Table of Contents
D-Link DSL-2641B ADSL + Wireless Router
Hardware info
| ADSL2+ Chip with CPU MIPS32 | FLASH 4MB | SDRAM 64MB | Switch 10/100MBit | WLAN 802.11b/g/n | WLAN Front-End | ASDL Line driver |
|---|---|---|---|---|---|---|
| Broadcom BCM63281KFBG | MX25L64 | MIRA P3R12E4JFF | Broadcom BCM6328B0 | Atheros 9287 | Atheros (possible: mac80211 ath9k >= 2.6.32) | Broadcom BCM96328 |
Board images
click for zoom
Serial port pinout
Console port uses 3.3 V signaling with settings 115200 8N1. Pin layout (from left):
| 1 | 2 | 3 | 4 |
|---|---|---|---|
| GND | RX | TX | VCC |
click for zoom
Default settings
LAN IP: 192.168.1.1/24 User name: admin Password: admin
Original Firmware Info
The original GPL sourcecode v1.00 can be downloaded here (rev c), | here (rev e), |here (rev f1). It consist on a Linux 2.6.30 kernel with some binary and some opensource Broadcom tools & drivers and sourcecode of the kernel and the rest of tools.
Open source drivers: flash, led, spi, serial, rnd (random number generator), network (smux, atm/ptm)
Binary only: adsl, bcm log, bcm ethernet, bcm wireless, fap, 802.1ag, power management, vlan, xtmcfg
The toolchain is included (rev f1) and it has gcc 4.4.2.
Boot log
\0x00HELO
CPUI
L1CI
DRAM
----
PHYS
ZQDN
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN
CFE version 1.0.37-106.5 for BCM96328 (32bit,SP,BE)
Build Date: å\0x9b\0x9b 8æ\0x9c\0x88 26 15:29:39 CST 2010 (jason@jason-desktop)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name MX25L64, id 0xc217 size 8192KB
Total Flash size: 8192K with 128 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-4) : AW4339U
Number of MAC Addresses (1-32) : 11
Base MAC Address : 14:d6:4d:f3:cd:5b
PSI Size (1-128) KBytes : 128
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1\0x081\0x080
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (root@owen-UB) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Thu Apr 14 09:01:40 CST 2011
HS Serial flash device: name MX25L64, id 0xc217 size 8192KB
AW4339U prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 80282420, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 61080k/64512k available (2113k kernel code, 3412k reserved, 396k data, 116k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 816 bytes
NET: Registered protocol family 16
Total Flash size: 8192K with 128 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x00ffff]
pci 0000:02:00.0: supports D1
pci 0000:02:00.0: PME# supported from D0 D1 D3hot
pci 0000:02:00.0: PME# disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
msgmni has been set to 119
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x8018 is enabled
SES: LED GPIO 0x8009 is enabled
Invalid External Interrupt definition
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 36) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Apr 14 2011 08:59:20
Broadcom Logger v0.1 Apr 14 2011 08:59:04
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 116k freed
init started: BusyBox v1.00 (2011.04.14-01:02+0000) multi-call binary
mount: Mounting sysfs on /sys failed: No such devi
BusyBox v1.00 (2011.04.14-01:02+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
cp: /bin/CP850.so: No such file or directory
bcmxtmcfg: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6328B0 Ethernet Network Device v0.1 Apr 14 2011 08:59:12
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: 14:D6:4D:F3:CD:5B
eth1: MAC Address: 14:D6:4D:F3:CD:5B
eth2: MAC Address: 14:D6:4D:F3:CD:5B
eth3: MAC Address: 14:D6:4D:F3:CD:5B
ath_hal: 0.9.17.1 (AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2316, RF2317, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_dfs: Version 2.0.0
Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved
wlan: 0.8.4.2 (Atheros/multi-bss)
ath_rate_atheros: Version 2.0.1
Copyright (c) 2001-2004 Atheros Communications, Inc, All Rights Reserved
ath_pci: 0.9.4.5 (Atheros/multi-bss)
ath_pci: CR-LSDK-1.4.0.112
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
string = 0xa5
ar5416EepromAttach: Read calibration data from FLASH successfully
Chan Freq RegPwr HT CTL CTL_U CTL_L DFS
1 2412n 27 HT40 1 0 1 N
1 2412n 27 HT20 1 0 0 N
2 2417n 27 HT20 1 0 0 N
2 2417n 27 HT40 1 0 1 N
3 2422n 27 HT40 1 0 1 N
3 2422n 27 HT20 1 0 0 N
