|FCC Internal Photos]]+ [[https://​apps.fcc.gov/oetcf/eas/reports/​ViewExhibitReport.cfm?mode=Exhibits&​RequestTimeout=500&​calledFromFrame=N&​application_id=957289&​fcc_id=KA2IR835A1|FCC Filing]]
  
 ==== Serial ==== ==== Serial ====
Line 1873: Line 1852:
 -> [[doc:​howto:​generic.debrick]] -> [[doc:​howto:​generic.debrick]]
  
-===== Bootloader Mods ===== +This router supports D-Link's recovery mode, which can be used for initial flash or recovery after a failed flash. Note that this is different than OpenWrt'​s failsafe mode. See this D-link forum post for detailshttp://​forums.dlink.com/​index.php?​topic=44909.msg163599#​msg163599 
-  ​you could read about [[doc:techref:bootloader]] in general+ 
 + 
  
-===== Hardware mods ===== 
-  - as a beginner, you really should inform yourself about [[doc:​hardware:​soldering]] in general and then obtain some practical experience! 
  
 ===== Notes ===== ===== Notes =====
Line 1887: Line 1866:
 For some Help with the Tags, please have a look here: [[meta/​tags]] For some Help with the Tags, please have a look here: [[meta/​tags]]
  
-{{tag>​GigabitEthernet USB ath9k DetachableAntenna 128RAM 16Flash MIPS MIPS32 74K 74kc ar9344 3ant 5ghz 3x3 2x2 2radio ​simultan 802.11abgn_simultan 802.11abgn 802.11bgn}}+{{tag>​GigabitEthernet USB ath9k DetachableAntenna 128RAM 16Flash MIPS MIPS32 74K 74kc ar9344 3ant 5ghz 3x3 2x2 2WNIC simultan 802.11abgn_simultan 802.11abgn 802.11bgn}}
toh/d-link/dir-835.1361208827.txt.bz2 · Last modified: 2013/02/18 18:33 (external edit)