You are here: OpenWrt Wiki » Table of Hardware » D-Link » D-Link DSL-G624T

Differences

This shows you the differences between two versions of the page.

--- toh:d-link:dsl-624t [2013/02/02 11:52]
alessandro_s
+++ toh:d-link:dsl-624t [2013/03/26 22:25] (current)
alessandro_s
@@ Line 1: / Line 1: @@
-====== D-Link DSL-624T ======
+====== D-Link DSL-G624T ======
-D-Link DSL-624T ADSL2/2+ Router
+D-Link DSL-G624T ADSL2/2+ Router
 ===== Hardware Highlights =====
@@ Line 6: / Line 6: @@
 | TI AR7 (TNETD7300)@150MHz | 16MB | 4MB | 4 x 1 + ADSL2/2+ | No | Yes | Yes |
-The DSL-624T is an evolution of the previous ADSL1-only [[dsl-504t|DSL-504T]] (edit: at least some 504T were adsl2 capable, modern firmware is needed, like the one here: ftp://ftp.dlink.ru/pub/ADSL/DSL-504T/Firmware/ADSL2_plus/AnnexM/ one reported syncing at 13Mb/s). It is the same board of the wireless-deprived [[dsl-524t|DSL-G524T]] (the 524T board has empty solders point where the 624T has the VLYNQ ACX wireless card).
+The DSL-G624T is an evolution of the previous ADSL1-only [[dsl-504t|DSL-504T]]. It is the same board of the wireless-deprived [[dsl-524t|DSL-G524T]] (the 524T board has empty soldering points for the mini-PCI slot where the G624T has the VLYNQ ACX wireless card).
@@ Line 13: / Line 13: @@
 ==== Info ====
-(To be checked for accuracy)
 | **Architecture:** MIPS (little endian) |
 | **Vendor:** D-Link |
@@ Line 27: / Line 27: @@
 | **ADSL:** TI AR7, ADSL2/2+ (up to 24Mbit/s) |
 | **USB:** No |
-| **Serial:** [[#Serial|Yes]], 3.3V (the kernel finds 2 serial ports) |
+| **Serial:** [[#serial.port|Yes]], 3.3V (the kernel reports 2 serial ports, but only one jumper is available on the board) |
 | **JTAG:** [[#JTAG|Yes]] |
 | **Power supply:** 12V, 1.2A |
 ==== Photos ====
@@ Line 45: / Line 44: @@
 {{:media:d-link_dsl-g624t_inside.jpg|}}
+Inside view of a burned-out unit, with EM shield and wireless card removed to fully expose the Mini-PCI slot:
+{{:media:d-link_dsl-g624t_mini-pci.jpg|}}
+Mini-PCI wireless module: front view:
+{{:media:d-link_dsl-g624t_mini-pci_wireless-front.jpg|}}
+The TI chip markings read:
+''TNETW1130ZVF
+CPG108 D4''
+Mini-PCI wireless module: rear view:
+{{:media:d-link_dsl-g624t_mini-pci_wireless-rear.jpg|}}
 ==== Opening the case ====
@@ Line 50: / Line 66: @@
 The top and bottom shells are kept toghether by only two screws, easily accessible and removable from the bottom.
-==== Serial ====
+==== Serial Port ====
-Untested, but should be just like the 524T's [[dsl-524t#serial]] port. It's the **JP6** connector.
+Just like the 524T's [[dsl-524t#serial]] port. It's the **JP6** connector. It needs a TTL (3.3V) to RS232 converter such as a MAX3232 in order to be interfaced to a PCs' serial port.
+^  **D-Link DSL-624T Serial connector pinout**  ^^^^^
+^ Pin num. ^ Name ^ Signal ^
+| 1 | RXD | Receive Data In |
+| 2 | GND | Ground |
+| 3 | Vcc (3.3) | Power |
+| 4 | GND | Ground |
+| 5 | TXD | Transmit Data Out |
+In order to use the serial connection, the DTE (the computer) must set it's serial port to 38400 baud, 8 bit, no parity, 1 stop bit.
+Would one use a MAX3232 (or like) serial converter, connections must be arranged in the following way:
+^  ** DSL-624T serial port to MAX3232 connections **  ^^^^^^
+^ DSL-624 serial port ^^^ MAX3232 ^^^
+^ pin# ^ Name ^ Signal ^ pin# ^ Name ^ Signal ^