4 2427n 27 HT40 1 0 1 N
4 2427n 27 HT20 1 0 0 N
5 2432n 27 HT40 1 1 0 N
5 2432n 27 HT40 1 0 1 N
5 2432n 27 HT20 1 0 0 N
6 2437n 27 HT40 1 1 0 N
6 2437n 27 HT40 1 0 1 N
6 2437n 27 HT20 1 0 0 N
7 2442n 27 HT40 1 0 1 N
7 2442n 27 HT20 1 0 0 N
7 2442n 27 HT40 1 1 0 N
8 2447n 27 HT40 1 1 0 N
8 2447n 27 HT20 1 0 0 N
9 2452n 27 HT40 1 1 0 N
9 2452n 27 HT20 1 0 0 N
10 2457n 27 HT40 1 1 0 N
10 2457n 27 HT20 1 0 0 N
11 2462n 27 HT40 1 1 0 N
11 2462n 27 HT20 1 0 0 N
dfs_init_radar_filters: dfs->dfs_rinfo.rn_numradars: 0
DFS min filter rssiThresh = 18
DFS max pulse dur = 131 ticks
wifi0: 11nght20 rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11nght20 MCS: 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
wifi0: 11nght40plus rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11nght40plus MCS: 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
wifi0: 11nght40minus rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
wifi0: 11nght40minus MCS: 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15
wifi0: mac 384.2 phy 15.15 radio 12.0
wifi0: Use hw queue 1 for WME_AC_BE traffic
wifi0: Use hw queue 0 for WME_AC_BK traffic
wifi0: Use hw queue 2 for WME_AC_VI traffic
wifi0: Use hw queue 3 for WME_AC_VO traffic
wifi0: Use hw queue 8 for CAB traffic
wifi0: Use hw queue 9 for beacons
wifi0: Use hw queue 7 for UAPSD
wifi0: Atheros 9287: mem=0x10f00000, irq=31 hw_base=0xb0f00000
wlan: mac acl policy registered
p8021ag: p8021ag_init entry
Broadcom 802.1Q VLAN Interface, v0.1
===== Release Version EU_1.00 (build timestamp 2011.04.14-09:02:20) =====
device eth0 entered promiscuous mode
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
device eth3 entered promiscuous mode
interface ath0 does not exist!
SIOCGIFFLAGS: No such device
SIOCSIFADDR: No such device
WLmngr Daemon is running
Atheros WLmngr Daemon is running
BcmAdsl_Initialize=0xC00B5FEC, g_pFnNotifyCallback=0xC00D9DF4
pSdramPHY=0xA3FFFFF8, 0xE916A 0xDEADBEEF
ath0
I am before: 0
before ieee80211_check_mode_consistency
after ieee80211_check_mode_consistency
After RUN check
after radar check:
Scan
device ath0 entered promiscuous mode
*** PhySdramSize got adjusted: 0x73038 => 0x88D78 ***
AdslCoreSharedMemInit: shareMemAvailable=488032
AdslCoreHwReset: AdslOemDataAddr = 0xA3F69710
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ath_newstate:
Resetting (ath_newstate); Code: 04
ieee80211_newstate:
ic->ic_cwm.cw_width :0, ic->ic_cwm.cw_extoffset: 0
ic->ic_cwm.cw_width :0, ic->ic_cwm.cw_extoffset: 0
ath_newstate:
Resetting (ath_newstate); Code: 04
ieee80211_newstate:
ath_chan_set: Changing to channel 2437, Flags 40080, PF 40
ath_newstate:
ieee80211_newstate:
br0: port 5(ath0) entering forwarding state
ath_newstate:
ieee80211_newstate:
br0: port 5(ath0) entering disabled state
iptables v1.4.0: can't initialize iptables table `nat': iptables who? (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
monitor task is initialized pid= 205
Switch MDK: num_switches = 1
Switch MDK: unit = 0; phy_pbmp = 0xf; config_pbmp = 0xf
Switch MDK link poll thread: unit=0; phypbmp=0xf
tr69c:error:10.847:updateTr69cCfgInfo:687:acsState.connReqURL (null), acsCfg->connectionRequestURL (null)
tr69c:error:10.847:updateTr69cCfgInfo:710:connReqURLchanged 0
tr69c:error:10.848:readMessageFromSmd:890:got SYSTEM_BOOT, adding eIEBoot to informEvList
ath1
I am before: 0
before ieee80211_check_mode_consistency
after ieee80211_check_mode_consistency
After RUN check
after radar check:
Scan
ath2
I am before: 0
before ieee80211_check_mode_consistency
after ieee80211_check_mode_consistency
After RUN check
after radar check:
Scan
ath3
I am before: 0
before ieee80211_check_mode_consistency
after ieee80211_check_mode_consistency
After RUN check
after radar check:
Scan
optarg=0 shmId=0
wlevt_init@107: opened loopback socket 4
wlevt is ready for new msg...
killall: wpa_supplicant: no process killed
ath_newstate:
ieee80211_newstate:
device ath0 left promiscuous mode
br0: port 5(ath0) entering disabled state
ath_newstate:
ieee80211_newstate:
ath_newstate:
ieee80211_newstate:
ath_newstate:
ieee80211_newstate:
wlanconfig: ioctl: No such device
There is no Predefined DevicePin in CFE
WPS Device PIN = 73159247
interface ath0 does not exist!
interface ath0 does not exist!