+| 1 | RXD | Receive Data In | 12 | R1OUT | TTL/CMOS Receiver Output |
+| 2 | GND | Ground | 15 | GND | Ground |
+| 3 | Vcc (3.3) | Power | 16 | Vcc | Power |
+| 4 | GND | Ground | 15 | GND | Ground |
+| 5 | TXD | Transmit Data Out | 11 | T1IN | TTL/CMOS Transmitter Input |
+^  ** MAX3232 to DB9/15 RS232 serial port connections **  ^^^^^^^^
+^ MAX3232 ^^^ RS232 serial port ^^^^
+^ pin# ^ Name ^ Signal ^ DB-9 pin# ^ DB-15 pin#  ^ Name ^ Signal ^
+| 14 | T1OUT | RS-232 Transmitter Output | 2 | 3 | RXD | Receive Data In |
+| 13 | R1IN | RS-232 Receiver Input | 3 | 2 | TXD | Transmit Data Out |
+| 15 | GND | Ground | 5 | 7 | GND | Ground |
+At powerup the following lines are displayed:
+<code>
+ADAM2 Revision 0.22.02_b04_Mar  9 2005
+(C) Copyright 1996-2003 Texas Instruments Inc. All Rights Reserved.
+(C) Copyright 2003 Telogy Networks, Inc.
+Usage: setmfreq [-d] [-s sys_freq, in MHz] [cpu_freq, in MHz]
+Memory optimization Complete!
+Adam2_AR7RD >
+Press any key to abort OS load, or wait 7 seconds for OS to boot...
+</code>
+They are followed by the boot messages that are shown by the dmesg command (see below), plus these three lines at about line 85:
+<code>- init -
+Please press Enter to activate this console.
+</code>
 ==== JTAG ====
-The 524T appears to have a JTAG header (untested). See [[http://downloads.openwrt.org/tools/oem/jtag/tools.zip|JTAG tools]] and [[doc:hardware:port.jtag]] for more details.
+The G624T appears to have a JTAG header (untested). See [[http://downloads.openwrt.org/tools/oem/jtag/tools.zip|JTAG tools]] and [[doc:hardware:port.jtag]] for more details.
@@ Line 79: / Line 146: @@
 To use OpenWrt Backfire (10.03.1) on this unit we need to modify the partition layout as follows (changes are in **bold**):
-^  **D-Link DSL-624T and OpenWrt**  ^^^^^
+^  **D-Link DSL-624T and OpenWrt**  ^^^^^^
-^ partition ^ Name ^ start ^ end ^ Description  ^
+^ partition ^ Name ^ start ^ end ^ size ^ Description  ^
-| mtd2 | loader   | 0x90000000 | 0x90010000 | Bootloader (ADAM2) |
+| mtd2 | loader   | 0x90000000 | 0x90010000 | 64 KiB | Bootloader (ADAM2) |
-| mtd1 | linux    | **0x90010000** | **0x903f0000** | Linux kernel |
+| mtd1 | linux    | **0x90010000** | **0x903f0000** | **3968** KiB | Linux kernel |
-| mtd0 | rootfs   | **0x900a1000** | **0x903f0000** | Read-only squashfs + jffs2 filesystem |
+| mtd0 | rootfs   | **0x900a1000** | **0x903f0000** | **3388** KiB | Read-only squashfs + jffs2 filesystem |
-| mtd3 | config   | 0x903f0000 | 0x90400000 | Original firmware configuration |
+| mtd3 | config   | 0x903f0000 | 0x90400000 | 64 KiB | Original firmware configuration |
-| mtd4 | rootfs_data | 0x90010000 | 0x903f0000 | |
+| mtd4 | rootfs_data | 0x90010000 | 0x903f0000 | 3968 KiB | |
@@ Line 205: / Line 272: @@
   * 1/3 shot Vodka     then Vodka.
  ---------------------------------------------------
-root@modem1:~# uname -r
+root@modem1:~#</code>
-.6.32.27
-root@modem1:~# cat /proc/cpuinfo
+<code>root@modem1:~# uname -r
+.6.32.27</code>
+<code>root@modem1:~# cat /proc/cpuinfo
 system type             : TI AR7 (TNETD7300)
 processor               : 0
@@ Line 222: / Line 292: @@
 VCED exceptions         : not available
 VCEI exceptions         : not available
-root@modem1:~# cat /proc/ioports
+</code>
+<code>root@modem1:~# cat /proc/ioports
 root@modem1:~# cat /proc/interrupts
            CPU0
@@ Line 237: / Line 309: @@
 ERR:          0