SIOCGIFFLAGS: No such device
SIOCSIFADDR: No such device
ath0
device ath0 entered promiscuous mode
ath_newstate:
Resetting (ath_newstate); Code: 04
ieee80211_newstate:
*****Channel 6 noiseFlr -120 intRssi -3
ath_chan_set: Changing to channel 2432, Flags 40080, PF 40
br0: port 5(ath0) entering forwarding state
ath_newstate:
ieee80211_newstate:
*****Channel 5 noiseFlr -120 intRssi -1
ath_chan_set: Changing to channel 2437, Flags 40080, PF 40
br0: port 5(ath0) entering disabled state
ath1
ath2
ath3
WPS Mode = []
ath_ioctl: set countrycode:826
Chan Freq RegPwr HT CTL CTL_U CTL_L DFS
1 2412n 20 HT20 1 0 0 N
1 2412n 20 HT40 1 0 1 N
2 2417n 20 HT40 1 0 1 N
2 2417n 20 HT20 1 0 0 N
3 2422n 20 HT20 1 0 0 N
3 2422n 20 HT40 1 0 1 N
4 2427n 20 HT40 1 0 1 N
4 2427n 20 HT20 1 0 0 N
5 2432n 20 HT40 1 1 0 N
5 2432n 20 HT40 1 0 1 N
5 2432n 20 HT20 1 0 0 N
6 2437n 20 HT40 1 1 0 N
6 2437n 20 HT40 1 0 1 N
6 2437n 20 HT20 1 0 0 N
7 2442n 20 HT40 1 0 1 N
7 2442n 20 HT20 1 0 0 N
7 2442n 20 HT40 1 1 0 N
8 2447n 20 HT40 1 1 0 N
8 2447n 20 HT40 1 0 1 N
8 2447n 20 HT20 1 0 0 N
9 2452n 20 HT40 1 1 0 N
9 2452n 20 HT40 1 0 1 N
9 2452n 20 HT20 1 0 0 N
10 2457n 20 HT40 1 1 0 N
10 2457n 20 HT20 1 0 0 N
11 2462n 20 HT40 1 1 0 N
11 2462n 20 HT20 1 0 0 N
12 2467n 20 HT40 1 1 0 N
12 2467n 20 HT20 1 0 0 N
13 2472n 20 HT40 1 1 0 N
13 2472n 20 HT20 1 0 0 N
dfs_init_radar_filters: dfs->dfs_rinfo.rn_numradars: 0
DFS min filter rssiThresh = 21
DFS max pulse dur = 131 ticks
Chan Freq RegPwr HT CTL CTL_U CTL_L DFS
1 2412n 20 HT20 1 0 0 N
1 2412n 20 HT40 1 0 1 N
2 2417n 20 HT40 1 0 1 N
2 2417n 20 HT20 1 0 0 N
3 2422n 20 HT20 1 0 0 N
3 2422n 20 HT40 1 0 1 N
4 2427n 20 HT40 1 0 1 N
4 2427n 20 HT20 1 0 0 N
5 2432n 20 HT40 1 1 0 N
5 2432n 20 HT40 1 0 1 N
5 2432n 20 HT20 1 0 0 N
6 2437n 20 HT40 1 1 0 N
6 2437n 20 HT40 1 0 1 N
6 2437n 20 HT20 1 0 0 N
7 2442n 20 HT40 1 0 1 N
7 2442n 20 HT20 1 0 0 N
7 2442n 20 HT40 1 1 0 N
8 2447n 20 HT40 1 1 0 N
8 2447n 20 HT40 1 0 1 N
8 2447n 20 HT20 1 0 0 N
9 2452n 20 HT40 1 1 0 N
9 2452n 20 HT40 1 0 1 N
9 2452n 20 HT20 1 0 0 N
10 2457n 20 HT40 1 1 0 N
10 2457n 20 HT20 1 0 0 N
11 2462n 20 HT40 1 1 0 N
11 2462n 20 HT20 1 0 0 N
12 2467n 20 HT40 1 1 0 N
12 2467n 20 HT20 1 0 0 N
13 2472n 20 HT40 1 1 0 N
13 2472n 20 HT20 1 0 0 N
I am before: 0
I am before: 0
device ath0 left promiscuous mode
br0: port 5(ath0) entering disabled state
device ath0 entered promiscuous mode
ath_newstate:
Resetting (ath_newstate); Code: 04
ieee80211_newstate:
*****Channel 6 noiseFlr -120 intRssi -3
ath_chan_set: Changing to channel 2412, Flags 20080, PF 40
br0: port 5(ath0) entering forwarding state
*****Channel 1 noiseFlr -120 intRssi 2050
ath_chan_set: Changing to channel 2417, Flags 20080, PF 40
*****Channel 2 noiseFlr -120 intRssi -3
ath_chan_set: Changing to channel 2422, Flags 20080, PF 0