-root@modem1:~#  ls -F /proc
+</code>
+<code>root@modem1:~#  ls -F /proc
 /             4/             buddyinfo      irq/           slabinfo
 /         5/             bus/           kcore          softirqs
@@ Line 252: / Line 326: @@
 /            8/             iomem          partitions     vmstat
 /             avalanche/     ioports        self@          zoneinfo
-root@modem1:~# free
+</code>
+<code>root@modem1:~# free
               total         used         free       shared      buffers
   Mem:        12488        10100         2388            0          856
  Swap:            0            0            0
 Total:        12488        10100         2388
-root@modem1:~# cat /proc/softirqs
+</code>
+<code>root@modem1:~# cat /proc/softirqs
                 CPU0
       HI:          0
@@ Line 269: / Line 347: @@
  HRTIMER:          0
      RCU:     914167
-root@modem1:~# cat /proc/devices
+</code>
+<code>root@modem1:~# cat /proc/devices
 Character devices:
 mem
@@ Line 305: / Line 385: @@
     14100000-14333cfb : Kernel code
 cfc-1438c27f : Kernel data
-root@modem1:~# cat /proc/diskstats
+</code>
+<code>root@modem1:~# cat /proc/diskstats
        0 mtdblock0 3 13 128 10 0 0 0 0 0 10 10
        1 mtdblock1 0 0 0 0 0 0 0 0 0 0 0
@@ Line 311: / Line 393: @@
        3 mtdblock3 79 2132 4422 850 0 0 0 0 0 810 850
        4 mtdblock4 1 3 32 0 0 0 0 0 0 0 0
-root@modem1:~# cat /proc/modules
+</code>
-tiatm 121280 0 - Live 0x94580000
-acx 113200 0 - Live 0x944a0000
+<code>root@modem1:~# dmesg
-nf_nat_tftp 432 0 - Live 0x94d8d000
+Linux version 2.6.32.27 (jow@nd-build-02.linux-appliance.net) (gcc version 4.3.3 (GCC) ) #5 Wed Dec 21 01:54:33 CET 2011
-nf_conntrack_tftp 2400 1 nf_nat_tftp, Live 0x94e24000
+bootconsole [early0] enabled
-nf_nat_irc 864 0 - Live 0x94e78000
+CPU revision is: 00018448 (MIPS 4KEc)
-nf_conntrack_irc 2592 1 nf_nat_irc, Live 0x94eb1000
+TI AR7 (TNETD7300), ID: 0x0005, Revision: 0x27
-nf_nat_ftp 1360 0 - Live 0x94e48000
+Determined physical RAM map:
-nf_conntrack_ftp 4896 1 nf_nat_ftp, Live 0x94e8e000
+ memory: 01000000 @ 14000000 (usable)
-ipt_MASQUERADE 992 1 - Live 0x943a4000
+Initrd not found or empty - disabling initrd
-iptable_nat 2880 1 - Live 0x94dc0000
+Zone PFN ranges:
-nf_nat 12544 5 nf_nat_tftp,nf_nat_irc,nf_nat_ftp,ipt_MASQUERADE,iptable_nat, Live 0x943a8000
+  Normal   0x00014000 -> 0x00015000
-xt_NOTRACK 672 0 - Live 0x94e45000
+Movable zone start PFN for each node
-iptable_raw 656 1 - Live 0x94da9000
+early_node_map[1] active PFN ranges
-xt_state 800 3 - Live 0x94ec7000
+: 0x00014000 -> 0x00015000
-nf_conntrack_ipv4 8352 6 iptable_nat,nf_nat, Live 0x94ebc000
+On node 0 totalpages: 4096
-nf_defrag_ipv4 608 1 nf_conntrack_ipv4, Live 0x94e0f000
+free_area_init_node: node 0, pgdat 9438bc40, node_mem_map 943c8000
-nf_conntrack 44032 12 nf_nat_tftp,nf_conntrack_tftp,nf_nat_irc,nf_conntrack_irc,nf_nat_ftp,nf_conntrack_ftp,ipt_MASQUERADE,iptable_nat,nf_nat,xt_NOTRACK,xt_state,nf_conntrack_ipv4, Live 0x94450000
+  Normal zone: 32 pages used for memmap
-pppoe 10208 0 - Live 0x9439c000
+  Normal zone: 0 pages reserved
-pppox 1312 1 pppoe, Live 0x94395000
+  Normal zone: 4064 pages, LIFO batch:0
-pppoatm 2816 0 - Live 0x9438e000
+Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
-ipt_REJECT 1984 2 - Live 0x94ec4000
+Kernel command line: rootfstype=squashfs,jffs2 console=ttyS0,38400n8
-xt_TCPMSS 2720 0 - Live 0x94ece000
+PID hash table entries: 64 (order: -4, 256 bytes)
-ipt_LOG 4640 0 - Live 0x94ee4000
+Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
-xt_comment 464 0 - Live 0x94bec000
+Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
-xt_multiport 1904 0 - Live 0x94eef000
+Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
-xt_mac 576 0 - Live 0x94ee9000
+Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 16 bytes
-xt_limit 1152 1 - Live 0x94edc000
+Memory: 12352k/16384k available (2255k kernel code, 4032k reserved, 353k data, 136k init, 0k highmem)
-iptable_mangle 992 1 - Live 0x94ee3000
+Hierarchical RCU implementation.
-iptable_filter 768 1 - Live 0x94dbb000
+NR_IRQS:256
-ip_tables 8864 4 iptable_nat,iptable_raw,iptable_mangle,iptable_filter, Live 0x94e34000
+Clocks: prediv: 1, postdiv: 1, mul: 10
-xt_tcpudp 1856 3 - Live 0x94e8b000
+Calibrating delay loop... 149.50 BogoMIPS (lpj=747520)
-x_tables 9824 13 ipt_MASQUERADE,iptable_nat,xt_NOTRACK,xt_state,ipt_REJECT,xt_TCPMSS,ipt_LOG,xt_comment,xt_multiport,xt_mac,xt_limit,ip_tables,xt_tcpudp, Live 0x94e7c000
+Mount-cache hash table entries: 512
-ppp_async 9040 0 - Live 0x94eb8000
+NET: Registered protocol family 16
-ppp_generic 21216 4 pppoe,pppox,pppoatm,ppp_async, Live 0x94e80000
+bio: create slab <bio-0> at 0
-slhc 5360 1 ppp_generic, Live 0x94dcc000
+Switching to clocksource MIPS
-br2684 6624 0 - Live 0x94d60000
+NET: Registered protocol family 2
-atm 42896 3 tiatm,pppoatm,br2684, Live 0x94e90000
+IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
-crc_ccitt 976 1 ppp_async, Live 0x94be7000
+TCP established hash table entries: 512 (order: 0, 4096 bytes)
-root@modem1:~# cat /proc/timer_list
+TCP bind hash table entries: 512 (order: -1, 2048 bytes)
+TCP: Hash tables configured (established 512 bind 512)
+TCP reno registered
+NET: Registered protocol family 1
+squashfs: version 4.0 (2009/01/31) Phillip Lougher
+Registering mini_fo version $Id$
+JFFS2 version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
+msgmni has been set to 24
+io scheduler noop registered
+io scheduler deadline registered (default)
+Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
+serial8250: ttyS0 at MMIO 0x8610e00 (irq = 15) is a TI-AR7
+console [ttyS0] enabled, bootconsole disabled
+serial8250: ttyS1 at MMIO 0x8610f00 (irq = 16) is a TI-AR7
+physmap platform flash device: 00800000 at 10000000
+physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
+physmap-flash.0: Found an alias at 0x400000 for the chip at 0x0
+ CFI mfr 0x00000001
+ CFI id  0x000022f9
+ Amd/Fujitsu Extended Query Table at 0x0040
+  Amd/Fujitsu Extended Query version 1.1.
+number of CFI chips: 1
+cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
+cmdlinepart partition parsing not available
+RedBoot partition parsing not available
+ar7part partitions found on MTD device physmap-flash.0
+Creating 4 MTD partitions on "physmap-flash.0":
+x000000000000-0x000000010000 : "loader"
+x0000003f0000-0x000000400000 : "config"
+x000000010000-0x0000003f0000 : "linux"
+x0000000f0000-0x0000003f0000 : "rootfs"
+mtd: partition "rootfs" set to be root filesystem
+mtd: partition "rootfs_data" created automatically, ofs=2B0000, len=140000
+x0000002b0000-0x0000003f0000 : "rootfs_data"
+Fixed MDIO Bus: probed
+cpmac-mii: probed
+cpmac: device eth0 (regs: 08612800, irq: 41, phy: 0:01, mac: 00:17:9a:1e:00:00)