*****Channel 3 noiseFlr -119 intRssi 32762
ath_chan_set: Changing to channel 2427, Flags 20080, PF 0
Reaped 1188
*****Channel 4 noiseFlr -121 intRssi 0
ath_chan_set: Changing to channel 2432, Flags 20080, PF 0
*****Channel 5 noiseFlr -120 intRssi -1
ath_chan_set: Changing to channel 2437, Flags 20080, PF 0
*****Channel 6 noiseFlr -120 intRssi -3
ath_chan_set: Changing to channel 2442, Flags 20080, PF 0
*****Channel 7 noiseFlr -120 intRssi 0
ath_chan_set: Changing to channel 2447, Flags 20080, PF 40
*****Channel 8 noiseFlr -120 intRssi 0
ath_chan_set: Changing to channel 2452, Flags 20080, PF 40
UPnP daemon is ready to run
*****Channel 9 noiseFlr -120 intRssi -28664
ath_chan_set: Changing to channel 2437, Flags 40080, PF 40
******* channel 1 average rssi 32 noise floor -120 final average rssi -208
******* channel 6 average rssi 15 noise floor -120 final average rssi -225
find_best_11ng_centerchan: found best center chan: 6
ic->ic_cwm.cw_width :0, ic->ic_cwm.cw_extoffset: 0
ic->ic_cwm.cw_width :0, ic->ic_cwm.cw_extoffset: 0
ath_newstate:
Resetting (ath_newstate); Code: 04
ieee80211_newstate:
ath_chan_set: Changing to channel 2437, Flags 20080, PF 0
ath_newstate:
ieee80211_newstate:
/bin/eapd: not found
/bin/nas: not found
Reading topology file /var/topology_ap.conf ...
ath_newstate:
ieee80211_newstate:
br0: port 5(ath0) entering disabled state
Could not connect to kernel driver.
Using interface ath0 with hwaddr 14:d6:4d:f3:cd:5c and ssid 'D-Link DSL-2741B'
ath_newstate:
Resetting (ath_newstate); Code: 04
ieee80211_newstate:
******* channel 1 average rssi 32 noise floor -120 final average rssi -208
Ignore the current channel 6
find_best_11ng_centerchan: found best center chan: 1
ic->ic_cwm.cw_width :0, ic->ic_cwm.cw_extoffset: 0
ic->ic_cwm.cw_width :0, ic->ic_cwm.cw_extoffset: 0
ath_newstate:
Resetting (ath_newstate); Code: 04
ieee80211_newstate:
ath_chan_set: Changing to channel 2412, Flags 20080, PF 40
ath_newstate:
ieee80211_newstate:
br0: port 5(ath0) entering forwarding state
l2_packet_receive - recvfrom: Network is down
wpatalk: INFO: Connection (re)established to daemon=hostapd interface=ath0
wpatalk: INFO: ... using socket-file=/var/run/hostapd/ath0
wpatalk: INFO: SEND-RAW: CONFIGSTOP
wpatalk: INFO: GOT-RESPONSE: OK
killall: wpatalk: no process killed
wpatalk: INFO: Connection (re)established to daemon=hostapd interface=ath0
wpatalk: INFO: ... using socket-file=/var/run/hostapd/ath0
wpatalk: INFO: SEND-RAW: CONFIGME pin=73159247 timeout=120
wpatalk: INFO: GOT(cb): <2>CTRL-REQ-WPS-JOB-READY:[new start]-AP button pushed or PIN entered
wpatalk: INFO: GOT-RESPONSE: OK
BCM96328 Broadband Router
Login: admin
Password:
> sh
BusyBox v1.00 (2011.04.14-01:02+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
#
toh/d-link/dsl-2741b.txt · Last modified: 2012/04/05 13:25 by crissi