+cpmac: device eth1 (regs: 08610000, irq: 27, phy: 0:00, mac: 00:17:9a:1e:00:00)
+Registered led device: status
+vlynq0: regs 0x08611800, irq 29, mem 0x04000000
+vlynq0: using local clock divisor 8
+Found a VLYNQ device: 00000009
+vlynq1: regs 0x08611c00, irq 33, mem 0x0c000000
+TCP westwood registered
+NET: Registered protocol family 17
+.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
+All bugs added by David S. Miller <davem@redhat.com>
+VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
+Freeing unused kernel memory: 136k freed
+Please be patient, while OpenWrt loads ...
+mini_fo: using base directory: /
+mini_fo: using storage directory: /overlay
+PHY: 0:01 - Link is Up - 100/Full
+device eth0 entered promiscuous mode
+br-lan: port 1(eth0) entering forwarding state
+device eth1 entered promiscuous mode
+br-lan: port 2(eth1) entering forwarding state
+NET: Registered protocol family 8
+NET: Registered protocol family 20
+PHY: 0:00 - Link is Up - 100/Full
+PPP generic driver version 2.4.2
+ip_tables: (C) 2000-2006 Netfilter Core Team
+NET: Registered protocol family 24
+nf_conntrack version 0.5.0 (195 buckets, 780 max)
+CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
+nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
+sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
+acx: this driver is still EXPERIMENTAL
+acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion
+acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them
+acx: running on a little-endian CPU
+acx: PCI/VLYNQ module v0.3.37 initialized, waiting for cards to probe...
+Driver found for VLYNQ device: 00000009
+vlynq0: using local clock divisor 2
+acx: found TI TNETW1130-based wireless network card at <NULL>, irq:80, phymem:0x4000000, mem:0xa4000000
+initial debug setting is 0x000A
+using IRQ 80
+acx: need to load firmware for acx111 chipset with radio ID 16, please provide via firmware hotplug:
+acx: either one file only (<c>ombined firmware image file, radio-specific) or two files (radio-less base image file *plus* separate <r>adio-specific extension file)
+requesting firmware image 'tiacx111c16'
+acx_vlynq vlynq0: firmware: requesting tiacx111c16
+acx_write_fw (main/combined): 0
+acx_validate_fw (main/combined): 0
+initializing max packet templates
+dump queue head (from card):
+len: 24
+tx_memory_block_address: 19E40
+rx_memory_block_address: 15240
+tx1_queue address: 14774
+rx1_queue address: 14434
+NVS_vendor_offs:01CD probe_delay:200 eof_memory:1114112
+CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01
+AntennaID:00 Len:02 Data:01 02
+PowerLevelID:01 Len:02 Data:001E 000A
+DataRatesID:02 Len:05 Data:02 04 11 22 44
+DomainID:03 Len:06 Data:41 20 30 31 32 40
+ProductID:04 Len:09 Data:TI ACX100
+ManufacturerID:05 Len:07 Data:TI Test
+get_mask 0x00004182, set_mask 0x00000000
+don't know how to get sensitivity for radio type 0x16
+got sensitivity value 0
+got antenna value 0x4A
+got regulatory domain 0x41
+get_mask 0x00000000, set_mask 0x00000000 - after update
+new ratevector: 82 84 0B 0C 12 16 18 24 2C 30 48 60 6C
+setting RXconfig to 2010:0FDD
+acx: === chipset TNETW1130, radio type 0x16 (Radia), form factor 0x01 ((mini-)PCI / CardBus), EEPROM version 0x05: uploaded firmware 'Rev 2.3.1.31' ===
+creating /proc entry driver/acx_wlan%d
+creating /proc entry driver/acx_wlan%d_diag
+creating /proc entry driver/acx_wlan%d_eeprom
+creating /proc entry driver/acx_wlan%d_phy
+acx v0.3.37: net device wlan%d, driver compiled against wireless extensions 22 and Linux 2.6.32.27
+using IRQ 80
+Not using the 00000009 VLYNQ device's driver for VLYNQ device: 00000000
+Not using the 00000029 VLYNQ device's driver for VLYNQ device: 00000000
+registered device TI Avalanche SAR
+Sangam detected
+requesting firmware image "ar0700xx.bin"
+ avsar: firmware: requesting ar0700xx.bin
+avsar firmware released
+tn7dsl_set_modulation : Setting mode to 0xffff
+Creating new root folder avalanche in the proc for the driver stats
+Texas Instruments ATM driver: version:[7.03.01.00]
+</code>
+<code>root@modem1:~# cat /proc/timer_list
 Timer List Version: v0.5
 HRTIMER_MAX_CLOCK_BASES: 2
@@ Line 411: / Line 618: @@
  event_handler:  <9413e26c>
-root@modem1:~# cat /proc/vmallocinfo
+</code>
+<code>root@modem1:~# cat /proc/vmallocinfo
 xc0000000-0xc0043000  274432  pages=66 vmalloc
 xc0044000-0xc0050000   49152  pages=11 vmalloc
@@ Line 418: / Line 627: @@
 xc08fe000-0xc0903000   20480  pages=4 vmalloc
 xc0923000-0xc0926000   12288  pages=2 vmalloc
-root@modem1:~# cat /proc/vmstat
+</code>
+<code>root@modem1:~# cat /proc/vmstat
 nr_free_pages 596
 nr_inactive_anon 241
@@ Line 441: / Line 652: @@
 nr_isolated_anon 0
 nr_isolated_file 0
-nr_shmem 43
+nr_shmem 43</code>
-root@modem1:~# cat /proc/zoneinfo
+<code>root@modem1:~# cat /proc/zoneinfo
 Node 0, zone   Normal
   pages free     595
@@ Line 484: / Line 695: @@
   start_pfn:         81920
   inactive_ratio:    1
-root@modem1:~# cat /proc/mounts
+</code>
+<code>root@modem1:~# cat /proc/mounts
 rootfs / rootfs rw 0 0
 /dev/root /rom squashfs ro,relatime 0 0
@@ Line 497: / Line 710: @@
 /dev/mtdblock4 /overlay jffs2 rw,relatime 0 0
 mini_fo:/overlay / mini_fo rw,relatime 0 0
-root@modem1:~# ifconfig
+</code>
+<code>root@modem1:~# ifconfig
 br-lan    Link encap:Ethernet  HWaddr 00:17:9A:1E:00:00
           inet addr:192.168.1.1  Bcast:192.168.1.255  Mask:255.255.255.0
@@ Line 537: / Line 752: @@
           RX bytes:0 (0.0 B)  TX bytes:12660 (12.3 KiB)
           Interrupt:80
-root@modem1:~# route
+</code>
+<code>root@modem1:~# route
 Kernel IP routing table
 Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
 .168.1.0     *               255.255.255.0   U     0      0        0 br-lan
-root@modem1:~# top
+</code>
+<code>root@modem1:~# top
 Mem: 10088K used, 2400K free, 0K shrd, 640K buff, 2404K cached
 CPU:  57% usr  21% sys   0% nic   2% idle   0% io  17% irq   1% sirq
@@ Line 566: / Line 785: @@
      2 root     SW       0   0%   0% [bdi-default]
 ^C 25     2 root     SW       0   0%   0% [sync_supers]
-root@modem1:~# netstat
+</code>
+<code>root@modem1:~# netstat
 Active Internet connections (w/o servers)
 Proto Recv-Q Send-Q Local Address           Foreign Address         State
@@ Line 580: / Line 801: @@
 unix  2      [ ]         DGRAM                     36331
 unix  2      [ ]         DGRAM                       767
-root@modem1:~# lsmod
+</code>
+<code>root@modem1:~# lsmod
 Module                  Size  Used by    Not tainted
 tiatm                 121280  0

toh/d-link/dsl-624t.1359802341.txt.bz2 · Last modified: 2013/02/02 11:52 by alessandro_s

This text is licensed under a Creative Commons Attribution-ShareAlike 3.0 Unported License.

OpenWrt

Wiki Search

Actions

Donate

Translations

Differences